B&B Electronics Access Converter/ 3 Mode d'emploi

B&B Electronics
Marque
B&B Electronics
Modèle
Access Converter/ 3
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
International Headquarters
B&B Electronics
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 — General Fax (815) 433-5105
Email: [email protected]
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 — Fax +353 91-79244S5
Email: techSupport@bb-elec.com
Website: www.bb-elec.com
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for any
errors that may appear in this document. Access Converter/3 is a trademark of B&B Electronics. Other brands or product
names may be trademarks and are the property of their respective companies.
Document Number 52-80141-00 A2 Revised August 2013
If the product’s part number begins with an “8”, it is compliant with the Restriction of Hazardous Substances (RoHS)
directive.
Access
Converter/ 3
Operation Manual
ii
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B Electronics warrants that each such
product shall be free from defects in material and workmanship for its lifetime. This limited lifetime warranty is
applicable solely to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation, connection, operation and maintenance of
products in accordance with their written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any warranty or indemnity offered by B&B
Electronics, but may be subject to the warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics have any warranty obligations or any
other liability for: (i) any defects resulting from wear and tear, accident, improper use by the buyer or use by any third
party except in accordance with the written instructions or advice of the B&B Electronics or the manufacturer of the
products, including without limitation surge and overvoltage conditions that exceed specified ratings, (ii) any products
which have been adjusted, modified or repaired by any party other than B&B Electronics or (iii) any descriptions,
illustrations, figures as to performance, drawings and particulars of weights and dimensions contained in the B&B
Electronics’ catalogs, price lists, marketing materials or elsewhere since they are merely intended to represent a general
idea of the products and do not form part of this price quote and do not constitute a warranty of any kind, whether
express or implied, as to any of the B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN ACCORDANCE WITH THE EXPRESS WARRANTY SET
FORTH ABOVE IS B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE WARRANTY
CONTAINED IN THIS SECTION SHALL EXTEND TO THE ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES ARE EXPRESSLY
DISCLAIMED, INCLUDING WITHOUT LIMITATION (I) THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE AND OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS ARE DO NOT INFRINGE
OR VIOLATE THE INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B
ELECTRONICS BE LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS,
LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES.
B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY REPRESENTATIONS, WARRANTIES OR
INDEMNITIES MADE BY ANY OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES, DISTRIBUTORS,
RESELLERS OR DEALERS OF B&B ELECTRONIC WHICH ARE INCONSISTENT WITH THE WARRANTY, SET FORTH
ABOVE.
7
NOTE
6
SAFETY CERTIFICATIONS
UL/CUL: Listed to Safety of Information Technology Equipment, including
Electrical Business Equipment.
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (89/336/EEC) and the Council
Directive on Electrical Equipment Designed for use within Certain
Voltage Limits (73/23/EEC). Certified to Safety of Information
Technology Equipment, Including Electrical Business Equipment. For
further details, contact B&B Electronics.
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this
equipment.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
iii
TABLE OF CONTENTS
FCC Radio Frequency Interference Statement .................................................... ii
Limited Lifetime Warranty .................................................................................. ii
About the Access Converter/3 ........................................................................... 1
Installing the Access Converter/3 ....................................................................... 2
LED Operation .................................................................................................. 3
Specifications .................................................................................................... 5
Safety Certifications ........................................................................................... 6
iv
NOTES:
5
SPECIFICATIONS
DC Input Voltage:
AC Adapter Input Load: 100/240 ±10% VAC, 0.25A, 50/60 Hz, 5 VDC output with
maximum output current of 1A Unit Power Consumption (Typical): 600 mA @ 5
VDC
Operating Temperature:
32° to 122° F (0° to 50° C)
Storage Temperature:
-4° to 158° F (-20° to 70° C)
Humidity:
5 to 90% (non-condensing); 0 to 10,000 ft. altitude
Dimensions:
H=0.92” W=3.50” D=4.00” (2.3 x 8.9 x 10.2 cm)
4
Fiber Uplink Port
The LED indicator for the fiber uplink port is located on the RJ-45 connector of the
downlink port next to the power connector. There are four LED functions for the
fiber uplink port.
The fiber uplink port LED functions are as follows:
•
Glows green when a link is established on the fiber port.
•
Glows green indicating a valid link, then blinks green when activity is detected
on the fiber port.
•
When the LED is OFF, there is no link (check cabling, check remote device).
•
Blinking LED - indicates the device attached to the other end of the fiber
maybe passing Link Fault Propagation, or generating noise onto the fiber. This
normally happens when there is a media converter at the fiber end of the link.
Connect the second port of the converter onto a valid device to generate link.
Twisted Pair Uplink Port
When the Access Converter/3 is configured with a twisted pair uplink port, the LED
location and functionality is the same as that for the downlink ports.
1
ABOUT THE ACCESS CONVERTER/3
The Access Converter/3 is a 10/100 auto-negotiating, switching, optical access
product. There is one uplink port and three 10/100 twisted pair downlink ports.
The uplink port can be either fiber or 10/100 twisted pair. The uplink port is
located on the back of the media converter. Each of the twisted pair ports can
auto-sense the speed and duplex mode of a connected device. These speeds
include the following:
•
10 Mbps
•
100 Mbps
•
Half Duplex
•
Full Duplex
All of these speeds include Flow Control. The fiber port always operates at 100
Mbps Full Duplex.
The Access Converter/3 offers plug-and-play operation, including the AutoCross
feature which automatically selects between a crossover work-station or straight-
through repeater hub connection depending on the connected device.
The Access Converter/3 also protects against Broadcast storms, and allows packets
of up to 1916 bytes to pass. The Access Converter/3 uses a universal external
switching power adapter for 100 to 240 ±10% VAC input and 5 VDC output
(included).
2
INSTALLING THE ACCESS CONVERTER/3
Install the Access Converter/3 as a table-top device, or mount to a wall surface with
the appropriate bracket (included). To wall mount, use the supplied screws to
attach the wall-mount bracket to the Access Converter/3, then simply mount the
unit to the wall by tightening the screws (not supplied).
Note
The Access Converter/3 packaging also includes four small rubber “feet” for use in
table-top or wall-mount installations.
Plug the Access Converter/3 into a power source and attach the connected devices.
Verify installation by observing the LEDs on the unit (refer to the LED Operation
section for more information).
Wall Mount Bracket
Screw holes for mounting unit to the wall.
Wall-mount bracket must be attached
to the bottom of the unit.
Screw holes for mounting
wall-mount bracket with
supplied screws
3
LED OPERATION
Each Access Converter/3 includes diagnostic LEDs for troubleshooting.
Front
Back
Twisted Pair Downlink Ports
The LED indicator for the twisted pair downlink port is located on the RJ-45
connector of the downlink port next to the power connector. There are two LED
functions for the twisted pair downlink ports. LED functions are as follows:
•
Glows amber when a link is established on the copper port
•
Glows amber indicating a valid link, then blinks amber when activity is
detected on the copper port.
Note
The
g
reen LED on RJ-45 connectors
are
reserved for future use, with one
exception— refer to the following Uplink Port sections for more information.
Uplink LED
Fiber Uplink
LED
TX Downlink LED
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

B&B Electronics Access Converter/ 3 Mode d'emploi

B&B Electronics
Marque
B&B Electronics
Modèle
Access Converter/ 3
Catégorie
Convertisseurs de média réseau
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents