VTech CS6759 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
1
CS6509/CS6509-14/
CS6509-15/CS6509-16/
CS6509-17/CS6509-19
DECT 6.0 accessory handset
for use with VTech models
CS6519/CS6529
User’s manual
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 5 of this manual.
This manual has instructions on how to set up and register your new handset.
For complete instructions on using the handset, see the Abridged users manual
that came with your telephone base.
Please refer to the Users manual for a full set of installation and operation
instructions at www.vtechphones.com.
The ENERGY STAR
®
program (www.energystar.gov) recognizes
and encourages the use of products that save energy and help
protect our environment. We are proud to mark this product with
the ENERGY STAR
®
label indicating it meets the latest energy
efficiency guidelines.
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced warranty support.
Product news
Learn about the latest VTech products.
BC
T
Compatible with
Hearing Aid T-Coil
TIA-1083
2
Battery installation
Install the battery as shown below.
Plug the battery connector
securely into the socket.
1.
Place the battery with the label
THIS SIDE UP facing up and
the wires inside the battery
compartment.
2.
Slide the battery compartment cover
towards the center of the handset
until it clicks into place.
3. Place the handset in the telephone
base or charger to charge.
4.
CHARGE
light remains
on when
charging.
If the handset will not be used for a long time, disconnect and remove the battery
to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial
1 (800) 267-7377.
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Battery
Battery compartment
cover
Charger and
charger adapter
Handset
User’s manual
User’s manual
3
Add and register a handset
You can add new handsets (CS6509/CS6509-14/CS6509-15/CS6509-16/
CS6509-17/CS6509-19, purchased separately) to your telephone system. Each
handset must be registered with the telephone base before use. When first
purchased, each expansion handset displays To register HS and See manual
alternately. You may need to charge the handset before registering it to the
telephone base.
To register a handset:
Place the new (non-registered) handset in the telephone base.
2. After about 10 seconds, the handset displays Registering... When the
registration process completes, the handset displays Registered and you
hear a beep. The registration process takes about 90 seconds to complete.
Deregister handsets
If you want to replace a handset or reassign the designated handset number of
a registered handset, you must deregister all the handsets and then individually
register each handset.
To deregister all handsets:
Press and hold FIND HANDSET on the telephone base for about 10 seconds
until the IN USE light on the telephone base turns on and starts to flash.
Immediately press FIND HANDSET again. You must press FIND HANDSET
while the IN USE light is still flashing. The IN USE light ashes for approximately
five seconds.
All handsets display To register HS and See manual alternately when the
deregistration process completes. The deregistration process takes about
10 seconds to complete.
1.
1.
2.
3.
CS6519 base CS6529 base
Do not place the handset
in the charger.
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below).
Battery indicators Battery status Action
The screen is blank, or
displays Put in charger
and flashes.
The battery has no or very little
charge. The handset cannot
be used.
Charge without interruption
(at least 30 minutes).
The screen displays
Low battery and flashes.
The battery has enough charge
to be used for a short time.
Charge without interruption
(about 30 minutes).
The screen displays
HANDSET X.
The battery is charged. To keep the battery charged,
place it in the telephone
base or charger when not
in use.
For best performance, keep the handset in the telephone base or charger when
not in use.
The battery is fully charged after 11 hours of continuous charging.
If you place the handset in the telephone base or the charger without plugging
in the battery, the screen displays NO BATTERY.
When the battery is fully charged, you can expect the following performance:
Operation Operating time
While in handset use (talking*) Up to 7 hours
While in speakerphone mode (talking*) Up to 3.5 hours
While not in use (standby**) Up to 5 days
*Operating times vary depending on your actual use and the age of the battery.
**Handset is not charging or in use.
4
Handset overview
CID/ /VOLUME
Review the caller ID log when
the
phone is not in use.
Decrease the listening volume
during a call.
Decrease the listening volume
during message playback (for
CS6529 only).
Scroll down while in a menu,
or in the directory, caller ID log
or redial list.
Move the cursor to the left
when entering numbers or
names.
CHARGE light
On when the handset is
charging.
/ /VOLUME
Review the directory when the
phone is not in use.
Increase the listening volume
during a call.
Increase the listening volume
during message playback (for
CS6529 only).
Scroll up while in a menu, or
in the directory, caller ID log or
redial list.
Move the cursor to the right
when entering numbers or
names.
MUTE/DELETE
Mute the microphone during
a call.
Delete digits or characters
while using the dialling keys.
Silence the ringer temporarily
while the handset is ringing.
Delete the displayed entry
while in the directory, caller ID
log or redial list.
MENU/SELECT
Show the menu.
While in a menu, press to
select an item, or save an
entry or setting.
OFF/CANCEL
Hang up a call.
Silence the ringer temporarily
while the handset is ringing.
Press and hold to erase the
missed call indicator while the
phone is not in use.
Press to return to the previous
menu, or press and hold to
return to idle mode, without
making changes.
QUIET#
Press and hold to set and turn
on the quiet mode, or turn it off.
Press repeatedly to show other
dialing options when reviewing a
caller ID log entry.
INT
Start an intercom conversation
or transfer a call (for
multi-handset models only).
/FLASH
Make or answer a call.
Answer another incoming call
during a call.
REDIAL/PAUSE
Press repeatedly to review the
redial list.
Press and hold to insert a
dialing pause while dialing or
entering a number.
Dialing keys
Enter numbers or characters.
Answer an incoming call.
TONE
Switch to tone dialing
temporarily during a call.
Make or answer a call using the
handset speakerphone.
During a call, press to switch
between the speakerphone and
the handset.
1
Press repeatedly to add or
remove 1 in front of the caller
ID log entry before dialing or
saving it to the directory.
Press and hold to set or dial
your voicemail number.
5
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury, including the following:
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a
swimming pool, or in a wet basement or shower.
Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.
This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply in your home or office, consult your dealer or local
power company.
Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service
facility. Opening or removing parts of the telephone base or handset other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.
Do not overload wall outlets and extension cords.
Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled onto the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the
product to normal operation.
If the product has been dropped and the telephone base and/or handset has been damaged.
If the product exhibits a distinct change in performance.
Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric
shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a
spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced
in its cradle. This is a common event associated with the closing of any electrical circuit. The user should
not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the
phone is located in an environment containing concentrations of flammable or flame-supporting gases,
unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.
Such environments might include: medical use of oxygen without adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
Only put the handset of your telephone next to your ear when it is in normal talk mode.
The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are
not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
Battery
CAUTION: Use Only Supplied Battery.
Do not dispose of the battery in a fire. Check with local waste management codes for special disposal
instructions.
Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the
eyes or skin. The electrolyte may be toxic if swallowed.
Exercise care in handling batteries in order not to create a short circuit with conductive materials.
Charge the battery provided with or identified for use with this product only in accordance with the
instructions and limitations specified in this manual.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation
of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless telephones at least six inches from the pacemaker.
Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it
is turned ON.
Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless
telephones.
About cordless telephones
Privacy: The same features that make a cordless telephone convenient create some limitations.
Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason, you should not think of
cordless telephone conversations as being as private as those on corded telephones.
Electrical power: The telephone base of this cordless telephone must be connected to a working
electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power
is interrupted.
Potential TV interference: Some cordless telephones operate at frequencies that may cause
interference to televisions and VCRs. To minimize or prevent such interference, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,
moving the cordless telephone farther away from the TV or VCR often reduces or eliminates
the interference.
Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between the battery and the battery charger.
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not
burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
6
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance
- which can vary with the locations of the telephone base and handset, the weather, and the layout of your
home or office.
When the handset is out of range, the handset displays Out of range or no pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well
when you press . Move closer to the telephone base, then press to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
ECO mode
This power conserving technology reduces power consumption for optimal battery performance. The ECO
mode activates automatically whenever the handset is synchronized with the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need
to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
The RBRC
®
seal
The RBRC
®
seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The RBRC
®
program provides a convenient alternative to placing used nickel-metal hydride batteries into the
trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC
®
makes it easy for you to drop off the spent battery at local retailers participating
in the RBRC
®
program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY
TM
for
information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this
program is part of its commitment to protecting our environment and conserving natural resources.
RBRC
®
is a registered trademark of Rechargeable Battery Recycling Corporation.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in
water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE
POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the
unplugged cords.
7
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of communications may not be ensured
when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the
user. The telephone base shall be installed and used such that parts of the user’s body other than the hands
are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be
provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before interrupting
service. If advance notice is not practical, you will be notified as soon as possible. You will be given the
opportunity to correct the problem and the telephone service provider is required to inform you of your right to
file a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper functioning of this product. The telephone service
provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Privacy of communications may not be ensured when using this phone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of
the maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the RENs
of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
California Energy Commission battery charging testing
instructions
This telephone is set up to comply with the energy-conserving standards right out of the box. These
instructions are intended for California Energy Commission (CEC) compliance testing only. When the
CEC battery charging testing mode is activated, all telephone functions, except battery charging, will be
disabled.
To activate the CEC battery charging testing mode:
Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged
with charged batteries.
While you press and hold FIND HANDSET, plug the telephone base power adapter back to the
power outlet.
After about 20 seconds, when the IN USE light starts flashing, release FIND HANDSET and then
press it again within 2 seconds.
When the phone successfully enters the CEC battery charging testing mode, the IN USE light
turns off and all handsets display To register HS and See manual alternately.
When the phone fails to enter this mode, repeat Step 1 through Step 3 above.
Note: The telephone base will be powered up as normal if you fail to press FIND HANDSET within
2 seconds in Step 3.
To deactivate the CEC battery charging testing mode:
Unplug the telephone base adapter from the power outlet, then plug it back in. Then the telephone base
is powered up as normal.
Register your handsets back to the telephone base. See page 3 for handset registration instructions.
1.
2.
3.
1.
2.
8
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez votre téléphone :
Lisez et comprenez bien toutes les instructions.
Observez toutes les instructions et mises en garde inscrites sur l’appareil.
Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni
en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac
de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.
Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et
être sérieusement endommagé.
Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Afin
d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan,
tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une
plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas
d’aération adéquate.
Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil.
Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur
d’électricité.
Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où
personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.
N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à
des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou
d’électrocution. N’échappez pas de liquides dans l’appareil.
Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un
centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des
tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.
Ne surchargez pas les prises de courant et les rallonges.
Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la
clientèle de VTech dans les cas suivants:
Lorsque le cordon d’alimentation est endommagé ou écorché.
Si du liquide a été échappé dans l’appareil.
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez
uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages
incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail
exhaustif de la part d’un technicien autorisé afin de rétablir le fonctionnement normal de l’appareil.
Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
Si le produit affiche une nette diminution de sa performance.
Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à l’origine
d’une électrocution.
N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise de
courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé à la
fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant,
et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un
endroit comportant des concentrations de gaz inflammables, à moins que la ventilation soit adéquate. Une
flammèche dans un tel endroit pourrait provoquer un incendie ou une explosion. De tels environnements
peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.
Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.
Ces adaptateurs ont été cous pour être oriens en position verticale ou montés au sol. Les broches ne sont
pas coues pour maintenir l’adaptateur en place si celui-ci est barnc dans une prise au plafond ou sous
une table/ armoire.
CONSERVEZ CES INSTRUCTIONS
Pile
MISE EN GARDE : N’utilisez que la pile incluse.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des autorités
locales.
N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des
brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des
matériaux conducteurs. .
Rechargez la pile incluse ou identifiée pour fonctionner avec cet appareil, selon les instructions et limites
spécifiées dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené
une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une
poche de chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée
au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
9
For C-UL compliance only
À propos des téléphones sans l
Condentialité : Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans
fil afchent également des restrictions. Les appels téphoniques sont transmis entre le combiné sans
fil et le socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations téphoniques
sans fil soient interceptées par des équipements de réception radio se trouvant dans la portée du
combiné sans fil. Pour cette raison, vous ne devez pas percevoir les communications téphoniques
sans fil comme étant aussi confidentielles que celles des téphones à cordons.
Alimentation électrique : Le socle de ce téphone sans fil doit être branché à une prise électrique
fonctionnelle. La prise électrique ne doit pas être contlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si le socle est débranché ou mis hors tension ou si le
courant est coupé.
Possibilité d’interférences aux téviseurs : Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interrences aux téléviseurs et aux magnétoscopes. Pour réduire ou
prévenir de telles interférences, ne placez pas le socle du téphone sans fil près ou sur un téléviseur
ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner le téphone sans fil du
téléviseur ou du magnétoscope afin de réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec des
bagues, bracelets ou cs. Les piles ou le conducteur peut surchauffer et causer des blessures.
Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de manière
écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce
type, elles pourraient dégager une matière toxique qui peut causer des blessures corporelles si elles
sont brûlées ou peres.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in
material and workmanship, pursuant to the following terms and conditions, when installed and used normally
and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer
for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date
the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year
warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure
is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty,
VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.
You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by
this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along
with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
10
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
Technical specications
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Handset: 1921.536-1928.448 MHz
Channels 5
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary
according to environmental conditions at the time of use.
Power requirements Handset: 2.4V Ni-MH battery
Charger: 6V AC @ 300mA
Memory Handset directory:
50 memory locations; up to 30 digits and 15 characters
Handset caller ID log:
50 memory locations; up to 24 digits and 15 characters
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is a registered trademark of VTech Holdings Limited.
Specifications are subject to change without notice.
© 2014 for VTech Communications, Inc.
All right reserved. 05/14. CS6509-X_CIB_V2.0
Document order number: 91-007223-020-100
Designed to fit your home.
And your life.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

VTech CS6759 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

dans d''autres langues