Arthur_Martin AW6C4824CS Manuel utilisateur

Marque: Arthur_Martin

Modèle: AW6C4824CS

Catégorie: Sèche-linge

Taper: Manuel utilisateur

AW6C4824CS

EN Tumble Dryer User Manual

CONTENTS

Safety information 2

Safety instructions 4

Product Description 6

Control Panel 6

Programme table 7

Options 9

Settings 10

Before first use 12

Daily use 13

Hints and tips 14

Care and cleaning 15

Troubleshooting 18

Technical data 20

Quick guide 22

Subject to change without notice.

SAFETY INFORMATION

Before beginning the installation and use of this appliance,

carefully read the supplied instructions. The manufacturer is

not responsible for any injuries or damage that are the result

of incorrect installation or usage. Always keep the

instructions in a safe and accessible location for future

reference.

Children and vulnerable people safety

WARNING!

Risk of suffocation, injury or permanent disability.

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

from the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away

from the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• Do not change the specification of this appliance.

• If the tumble dryer is put on top of a washing machine, use

the stacking kit. The stacking kit, available from your

authorized vendor, can be used only with the appliance

specified in the instructions supplied with the accessory.

Read it carefully before installation (refer to the Installation

leaflet).

• The appliance can be installed as freestanding or below a

kitchen counter with correct space (refer to the Installation

leaflet).

• Do not install the appliance behind a lockable door, a

sliding door or a door with a hinge on the opposite side,

that would prevent the appliance door from being fully

open.

• The ventilation opening in the base must not be covered

by a carpet, mat, or any floor covering.

• CAUTION: The appliance must not be supplied through an

external switching device, such as a timer, or connected to

a circuit that is regularly switched on and off by a utility.

• Connect the mains plug to the mains socket only at the

end of the installation process. Make sure that the mains

plug is accessible after installation.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Do not exceed the maximum load of 8 kg (refer to the

"Programme chart" chapter).

• Do not use the appliance if items have been soiled with

industrial chemicals.

• Wipe away lint or packaging debris that has accumulated

around the appliance.

• Do not run the appliance without a filter. Clean the lint filter

before or after each use.

• Do not dry unwashed items in the tumble dryer.

• Items that have been soiled with substances such as

cooking oil, acetone, alcohol, petrol, kerosene, spot

removers, turpentine, waxes and wax removers should be

washed in hot water with an extra amount of detergent

before being dried in the tumble dryer.

• Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes or

pillows fitted with foam rubber pads should not be dried in

the tumble dryer.

• Fabric softeners, or similar products, should only be used

as specified by the product manufacturer’s instructions.

• Remove all objects from items that could be a source of

fire ignition such as lighters or matches.

• WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use the appliance

where the temperature can be lower

than 5°C or higher than 35°C.

• The floor area on which the appliance

is to be installed must be flat, stable,

heat resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Always keep the appliance vertical

when it is being moved.

• The rear surface of the appliance must

be put against a wall.

• When the appliance is in its permanent

position, check if it is levelled correctly

with the aid of a spirit level. If it is not,

adjust the feet accordingly.

Electrical connection

WARNING! Risk of fire and

electric shock.

• The appliance must be earthed.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Do not touch the mains cable or the

mains plug with wet hands.

Use

WARNING! Risk of injury,

electric shock, fire, burns or

damage to the appliance.

• This appliance is for household

(indoors) use only.

• Do not dry damaged (torn, frayed)

items that contain padding or fillings.

• If laundry has been washed with a stain

remover, carry out an additional rinse

cycle before starting a drying cycle.

• Dry only fabrics that are suitable to dry

in the appliance. Follow the cleaning

instruction on the item label.

• Do not drink or prepare food with the

condensed water/distilled water. It can

cause health problems to people and

pets.

• Do not sit or stand on the open door of

the appliance.

• Do not dry dripping wet clothes in the

appliance.

Internal lighting

WARNING! Risk of injury.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

humidity, or are intended to signal

information about the operational status

of the appliance. They are not intended

to be used in other applications and are

not suitable for household room

illumination.

• To replace the internal lighting, contact

the Authorised Service Centre.

Care and cleaning

WARNING! Risk of injury or

damage to the appliance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Use only neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal

objects.

Service

• To repair the appliance contact the

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

1 2

Water container

Control panel

Appliance door

Filter

Rating plate

Airflow slots

Heat Exchanger lid

Heat Exchanger cover

Adjustable feet

For ease of loading laundry or

ease of installation the door is

reversible. (see separate

leaflet).

CONTROL PANEL

89 7 6

Programme knob and RESET switch

Display

Minuterie (Time Dry) touch button

Départ/Pause (Start/Pause) touch

button

Départ Différé (Delay Start) touch

button

Anti-froissage (Extra Anticrease) touch

button

Délicats (Delicates) touch button

Séchage (Dryness Level) touch button

On/Off button

Press the touch buttons with

your finger in the area with the

symbol or name of the option.

Do not wear gloves when you

operate the control panel.

Make sure that the control

panel is always clean and dry.

Display

Symbol on the display Symbol description

time drying option on

delay start option on

indicator:

check Heat Exchanger

indicator:

clean filter

indicator:

drain the water container

child lock on

wrong selection or knob is in the "Reset" position

programme duration

time Drying duration

delay start duration

PROGRAMME TABLE

Programme

Load

Properties / Fabric type

Coton (Cotton)

Eco

8 kg

Cycle to be used to dry cotton with

"cotton cupboard" dryness level,

with maximum energy saving.

Programme

Load

Properties / Fabric type

Coton (Cotton) 8 kg

Cycle defined to dry all types of

cotton ready to store (cupboard

dry).

Synthétiques (Synthetic) 3,5 kg Synthetic and mixed fabrics.

Délicats (Delicates) 4 kg

Delicate fabrics such as viscose,

rayon, acrylic, and their blends.

Facile à repasser (Easy

Iron)

1 kg (or 5

shirts)

Easy care fabrics for which a mini‐

mum of ironing is necessary. The

drying results can be different from

one type of fabric to another.

Shake the items before putting

them in the appliance. When the

programme has ended, immediate‐

ly remove the items and put them

on a hanger.

Rafraîchir (Refresh) 1kg Refreshing textiles that were in storage.

Chemises (Shirts)

1,5kg (or

7 shirts)/

Easy care fabrics for which a mini‐

mum of ironing is necessary. The

drying results can be different from

one type of fabric to the other.

Shake the items before you put

them in the appliance. When the

programme is completed, Immedi‐

ately remove the items and put

them on a hanger.

Duvet (Duvet) 3 kg

Single or double duvets and pillows

(with feather, down or synthetic fil‐

lings).

Draps (Bedlinen) 3kg

Bed linen such as single and dou‐

ble sheets, pillowcases, duvet cov‐

er.

Sports (Sports) 2 kg

Sportswear, thin and light fabrics,

microfiber, polyester.

Denim (Denim) 4 kg

Leisure clothing such as jeans,

sweat-shirts of different material

thicknesses (e.g. at the neck, cuffs

and seams).

Programme

Load

Properties / Fabric type

Mixtes (Mixed) 3kg

Cotton and synthetic fabrics. Low

temperature programme. Delicate

programme with warm air.

The maximum weight refers to dry items.

For fabric mark meaning see chapter HINTS AND TIPS: Preparing the laundry.

The

Coton (Cotton) Prêt à Ranger (Cupboard Dry) ECO programme is the “Standard cotton programme”

according to Commission Regulation EU No. 392/2012. It is suitable for drying normal wet cotton laundry and it is

the most efficient programme in terms of energy consumption for drying wet cotton laundry.

OPTIONS

Séchage (Dryness Level)

This function helps to increase dryness of

the laundry. There are 3 options:

• Très Sec (Extra Dry)

• Prêt à Ranger (Cupboard Dry)

• Prêt à repasser (Iron Dry)

Délicats (Delicates)

With this option you can set a delicate

drying programme that has a low

temperature. Use this option with a fabrics

that have the symbol on the fabric label

(e.g. acrylic, viscose).

Anti-froissage (Extra

Anticrease)

Extends the anti-crease phase by 60

minutes at the end of the drying cycle.

This function reduces creases. The

laundry can be removed during the anti-

crease phase.

Minuterie (Time Dry)

You can set the programme duration, from

a minimum of 10 minutes to a maximum of

2 hours. The required duration is related

to the quantity of laundry in the appliance.

We recommend that you set a

short duration for small

quantities of laundry or for only

one item.

TIME DRYING RECOMMENDATION

10 - 20 min

action of cool

air only (no

heater).

20 - 40 min

additional dry‐

ing to improve

dryness after

previous dry‐

ing cycle.

>40 min

full drying of

the small laun‐

dry loads up to

4 kg, well

spun (>1200

rpm).

Options table

Programmes

Séchage (Dryness

Level)

Délicats

(Delicates)

Anti-frois‐

sage (Ex‐

tra Anti‐

crease)

Minuterie

(Time Dry)

Coton (Cotton)

Eco

■ ■ ■

Coton (Cotton) ■ ■ ■ ■ ■ ■

Synthétiques (Syn‐

thetic)

■ ■ ■ ■ ■ ■

Délicats (Delicates) ■ ■ ■

Facile à repasser

(Easy Iron)

■ ■ ■

Rafraîchir (Refresh) ■ ■

Chemises (Shirts) ■ ■ ■

Duvet (Duvet) ■ ■

Draps (Bedlinen) ■ ■ ■ ■ ■

Sports (Sports) ■ ■

Denim (Denim) ■ ■ ■ ■

Mixtes (Mixed) ■ ■ ■ ■

Together with the programme you can set 1 or more options. To activate or deactivate them, press the related

touch button.

SETTINGS

A B C

A. Minuterie (Time Dry) touch button

B. Départ/Pause (Start/Pause) touch

button

C. Départ Différé (Delay Start) touch

button

D. Anti-froissage (Extra Anticrease) touch

button

E. Délicats (Delicates) touch button

F. Séchage (Dryness Level) touch button

Child lock function

This option prevents children playing with

the appliance while a programme is

operating. The touch buttons are locked.

Only the on/off button is unlocked.

Activating the child lock option:

1. Press the on/off button to activate the

appliance.

2. Press and hold touch button (D) for a

few seconds.

The child lock indicator comes on.

It is possible to deactivate the

child lock option while a

programme operates. Press

and hold the same touch

buttons until the child lock

indicator goes off. The Child

Lock function isn't available for

8 s after switching on the

appliance.

Adjustment of remaining

laundry moisture

Every time you enter in the

"Adjustment of remaining

laundry moisture" mode,

previously set degree of

remaining moisture will change

into next value ( e.g previously

set will change into

To change the default degree of remaining

moisture:

1. Press the on/off button to activate the

appliance.

2. Use the programme knob to set any

programme.

3. Wait approximately 8 seconds.

4. Press and hold buttons (F) and (E) at

the same time.

One of these indicators comes on:

• the maximum dryness

• the more dry laundry

• the standard dry laundry

5. Press and hold buttons (F) and (E)

again until the indicator of the correct

level comes on.

If the display returns to the

normal mode (the time of

the selected programme

from step 2. will be

displayed), while setting the

degree of remaining

moisture, press and hold

buttons (F) and (E) once

again to enter to the

"Adjustment of remaining

laundry moisture" mode

(previously set degree of

remaining moisture will

change into next value).

6. After 5 s the display returns to normal

mode.

Water container indicator

By default, the water container indicator is

on. It comes on when the programme is

completed or when it is necessary to

empty the water container.

If a draining kit is installed

(additional accessory), the

appliance automatically drains

the water from the water

container. In this case we

recommend that you deactivate

the indicator of the water

container.

Deactivating the water container

indicator:

1. Press the on/off button to activate the

appliance.

2. Wait approximately 8 seconds.

3. Press and hold touch buttons (E) and

(D) at the same time.

The display shows one of these 2

configurations:

• The display shows "Off". After 5 s

the display returns to normal mode.

• The display shows "On". After 5 s

the display returns to normal mode.

Buzzer on/off

To deactivate or activate the acoustic

signals, press and hold for approximately

2 seconds touch buttons (A) and (C) at

the same time.

BEFORE FIRST USE

Rear drum locks are removed

automatically when dryer is

activated for the first time.

Possible to hear some noise.

To unlock the rear drum locks:

1. Switch on the appliance.

2. Set any programme.

3. Press the Start/Pause button.

Drum starts to rotate. Rear drum locks are

automatically deactivated.

Before you use the appliance to dry

items:

• Clean the tumble dryer drum with a

moist cloth.

• Start a 1 hour programme with moist

laundry.

Unusual smell

The appliance is tightly packed.

After product unpacking you can feel an

unusual smell. This is normal for brand

new products.

Appliance is built of several different types

of material which all together can generate

unusual smell.

Over usage time, after few drying cycles

unusual smell gradually disappears.

Noises

Different noises may be heard

at different times during the

drying cycle. They are perfectly

normal operating sounds.

Rotating drum.

Working fans.

Working pump and transferring

condensation to the tank.

DAILY USE

Start a programme without

delay start

1. Prepare the laundry and load the

appliance.

CAUTION! Make sure that

when you close the door,

the laundry does not get

caught between the

appliance door and the

rubber seal.

2. Press the on/off button to activate the

appliance.

3. Set the correct programme and

options for the type of load.

The display shows the programme

duration.

Real drying time will depend on

type of the load (quantity and

composition), the room

temperature and the humidity

of your laundry after spin drying

phase.

4. Press the Départ/Pause (Start/Pause)

touch button.

The programme starts.

Starting the programme with

delay start

1. Set the correct programme and

options for the type of load.

2. Press the delay start button again and

again until the display shows the delay

time you want to set.

You can delay the start of a

programme from a

minimum of 1 hour to a

maximum of 20 hours.

3. Press the Départ/Pause (Start/Pause)

touch button.

The display shows the countdown of the

delay start.

When the countdown is completed, the

programme starts.

Change a programme

1. Press the on/off button to deactivate

appliance

2. Press the on/off button to activate the

appliance.

3. Set the programme.

Alternatively:

1. Rotate the selector knob to the

"Reset" position.

2. Wait for 1 second. The display shows

3. Set the programme.

At the end of the programme

When the programme is completed:

• An intermittent acoustic signal

operates.

• The display shows

• The indicators Filtre (Filter) and

Bac (Tank) comes on.

• The Départ/Pause (Start/Pause)

indicator is on.

The appliance continues to operate with

the anti-crease phase for approximately

30 minutes or more if Anti-froissage (Extra

Anticrease) option was set (see chapter

Option - Anti-froissage (Extra

Anticrease)

The anti-crease phase reduces creasing.

You can remove the laundry before the

anti-crease phase is completed. We

recommend, for better results, that you

remove the laundry when the phase is

almost completed or completed.

When the anti-crease phase is completed:

• The display still shows

• The indicators Filtre (Filter) and

Bac (Tank) comes on.

• Départ/Pause (Start/Pause) indicator

goes off.

1. Press the on/off button to deactivate

the appliance.

2. Open the appliance door.

3. Remove the laundry.

4. Close the appliance door.

Possible causes of unsatisfactory drying

results:

• Inadequate default dryness level

settings. See chapter

Adjustment of

default dryness level

Always clean the filter and

empty the water container

when a programme is

completed.

Stand-by function

To reduce energy consumption, this

function automatically deactivates the

appliance:

• After 5 minutes if you do not start the

programme.

• After 5 minutes from the end of the

programme.

The time is reduced to 30

seconds if the selector knob is

pointing to "Reset" position.

HINTS AND TIPS

Preparing the laundry

Very often the clothes after

washing cycle are kneaded and

tangled altogether.

Drying kneaded and tangled

clothes is inefficient.

To assure proper air flow and

even drying it is recommended

to shake and load one by one

the clothes to the tumble dryer.

To assure proper drying process:

• Close the zips.

• Close the fasteners of duvet covers.

• Do not dry ties or ribbons loose (e.g.

apron ribbons). Tie them before you

start a programme.

• Remove all items from pockets.

• Turn items with the internal layer made

of cotton inside out. Cotton layer must

be faced outwards.

• Always set the programme suitable for

the type of laundry.

• Do not put light and dark colours

together.

• Use suitable programme for cottons,

jersey and knitwear to reduce

shrinkage.

• Do not exceed the maximum load

stated in the programmes chapter or

shown on the display.

• Dry only the laundry that is suitable for

tumble drying. Refer to the fabric label

on the items.

• Do not dry large and small items

together. Small items can be trapped

inside the large items and remain wet.

• Shake the large clothes, fabrics before

placing in the tumble dryer. It is to

avoid moist places inside the fabric

after the drying cycle.

Fabric label Description

Laundry is suitable for tumble drying.

Fabric label Description

Laundry is suitable for tumble drying at higher temperatures.

Laundry is suitable for tumble drying at low temperatures only.

Laundry is not suitable for tumble drying.

CARE AND CLEANING

Cleaning the filter

CAUTION! Avoid the use of

water to clean the filter. Instead

throw away lint in the dustbin

( avoid dispersion of plastic

fiber in water ambient).

To achieve the best drying

performances clean the filter

regularly , clogged filter lead to

longer cycles and energy

consumption increase.

Use your hand to clean the

filter , and if necessary , a

vacuum cleaner .

1. 2.

3. 4.

If necessary remove fluff from the filter socket and gasket. You can use a vacuum cleaner.

Emptying the water container

1. 2.

3. 4.

You can use the water from the

water container as an

alternative to distilled water

(e.g. for steam ironing). Before

you use the water, remove dirt

residues with a filter.

Cleaning the Heat Exchanger

1. 2.

3. 4.

5. 6.

7. 8.

9. 10.

Cleaning the humidity sensor

CAUTION! Risk of humidity

sensor damage. Do not use

abrasive materials or steel wool

to clean the sensor.

To assure best drying results the

appliance is equipped with metal humidity

sensor. It is placed on the inner side of the

door area.

Over usage time the surface of the sensor

may get dirty what deteriorates the drying

performance.

We recommend to clean the sensor at

least 3 or 4 times or if you observe the

drop of drying performance.

To clean you can use harder side of dish-

washing sponge and bit of vinegar or dish

soap.

To clean the sensor:

1. Open the loading door.

2. Clean the surfaces of the humidity

sensor wiping off the metal surface

several times.

Cleaning the drum

WARNING! Disconnect the

appliance before you clean it.

Use a standard neutral soap detergent to

clean the inner surface of the drum and

drum lifters. Dry the cleaned surfaces with

a soft cloth.

CAUTION! Do not use

abrasive materials or steel wool

to clean the drum.

Cleaning the control panel and

housing

Use a standard neutral soap detergent to

clean the control panel and housing.

Use a moist cloth to clean. Dry the

cleaned surfaces with a soft cloth.

CAUTION! Do not use furniture

cleaning agents or cleaning

agents which can cause

corrosion.

Cleaning the airflow slots

Use a vacuum cleaner to remove fluff from

the airflow slots.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

Error Codes

The appliance does not start or it stops during operation.

First try to find a solution to the problem (refer to the table). If the problem persists,

contact the Authorised Service Centre.

WARNING! Deactivate the appliance before carrying out any check.

In case of major problems, the acoustic signals operate, the display shows an

error code and the Départ/Pause (Start/Pause) button may flash continuously:

Error code Possible cause Remedy

E5A

Appliance motor overloaded.

Too much laundry or entrap in the

drum.

The programme was not comple‐

ted. Remove the laundry from the

drum, set the programme and re‐

start the cycle.

E97

Internal fail. No communication be‐

tween electronic elements of the

appliance.

The programme was not finished

properly or the appliance stoped

too early. Switch the appliance off

and on again.

If the error code appears again,

contact the Authorised Service

Centre.

Error code Possible cause Remedy

EH0

The mains supply is unstable. When the appliance is showing

EH0, please wait until main supply

is stable than press start. If the ap‐

pliance pause the cycle without

any indication then press the cycle

start. If the warning will occur

check the power cord / socket in‐

tegrity or main supply.

If the display shows other error codes, deactivate and activate the appliance. If the

problem continues, contact the Authorised Service Centre.

In case of different problem with the tumble dryer check the table below for possible

solutions.

Troubleshooting

Problem Possible solution

You cannot activate the appliance. Make sure that the mains plug is connected

to the mains socket.

Check fuse in fuse box (domestic installa‐

tion).

The programme does not start. Press Départ/Pause (Start/Pause).

Make sure that the appliance door is closed.

The appliance door does not close. Make sure that the installation of the filter is

correct.

Make sure that the laundry is not caught be‐

tween the appliance door and the rubber

seal.

The appliance stops during operation. Make sure that the water container is empty.

Press Départ/Pause (Start/Pause) to start

the programme again.

Load is too small, increase the load or use

the Minuterie (Time Drying) programme.

The cycle time is too long or unsatisfactory

drying result.

Make sure that the weight of the laundry is

suitable for the duration of the programme.

Make sure that the filter is clean.

The laundry is too wet. Spin the laundry in

the washing machine again.

Problem Possible solution

Ensure that the room temperature is higher

than +5°C and lower than +35°C. Optimal

room temperature is 18°C to 25°C.

Set the Minuterie (Time Drying) or the Très

Sec (Extra Dry) programme.

The display shows .

If you want to set a new programme, deacti‐

vate and activate the appliance.

Make sure that the options are suitable for

the programme.

After maximum 6 hours, the programme ends automatically.

It can happen that some area remains humid when drying big items (e.g. bed sheets ).

If the drying results are not

satisfactory

• The set programme was incorrect.

• The filter is clogged.

• The Heat Exchanger is clogged.

• There was too much laundry in the

appliance.

• The drum is dirty.

• Incorrect setting of the conductivity

sensor ( See chapter "

Settings -

Adjustment of the remaining laundry

moisture degree

" for better setting).

• The airflow slots are clogged.

• Room temperature is too low or too

high ( optimal room temperature 18°C

to 25°C )

TECHNICAL DATA

Height x Width x Depth 850 x 596 x 630 mm (maximal 659 mm)

Max. depth with the appliance door open 1104 mm

Max. width with the appliance door open 958 mm

Adjustable height 850 mm (+ 15 mm - feet regulation)

Drum volume 118 l

Maximum load volume 8 kg

Voltage 220-240 V

Frequency 50 Hz

Sound power level 65 dB

Total power 2800 W

Energy efficiency class B

Energy consumption on the standard cotton

programme with the full load.

4,81 kWh

La page est en cours de chargement...

Arthur_Martin AW6C4824CS Manuel utilisateur

Marque: Arthur_Martin

Modèle: AW6C4824CS

Catégorie: Sèche-linge

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Arthur_Martin AW6C4824CS User manual

Arthur_Martin AW6C4824CS Manuel utilisateur

Arthur_Martin AW6C4824CS Manuel utilisateur

dans d''autres langues

Autres documents