1
INSTALLATION INSTRUCTIONS
QUILL- LED Pendant
PD-59413S/PD-59425S/PD-59441S
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus
pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
A
Wire Connector
Qty: 3pcs+1 Extra
B
Mounting screw
Qty: 12pcs+1 Extra
Hardware
C
Plastic Anchor
Qty: 16pcs+1Extra
Anchor Screw
Qty: 16pcs+1Extra
D
2
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
INSTALLATION INSTRUCTIONS
FIG. 1
QUILL - LED Pendant
PD-59413S/PD-59425S/PD-59441S
Instruction: Adjust the xture wire
length by pushing the
cable gripper on the canopy
and pulling the wire as desired.
Push up
Cable gripper
Junction Box
Anchor Screw
Mounting Screw
Wire Connector
Mounting Back Plate
Plastic Anchor
Safety Cable
Junction Box Screw
Driver
Switch Cover
Canopy
4CCT Switch
Wire
Conduit
Glass Lamp Body
Lamp Base
A
C
B
D
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING MOUNTING PLATE (Fig. 1)
3. Remove the mounting screws (B) and take out the mounting plate.
4. Using the mounting plate as a template, drill holes in the ceiling aligned with the outer set of holes located in the mounting plate. Insert the
plastic anchors (C) into the ceiling.
5. Recommended to use UL approved >100LB max outlet box and hardware (sold separately). If standard duty JB is used, make sure adding
adequate fastening to secure the fixture to carry the weight. See weight table below.
6 . First, secure the mounting plate to the junction box using the junction box screws (not provided). Second, fasten the mounting plate to the
ceiling using anchor screws (D).
(i) The side of the mounting plate marked “GND” must face out, towards the installer.
(ii) It is recommended to use only original junction box screws or replacements provided by junction box manufacturer.
WIRING AND HANGING FIXTURE (Fig. 1, Fig. 2, Fig. 3, Fig. 4)
7. Set color temperature at this stage. The xture can switch between four color temperatures (2700K, 3000K, 3500K, 4000K), which can be adjusted
to your preference using the 4CCT switch (Fig. 2) mounted in the canopy.
Note: the switch comes with a detachable cover, remove the cover prior to
adjusting the color temperature, reattach the cover after adjustment is made.
8. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
(i) Before securing the canopy in place, it is recommended to retract or extend the wire within the canopy to a desirable length.
(ii) Due to limited space within the canopy, shorten the cable as necessary to make the installation easier. Make sure to identity and label
all the wiring properly before any trimming/shortening of cables. (Fig. 4)
(iii) Note: Retracting or extending excessive cable length through the cable gripper is not recommended.
(iv) Warning: Modifying the xture may result in voiding the warranty of the product. Only licensed persons should trim cables and perform rewiring.
9. Attach the xture to the mounting plate using a safety cable as shown (Fig. 1). This secures the xture and aids in wiring.
10. Connect the drivers’ input wires to the junction box wires as shown (Fig. 3) using wire connectors (A) provided. Ensure wire connectors are secure.
Connect the xture’s ground wire to the ground in the junction box; this will be either a green wire or a bare copper wire. After driver is wired to
house wires, tuck wires carefully inside the junction box.
11. If using a dimmer with this xture, wire dimmer connections at this stage per section titled “(OPTIONAL) DIMMER WIRING.”
12. Mount the canopy against the mounting plate and rotate it. Secure xture to the mounting plate using the mounting screws (B).
INSTALLING LAMP BODY (Fig. 1)
13. Place the glass lamp body on the lamp body base.
14. Tighten the conduit down to the base of the lamp body.
(OPTIONAL) DIMMER WIRING (Fig. 3)
- This xture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes
below for specic dimming wires information.
- To utilize ELV or TRAIC dimming: use wires black (live), white (neutral) and house green wire or bare copper wire (ground). Do not use dimmer wires on driver
for ELV or TRAIC dimming.
- To utilize 0-10V dimming: use wires purple (dim+), Pink or gray (dim-) from driver and connect to corresponding wires in junction box.
- NOTE: Make sure to connect 0-10V prior to powering up the xture in order to allow the 0-10V dimming to function properly.
INSTALLATION INSTRUCTIONS
QUILL - LED Pendant
PD-59413S/PD-59425S/PD-59441S
3
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 3 Wiring
Fig. 4 Driver Wires
White - Neutral
Black - Live
Canopy
Red +
Black -
Black -
Driver
Input
Output
Purple - Dim+
Pink or Gray
- Dim-
Green +
Blue W
Bare W
Brown C
White C
4CCT Switch
Product Number Weights lbs
PD-59425S 84.7
PD-59441S 139.3
Product Weight
Fig.2 4CCT Switch
4000K 3500K 3000K 2700K
4000K 3500K 3000K 2700K
INSTALLATION INSTRUCTIONS
QUILL - LED Pendant
PD-59413S/PD-59425S/PD-59441S
4
Phone (800) 526.2588
Fax (800) 526.2585
44 Harbor Park Drive
Port Washington, NY 11050
1600 Distribution Ct
Lithia Springs, GA 30122
1750 Archibald Avenue
Ontario, CA 91760
Dec. 2023
PD-59425S
Mounting Plate Dimensions
Driver Wires For
PD-59403R/59405R/59409R/59415R/59421R
PD-59413S
PD-59441S
3000 K 2700 K4000 K 3500 K
Input
Driver
Output
(1000MA)
White - Neutral Black - Hot
DC+
Red
DC-
Black
Brown
Switch
Blue
Black
Green+
Bare W-
White C-
Bare W-
Green+
Bare W-
Green+
White C-
White C-
3000 K 2700 K4000 K 3500 K
Input
Driver
Output
(700MA)
White - Neutral Black - Hot
DC+
Red
DC-
Black
Brown
Switch
Blue
Black
Green+
Bare W-
White C-
Bare W-
Green+
White C-
18 1/8"
18 1/8"
1 3/4"
1 3/8"
26 1/8"
26 1/8"
1 3/4"
1 3/8"
34 1/8"
34 1/8"
1 3/4"
1 3/8"
-
1
-
2
-
3
-
4
WAC Lighting PD-59441S Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
WAC Lighting PD-59423L Mode d'emploi
-
-
-
-
-
-
-
-
-