YoLink YS4909-UC Mode d'emploi

YS4909-UC
Marque
YoLink
Modèle
YS4909-UC
Taper
Mode d'emploi
In the Kit
C
Valve Controller
4 x AA Batteries
Motorized Valve
Phillips Head
Screws(3)
Quick Start Guide
Your Valve Controller connects to the
internet via one of our hubs (original
YoLink Hub or the SpeakerHub), and it
does not connect directly to your WiFi or
local network. In order for remote access
to the device from the app, and for
full-functionality, a hub is required. This
guide assumes the YoLink app has been
installed on your phone, and a YoLink
Hub or SpeakerHub is installed and
online.
If installing the Valve Controller and
motorized valve outdoors, please refer to
the environmental range information in
the specifications found on the Valve
Controller product support page. While
this product can be installed outdoors, to
ensure years of trouble-free operation, it
should be protected from rain and direct
sunlight by an enclosure or overhead
cover.
Quick Start Guide
YS4909-UC & DN##
Valve Controller &
Motorized Valve Kit
Revision Feb. 06, 2023
Welcome!
A
Thank you for purchasing YoLink
products! We appreciate you trusting
YoLink for your smart home & automa-
tion needs. Your 100% satisfaction is our
goal. If you experience any problems
with your installation, with our products
or if you have any questions that this
manual does not answer, please contact
us right away. See the Contact Us
section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
Pour des instructions en
français, scannez les codes
QR dans la section suivante.
Para obtener instrucciones en
español, escanee los códigos
QR en la siguiente sección.
Fr
Es
Before You Begin
B
Installation & User
Guide
Product Support
Support produit
Soporte de producto
You can also find all current guides and
additional resources, such as videos and
troubleshooting instructions, on the
Valve Controller Product Support Page
by scanning the QR code below or by
visiting:
https://shop.yosmart.com/pages/
valve-controller-product-support
Please note: this is a quick start guide,
intended to get you started on the
installation of your Valve Controller.
Download the full Installation & User
Guide by scanning this QR code:
LED Behaviors
Blinking Red Once, Then Green
Once
Device Start-Up
Blinking Red And Green
Alternately
Restoring to Factory Defaults
Blinking Red Once
Valve Closing
Quick Blinking Red Twice
Valve is Closed
Blinking Green Once
Valve Opening
Quick Blinking Green
Control-D2D Pairing in Progress
Quick Blinking Red
Control-D2D Unpairing in
Progress
Slow Blinking Green
Updating
Fast Blinking Red Once Every
30 Seconds
Low Battery, Replace Batteries
Soon
Required Items
Locking PliersPipe Wrench
Copper Pipe
Cutting Tool
SandpaperThread Seal Tape
Wall AnchorsDrill with Drill Bits
Medium Phillips
Screwdriver
Marker or Pencil
Pipe Fittings
/Adapters
These tools or items may be required:
DGet to Know Your Valve
Controller, Continued.
F
Get to Know Your Valve
Controller
F
Keyhole Mounting
Slot
Enclosure Clamp
Latches
Combination SET
Button & Status
LED
Cable Connector
Get to Know Your
Motorized Valve
F
The valve included in this kit is a 12VDC
non-smart motorized valve. Use only
this valve or YoLink-approved valve
control products, such as the Bulldog
Valve Robot. Do not use with non-YoLink
valve products.
Manual Control
Knob
Lift, then turn either
clockwise to shut
the valve or
counterclockwise
to open the valve
Valve Position
Indicator
Window indicates
the current position
of the valve. “O”
indicates open, “S”
indicates shut
Valve Control
Cable
The following icons are used in this guide to
convey specific types of information:
Very important information
(can save you time!)
Good to know info but may not apply
to you
Contact Us
K
Power Up, Final
Connections & Testing
J
6. Wrap each adapter’s threaded end
with thread seal tape, per the tape
manufacturer’s instructions, as shown
below.
7. Install the motorized valve on the
adapter fittings, ensuring a secure
connection at each fitting, as shown
below.
8. At the water valve or point of
disconnection, turn the water on again.
9. Verify there are no leaks and no visible
water on the motorized valve.
1. At the desired location for the
controller, confirm the cables of the two
devices will reach each other. Holding
the controller at the desired location, and
using a marker or similar means, mark
the location of the mounting hole to the
wall or mounting surface.
2. If you are using a wall anchor, install it
at this time, per the manufacturer’s
instructions.
3. Secure the Valve Controller to the wall
or mounting surface with a screw, as
shown.
1. Install batteries in the Valve Controller.
This is done by releasing the two clamp
latches on the side of the controller, then
opening the cover. Then, install the
batteries.
2. Close the cover, snapping the clamp
latches tightly into the locked position.
3. Connect the Valve Controller's cable to
the control cable of the motorized valve.
Ensure the arrow on the cable connector
aligns with the arrow on the other cable
connector. Twist the collar of the
connector tight.
4. The Valve Controller will appear offline
until it is turned on and it wirelessly
connects to a YoLink hub. Turn on the
Valve Controller by pressing the SET
button, just long enough for the LED to
illuminate. It should blink red, then green,
which indicates the Valve Controller has
connected to the cloud.
5. Test the Valve Controller and
motorized valve by pressing the SET
button and listening for the smooth
closing/opening of the valve, and by
checking the water flow at a faucet. The
water should be completely turned off
while the valve is in the shut position.
Refer to the full installation and user
guide to complete the setup of your
Valve Controller and motorized valve.
Your Valve Controller is supplied with
alkaline batteries. If you elect to replace
the batteries with lithium type batteries,
please note, in very cold temperatures,
the battery level may be indicated in the
app as lower than it actually is. This is
characteristic of lithium batteries.
3. Cut the water pipe through the mark
using a pipe cutting tool, then remove
the cut section of pipe, as shown below.
4. Sand both ends of cut pipe, removing
any burrs or rough edges. Use care
handling the cut edges, which may be
sharp! Wipe off the cut section of pipe
with a clean cloth.
5. Install your adapter fittings in the pipe
ends, per the manufacturer instructions.
Add Your Valve Controller
to the App
G
1. Tap Add Device (if shown) or tap the
scanner icon:
Scanner icon
2. Approve access to your phone’s
camera, if requested. A viewfinder will be
shown on the app.
3. Hold the phone over the QR code so
that the code appears in the viewfinder.If
successful, the Add Device screen will be
displayed.
4. Follow the instructions to add your
Valve Controller to the app.
Install the Valve
Controller, Continued.
H
Preparing for installation:
Determine where you will install your
Valve Controller. Typically, it should be
wall-mounted, no farther away from the
motorized valve than the length of the
cables allow (if you have purchased
optional extension cables, the valve
controller can be installed at a location
separate from the motorized valve).
Determine how you will mount the valve
controller to the wall, and have hardware
and anchors appropriate for the wall
surface on hand.
Install the Valve
Controller
H
1. Shut-off the water serving the pipe
where the valve is to be installed. Drain
the water from the pipe, by turning on a
faucet, or by other method as required.
2. Depending on the adapter fitting used,
measure the length of pipe that must be
cut, and mark the cut lines on the pipe,
as shown below.
Install the Motorized
Valve
I
Install the Motorized
Valve, Continued.
I
We are here for you, if you ever need any
assistance installing, setting up or using
a YoLink app or product!
Need help? For fastest service, please
email us 24/7 at [email protected]
Or call us at 831-292-4831 (US phone
support hours: Monday - Friday, 9AM to
5PM Pacific)
You can also find additional support and
ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code:
Finally, if you have any feedback or
suggestions for us, please email us at
[email protected]
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
Support
Home Page
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2022 YOSMART, INC IRVINE,
CALIFORNIA
  • Page 1 1
  • Page 2 2

YoLink YS4909-UC Mode d'emploi

YS4909-UC
Marque
YoLink
Modèle
YS4909-UC
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents