Chief CMS380 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
CMS380 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
CMS380 does not exceed 500 lbs (226.8 kg).
•The weight capacity of the CMS380 may be LIMITED
to the lowest weight capacity of any other component
or accessory used within the mounting system.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: The CMS380 accessory is to be used vertically
ONLY! Do NOT install accessory to pipe or truss horizontally.
WARNING: Do not use this accessory outdoors.
NOTE: Accessory is intended to be used with the UL Listed
CPA Extension Column Series (not included).
IMPORTANT ! : The CMS380 accessory is designed for
installation to a steel supporting truss or pipe with an
outside diameter between 1.75" (44.45mm) and 2.0"
(50.8mm).
IMPORTANT ! : The CMS380 accessory is intended to
be used with the UL listed CMS Pipe Series and a 1-1/2"
NPT or NPSM following ANSI/ASME B1.20.1 (Schedule
40, 0.154" minimum thickness steel or aluminum-ASTM
B221) threaded extension column (not included).
--SAVE THESE INSTRUCTIONS--
Installation Instructions CMS380
3
DIMENSIONS
2.38
60.3
CMS380 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions CMS380
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32"
(security)
A (1)
[CMS accessory]
B (1)
5/16”
C (1)
5/32”
(security)
CMS380 Installation Instructions
6
Assembly And Installation
Display Enclosure Assembly
1. Turn knob counter-clockwise until the knob and retaining
washer can be removed from the upper bar on the clamp.
(See Figure 1)
2. Open the clamp so that it can be installed around a pipe or
truss. (See Figure 1)
Figure 1
3. Wrap opened clamp around pipe or truss at desired
mounting location. (See Figure 2)
Figure 2
4. Pull lower part of clamp up to its original position. (See
Figure 3)
5. Tighten knob until clamp is securely installed to pipe or
truss. (See Figure 3)
Figure 3
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
CMS380 does not exceed 500 lbs (226.8 kg).
• The weight capacity of the CMS380 may be
LIMITED to the lowest weight capacity of any
other component or accessory used within the
mounting system
6. Install 1-1/2" NPT or NPSM following ANSI/ASME B1.20.1
(Schedule 40, 0.154" minimum thickness steel or aluminum
- ASTM B221) threaded extension column (not included)
into threaded collar until tight, with a minimum of four
threads engaged. (See Figure 4)
7. Use 5/16” security set screw (B) to secure column. (See
Figure 4)
Figure 4
1
2
retaining washer
3
5
4
(B)
76
CMS380 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002872 Rev00
2016 Milestone AV Technologies
www.milestone.com
12/16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief CMS380 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief CMS380 Installation guide