LG Electronics ADFD5448AT Manuel utilisateur

OWNER'S MANUAL

DISHWASHER

Read this owner's manual thoroughly before operating the

appliance and keep it handy for reference at all times.

ENGLISH

ADFD544***

MFL71467502

Rev.02_091120

www.lg.com

TABLE OF CONTENTS

2

3 IMPORTANT SAFETY

INSTRUCTIONS

3 READ ALL INSTRUCTIONS BEFORE USE

3 WARNING STATEMENTS

6 CAUTION STATEMENTS

7 PRODUCT OVERVIEW

7 Product Features

9 INSTALLATION

9 Before Installing

10 Preparing Cabinet Opening

11 Preparing Water and Electrical Connections

12 Preparing Dishwasher

13 Sliding Dishwasher into Cabinet Opening

14 Connecting Water Supply Line and Power

15 Connecting the Drain Hose

17 Leveling Dishwasher

18 Securing Dishwasher in Cabinet Opening

19 Final Installation Check

21 OPERATION

21 Before Using

25 Control Panel

26 Wash Cycles

27 Options and Extra Functions

28 Loading the Dishwasher

29 Loading the Silverware Basket

29 Loading the Lower Rack

31 Loading the Upper Rack

33 Adding Cleaning Products

36 SMART FUNCTIONS

36 LG ThinQ Application

38 Smart Diagnosis

TM

Function

39 MAINTENANCE

39 Cleaning and Care

42 TROUBLESHOOTING

42 Before Calling for Service

49 LIMITED WARRANTY

49 USA

53 CANADA

57 APPENDIX

57 ADA Compliance

3IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING STATEMENTS

WARNING

• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this

product, follow basic precautions, including the following:

Installation

• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

• To reduce the risk of severe injury or death, follow all installation instructions.

• The appliance must be installed and electrically grounded by qualified service personnel in accordance

with local codes.

• Disconnect the power supply line, house fuse or circuit breaker before installing or servicing the

appliance.

• When moving or installing the product in a different location, call qualified service personnel for

installation and service.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Moving or installation of the appliance requires two or more people.

• This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or

aircraft.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions.

• This appliance must be positioned near to an electrical power supply.

• Do not, under any circumstances, cut or remove the ground from the power supply line.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages

will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

4 IMPORTANT SAFETY INSTRUCTIONS

• When installing or moving the appliance, be careful not to pinch, crush, or damage the power supply

line.

• Do not install the appliance in humid spaces.

• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children

might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight

chambers.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged power supply line.

• Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and

safety glasses.

• The installer must ensure that the dishwasher is completely enclosed at the time of installation.

• Use new hoses when connecting the appliance to the water supply. Do not reuse old hoses.

• After installing, check the hose connection for leaks.

• Do not damage or place heavy items on the power supply line of the appliance.

Operation

• Repair or immediately replace all power supply lines that have become frayed or otherwise damaged. Do

not use a power supply line that shows cracks or abrasion damage along its length or at either end.

• If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug

it immediately, and contact an LG Electronics customer information center.

• Never unplug the appliance by pulling on the power supply line.

• Do not use an extension cable or adapter with this appliance.

• Do not grasp the power supply line or touch the appliance controls with wet hands.

• Do not modify or extend the power cable.

• If the product has been submerged, contact an LG Electronics customer information center for

instructions before resuming use.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

• Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags,

etc.), gasoline, chemicals and other flammable vapors and liquids.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• If the electrical supply line is damaged, it must only be replaced by the manufacturer or its service agent

or a similar qualified person in order to avoid a hazard.

• Do not abuse, sit on, or stand on the door of the appliance.

• Read all instructions before using the appliance and save these instructions.

• Use this appliance only for its intended purpose.

• Do not allow children to play on, in or with the appliance. Close supervision of children is necessary when

the appliance is used near children.

• Do not tamper with controls.

• In the event of a gas leak (propane gas, LP gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for

such a period, before using the appliance turn on all hot water faucets and let the water flow from each

for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

5IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• Fix the drain hose securely in place.

• Use only detergents or wetting agents recommended for use in a dishwasher and keep them out of the

reach of children.

• Do not let children eat detergent or dishwasher rinse agent.

• When loading items to be washed:

- Locate sharp items so that they are not likely to damage the door seal.

- Load sharp knives with the handles up to reduce the risk of cuts or other injuries.

• Do not wash plastic items unless they are marked "dishwasher safe" or the equivalent. For plastic items

not so marked, check the manufacturer’s recommendations.

• Do not touch the HEATING ELEMENT during or immediately after use.

• Do not operate your dishwasher unless all ENCLOSURE panels are properly in place.

• Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

• Do not install or store the dishwasher where it will be exposed to weather conditions.

• After cleaning the dishes, turn off the water supply. Before cleaning, turn the water supply back on and

check the connections.

• Do not open the appliance door while it is operating. For safety reasons, the drain pump operates if the

door is opened, resulting in a longer cycle time.

• Be careful not to catch your hand when closing the door of the product.

• Do not plug the dishwasher into a damaged outlet.

• Do not install or keep the dishwasher near electrical components or exposed flames.

• Do not wash dishes exposed to gasoline, solvents or other flammable materials.

• When cleaning, do not spray water on the product directly.

• Do not press buttons with a sharp object such as an awl or pin.

• Do not use solvent-based detergent.

• Do not come into contact with the steam outlet.

• Small parts, such as rack clips and filter retaining posts can be a choke hazard to small children if

removed from the dishwasher. Keep out of reach of small children.

Maintenance

• Do not repair or replace any part of the appliance. All repairs and servicing must be performed by

qualified service personnel unless specifically recommended in this Owner’s Manual. Use only

authorized factory parts.

• Do not disassemble or repair the appliance by yourself.

• Remove any dust or foreign matter from the power supply line.

• Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply.

• Remove the door before the appliance is removed from service or discarded to avoid the danger of

children or small animals getting trapped inside.

• Unplug the appliance before cleaning to avoid the risk of electric shock.

• Before discarding the appliance, cut off the power supply line and destroy the appliance's control panel.

Grounding Instructions

• This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of least resistance for electric current.

• This appliance is equipped with a cord having an equipment-grounding conductor and a grounding

plug.

6 IMPORTANT SAFETY INSTRUCTIONS

• The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with

all local codes and ordinances.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative if you are in doubt whether the appliance is properly

grounded. Do not modify the plug provided with the appliance, if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Tip Over Hazard

• Do not use the dishwasher until completely installed.

• Do not push down on the open dishwasher door.

• Failure to follow these instructions may result in serious injury or cuts.

CAUTION STATEMENTS

CAUTION

• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or

property when using this product, follow basic precautions, including the following:

Installation

• Install the product on a firm and level floor.

• This dishwasher must be connected to a hot water supply with a temperature range between 120 °F (49

°C) and 149 °F (65 °C). This temperature range provides the best washing results and shortest cycle time.

The temperature should not exceed 149°F (65 °C) to prevent damage to dishes.

• Do not put the drain hose under the dishwasher during installation.

Operation

• Do not place objects on top of the appliance.

• Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period

of time, such as during vacations.

• Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the

appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.

• Do not touch draining water which may be hot.

• If the drain hose and the water supply hose are frozen in winter, defrost before using the appliance.

• Do not put hands, feet, or metal objects below or behind the appliance.

Maintenance

• If cooking oil is spilled on the exterior of the product, wipe it off immediately. Do not clean the exterior of

the product with cleaners which contain alcohol, thinners, bleach, benzene, flammable liquids, or

abrasives. These substances may discolor or damage the appliance.

7PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

NOTE

• For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of separately purchased

unauthorized components or parts.

• Do not remove the safety cover at any time.

• To ensure reliability, each LG dishwasher goes through thorough quality control before it leaves the

factory.

• You may find water droplets or water spots from this process inside your new dishwasher.

Front View

a Control Panel

b Front Cover

c Lower Cover

d Shipping Brace

e Safety Cover

f Drain Hose

g Power Cord

h Base

i Leveling Feet

Interior View

a Top Wash Impeller

b Upper Spray Arm

c Cutlery Basket

d Lower Spray Arm

e Dishwasher Salt Cover

f Filtration System

g Detergent and Rinse Aid Dispenser

h Upper Rack

i Lower Rack

NOTE

• The silverware basket ships installed at the back

of the bottom rack. For best performance, install

it along the right side.

8 PRODUCT OVERVIEW

NOTE

• Remove all packing materials from the exterior

and interior of the dishwasher before installing

the appliance.

Accessories

a Installation Brackets (2 ea)

b Wood Screws (4 ea)

c Hose Clamp

d Funnel

e Lower Cover

f Moisture Barrier Tape (Aluminum Tape)

g Moisture Barrier Tape (Side Aluminum Tape)

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

a

b

c

Model ADFD5448AT

Electrical Requirements 120 V, 60 Hz AC only, minimum 15 A circuit breaker

Min. / Max. Water Pressure 20 psi - 80 psi (140 kPa - 550 kPa)

Dimensions

(Width X Depth X Height)

23 1/2" X 22 1/2" X 32 1/16"

(598 mm X 572 mm X 815 mm)

Inlet Water Temperature 120 ℉ (49 ℃) minimum, 149 ℉ (65 ℃) maximum

Net Weight 84 lbs. (38 kg)

9INSTALLATION

ENGLISH

INSTALLATION

Before Installing

Parts not Provided

Tools Needed

Installation Overview

Please read the following installation instructions

first after purchasing this dishwasher or

transporting it to another location.

a Preparing Cabinet Opening

b Preparing Water and Electrical Connections

c Preparing Dishwasher

d Sliding the Dishwasher into Cabinet Opening

e Connecting Water Supply Line and Power

f Connecting the Drain Hose

g Leveling the Dishwasher

h Securing Dishwasher in Cabinet Opening

i Final Installation Check

a

Water Supply Tube

d

Air Gap

g

Baseboard (Wood)

b

Fittings for Tube

e

Hose Clamp

c

Coupler

f

3/4" Elbow

a

Flat-Blade Screwdriver

f

Safety Glasses

k

1/4” Square Drive Wrench

b

Phillips Screwdriver

g

Adjustable Wrench (2)

l

Pliers

c

Hole Saw min. 2 1/2” bit

h

Tape Measure

m

3/8" Square Drive Wrench +

1/2" Socket

d

Electrical Drill

i

Utility Knife

n

Saw

e

Gloves

j

Level

10 INSTALLATION

Product Dimensions

Front View

Side View

Preparing Cabinet Opening

This dishwasher is designed to fit a standard

dishwasher opening. An opening may be needed

on both sides to route plumbing and electrical

connections.

• To ensure proper drainage, install the

dishwasher no more than 12 ft. (3.65 m) from

the sink.

• The location must have sufficient space for the

dishwasher door to open easily and provide at

least 0.1” (2 mm) between the dishwasher and

the cabinet sides.

• If installing the dishwasher in a corner, leave a

minimum of 2” (50 mm) between the dishwasher

and the adjacent wall.

• The adjacent wall must be free of obstructions.

• For flush installations only, you may remove the

cabinet brace

a inside the cabinet.

Choosing the Proper Location

1 Select a location as close to the sink as

possible for easy connections to water supply

line, drain hose and electrical connection.

2 To allow for proper clearance of plumbing

and electrical, use the template included with

the literature to determine the clearance on

the side of the cabinet where the cabinet

meets the back wall. Using a 2 1/2” diameter

hole saw, drill a hole in the target area as

shown on the template.

WARNING

• Installation damage is not covered by the

warranty, and leaks caused by improper

installation may result in property damage.

• Do not use existing holes unless they are in the

target area.

• Failure to properly locate the hole for the water

and drain lines may prevent the dishwasher

from installing flush with the cabinets and could

18”

(455 mm)

23 1/2”

(598 mm)

22 1/2”

(572 mm)

32 1/16”

(815 mm)

45 1/2” (1155 mm)

Max. 24"

(610mm)

Min. 23 5/8"

(600mm)

32 1/4 " - 34 1/2 "

(820 - 876 mm)

Max. 24"

(610mm)

Ma

(61

4 "

(100 mm)

3 "

(75 mm)

11INSTALLATION

ENGLISH

result in kinked, pinched, crushed, stressed or

damaged lines.

Installing Moisture Barrier Tape

Install the moisture barrier tape to the underside

of the countertop to protect the surface from

condensation when the appliance is opened.

1 Clean and dry the area on the underside of

the countertop and the sides of the cabinet

opening where the tape will be applied.

2 Remove the protective film from the tape.

3 Install the tape on the underside of the

countertop.

4 Install the shorter pieces of tape on the sides

of the cabinet opening at the top.

NOTE

• Moisture barrier tape is included in the manual

assembly bag.

• If the countertop is made of granite or

waterproof materials, the moisture barrier tape

is not required.

• Condensation may occur on the underside or

along the front edge of the countertop when the

room temperature is low.

Preparing Water and

Electrical Connections

WARNING

• Water Connection

- Do not reuse an old hose. Use only a new hose

when installing the dishwasher. The old hose

could leak or burst causing flooding and

property damage. Contact an LG Customer

Information Center for assistance in buying a

new hose.

• Electrical Connection

- Use a time-delay fuse or circuit breaker.

- Operate this appliance with the correct voltage

as shown in this manual and on the rating

plate.

- The wiring must be grounded properly. If in

doubt, have it checked by a qualified

electrician.

- Connect the appliance using 3-wires, including

a ground wire.

- The appliance and outlet must be positioned

so that the plug is easily accessible.

- Do not use an extension cable or adapter with

this dishwasher.

- Do not overload the outlet with more than one

appliance.

- The included 16AWG wire nuts should be used.

- It is the personal responsibility and obligation

of the product owner to have a proper outlet

installed by a qualified electrician.

CAUTION

• When connecting the dishwasher water supply

line to the house water supply, sealing tape or

compound should be used on pipe threads to

avoid leaks. Tape or compound should not be

used on compression fittings.

• Connect the dishwasher to a hot water supply

with a temperature range between 120 °F (49 ℃)

and 149 °F (65 ℃). This temperature range

provides the best washing results and shortest

cycle time. To prevent damage to dishes, the

temperature should not exceed 149 °F (65 ℃).

12 INSTALLATION

CAUTION

• Water supply pressure must be between 20 psi

and 80 psi (140–550 kPa). If the water supply

pressure exceeds 80 psi, a pressure reducing

valve must be installed. Otherwise premature

failure of the inlet valve may occur.

Connecting Water Supply Line and

Power

Water supply tube: Minimum 3/8″ O.D. copper

tubing or metal braided dishwasher supply line

1 Connect the elbow a to the inlet valve on the

back of the dishwasher.

2 Connect the water supply tube to the elbow.

3 Tighten both connections using two

adjustable wrenches to avoid putting stress

on the water inlet valve.

4 Make sure the water supply is turned off.

Connect the water supply tube to the tap.

5 Insert the power plug into an outlet.

6 Turn on the water and check for leaks at the

connections.

• If there is a leak, reconnect the elbow.

• Do not cross thread or overtighten the

connections to avoid leakage.

7 Unplug the power cord.

8 Turn off the water supply and disconnect the

water supply tube at the tap.

Preparing Dishwasher

WARNING

• Do not remove safety cover. Removal can result

in fire, electric shock or death.

Releasing Drain Hose

Remove the twist tie holding the drain hose to the

back of the shipping brace.

13INSTALLATION

ENGLISH

Removable Shipping Brace

The rear shipping brace can be removed if

additional clearance is needed when installing the

dishwasher under a low countertop.

Removing Packing Materials from

the Interior

Remove all packing materials from the interior of

the dishwasher before installing the appliance.

CAUTION

• Take care when opening or closing the appliance

door before the custom door panel is installed.

The door may open or close abruptly without the

weight of the panel.

Attaching Installation Brackets

For countertops made of wood or other materials

that will not be damaged by drilling, use the metal

installation brackets provided.

For countertops made of granite, marble, or other

materials that could be damaged by drilling, use

the wood screws to attach the dishwasher to the

cabinet. See installation instructions in Securing

Dishwasher to Cabinet Opening.

NOTE

• Installation brackets and screws can be found in

the silverware basket.

1 Insert the tabbed end of the installation

brackets into the slots in the upper frame.

Rotate the brackets until the tabbed ends are

facing up.

2 Bend the tabs on the brackets to secure them

to the frame using a pair of needle nose

pliers.

Sliding Dishwasher into

Cabinet Opening

How to Slide Dishwasher

CAUTION

• Do not pull or lift the dishwasher using the

handle

a. Doing so can damage the door and

hinges.

• Do not push the door of the dishwasher with

knees when sliding the dishwasher into position.

Doing so can damage the front cover.

14 INSTALLATION

CAUTION

• Do not push the top of the dishwasher. Doing so

can damage the interior of the dishwasher.

NOTE

• Open the door and grab the body frame and the

top front opening b of the tub to move or lift the

dishwasher.

1 Align the dishwasher with the opening. Make

sure the water supply line and power cord

extend smoothly without kinks or bends.

2 Smooth out or pad the edges of the hole

drilled for the water supply to avoid damaging

the drain hose.

3 Make sure the drain hose is straight before

feeding the end of it through the hole for the

water supply. As you slide the dishwasher into

the opening, slowly pull on the drain hose

from inside the cabinet to take up some slack.

Be careful not to kink, pinch, crush or stress

the drain hose during installation to avoid

leaking and water damage.

4 Gradually slide the dishwasher into the

opening, making sure that the water supply

line and power cord are passing freely

through the opening and do not get caught

under the dishwasher.

• As you slide the dishwasher into the

opening, stop periodically (or have an

assistant help) to take up the slack by

pulling the drain hose farther into the

cabinet.

CAUTION

• To avoid malfunctions or leakage, it is important

that the drain hose not get kinked, pinched,

stressed or crushed behind or under the

dishwasher or inside the neighboring cabinet.

• Damage resulting from improper installation is

not covered under the warranty.

Connecting Water Supply

Line and Power

Connecting Water Supply Line

1 With the home water supply turned off,

connect the water supply tube to the tap.

15INSTALLATION

ENGLISH

2 Tighten the connection using a square drive

wrench to avoid putting stress on the water

tap.

Connecting Power

Insert the power plug into a grounded outlet.

• The power cord should not be positioned behind

the appliance but within 47.2 inches of the side

so that the plug is easily accessible.

WARNING

• Do not use an extension cord or 2-prong

adapter.

• The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

• Connect to a properly rated, protected, and sized

power circuit to avoid electrical overload.

Connecting the Drain Hose

If the end of the drain hose does not fit the drain

line, use a heat and detergent resistant adapter

(not supplied). These may be obtained from a local

plumbing supply store.

• Cut the adapter so the end matches the size of

the drain connection.

NOTE

• For drain hose installation, use the screw style

hose clamp provided with this dishwasher in the

silverware basket.

• If connecting the dishwasher’s drain hose to the

garbage disposal, be sure to follow your

garbage disposal’s manual for proper

installation instructions.

Drain Hose Requirements

• Follow local codes and ordinances.

• Do not exceed 12 ft. (3.65 m) distance to drain.

• Do not connect drain hoses from other

appliances to the dishwasher’s drain hose.

• If an extension drain hose is required, use a 5/8"

or 7/8" inside diameter, 2-3 ft. length hose and a

coupler for connecting the two hose ends.

Height of the Drain Hose

The height of the drain hose end must be at least

12" (305 mm) and within 40" (1016 mm) from the

base of the dishwasher to avoid water being

siphoned from the tub.

Connecting to Disposal without Air

Gap

1 Remove the knockout plug on the disposal

with a hammer and screwdriver.

16 INSTALLATION

2 Remove the knockout plug a from the

disposal.

WARNING

• If the knockout plug has not been removed, the

dishwasher will not be able to drain properly.

3 Attach the drain hose to the disposal with the

hose clamp provided. Move the hose clamp

into position and tighten it with a flat-blade

screwdriver.

Connecting Waste Tee without Air

Gap

The height of the drain hose end must be at least

12” (305 mm) and within 40” (1016 mm) from the

base of the dishwasher to avoid water being

siphoned from the tub.

1 Remove the knockout plug with a hammer

and screwdriver.

CAUTION

• If the knockout plug has not been removed, the

dishwasher will not be able to drain properly.

2 Attach the drain hose to the waste tee with

the hose clamp provided. Move the clamp into

position and tighten it with a flat-blade

screwdriver.

Connecting to Disposal or Waste

Tee with Air Gap

1 Remove the knockout plug with a hammer

and screwdriver.

2 Connect the end of the drain hose a to the air

gap

b with the hose clamp provided. Move

the clamp into position and tighten it with a

flat-blade screwdriver.

• This avoids water being siphoned from the

tub.

3 If it is not connected, attach the rubber hose

connector to the disposal or waste tee with a

hose clamp (not provided).

17INSTALLATION

ENGLISH

Leveling Dishwasher

Check that the dishwasher is level and adjust the

leveling feet if necessary.

CAUTION

• Failure to level the dishwasher may result in

leakage, problems closing the door, or noise.

• Where the cabinet opening is narrower than

recommended (see Preparing Cabinet

Opening), the dishwasher must be carefully

leveled and aligned so that the dishwasher is

supported fully by the 3 leveling feet and is not

hanging from the installation brackets. Failure to

do so can result in leaks from the front of the

dishwasher,

AE errors, difficulty in closing the

door, or failure to operate.

Checking Leveling

To check that the tub is level from front to back,

remove the lower rack and pour 135 oz. (4 L) of

water into the bottom of the tub. The water level

should be near the center of both tub lower

indentations at the front.

With the lower rack removed, place a level on the

inside wall of the tub to check that the dishwasher

is level from side to side.

• If you do not have a level, try using a

smartphone level application instead.

Make sure that the gap between the tub walls and

the door liner is the same on either side.

Adjusting Leveling Feet

Adjust as needed until the dishwasher is

completely leveled.

• Adjust the front and rear leveling feet until they

are all in firm contact with the floor. Failure to

level the dishwasher may prevent the door from

closing properly and the dishwasher will not turn

on.

Adjusting Front Leveling Feet

Use a flat-blade screwdriver to turn the front

leveling feet and adjust the front of the tub.

• Turn the front leveling feet clockwise to raise the

front of the tub and counterclockwise to lower it.

• The adjustments work identically for both front

leveling feet.

• When a flat-blade screwdriver is unavailable, use

a 1/4" square drive wrench

a or 3/8" square

drive wrench

b with 1/2" socket c to turn the

front leveling feet and adjust the front of the tub.

Max 2 3/8”

(60 mm)

18 INSTALLATION

Adjusting Rear Leveling Foot

Use a Phillips screwdriver to adjust the rear

leveling foot and the rear of the tub using the

center screw at the base of the appliance in the

front.

• Turn the center screw clockwise to raise the rear

of the tub and counterclockwise to lower it.

NOTE

• To avoid damaging the screw, do not use an

electric screwdriver.

Securing Dishwasher in

Cabinet Opening

There are 2 options for securing the dishwasher. If

the countertop is made of wood or a material that

can safely be drilled into, secure the dishwasher to

the countertop with the provided brackets. If the

countertop is granite, marble, or a material that

cannot be drilled into, secure the dishwasher to

the cabinet frame with the provided wood screws.

CAUTION

• Ensure the dishwasher is level and all leveling

feet are in firm contact with the floor before

attaching the dishwasher to the countertop or

cabinet. If the dishwasher is not leveled

properly, the door may not close properly or

water may leak.

NOTE

• Installation brackets and screws can be found in

the silverware basket.

• Use a magnetic screwdriver.

• Cover the filter hole with towels to prevent

screws from falling down into the pump.

Securing Dishwasher to Countertop

Use the bracket screws provided to secure the

brackets at the top of the dishwasher to the

underside of the wood countertop.

Securing Dishwasher to Cabinet Frame

If desired, the dishwasher can also be secured to

the cabinet frame using the instructions which

follow.

1 Remove the 2 plastic caps from the mounting

bracket access holes.

2 Drive a wood screw through the mounting

bracket and into the cabinet frame.

3 Reinstall the plastic caps.

Attaching Toe Kick

1 Attach the provided lower cover to the base of

the dishwasher.

19INSTALLATION

ENGLISH

2 Attach a custom toe kick. If needed, use a saw

to cut a notch in the top of the custom toe kick

to provide clearance for the cabinet panel

when opening the door.

Final Installation Check

Testing the Dishwasher

Check if the dishwasher is properly installed.

1 Turn on the circuit breaker.

2 Turn on the house water supply.

3 Make sure that the door opens and closes

smoothly.

• If necessary, level the dishwasher again.

• If the door will not close, make sure the rack

is level.

• Make sure that all packaging materials have

been removed.

4 Power on the dishwasher and run a Turbo

cycle to verify proper operation.

5 Check for leaks at the drain hose and water

supply connection.

6 If a water leak is detected, press and hold the

Start button for 3 seconds to cancel the wash

cycle and automatically drain the water from

the dishwasher. Tighten all water connections

and run another cycle. Repeat until no leaks

are detected.

Installation Check Error Codes

Refer to the chart below before calling for service.

Error Code Possible Cause and Solution

OE

Drain hose is kinked or pinched.

• Feed the drain and water

supply hoses through the hole

under the sink. Then gradually

slide the dishwasher into the

cabinet while pulling on the

hoses under the sink to take up

any slack. This helps avoid

kinking the hoses or trapping

them beneath the dishwasher.

Drain hose is connected to the

disposal without removing the

knockout plug.

• Remove the knockout plug

from the disposal.

Waste tee or disposal is clogged.

• Remove knockout plug on the

waste tee or disposal.

20 INSTALLATION

IE

Water supply line is kinked

under dishwasher.

• Feed the drain and water

supply hoses through the hole

under the sink. Then gradually

slide the dishwasher into the

cabinet while pulling on the

hoses under the sink to take up

any slack. This helps avoid

kinking the hoses or trapping

them beneath the dishwasher.

House water supply is not turned

on.

• Turn the water faucet on.

Error Code Possible Cause and Solution

La page charge ...

LG Electronics ADFD5448AT Manuel utilisateur

Ce manuel convient également à

LG Electronics ADFD5448AT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents