Modern Forms FR-W2201 Wyndmill Mode d'emploi

Marque: Modern Forms

Modèle: FR-W2201 Wyndmill

Catégorie: Ventilateurs ménagers

Taper: Mode d'emploi

Ce manuel convient également à

Wyndmill

Installation Instructions

FR-W2201-65L

Wyndmill Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W2201-65LWyndmill Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FR-W2201-65L

Wyndmill Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W2201-65L Wyndmill Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app.

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting 50 lbs. or less (22.7 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FR-W2201-65L

Wyndmill Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W2201-65L Wyndmill Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Installing the Hanging Bracket 12

3. Attaching the Fan Blades/Arms 12

4. Hanging the Fan 14

5. Making the Electrical Connections 16

6. Installing the Optional Wall Control 18

7. Finishing the Installation 20

8. Installing Adapter Plate 20

9. Installing the Luminaire Module 20

10. Controlling the Fan 22

11. Reset 24

12. Breeze Mode 24

13. Application 24

14. Accessories 26

14. Troubleshooting 27-30

FR-W2201-65L

Wyndmill Instructions8

Package Contents

7. Press Plates

8. Blade Arms

RPL-F2201-BARM-**

9. LED Module

F4IN-120V-R1-30

10. Acrylic Shade

RPL-F2201-GLA

11. Receiver w/ Wire Nuts/Ties

F-R3-2201-065

12. Remote Control

F-RCBT-WT

1. Blades

RPL-F2201-65-BD-**

2. Hanging Bracket/Downrod

Assembly

RPL-HGR-ASM-6-**

3. Canopy & Canopy Screw Ring

RPL-CAN-CYL-**

4. Coupling Cover

RPL-COU-CVR-**

5. Motor Housing

6. Adapter Plate

RPL-F2201-ADP

** Denotes ﬁnish code of fan /blade sweep of fan

* Light assembly and acrylic shade come pre-attached in the package. If you need a light

assembly part (not acrylic shade) - contact the factory. If you need the acrylic shade - order

part no. RPL-F2201-GLA.

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

Hardware Bag

RPL-F2201-PARTS

AMachine Screws (2)

Spring Washers (2)

Flat Washers (2)

BScrews and Washers (36/36

CBlade Arm Screws

1/4” x 1/2”

Wood Screw (1)

Spring Washer (1)

Flat Washer (1)

EWire Nuts (8) (Packed with receiver)

)

(37)

FR-W2201-65L Wyndmill Instructions 9

MAC ID

Hanging Weight: 38 lbs

IMPORTANT: Please make note of

the MAC ID on the receiver and

keep it in a safe place.

FR-W2201-65L

Wyndmill Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 50 lbs. or less 22.7 kg). Do not use

plastic outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Use Part A if needed to mount the outlet box.

Figures 1-1B are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

FR-W2201-65L Wyndmill Instructions 11

1. Support Brace

2. Outlet Box

3. Joist

FR-W2201-65L

Wyndmill Instructions12

2. Installing the Hanger Bracket

Remember to disconnect the power at the circuit breaker.

1. Remove 1 of 2 screws from the bottom of the mounting bracketand

save for use in section 11. Loosen the other screw (Fig. 2).

2. Pass the 120-volt supply wires through the center hole in

themounting bracket as shown (Fig. 2A).

3. Secure the mounting bracket to the ceiling outlet box with

thescrews and washers provided with your outlet box. Use Part A

if needed to mount your Outlet Box.

4. Before you install the blades/blade arms - remove and discardthe

rubber motor stops from the motor housing.

NOTE: Make sure that mounting screws are tight.

1. Attach the blade to blade arm using the screws and washers the

blade press plates on top of the blade and placing the blade on

the blade arm as shown. (Fig. 3/4)

Use Part B.

2. Fasten blade assembly to the outer ring of the motor housing

using the supplied screws (Fig.5). Use Part C

3. Attaching the Fan Blades/Arms

FR-W2201-65L Wyndmill Instructions 13

2 2A

3 4

Mounting Bracket

Screw

To Switch A

(HOT)

(Neutral)

(HOT)/

Switch

(No Neutral)

(Ground)

*Bare or Green

(Ground)

*Bare or Green

To Switch

Mounting Screws

(outlet box screws not included)

120V Wires

cUL/UL Listed Outlet Box

FR-W2201-65L

Wyndmill Instructions14

1. Remove screw from hanger ball. Remove hanger ball and

cross pin. (Fig. 6)

2. Loosen 2 screws, clevis pin and cotter pin (Fig. 6A).

3. Install coupling cover, canopy screw ring, canopy and downrod

assembly into motor housing as shown (Fig. 6).

4. Align downrod and motor collar holes, re-insert pins

and screws (Fig. 6B).

5. Slip up canopy and canopy screw cover. Re-install hanger ball

with cross pin in correct place (Fig. 6A).

6. Seat all into the mounting bracket. Rotate until ball drops and

locks into hanger bracket screw (Fig. 6A).

7. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided (Fig. 6B).

Use Part D.

NOTE: Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over 35 lbs. in

both flush and downrod models in the United States (Fig. 6).

4. Hanging the Fan

FR-W2201-65L Wyndmill Instructions 15

6 6A

FR-W2201-65L

Wyndmill Instructions16

5. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box. Use Part E.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the mounting bracket with the flat side of the

receiver facing the ceiling (Fig. 6).

Motor to Receiver & Receiver to house supply wires (Fig. 6A).

1. Connect the fan assembly ground wire, mounting bracket

ground wire, and receiver ground wire to the ground wire in

the outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

NOTE: Failure to make correct wire connections can permanently

damage the receiver. Make certain you follow the below steps and

diagram.

FR-W2201-65L Wyndmill Instructions 17

Follow the steps below to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

WHITE(for Light)

Mounting Bracket

Receiver

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

RED(to Receiver)

GREY(to Receiver)

YELLOW(to Receiver)

FR-W2201-65L

Wyndmill Instructions18

6. Installing the Optional Wall Control

NOTE: Wall Control not included. A bluetooth wall control accessory

can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 7).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 7).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 7).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 7).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 7A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 7A).

7. Fasten the wall plate to the wall mounting plate (Fig. 7A).

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

From Breaker

* Home Wiring may vary

to Fan

FR-W2201-65L Wyndmill Instructions 19

Multi-location wiring

1 2 3

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wallplate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 22.

Line/Hot

Red

Green (Green or Bare)

Wall Control 1 Wall Control 2 Wall Control 3

If Applicable

FAN

Neutral/White

FR-W2201-65L

Wyndmill Instructions20

7. Finishing the Installation

8. Installing Adapter Plate

1. Secure wire connectors with supplied wire ties.

2. Install canopy to mounting bracket with the screw removed in

section 4 (Fig. 8).

3. Install canopy screw ring as shown (Fig. 8).

1. Remove 1 of 3 screws and loosen the others from the mounting

ring (do not remove).

2. Twist lock adapter plate into place (Fig. 8).

3. Using the screw from the previous step, install the

adapter plate (Fig. 8).

9. Installing the Luminaire Module/Glass Shade

1. Remove the 3 screws from the outer perimeter of the adapter

plate.

2. Attach LED wires from motor assembly to luminaire module

(Fig. 8A).

3. Secure the luminaire module with the 3 screws to the

adapter plate (Fig. 8A).

4. Install the shade by twisting it into place.

Make sure it is on tight. (Fig. 8B).

La page charge ...

Modern Forms FR-W2201 Wyndmill Mode d'emploi

Marque: Modern Forms

Modèle: FR-W2201 Wyndmill

Catégorie: Ventilateurs ménagers

Taper: Mode d'emploi

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Modern Forms FR-W2201 Wyndmill Operating instructions

Modern Forms FR-W2201 Wyndmill Mode d'emploi

Ce manuel convient également à

Modern Forms FR-W2201 Wyndmill Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents