Package Contents / Installation du matériel / Instalación del hardware
1 2 3
Warning Before Installation
The product must be installed and protected in a location that is not easily accessible, and is away from impacts or
heavy vibration. For example, at the location where the surveillance cameras are looking down or installed at high
positions such as on a wall, or at least 3 meters above the ground.
Before installation, the product should be stored in a
dry and ventilated environment.
The product should be used in compliance with local
laws and regulations.
Use only accessories that comply with the technical
specications of the product.
Do not install the product on an unstable mount or
surface.
Please contact LINEAR'S certied dealers for power
adapters.
Do not disassemble the camera or perform maintenance
task when power is connected.
Avertissement avant installation
Avant l'installation, le produit doit être entreposé dans
un endroit sec et ventilé.
Le produit doit être utilisé conformément aux lois et
réglementations locales.
N'utiliser que des accessoires conformes aux
spécications techniques du produit.
Ne pas installer le produit sur un support ou une surface
instable.
Le produit doit être installé et protégé dans un endroit difcilement accessible, à l'abri des chocs et des vibrations
importantes. Par exemple, à l'endroit où les caméras de surveillance sont dirigées vers le bas ou installées à des
endroits élevés, par exemple sur un poteau, un mur ou au moins à 3 mètres du sol.
Veuillez contacter les revendeurs certiés LINEAR pour
les adaptateurs d'alimentation.
Ne démontez pas la caméra et n'effectuez pas de
travaux de maintenance lorsque celle-ci est sous tension.
Advertencia antes de la instalación
BAntes de la instalación, el producto debe almacenarse
en un entorno seco y ventilado.
El producto debe usarse de acuerdo con las leyes y
regulaciones locales.
Use solo accesorios que cumplan con las
especicaciones técnicas del producto.
No instale el producto en un estante o soporte inestables.
El producto debe instalarse y protegerse en un lugar que no sea fácilmente accesible y donde no se someta a
impactos o fuertes vibraciones. Por ejemplo, en el lugar donde las cámaras de vigilancia miran hacia abajo o se
instalan en posiciones altas, como en un poste, una pared o al menos 3 metros sobre el suelo.
Póngase en contacto con los distribuidores certicados
de LINEAR para los adaptadores de corriente.
No desmonte la cámara ni realice tareas de
mantenimiento cuando esté conectada la alimentación.
IV200 / IV400 Dome/Turret Fixed Lens
Dome/Turret Fixed Lens Camera
RJ45
Connector Cover Alignment Sticker Quick Install Guide
T10
Torx Wrench
Use the included alignment sticker to drill holes on the
wall. If preferred, drill a routing hole on the wall.The
anchors may not be necessary if you install the camera
on a wooden wall or calcium silicate board.
Use the T10 wrench to loosen the retention screws and
remove the top cover.
Route the cables through the routing hole. If you are
using the 12V DC power, use putties to seal the cable
joints for water-proong.
Install a MicroSD card if onboard storage is preferred.
4 5 6Disassemble the cable gland and install the waterproof
seal components to an Ethernet cable.
Mounting Hardware
M4 X 25 1”
unit: mm
8
1
2
M2.5 X 8
72.6
45
26
9.3 5
IV400 IV200 TURRET
IV200
T10
64
GB
10
I
Reset
button
Ø ≥ 1.0”
(25 mm)
(5.5 ~ 6.4mm)
0.22” ~ 0.25”
Replacement
Desiccant Bag
If mounting the camera prior to initial setup with the
NVR, it is a recommended to record the following
information:
1. Model number
2. MAC address
3. Mounting location on the facility
Network Camera
Model No: XXXXXX
MAC: 0002D14BAD55
Pat. 6,930,709
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Made in Taiwan
Quick Installation Guide
78 9
11
10
Secure the camera to wall/ceiling using the included
screws. You may also route the cables through an
opening at the side of the camera base by removing
the side lid.
Connect the Ethernet cable to the camera's RJ45
connector. Fasten the waterproof seal components.
It is best to form a drip loop on the back-end cables. In
some cases, moisture might condense into water drops
and eventually cause problems.
With a live view, pan, tilt, or rotate the lens module to
adjust the shooting direction and acquire the best eld
of view.
Double-click on the camera’s MAC address to open a
web console to the camera.
12
13 14
10030182 Rev-B
Install a ground wire using the included screw.
Replace the desiccant bag on the inside of the top
cover.
Install the top cover, then remove the protective cover.
20AWG
< 10 kgf-cm
OR
PoE
Browser
LAN
IEEE 802.3af/at
2
1
T10
For additional information, download User Manual from:
linear-solutions.com/product-manuals
NOTE
1. The camera requires IEEE 802.3af/at PoE power to function properly. Use
Only UL listed I.T.E active PoE Switch or Mid-Span.
• IV400 also includes 12vdc power input connection.
2. When connected to a Linear NVR directly or over the network, the NVR will
automatically nd the camera regardless of IP network settings.
For direct camera login and management, open a browser to the default IP
Address of 192.168.0.230 username= admin, password = linear
Only one camera should be congured at at time to avoid default IP
Address conicts.
NOTE: Side opening not intended for outdoor use.
Technical Support: (800) 421-1587 • M – F 8am – 7pm EST
Sales & Customer Service: (800) 543-4283 • M – F 8am –
7pm EST
www.linear-solutions.com
©2022 Nortek Security & Control LLC. All rights reserved. Linear is a
registered trademark of Nortek Security & Control LLC.
Nortek Security & Control LLC. 5919 Sea Otter Place, Suite 100, Carlsbad,
CA 92010 USA
-
1
-
2
dans d''autres langues
- English: Linear IV200 Installation guide
- español: Linear IV200 Guía de instalación