Modern Forms FH-W1803 Axis 44 Flush Mode d'emploi

Axis 52 Flush

Installation Instructions

works with the

Google Assistant

FH-W1803-52

Axis Flush Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FH-W1803-5 2 Axis Flush Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: [email protected]

General Inquiries

Fan Support

FH-W1803-52

Axis Flush Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FH-W1803-52 Axis Flush Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms . Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FH-W1803-52

Axis Flush Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FH-W1803-52 Axis Flush Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Installing the Mounting Bracket 10

3. Hanging the Fan 12

4. Attaching the Fan Blades 14

5. Making the Electrical Connections 14-16

6. Installing the Optional Wall Control 18

7. Finishing the Installation 20

8. Installing the Adapter Plate 20

9. Installing the LED Luminaire Module/Cover 22

10. Controlling the Fan 24

11. Reset 26

12. Breeze Mode 26

13. Application 26

14. Accessories 28

15. Troubleshooting 29-32

FH-W1803-52

Axis Flush Instructions8

Package Contents

7. Glass Shade

RPL-F1803-GLA

8. Luminaire Cover

RPL-FH1803-COVER-**

9. Control Receiver

w/Hardware

F-R3-1803-**

10. Remote w/Wall Cradle

F-RCBT-WT

1. Blade Set of 3

RPL-F1803-**-BD-**

2. Hanger Plate

RPL-F1803-HGR

3. Trim Ring - Decorative

RPL-FH1803-TRIM**

4. Motor Assembly

5. Adapter Plate

6. LED Module

F4IN-120V-R1-30

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

** denotes ﬁnish code of fan/blade sweep

of fan

Hardware Bag

RPL-AXISFLUSH-PART

AMachine Screws (2)

Spring Washers (2)

BWood Screw (1)

Spring Washer (1)

CWire Nuts (8)

DScrew with Fiber Washers (10)

Ø10xØ4mm flat washers (2)

Ø14xØ6mm flat washer (1)

FH-W1803-52 Axis Flush Instructions 9

10

4

9

8

7

5

6

3

2

1

IMPORTANT: Please make note

of the MAC ID on the

receiver and keep it in a

safe place.

MAC ID

Hanging Weight: 13 lbs

FH-W1803-52

Axis Flush Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The outlet

box and support structure must be able to fully support the moving

weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic outlet

boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Figures 1-1C are examples of diﬀerent ways to mount the outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

1. Disconnect power to the fan location at the breaker. A licensed

electrician must install the fan.

2. There are four screws on top of the motor assembly. Remove two

that are on the opposite of each other and save for the Finishing

the Installation section. Loosen remaining two.

3. Pass the 120-volt supply wires through the center hole in the

ceiling mounting bracket as shown (Fig. 2).

4. Secure the hanger plate to the ceiling outlet box with the screws

and washers provided (Fig. 2).

REMEMBER to turn oﬀ power at the breaker.

Follow the steps below to hang your fan properly:

2. Installing the Mounting Bracket

FH-W1803-52 Axis Flush Instructions 11

1

1A 1B

2

1

2

3

1. Support Brace

2. Outlet Box

3. Joist

FH-W1803-52

Axis Flush Instructions12

3. Hanging the Fan

REMEMBER to turn oﬀ power at the breaker.

Follow the steps below to hang your fan properly:

1. Disconnect power at the breaker to the fan location.

Check your outlet box to make sure it has a proper Hot, Neutral,

and Ground. If not, you will need to consult with a licensed

electrician to install a new cUL/UL outlet box (Fig. 3).

2. Remove 1 of 2 screws from the bottom of mounting bracket

and save for use in the Finishing the Installation section. Loosen

the other screw (Fig. 3).

3. Pass the 120-volt supply wires through the center hole

in the ceiling mounting bracket as shown in (Fig. 3A).

4. Secure the mounting bracket to the ceiling outlet box with

the screws and washers provided with your fan.

Use A hardware.

5. Lift motor assembly and hang it on the hook of mounting bracket

using one of the screw holes (Fig. 3B).

6. Secure the safety cable to the building structure using spring

washer, flat washer, and wood screw provided (Fig. 3B).

Use B hardware.

NOTE: Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over 35 lbs. in

both flush and downrod models in the United States.

FH-W1803-52 Axis Flush Instructions 13

Follow the steps below to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

3 3A

3B 3C

1. Screws

2. Top Assembly

A A

B B

4

3

2

1

DO NOT SCALE DRAWING

UPWARD MOUNTING BRACKET

SHEET 1 OF 1

UNLESS OTHERWISE SPECIFIED:

SCALE: 1:5

WEIGHT:

REV

DWG. NO.

