LG DLEX2801R Le manuel du propriétaire

Protocol P154

Sanitization Performance of Residential

Clothes dryer

Ejecucion de Saneamiento en la zona

residencial Secadoras

Niveau de sanitisation des séche-linge

résidentiels

P/No. 3828EL3010T

Before beginning installation, read these

instructions carefully. This will simplify installation

and ensure that the dryer is installed correctly and

safely. Leave these instructions near the dryer

after installation for future reference.

Antes de comenzar la instalación, lea atentamente

estas instrucciones. Esto simpliﬁcará la instalación

y asegurará que la secadora está instalada

en forma correcta y segura. Conserve estas

instrucciones cerca de la secadora luego de la

instalación para futuras consultas.

To contact LG Electronics, 24 hours a day,

7 days a week:

1-800-243-0000

Or visit us on the Web at: us.lge.com

Número telefónico de LG Electronics, las 24

horas del día, 7 días a la semana:

1-800-243-0000

O visítenos en la Web en: us.lge.com

To contact LG Electronics, 24 hours a day,

7 days a week :

1-888-LGCANADA

Or visit us on the Web at : ca.lge.com

Pour contacter LG Electronics, 24 heures

Par jour, 7 jours par semaine :

1-888-LGCANADA

Ou visitez notre site Web a l’addresse :

ca.lge.com

C

E

R

T

I

F

I

E

D

E

S

I

G

N

DLEX2801W

DLEX2801R

DLEX2801L

DLGX2802W

DLGX2802R

DLGX2802L

Avant de commencer à installer votre sécheuse, lisez

attentivement ces instructions. Cela simpliﬁera votre

installation et assurera que la sécheuse est installée

correctement et en toute sécurité. Conservez ces

instructions à proximité de la sécheuse après son

installation, pour référence future.

Congratulations on your purchase

and welcome to the LG family. Your

new LG Dryer combines the most

advanced drying sensor technology

with simple operation and high

efficiency. By following the

operating and care instructions

in this manual, your dryer will

provide you with many years of

reliable service.

THANK YOU!

INSTALLATION INSTRUCTIONS

IMPORTANT: Read all installation instructions

completely before installing and operating your

dryer! ................................................................... 10

Choose the Proper Location ................................ 10

Clearances ........................................................... 10

Installation With Optional

Pedestal Base or Stacking Kit .............................. 11

Optional Accessories ......................................... 11

Leveling the Dryer ................................................ 12

Reversing the Door Swing .................................... 12

Changing the Dryer Vent Location ....................... 13

Venting the Dryer ............................................ 14, 15

Connecting Gas Dryers .................................. 16, 17

Connecting Electric Dryers ............................. 18–22

Special Requirements for Manufactured

or Mobile Homes .................................................. 23

Final Installation Check ....................................... 23

Flow Check (Duct condition test) ......................... 24

HOW TO USE

Sorting Loads ....................................................... 2 5

Loading the Dryer ................................................. 25

Check the Lint Filter Before Every Load ............... 25

Control Panel Features ......................................... 26

Cycle Guide .......................................................... 27

The Display ........................................................... 28

Operating the Dryer .............................................. 29

Cycle Setting Buttons .......................................... 29

Cycle Option Buttons .......................................... 30

Special Functions ................................................. 31

Custom Program .................................................. 32

Steam Functions ............................................ 32–34

Steam Cycle Guide .............................................. 34

TROUBLESHOOTING

Before Calling for Service ............................... 36–38

USER MAINTENANCE INSTRUCTIONS

Regular Cleaning .................................................. 35

IMPORTANT SAFETY INSTRUCTIONS

Basic Safety Precautions ....................................... 3

What to Do if You Smell Gas .................................. 4

California safe drinking water and toxic

enforcement act .................................................... 4

Grounding Instructions ...........................................5

Safety Instructions for Installation ......................5, 6

Safety Instructions for Steam Functions ................6

Safety Instructions for Connecting Electricity .......7

PARTS AND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

OPTIONAL ACCESSORIES

Optional Accessories ........................................... 39

Pedestal Installation ....................................... 40, 41

Stacking Kit Installation .................................. 42, 43

Key Dimensions and Speciﬁ cations ..................... 43

WARRANTY ............................................. 44, 45

2

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read

and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

BASIC SAFETY PRECAUTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Readallinstructionsbeforeusingthedryer.

•Beforeuse,thedryermustbeproperlyinstalled

as described in this manual.

•Donotplaceitemsexposedtocookingoilsin

your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that

could cause a load to catch ﬁre.

•Donotdryarticlesthathavebeenpreviously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they give

off vapors that could ignite or explode.

•Donotreachintothedryerifthedrumorany

other part is moving.

•Donotrepairorreplaceanypartofthedryer

or attempt any servicing unless speciﬁcally

recommended in this Use and Care Guide or

in published user-repair instructions that you

understand and have the skills to carry out.

•Donottamperwithcontrols.

•Beforethedryerisremovedfromserviceor

discarded, remove the door to the drying

compartment.

•Donotallowchildrentoplayonorinthedryer.

Close supervision of children is necessary when

the dryer is used near children.

•Donotusefabricsoftenersorproductsto

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

•Donotuseheattodryarticlescontaining

foam rubber or similarly textured rubber-like

materials.

•Keepareaaroundtheexhaustopeningand

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

•Theinteriorofthedryerandexhaustvent

should be cleaned periodically by qualiﬁed

service personnel.

•Donotinstallorstorethedryerwhereitwillbe

exposed to the weather.

•Alwayschecktheinsideofthedryerforforeign

objects.

•Cleanlintscreenbeforeoraftereachload.

3

READ ALL INSTRUCTIONS BEFORE USE

wWARNING

For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

• Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this appliance or any other

appliances.

• Installation and service must be

performed by a qualiﬁ ed installer,

service agency, or the gas supplier.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING

For your safety, the information in this manual must be

followed to minimize the risk of ﬁ re or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

1. Do not try to light a match or cigarette,

or turn on any gas or electrical

appliance.

2. Do not touch any electrical switches.

Do not use any phone in your building.

3. Clear the room, building, or area of all

occupants.

4. Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

5. If you cannot reach your gas

supplier, call the ﬁ re department.

WHAT TO DO IF YOU SMELL GAS:

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a list of substances known to the state to cause

cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential

exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

4

GROUNDING INSTRUCTIONS

5

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing

a path of least resistance for electric current.

This appliance must be equipped with a cord

having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

wWARNING — Improper

connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or service

person if you are in doubt as to whether the

appliance is properly grounded.

Do not modify the plug provided with the

appliance. If it will not ﬁt the outlet, have a proper

outlet installed by a qualiﬁed electrician.

This appliance must be connected to a grounded

metal, permanent wiring system or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Electrical shock can result if the dryer is not

properly grounded.

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

•Properly ground dryer to conform with all

governing codes and ordinances. Follow

details in the installation instructions. Electrical

shock can result if the dryer is not properly

grounded.

•Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not

properly grounded.

•Install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

•All repairs and servicing must be performed

by an authorized servicer unless speciﬁcally

recommended in this Owner’s Guide. Use

only authorized factory parts. Failure to follow

this warning can cause serious injury, ﬁre,

electrical shock, or death.

•To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning can cause serious injury, ﬁre,

electrical shock, or death.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Connect to a properly rated, protected,

and sized power circuit to avoid electrical

overload. Improper power circuit can melt,

creating electrical shock and/or ﬁre hazard.

•Remove all packing items and dispose of all

shipping materials properly. Failure to do so

can result in death, explosion, ﬁre, or burns.

•Place dryer at least 18 in. above the ﬂoor

for a garage installation. Failure to do so can

result in death, explosion, ﬁre, or burns.

•Keep all packaging from children. Packaging

material can be dangerous for children. There is

a risk of suffocation.

•Do not install nearby heat item. Such as

stove, cooking oven. Failure to do so can cause

deform, smoke and ﬁre.

•Do not place candle and cigarettes on top of

the product. Failure to do so can cause deform,

smoke and ﬁre.

•Remove all protective vinyl ﬁlm from the

product. Failure to do so can cause deform,

smoke and ﬁre.

6

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁ re or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

Exhaust/Ducting:

•Gas dryers MUST be exhausted to the

outside. Failure to follow these instructions

can result in ﬁ re or death.

•The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is

not exhausted outdoors, some ﬁ ne lint and

large amounts of moisture will be expelled

into the laundry area. An accumulation of

lint in any area of the home can create a health

and ﬁ re hazard.

•Use only rigid metal or ﬂ exible metal 4-in.

diameter ductwork inside the dryer cabinet

or for exhausting to the outside. Use of

plastic or other combustible ductwork can

cause a ﬁ re. Punctured ductwork can cause

a ﬁ re if it collapses or becomes otherwise

restricted in use or during installation.

•Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the dryer

is not in use. Failure to follow these instructions

can result in ﬁ re or death.

•The exhaust duct must be 4 in. (10.2 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁ re or death.

•Rigid or semi rigid metal ducting is

recommended for use between the

dryer and the wall. In special installations

when it is impossible to make a connection

with the above recommendations, a UL-

listed ﬂ exible metal transition duct may be

used between the dryer and wall connection

only. The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁ re or death.

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁ ciency

of the exhaust system. Secure all joints with

duct tape. For complete details, follow the

Installation Instructions. Failure to follow these

instructions can result in ﬁ re or death.

SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS

•Do not open the dryer door during steam

cycles. Failure to follow these instructions can

result in a burn hazard.

•Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂ ammable or explosive substances as they

give off vapors that could ignite or explode.

Failure to follow these instructions can result in

ﬁ re or death.

•Do not ﬁ ll the steam feeder with gasoline,

dry-cleaning solvents, or other ﬂ ammable or

explosive substances. Failure to follow these

instructions can result in ﬁ re or death.

•Do not touch the steam nozzle in the drum

during or after the steam cycle. Failure to

follow these instructions can result in a burn

hazard.

•Do not ﬁ ll the steam feeder with hot water

(over 86°F/30°C). Failure to follow these

instructions can result in a burn hazard.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

•Do not, under any circumstances, cut or

remove the ground prong from the power

cord. To prevent personal injury or damage to

the dryer, the electrical power cord must be

plugged into a properly grounded outlet.

•For personal safety, this dryer must be

properly grounded. Failure to do so can result

in electrical shock or injury.

•Refer to the installation instructions in this

manual for speciﬁc electrical requirements

for your model. Failure to follow these

instructions can create an electrical shock

hazard and/or a ﬁre hazard.

•This dryer must be plugged into a properly

grounded outlet. Electrical shock can result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualiﬁed

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a

ﬁre hazard.

•The dryer should always be plugged into

its own individual electrical outlet which

has a voltage rating that matches the rating

plate. This provides the best performance

and also prevents overloading house wiring

circuits which could cause a ﬁre hazard from

overheated wires.

•Never unplug your dryer by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet. The power cord

can be damaged, resulting in a risk of ﬁre and

electrical shock.

•Repair or replace immediately all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows

cracks or abrasion damage along its length

or at either end. The power cord can melt,

creating electrical shock and/or ﬁre hazard.

•When installing or moving the dryer, be

careful not to pinch, crush, or damage

the power cord. This will prevent injury and

prevent damage to the dryer from ﬁre and

electrical shock.

SAVE THESE INSTRUCTIONS

7

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USE

wWARNING

For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

SPECIAL FEATURES

4

1

2

1

EASY-TO-USE CONTROL PANEL

Rotate the Cycle Selector Knob to select the

desired dry cycle. Add cycle options or adjust

settings with the touch of a button.

2

3

4

EASY-ACCESS REVERSIBLE DOOR

Wide-opening door provides easy access for

loading and unloading. Door swing can be

reversed to adjust for installation location.

ULTRA-CAPACITY STAINLESS STEEL DRUM

WITH DRUM LIGHT

The ultra-large stainless steel drum offers

superior durability. The drum is equipped with a

yellow light that illuminates when the dryer door

is open and turns off when the door is closed.

3

HELPFUL STEAM FUNCTIONS

LG’s new steam technology allows you to inject

fabrics with a swirling jet of hot steam to refresh

clothes, reduce static, and make ironing easier.

Simply select the STEAMFRESH

™

cycle, or you

can add a Steam option to selected cycles.

5

FLOW SENSE™ DUCT BLOCKAGE SENSING

SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing

system detects and alerts you to blockages in

the ductwork that reduce exhaust flow from the

dryer. This improve operating efficiency and help

minimize service calls, saving you money.

8

1

2

LEVELING FEET

Four leveling feet (two in the front, and two in the back)

adjust to improve dryer stability on uneven floors.

2

FRONT-MOUNT LINT FILTER

Front-mounted lint filter allows for easy access

and cleaning after every load.

Terminal Block

Access Panel

(Electric Models)

Rear of Dryer

Power Cord Location

(Gas Models)

Gas

Connection

Location

(Gas Models)

Exhaust Duct

Outlet

KEY PARTS AND COMPONENTS

In addition to the special features and

components outlined in the Special Features

section, there are several other important

components that are referenced in this manual.

DRYING RACK

Use the drying rack with the RACK DRY cycle

option. The drying rack allows items, such as

sweaters, delicates, and gym shoes, to be placed

in a flat position for drying.

3

Included Accessories

Drying Rack

3

1

9

CHOOSE THE PROPER LOCATION

•Storeandinstallthedryerwhereitwillnotbe

exposed to temperatures below freezing or

exposed to outdoor weather conditions.

•Choosealocationwithasolid,levelﬂoor.

•Ifthedryerisbeinginstalledinagarage,

place the dryer at least 18 in. (46 cm) above

the ﬂ oor.

CLEARANCES

(129.7mm)

(56.8 mm)

22.4

•Mostinstallationsrequireaminimum5½in.

(14 cm) clearance behind the dryer for the

exhaust ducting.

•Allowminimumclearancesofatleast1in.

(2.5 cm) on the sides and back to minimize

vibration and noise.

•Allowingadditionalclearanceforinstallationand

servicing is recommended.

•Besuretoallowforwall,door,orﬂoormoldings

that may increase the required clearances.

•Allowatleast24in.(61cm)infrontofthedryer

to open the door.

IMPORTANT: Read all installation instructions completely before

installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions

concerning electrical connections, gas connections, and exhaust requirements are provided on the

following pages.

•Properlygrounddryertoconformwithall

governing codes and ordinances.

•Toreducetheriskofelectricshock,donot

install the dryer in damp or wet locations.

•Ifyouareinstallingyourdryerinamanufactured

or mobile home, please refer to the section

Special Requirements for Manufactured or

Mobile Homes.

Additional Instructions for closet installations:

•Theclosetdoormustallowforsufcientairﬂow.

Refer to the diagram above for minimum vent

opening requirements. A louvered door is also

acceptable.

•Makesurethatthereisatleast18in.(46cm)of

clearance above the dryer.

Closet Door Vent

Requirements

10

INSTALLATION WITH OPTIONAL

PEDESTAL BASE OR STACKING KIT

IMPORTANT: If you are installing your dryer

using an optional pedestal base or stacking

kit, please refer to Optional Accessories in this

manual or to the instructions for your pedestal

or stacking kit before proceeding with the

installation.

Required Dimensions for Installation

With Pedestal

Required Dimensions for Installation

With Stacking Kit

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at us.lge.com.

Pedestal (sold separately)

Stacking Kit (sold separately)

11

1 2

Hinge

Screws

Door

Latch

Latch Screws

Hinge

Screws

Latch

Screws

LEVELING THE DRYER

Use an adjustable wrench to turn the leveling

feet. Turn clockwise to raise the dryer or

counterclockwise to lower it. Raise or lower

the leveling feet until dryer is level from

side to side and front to back.

Make sure that all 4 leveling feet are in firm

contact with the floor.

REVERSING THE DOOR SWING

The swing of the dryer door can be reversed to fit your installation location.

Open the dryer door. Using a Phillips

screwdriver, remove the 4 screws that secure

the door hinge to the dryer door opening.

Remove the 6 screws from the latch side of the

dryer door opening, and remove the door latch.

Turn the door around so the hinge is

reversed, and reattach the door using the

4 screws previously removed. Reinstall the

door latch and the 6 screws.

Test the door swing to make sure the door

moves freely and latches securely.

2

Position the dryer in the final location. Place

a level across the top of the dryer.

1

Level

Leveling Feet

•All four levelingfeetmustrest solidly onthe

floor. Gently push on the top corners of the

dryer to make sure that the dryer does not

rock from corner to corner.

If you are installing the dryer on the optional

pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet

should be fully retracted.

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as

necessary to level the dryer. Extending the

leveling feet more than necessary can cause

the dryer to vibrate.

12

WARNING

•Wearglovesduringinstallation.

•Failuretofollowtheseinstructionscanresultininjury.

w

CHANGING THE DRYER VENT LOCATION

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom

or side (right-side venting is not available on

gas models).

An adapter kit, part number 383EEL9001B,

may be purchased from your LG retailer. This

kit contains the necessary duct components

to change the dryer vent location.

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

1

Rear

Exhaust Duct

Retaining

Screw

Preassemble a 4-in. (10.2 cm) elbow to the next 4-in.

(10.2 cm) duct section, and secure all joints with duct tape.

Be sure that the male end of the elbow faces AWAY from

the dryer.

Insert the elbow/duct assembly through the side opening

and press it onto the adapter duct. Secure in place with

duct tape.

Besurethatthemaleendoftheductprotrudes1½in.(3.8

cm) to connect the remaining ductwork.

Attach cover plate to the back of the dryer with included

screw.

1

/2"

(3.8 cm)

3

Elbow

Cover

Plate

Insert the 4-in. (10.2 cm) elbow through the

rear opening and press it onto the adapter

duct. Be sure that the male end of the elbow

faces down through hole in the bottom of the

dryer. Secure in place with duct tape.

Attach the cover plate to the back of the

dryer with included screw.

3

Elbow

Cover

Plate

Press the tabs on the knockout and carefully remove the

knockout for the desired vent opening (right-side venting

is not available on gas models). Press the adapter duct

onto the blower housing and secure to the base of the

dryer as shown.

2

Knockout

Bracket

Adapter

Duct

OPTION 1: Side Venting

Press the adapter duct onto the blower

housing and secure to the base of the dryer

as shown.

2

Bracket

Adapter

Duct

OPTION 2: Bottom Venting

13

WARNING

w

•Useaheavymetalvent.

•Donotuseplasticorthinfoilduct.

•Cleanoldductsbeforeinstallingthisdryer.

•Wearglovesduringinstallation.

•Failuretofollowtheseinstructionscanresultindeath

or ﬁre.

VENTING THE DRYER

•Do not crush or collapse ductwork. Failure

to follow these instructions can result in ﬁ re

or death.

•Do not allow ductwork to rest on or

contact sharp objects. Failure to follow these

instructions can result in ﬁ re or death.

•If connecting to existing ductwork, make

sure it is suitable and clean before installing

the dryer. Failure to follow these instructions

can result in ﬁ re or death.

•Venting must conform to local building

codes. Failure to follow these instructions can

result in ﬁ re or death.

•Gas dryers MUST exhaust to the outdoors.

Failure to follow these instructions can result

in ﬁ re or death.

•Use only 4-in. (10.2 cm) rigid or ﬂ exible

metal ductwork inside the dryer cabinet and

for venting outside. Failure to follow these

instructions can result in ﬁ re or death.

•To reduce the risk of ﬁ re, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall,

ceiling, crawl space, chimney, gas vent, or

concealed space of a building. Failure to

follow these instructions can result in ﬁ re

or death.

•To reduce the risk of ﬁ re, DO NOT exhaust

the dryer with plastic or thin foil ducting.

Failure to follow these instructions can result

in ﬁ re or death.

•In Canada, that the exhaust duct shall

be 4in.(10.2 cm) in diameter with no

obstructions. In the United States. the

required exhaust duct diameter; The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁ re or death.

•Rigid or semirigid metal ducting is

recommended for use between the dryer

and the wall. In special installations when

it is impossible to make a connection with

the above recommendations, a UL-listed

ﬂ exible metal transition duct may be used

between the dryer and wall connection only.

The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁ re or death.

•In Canada. that only those foil-type ﬂ exible

ducts, if any, speciﬁ cally identiﬁ ed for use

with the appliance by the manufacturer shall

be used. In the United States, that only those

foil-type ﬂ exible ducts, if any, speciﬁ cally

identiﬁ ed for use with the appliance by the

manufacturer and that comply with the

Outline for Clothes Dryer Transition Duct,

Subject 2158A, shall be used

•DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁ ciency

of the exhaust system. Secure all joints

with duct tape. Failure to follow these

instructions can result in ﬁ re or death.

•To maximize operating results, please

observe the duct length limitations noted in

the chart on page 15. Failure to follow these

instructions can result in ﬁ re or death.

•Ductwork is not provided with the dryer.

You should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the

dryer is not in use. Failure to follow these

instructions can result in ﬁ re or death.

•The Total length of ﬂ exible metal duct shall

not exceed 8 ft.(2.4m)

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

14

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included

and must be purchased separately.

•Use4-in.(10.2cm)diameterrigidorsemirigid

metal ductwork.

•Theexhaustductrunshouldbeasshortas

possible.

•Useasfewelbowjointsaspossible.

•Themaleendofeachsectionofexhaustduct

must point away from the dryer.

•Useducttapeonallductjoints.

•Insulateductworkthatrunsthroughunheated

areas in order to reduce condensation and lint

buildup on duct surfaces.

IMPORTANT: Failure to exhaust the dryer

correctly will void the dryer’s warranty.

VENTING THE DRYER (cont.)

Correct Venting

Incorrect Venting

Number of Max. Length of 4-In. Dia.

Wall Cap Type 90° Elbows Rigid Metal Duct

0 65 ft. (19.8 m)

1 55 ft. (16.8 m)

2 47 ft. (13.7 m)

3 36 ft. (11.0 m)

4 28 ft. (8.5 m)

0 55 ft. (16.8 m)

1 47 ft. (13.7 m)

2 41 ft. (12.5 m)

3 30 ft. (9.1 m)

4 22 ft. (6.7 m)

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.

4"

(10.2 cm)

2

1

/2"

(6.35 cm)

4"

(10.2 cm)

Recommended

Use Only for Short

Run Installations

Ductwork

15

Electrical Requirements for Gas Models Only

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power

cord. Failure to follow this warning can result in

ﬁ re, explosion, or death.

• For personal safety, this dryer must be properly

grounded. Failure to follow this warning can result

in ﬁ re, explosion, or death.

• The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock

hazard from this appliance. Failure to follow this

warning can result in ﬁ re, explosion, or death.

• This dryer must be plugged into a

120-VAC, 60-Hz. grounded outlet protected by

a 15-ampere fuse or circuit breaker. Failure to

follow this warning can result in ﬁ re, explosion,

or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet. Failure

to follow this warning can result in ﬁ re, explosion,

or death.

16

CONNECTING GAS DRYERS

•Gas supply requirements:

As shipped from the factory, this dryer is

con gured for use with natural gas. It can be

converted for use with LP (Liqueﬁ ed Propane)

gas. Gas pressure must not exceed 13 in.

water column.

•A qualiﬁ ed service or gas company technician

must connect the dryer to the gas service.

Failure to do so can result in ﬁ re, explosion,

or death.

•Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve

during any pressure testing of the gas supply.

Failure to do so can result in ﬁ re, explosion,

or death.

•Supply line requirements:

Your laundry room must have a rigid gas

supply line to your dryer. In the United States,

an individual manual shutoff valve MUST be

installed within at least 6 ft. (1.8 m) of the dryer,

in accordance with the National Fuel Gas Code

ANSI Z223.1 or Canadian gas installation code

CSA B149.1. A 1/8-in. NPT pipe plug must

be installed. Failure to do so can result in ﬁ re,

explosion, or death.

•If using a rigid pipe, the rigid pipe should be

1/2-in. IPS. If acceptable under local codes

and ordinances and when acceptable to your

gas supplier, 3/8-in. approved tubing may be

used where lengths are less than 20 ft. (6.1

m). Larger tubing should be used for lengths

in excess of 20 ft. (6.1 m). Failure to do so can

result in ﬁ re, explosion, or death.

•Connect the dryer to the type of gas shown on

the nameplate. Failure to do so can result in ﬁ re,

explosion, or death.

•To prevent contamination of the gas valve,

purge the gas supply of air and sediment

before connecting the gas supply to the dryer.

Before tightening the connection between the

gas supply and the dryer, purge remaining air

until the odor of gas is detected. Failure to do

so can result in ﬁ re, explosion, or death.

•DO NOT use an open ﬂ ame to inspect for gas

leaks. Use a noncorrosive leak-detection ﬂ uid.

Failure to do so can result in ﬁ re, explosion, or

death.

•Use only a new AGA- or CSA-certiﬁ ed gas

supply line with ﬂ exible stainless steel

connectors. Failure to do so can result in ﬁ re,

explosion, or death.

•Securely tighten all gas connections. Failure

to do so can result in ﬁ re, explosion, or death.

•Use Teﬂ on

®

tape or a pipe-joint compound that

is insoluble in Liqueﬁ ed Petroleum (LP) gas on

all pipe threads. Failure to do so can result in ﬁ re,

explosion, or death.

•DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and

tools of an authorized and qualiﬁ ed service

person or company. Failure to do so can result

in ﬁ re, explosion, or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Installation and service must be performed

by a qualiﬁed installer, service agency, or the

gas supplier. Failure to do so can result in ﬁre,

explosion, or death.

•Use only a new stainless steel ﬂexible

connector and a new AGA-certiﬁed

connector. Failure to do so can result in ﬁre,

explosion, or death.

•A gas shutoff valve must be installed within

6 ft. (1.8 m) of the dryer. Failure to do so can

result in ﬁre, explosion, or death.

•The dryer is conﬁgured for Natural Gas when

shipped from the factory. Make sure that the

dryer is equipped with the correct burner

nozzle for the type of gas being used (Natural

Gas or Liqueﬁed Petroleum). Failure to do so

can result in ﬁre, explosion, or death.

•If necessary, the correct nozzle (for the LP

nozzle kit order part number 4948EL4002B)

should be installed by a qualiﬁed technician

and the change should be noted on the dryer.

Failure to do so can result in ﬁre, explosion,

or death.

•All connections must be in accordance with

local codes and regulations. Failure to do so

can result in ﬁre, explosion, or death.

•Gas dryers MUST exhaust to the outdoors.

Failure to do so can result in ﬁre, explosion,

or death.

3/8" NPT Gas

Connection

Gas Supply

Shutoff Valve

Connecting the Gas Supply

Make sure that the gas supply to the laundry

room is turned OFF. Confirm that the type

of gas available in your laundry room is

appropriate for the dryer. The dryer is

prepared for Natural Gas with a 3/8-in. NPT

gas connection.

Remove the shipping cap from the gas

connection at the back of the dryer. Be

careful not to damage the threads of the gas

connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel

connector with a 3/8-in. NPT fitting.

Securely tighten all connections between the

dryer and your laundry room’s gas supply.

Turn on your laundry room’s gas supply and

check all pipe connections (both internal and

external) for gas leaks with a noncorrosive

leak-detection fluid.

1

2

3

4

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for

elevations below 10,000 feet.

If your gas dryer is being installed at an elevation

above 10,000 feet, it must be derated by a

qualified technician or gas supplier.

Electrical Connection

Plug dryer into a

120-VAC, 60-Hz.

grounded 3-prong

outlet.

CONNECTING GAS DRYERS (cont.)

1/8" NPT Pipe

Plug

AGA/CSA-Certified

Stainless Steel

Flexible Connector

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

17

18

Electrical Requirements for Electric Models Only

•This dryer must be connected to a grounded

metal, permanent wiring system, or an

equipment-grounding conductor must

be run with the circuit conductors and

connected to the equipment-grounding

terminal or lead on the dryer. Failure to do

so can result in ﬁ re, explosion, or death.

•The dryer has its own terminal block that

must be connected to a separate 240 VAC,

60-Hertz, single-phase circuit, fused at 30

amperes (the circuit must be fused on both

sides of the line). ELECTRICAL SERVICE

FOR THE DRYER SHOULD BE OF THE

MAXIMUM RATE VOLTAGE LISTED ON THE

NAMEPLATE. DO NOT CONNECT DRYER TO

110-, 115-, OR 120-VOLT CIRCUIT. Heating

elements are available for ﬁ eld installation

in dryers which are to be connected to an

electrical service of a different voltage than

that listed on the rating plate. Failure to follow

these instructions can result in ﬁ re, explosion,

or death.

•If branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters

Laboratories) listed No.-10 AWG wire

(copper wire only), or as required by local

codes. If over 15 ft. (4.50 m), use UL-listed

No.-8 AWG wire (copper wire only), or as

required by local codes. Allow sufﬁ cient

slack in wiring so dryer can be moved from

its normal location when necessary. Failure

to do so can result in ﬁ re, explosion, or death.

•The power cord (pigtail) connection between

wall receptacle and dryer terminal block

IS NOT supplied with dryer. Type of pigtail

and gauge of wire must conform to local

codes and with instructions on the following

pages. Failure to follow these instructions can

result in ﬁ re, explosion, or death.

•A 4-wire connection is required for all mobile

and manufactured home installations, as

well as all new construction after January

1, 1996. A 4-wire connection must be used

where local codes do not permit grounding

through the neutral wire. Failure to do so can

result in ﬁ re, explosion, or death.

Special Electrical Requirements for Mobile or Manufactured Homes

•Any installation in a manufactured or mobile

home must comply with the Manufactured

Home Construction and Safety Standards

Title 24 CFR, Part 32-80 or Standard CAN/

CSA0Z240 MH and local codes and ordinances.

•A 4-wire connection is required for all mobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

Failure to do so can result in ﬁ re, explosion,

or death.

CONNECTING ELECTRIC DRYERS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all

applicable local regulations. Please contact a qualified electrician to check your home’s wiring and

fuses to ensure that your home has adequate electrical power to operate the dryer.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING:

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•Donotmodifytheplugandinternalwire

provided with the dryer.

•Thedryershouldbeconnectedto4-holeoutlet.

•Ifitdoesnotttheoutlet,aproperoutletwill

need to be installed by a qualiﬁ ed electrician.

19

Remove the terminal block access cover

on the upper back of the dryer. Install a

UL-listed strain relief into the power cord

through-hole; then thread a UL-listed, 30A,

240V, 4-wire, #10 AWG-minimum copper

conductor power cord through the

strain relief.

1

Transfer the dryer’s ground wire from behind

the green ground screw to the center screw

of the terminal block. Attach the two hot

leads of the power cord to the outer terminal

block screws. Attach the white neutral wire

to the center terminal block screw. Attach the

power cord ground wire to the green ground

screw. TIGHTEN ALL SCREWS SECURELY.

Reinstall the terminal block access cover.

2

UL-Listed

Strain Relief

UL-Listed

4-Wire

Power Cord

Terminal

Block

Ground Screw

Neutral

(White)

Hot

(Black)

Power Cord

Ground Wire

Hot

(Red)

CONNECTING ELECTRIC DRYERS (cont.)

Four-Wire Connection for Electric Dryers: Power Cord

•A4-wireconnectionisrequiredforallmobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

•AUL-listedstrainreliefisrequired.

•Usea30-amp, 240V, UL-listed power cord

with #10 AWG-minimum copper conductor

and closed loop or forked terminals with

upturned ends.

wWARNING:

• Connect the power cord to the terminal block. Each colored wire should be connected

to same color screw. Wire color indicated on manual is connected to the same color

screw in block. Failure to follow these instructions may result in a short or overload.

• Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductor.

USA ONLY

CONNECTING ELECTRIC DRYERS (cont.)

Remove 5 inches (12.7 cm) of the outer

covering from the wire. Remove 5 inches

of insulation from the ground wire. Cut off

approximately 1

1

⁄

2

inches (3.8 cm) from the

other three wires and strip 1 inch (2.5 cm)

insulation from each wire. Bend the ends of

the three shorter wires into a hook shape.

1

Transfer the dryer’s ground wire from behind

the green ground screw to the center screw

of the terminal block. Attach the two hot

leads of the power cable to the outer terminal

block screws. Attach the white neutral wire

to the center terminal block screw. Attach the

power cable ground wire to the green ground

screw. TIGHTEN ALL SCREWS SECURELY.

Reinstall the terminal block access cover.

3

Ground Wire

Ground Screw

Neutral

(White)

Hot

(Black)

Ground Wire

Hot

(Red)

Remove the terminal block access cover

on the upper back of the dryer. Install a

UL-listed strain relief into the power cord

through-hole; then thread the power cable

prepared in Step 1 through the strain relief.

2

UL-Listed

Strain Relief

UL-Listed

4-Wire

Power Cord

Terminal

Block

5"

(12.7 cm)

1" (2.5 cm)

20

Four-Wire Connection for Electric Dryers: Direct Wire

•A4-wireconnectionisrequiredforallmobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

•AUL-listedstrainreliefisrequired.

•UseUL-listed4-wire #10 AWG-minimum

copper conductor cable.

•Allowatleast5ft(1.5m)lengthtoallowfor

removal and reinstallation of the dryer.

wWARNING:

• Connect the power cord to the terminal block. Each colored wire should be connected

to same color screw. Wire color indicated on manual is connected to the same color

screw in block. Failure to follow these instructions may result in a short or overload.

• Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local

codes prohibit grounding through the neutral conductor.

USA ONLY

La page charge ...

LG DLEX2801R Le manuel du propriétaire

Ce manuel convient également à

LG DLEX2801R Le manuel du propriétaire

dans d''autres langues

Documents connexes