SloanLED W24 Bright LINE Outdoor Guide d'installation
- Taper
- Guide d'installation
SloanLED BrightLINE Outdoor
Installation Guide for 701989-(X)W24(L,S)C1
PAGE 1 OF 2
WARNING: Risk of electrical shock. Installation requires knowledge of sign electrical systems. If not qualied, do not attempt installation.
Contact a qualied electrician. Follow all national and local codes. SloanLED BrightLINE Outdoor is not suitable for submersion or direct
exposure to water for extended periods of time.
AVERTISSEMENT: Risque de choc électrique. Installation exigent la connaissance des systèmes électriques de signalisation. Si non qualié,
ne tentez pas l'installation. Contactez un électricien qualié. Suivez tous les codes national et locaux. SloanLED BrightLINE Outdoor ne
convient pas à la submersion ni à l'exposition directe à l'eau pendant de longues périodes.
Tools required: Measuring tape, wire strippers,
drill, and screwdriver.
Components list:
• SloanLED 24 V Class 2 output power supply
(refer to "SloanLED Power Supply Guide
for Sign Products" for appropriate 24 V
power supply models)
• UL approved 18 AWG (1 mm²),
or larger diameter supply wire
• UL/CE approved wire connectors
appropriate for wire gauge used
• Optional for mounting: Electrical grade
silicone, #6 (M3) pan or hex head sheet
metal screws, or 1/8" (3 mm) aluminum rivets
Layout: To populate sign, refer to
SloanLED BrightLINE Outdoor density guidelines,
test, or contact your SloanLED Representative
for recommendations.
1. Peel and stick: Clean inside sign with rubbing alcohol and allow to dry. Using predetermined
layout and LED placement from previous step, remove tape backing and stick LED strips into
place. Ensure strips are rmly attached.
2. Fasteners: Use fasteners or silicone
as necessary to x LED strips into place.
Refer to components list above for
acceptable fasteners.
SloanLED Headquarters
5725 Olivas Park Drive, Ventura, CA, USA
888.747.4LED (888.747.4533) • info@SloanLED.com
SloanLED.com
SloanLED Europe b.v.
Argonstraat 110, 2718 SN Zoetermeer, NL
+31 88 12 44 900 • europe@SloanLED.com
P/N 402964 Rev B 2022-02-16
Customer service and technical support
E215393
SloanLED BrightLINE Outdoor
Installation Guide for 701989-(X)W24(L,S)C1
PAGE 2 OF 2
Extension of Power Supply Leads
If longer lead wire from power supply to LED strips is needed, an extension can be used. Extension should be kept as short as possible, i.e., under
15 ft for 18 AWG UL Listed PLTC (4.6 m for 1 mm² PLTC) or under 50 ft for 14 AWG UL Listed PLTC (15.2 m for 2.5 mm² PLTC).
Troubleshooting:
Entire sign or leg does not light
after complete installation.
Check connection from power supply lead to rst LED strip. Make sure polarity of connections made at the power supply lead and
any jumper wire is correct. Power supply outputs should be connected RED-TO-RED and BLACK-TO-WHITE.
Still does not light.
Check output voltage of power supply using a voltmeter. The output voltage should be DC 24.0 V ± 0.5 V. If there is no output
voltage, have a licensed electrician check input voltage. Make sure power supply is connected correctly and getting primary power.
If power supply is connected properly and getting primary power and there is still no output voltage, try a different power supply.
Still does not light.
If power supply is getting primary power and LED strips don’t light, there may be a short in the secondary wiring. Check all
connections and cap all loose wires.
The beginning of a leg lights, but
the entire leg does not light, or
lights intermittently.
The primary cause of a portion of a SloanLED BrightLINE Outdoor leg not lighting or lighting intermittently is a bad connection or
reverse polarity connection between LED strips that light and LED strips that don’t light. Check this connection.
One LED strip does not light, but
all others in the leg light.
SloanLED BrightLINE Outdoor
is designed so if one LED strip fails, it will not cause the entire sign or leg to go out.
If one LED strip does not light, but all others in the leg do, replace this LED strip with a new one.
3.
Connections: LED Strips may be connected in series or parallel, using
appropriate UL/CE Listed wire connectors. Cap all unused wires. Connect
power supply output to rst LED strip on string. See power supply install
guide for more information regarding power supply installation.
NOTE: SloanLED BrightLINE Outdoor Long and SloanLED
BrightLINE Outdoor Short may be connected to same power supply
output. Ensure total power consumption does not exceed 90% of
power supply output rating.
24 VDC Power Supply Capacity Chart
Maximum feet (meters) / LED strips
Power output
SloanLED BrightLINE Outdoor Long
3.3 W/strip, 6.7 W/ft (22 W/m)
SloanLED BrightLINE Outdoor Short
1.1 W/strip, 2.2 W/ft (7.4 W/m)
30 W
(EU/ROW ONLY) 3.9 ft (1.2 m) / 8 strips 11.8 ft (3.6 m) / 24 strips
60 W 7.9 ft (2.4 m) / 16 strips 23.6 ft (7.2 m) / 48 strips
96 W 12.3 ft (3.8 m) / 25 strips 37.9 ft (11.6 m) / 77 strips
3 × 96 W 3 × 12.3 ft (3.8 m) / 25 strips 3 × 37.9 ft (11.6 m) / 77 strips
100 W 13.3 ft (4.1 m) / 27 strips 39.9 ft (12.2 m) / 81 strips
150 W
(EU/ROW ONLY) 19.7 ft (6.0 m) / 40 strips 59.5 ft (18.2 m) / 121 strips
Capacities based on 90% of power supply output.
NOTE: Refer to "SloanLED Power Supply Guide for
Sign Products" for appropriate 24 V power supply models.
Scan QR code to
download SloanLED
Power Supply Guide
for Sign Products
https://sloanled.com/downloads/SloanLEDPowerSupplyGuideForSignProducts.pdf
DO NOT CUT PRODUCT WHEN USED
IN OUTDOOR INSTALLATIONS
-
1
-
2
SloanLED W24 Bright LINE Outdoor Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Autres documents
-
Tetra MiniMAX 12V Wet Location LED Signage Guide d'installation
-
-
-
-
-
-
-
-
Lincoln Electric DC-600 Mode d'emploi
-
Asus PRIME X299-DELUXE II Manuel utilisateur