B

SIZE

TITLE:

NAME

DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRIC

TOLERANCING PER:

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

ANGULAR: MACH

BEND

TWO PLACE DECIMAL

THREE PLACE DECIMAL

APPLICATION

USED ON

NEXT ASSY

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAME HERE>. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

<INSERT COMPANY NAME HERE> IS

PROHIBITED.

1

2

1. Wood Screw

2. Safety Cable

3. Trim Ring

4. Top Assembly

2

1

3

4

1. 120V Wires

2. cUL Listed Electrical Box

3. Mounting Plate

4. Mounting Screws

(supplied with outlet box)

1

23

4

2

3

1

To Switch A

A

B

(HOT)

(Neutral)

(HOT)/

Switch

(No Neutral)

(Ground)

*Bare or Green

(Ground)

*Bare or Green

To Switch

1. cUL Listed Electrical Box

2. Mounting Screws

(outlet box mounting screws

not included)

3. 120V Wires

FH-W1803-52

Axis Flush Instructions14

4. Attaching the Fan Blades

5. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground and neutral wires) which should run between

ceiling and wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire. Use electrical tape as needed.

Before inserting and wiring the receiver - make note of the MAC ID on

the receiver.

Insert the receiver into the motor assembly with the flat side of the

receiver facing the ceiling (Fig. 5).

1. Insert the blade through the slot in the housing. Align the holes

in the blade with the fan motor assembly holes and secure with

blade attachment screw with lock washers (Fig. 4).

Use C hardware.

2. Repeat this procedure with the remaining blades.

FH-W1803-52 Axis Flush Instructions 15

4

1. Screws with

Rubber Washers

2. Slot

3. Top Assembly

1

3

2

5

1

3

2

1. Motor Assembly

2. Receiver

3. Trim Ring

FH-W1803-52

Axis Flush Instructions16

5. Making the Electrical Connections

Motor to Receiver & Receiver to house supply wires (Fig. 5A).

1. Connect the motor assembly ground wire, mounting bracket

ground wire and receiver ground wire to the ground wire in

outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the black wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FH-W1803-52 Axis Flush Instructions 17

5A

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Assembly Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

HARDWARE USED:

D - Wire Nuts

FH-W1803-52

Axis Flush Instructions18

6. Installing the Optional Wall Control

NOTE: A Bluetooth wall control accessory can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 6).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 6).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 6).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 6).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 6A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 6A).

7. Fasten the wall plate to the wall mounting plate (Fig. 6A).

6

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)

Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

to Fan

From Breaker

* Home Wiring may vary

FH-W1803-52 Axis Flush Instructions 19

6A

Multi-location wiring

1 2 3

54

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wall Plate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 22.

Line/Hot

Red

Green (Green or Bare)

Wallcontroller 1 Wallcontroller 2 Wallcontroller 3

If Applicable

FAN

Neutral/White

Wall Control 1 Wall Control 2 Wall Control 3

FH-W1803-52

Axis Flush Instructions20

7. Finishing the Installation

1. Secure all wire connections with supplied wire ties to assist in canopy

installation.

2. Tuck connections neatly into ceiling outlet box.

3. Remove the motor from the hook on the mounting bracket. Slide the

motor up to the mounting bracket and place the key hole on the motor

over the screw of the mounting bracket (Fig. 7).

4. Turn motor until it locks in place at the narrow section of the

key holes.

NOTE: Make sure the receiver sits flat and does not interfere with

the hook.

5. Align the circular hole on canopy with the remaining hole on the

mounting bracket. Secure by tightening the two screws previously

loosened and the two screws previously removed.

6. Raise up trim ring and line up the 4 tabs with the 4 grooves on the

mounting bracket. Once lined up, slide the trim ring and secure it to

the canopy until snug.

1. Remove one of the three mounting plate screws from the

mounting ring and loosen the other two screws (do not remove).

2. Place the key holes in the mounting plate over the two screws

previously loosened from the mounting ring. Turn the mounting

plate until the adapter plate locks in place at the narrow section

of the key holes (Fig. 8).

3. Tighten the two mounting ring screws previously loosened and

the one previously removed to secure adapter plate.

8. Installing the Adapter Plate

La page charge ...

Modern Forms FH-W1803 Axis 44 Flush Mode d'emploi

Ce manuel convient également à

Modern Forms FH-W1803 Axis 44 Flush Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents