INSTALLATION INSTRUCTIONS
PUCK
FM-4514, FM-4516
HARDWARE
Qty: 3 Qty: 2 + 1 Extra
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019 1
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE
CIRCUIT BREAKER BEFORE BEGINNING.
•Read all instructions before installing.
•System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC)
and local regulations.
•When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
•Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the
supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not
designated for use with this product by Modern Forms could result in personal injury or property damage, and will void
the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that
customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
•Lisez toutes les instructions avant l’installation.
•Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et
également aux règlements locaux.
•Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour
être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms.
Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages
corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé
ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire.
Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du
luminaire une fois toutes les deux semaines avec un chiffon humide.
Junction Box Screw
Wire Connector
FIG 1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts
necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Connect the fixture input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors are secure.
If your outlet box has a ground wire (Green or bare copper), connect the fixture’s ground wire to it. After wires are
connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
4. Remove the diffuser from the base plate by twisting it counter-
clockwise.
Discard the foam spacer and secure the base plate to the
junction box using the junction box screws provided.
6. Reinstall the diffuser onto the base plate by twist locking in a
clockwise direction.
5.
3", 4" or 3/0-4/0 Junction Box
Wire Connector
Base Plate
Junction Box Screw
Diffuser
INSTALLATION INSTRUCTIONS
PUCK
FM-4514, FM-4516
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019 2
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
-
1
-
2
dans d''autres langues
Documents connexes
-
Modern Forms PD-52718 Marimba Mode d'emploi
-
-
-
-
-
-
-
-
-