MTD 500 Series Manuel utilisateur

Marque: MTD

Modèle: 500 Series

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

Operator’s Manual

FOR CUSTOMER SERVICE 1-800-668-1238

Form No. 769-11740A

(April 28, 2017)

Safe Operation Practices ........................................ 2

Assembly & Set-Up .................................................. 5

Controls & Operation .............................................14

Service .....................................................................18

Troubleshooting .................................................... 22

Parts/Warranty .............. See Separate Supplement

French ..................................................................... 23

Table of Contents

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all

models and the model depicted may differ from yours.

Snow Thrower

2-Stage & 3-Stage

500 & 800 Series - Models with steering trigger controls.

600 Series - Models without steering trigger controls

Important Safe Operation Practices

Training

1. Read, understand, and follow all instructions on the machine and

in the manual(s) before attempting to assemble and operate. Keep

this manual in a safe place for future and regular reference and for

ordering replacement parts.

2. Be familiar with all controls and their proper operation. Know how to

stop the machine and disengage them quickly.

3. Never allow children under 14 years of age to operate this machine.

Children 14 and over should read and understand the instructions

and safe operation practices in this manual and on the machine and

be trained and supervised by an adult.

4. Never allow adults to operate this machine without proper

instruction.

5. Thrown objects can cause serious personal injury. Plan your snow-

throwing pattern to avoid discharge of material toward roads,

bystanders and the like.

6. Keep bystanders, pets and children at least 75 feet from the machine

while it is in operation. Stop machine if anyone enters the area.

7. Exercise caution to avoid slipping or falling, especially when

operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove

all doormats, newspapers, sleds, boards, wires and other foreign objects,

which could be tripped over or thrown by the auger.

1. Always wear safety glasses or eye shields during operation and while

performing an adjustment or repair to protect your eyes. Thrown

objects which ricochet can cause serious injury to the eyes.

2. Do not operate without wearing adequate winter outer garments.

Do not wear jewelry, long scarves or other loose clothing, which

could become entangled in moving parts. Wear footwear which will

improve footing on slippery surfaces.

3. Use a grounded three-wire extension cord and receptacle for all

machines with electric start engines.

4. Adjust auger housing height to clear gravel or crushed rock surfaces.

5. Disengage all control levers before starting the engine.

6. Never attempt to make any adjustments while engine is running,

except where specifically recommended in the operator’s manual.

7. Let engine and machine adjust to outdoor temperature before

starting to clear snow.

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care in handling

gasoline. Gasoline is extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is spilled on yourself or your

clothes which can ignite. Wash your skin and change clothes immediately.

1. Use only an approved gasoline container.

2. Extinguish all cigarettes, cigars, pipes and other sources of ignition.

3. Never fuel machine indoors.

4. Never remove gas cap or add fuel while the engine is hot or running.

5. Allow engine to cool at least two minutes before refueling.

6. Never over fill fuel tank. Fill tank to no more than ½ inch below bottom

of filler neck to provide space for fuel expansion.

7. Replace gasoline cap and tighten securely.

8. If gasoline is spilled, wipe it off the engine and equipment. Move

machine to another area. Wait 5 minutes before starting the engine. If

fuel is spilled on clothing, change clothing immediately.

9. Never store the machine or fuel container inside where there is an

open flame, spark or pilot light (e.g. furnace, water heater, space heater,

clothes dryer etc.).

10. Allow machine to cool at least 5 minutes before storing.

11. Never fill containers inside a vehicle or on a truck or trailer bed with a

plastic liner. Always place containers on the ground away from your

vehicle before filling.

12. If possible, remove gas-powered equipment from the truck or trailer

and refuel it on the ground. If this is not possible, then refuel such

equipment on a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

13. Keep the nozzle in contact with the rim of the fuel tank or container

opening at all times until fueling is complete. Do not use a nozzle lock-

open device.

Operation

1. Do not put hands or feet near rotating parts, in the auger housing or

chute assembly. Contact with the rotating parts can amputate hands

and feet.

2. The auger control lever is a safety device. Never bypass its operation.

Doing so makes the machine unsafe and may cause personal injury.

3. The control levers must operate easily in both directions and

automatically return to the disengaged position when released.

4. Never operate with a missing or damaged chute assembly. Keep all

safety devices in place and working.

WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property

of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with

these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING!

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of

California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the safe operation practices in this manual. As with any type of power

equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers,

hands, toes and feet and throwing foreign objects. Failure to observe the following safety instructions could result in serious injury or death.

Section 1 — important Safe operation practiceS

5. Never run an engine indoors or in a poorly ventilated area. Engine

exhaust contains carbon monoxide, an odorless and deadly gas.

6. Do not operate machine while under the influence of alcohol or

drugs.

7. Muffler and engine become hot and can cause a burn. Do not touch.

Keep children away.

8. Exercise extreme caution when operating on or crossing gravel

surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while operating on

slopes. Do not operate on steep slopes.

10. Plan your snow-throwing pattern to avoid discharge towards

windows, walls, cars etc. Thus, avoiding possible property damage

or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets or allow

anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear snow at

too fast of a rate.

13. Never operate this machine without good visibility or light. Always

be sure of your footing and keep a firm hold on the handles. Walk,

never run.

14. Release auger control lever to disengage power to the auger when

transporting or not clearing snow.

15. Never operate machine at high transport speeds on slippery

surfaces. Look down and behind and use care when backing up.

16. After striking a foreign object or if the machine should start to

vibrate abnormally, stop the engine, disconnect the spark plug wire

and ground it against the engine. Inspect thoroughly for damage.

Repair any damage before starting and operating.

17. Disengage all control levers and stop engine before you leave the

operating position (behind the handles). Wait until the auger comes

to a complete stop before unclogging the chute assembly, making

any adjustments, or inspections.

18. Never put your hand in the discharge or collector openings. Always

use the clean-out tool provided to unclog the discharge opening.

Do not unclog chute assembly while engine is running. Shut off

engine and remain behind handles until all moving parts have

stopped before unclogging.

19. Use only attachments and accessories approved by the

manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20. When starting engine, pull cord slowly until resistance is felt, then

pull rapidly. Rapid retraction of starter cord (kickback) will pull hand

and arm toward engine faster than you can let go. Broken bones,

fractures, bruises or sprains could result.

21. If situations occur which are not covered in this manual, use care

and good judgment. Contact Customer Support for assistance and

the name of your nearest servicing dealer.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snow throwers. Never use

your hand to clean out the discharge chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

Maintenance & Storage

1. Never tamper with safety devices. Check their proper operation

regularly. Refer to the maintenance and adjustment sections of this

manual.

2. Before cleaning, repairing, or inspecting machine disengage all

control levers and stop the engine. Wait until the auger come to a

complete stop. Disconnect the spark plug wire and ground against

the engine to prevent unintended starting.

3. Check bolts and screws for proper tightness at frequent intervals to

keep the machine in safe working condition. Also, visually inspect

machine for any damage.

4. Do not change the engine governor setting or over-speed the

engine. The governor controls the maximum safe operating speed of

the engine.

5. Snow thrower shave plates and skid shoes are subject to wear and

damage. For your safety protection, frequently check all components

and replace with original equipment manufacturer’s (OEM) parts

only. “Use of parts which do not meet the original equipment

specifications may lead to improper performance and compromise

safety!”

6. Check control levers periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the adjustment

section in this operator’s manual for instructions.

7. Maintain or replace safety and instruction labels, as necessary.

8. Observe proper disposal laws and regulations for gas, oil, etc. to

protect the environment.

9. Prior to storing, run machine a few minutes to clear snow from

machine and prevent freeze up of auger.

10. Never store the machine or fuel container inside where there is

an open flame, spark or pilot light such as a water heater, furnace,

clothes dryer, etc.

11. Always refer to the operator’s manual for proper instructions on

off-season storage.

12. Check fuel line, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

13. Do not crank engine with spark plug removed.

14. According to the Consumer Products Safety Commission (CPSC) and

the U.S. Environmental Protection Agency (EPA), this product has an

Average Useful Life of seven (7) years, or 60 hours of operation. At the

end of the Average Useful Life have the machine inspected annually

by an authorized service dealer to ensure that all mechanical and

safety systems are working properly and not worn excessively.

Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any way.

Tampering with the governor setting can lead to a runaway engine and

cause it to operate at unsafe speeds. Never tamper with factory setting of

engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal EPA

emission regulations for SORE (Small Off Road Equipment) are certified

to operate on regular unleaded gasoline, and may include the following

emission control systems: Engine Modification (EM), Oxidizing Catalyst (OC),

Secondary Air Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Section 1 — important Safe operation practiceS

WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow

the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before

attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to assemble and

operate.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running. There are rotating

blades inside.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running. There are rotating

blades inside.

WARNING— ROTATING AUGER

Do not put hands or feet near rotating parts, in the auger housing or chute assembly. Contact

with the rotating parts can amputate hands and feet.

WARNING—THROWN OBJECTS

This machine may pick up and throw objects which can cause serious personal injury.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine and

muffler to cool before touching.

Assembly & Set-Up

Thank you for purchasing your new equipment. It was carefully engineered

to provide excellent performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment. It instructs

you how to safely and easily set up, operate and maintain your machine.

Please be sure that you, and any other persons who will operate the

machine, carefully follow the recommended safety practices at all times.

Failure to do so could result in personal injury or property damage.

All information in this manual is relative to the most recent product

information available at the time of printing. Review this manual frequently

to familiarize yourself with the machine, its features and operation. Please

be aware that this Operator’s Manual may cover a range of product

specifications for various models. Characteristics and features discussed

and/or illustrated in this manual may not be applicable to all models. The

manufacturer reserves the right to change product specifications, designs

and equipment without notice and without incurring obligation.

The engine manufacturer is responsible for all engine-related issues with

regards to performance, power-rating, specifications, warranty and service.

Please refer to the engine manufacturer’s Owner’s/Operator’s Manual,

packed separately with your machine, for more information.

If you have any problems or questions concerning the machine, phone your

local authorized service dealer or contact us directly. We want to ensure

your complete satisfaction at all times.

Throughout this manual, all references to right and left side of the machine

are observed from the operating position.

Thank You

NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the

model depicted may differ from yours. Refer to Figure 2-1 to identify the chute control on your specific unit.

Four Way Chute Control

Pages 9

Standard Side Chute Crank Control

Standard Side Chute

Crank Control

Chute Control Rod

Chute

Assembly

Chute Assembly

Page 8

Electric Chute Control

Pages 10

Overhead Chute Control

(with Chute Control Rod) Page 11

Overhead Chute

Control Rod

Manual Chute

Control Rod

Chute

Assembly

Chute

Assembly

Two Way Overhead Chute Control

(with Flex Shaft and Steel Chute)

Page 12

Chute Assembly

Flex Shaft

Figure 2-1

6 Section 2 — ASSembly & Set-Up

Tools Required

• Adjustable Wrench or Socket Set

• Needle Nose Pliers

Handle Assembly

1. Cut cable ties securing chute control rod

or flex shaft to lower handle (if applicable)

and set aside.

NOTE: If your unit is equipped with a

cable tie securing the control cables to the

engine do not cut the cable tie.

2. Loosen the top two lock nuts (a) securing

the upper and lower handle and remove

the two carriage screws (b) from the lower

handle and set aside as shown in Figure

2-2. Refer to inset in Figure 2-2 for models

with side support.

Figure 2-2

3. Place shift lever in Forward-6 position

(if equipped).

4. Observe lower rear area of equipment to

be sure both cables are aligned and seated

properly in roller guides. See Figure 2-3.

NOTE: On select units, chute-pitch control

cables will be routed under the engine on the

left side and will not use roller guides.

Figure 2-3

5. Pull up on the upper handle, align the

upper handle with the lower handle. See

Figure 2-4.

6. Reattach the two carriage screws and lock

nuts removed earlier as shown in Figure

2-2.

7. Finish securing the handle by tightening

the top two lock nuts loosened earlier.

Remove and discard any rubber bands, if

present. They are for packaging purposes

only.

Figure 2-4

Chute Clean-Out Tool

The chute clean-out tool is fastened to the top

of the auger housing with a mounting clip. See

Figure 2-5.

Figure 2-5

Tires

Pneumatic (Air-Pressurized) Tires

The tires are over-inflated for shipping purposes.

Check the tire pressure before operating the

snow thrower. Refer to the tire side wall for tire

manufacturer’s recommended psi and deflate (or

inflate) the tires as necessary.

WARNING: Under any

circumstance do not exceed

manufacturer’s recommended psi.

Equal tire pressure should be

maintained at all times. Excessive

pressure when seating beads may

cause tire/rim assembly to burst

with force sufficient to cause serious

injury. Refer to sidewall of tire for

recommended pressure.

NOTE: Equal tire pressure is to be maintained at

all times for performance purposes.

Non-Pneumatic (Airless) Tires

Some units are equipped with non-pneumatic

tires. Therefore, these airless tires are considered

maintenance free with regards to air pressure

Drift Cutters (If Equipped)

The drift cutters are mounted inverted at the

factory for shipping purposes.

Standard

1. Remove two screws (a) and lock nuts (b)

that secure each drift cutter, and remove

them from the sides of auger housing. See

Figure Figure 2-6.

2. Turn the drift cutters around and position

them as shown in Figure 2-6 to the outside

of the auger housing.

(a)

(b)

Figure 2-6

3. Attach drift cutters with screws (a) and

lock nuts (b) removed in Step 1.

Tool-less

1. Remove two carriage bolts (a) and wing

nuts (b) that secure each drift cutter, and

remove them from the sides of auger

housing. See Figure 2-7.

2. Turn the drift cutters around and position

them as shown in Figure 2-7 to the outside

of the auger housing.

(b)

(a)

Figure 2-7

3. Attach drift cutters with carriage bolts (a)

and wing nuts (b) removed in Step 1.

(a)

(b)

(a)

(b)

(a)

7Section 2 — ASSembly & Set-Up

Chute Control Cable Routing

(If Equipped)

For units equipped with chute cables, ensure

they are routed properly. Chute control cables

are routed through a single wire guide (a) on

top of the engine and/or through two wire

guides (b) located on the left side of the unit.

NOTE: For smoothest operation, cables should

all be to the left of the chute directional control

rod.

NOTE: The number of cables routed through

the wire guides will depend on your model.

1. Locate cable guide(s) and perform the

following:

• Units with Top Mounted Wire Guide

(a) - Check that all cables are properly

routed through cable guide on top of

engine. See Figure 2-8.

• Units with Side Mounted Wire Guides

(b) - Check that all cables are properly

routed through the wire guide below

the left side of the engine and the wire

guide below the chute control head.

See Figure 2-8.

(b)

(a)

(c)

Figure 2-8

Shear Pins

Replacement auger shear pins and cotter pins

are included with this manual.

On select units, holes are provided in the rear

of the handle panel for shear pin (a) and bow-

tie cotter pin (b) storage as shown in Figure 2-9.

If not provided, make sure to store them in a

safe place until needed.

Refer to Controls and Operation Section

for more information regarding shear pin

replacement.

(a)

(b)

(a)

(b)

(a)

(b)

Figure 2-9

NOTE: Three stage units come with four (4)

shear pins and bow-tie cotter pins.

Adding Fuel & Oil

Refer to the Engine Operator’s Manual for

information on adding fuel and oil.

Chute Assembly Options

Refer to Figure 2-1 and proceed to your

applicable Chute Control Style on pages 8-13.

8 Section 2 — ASSembly & Set-Up

1. Position the chute assembly over the base,

seated securely on adapter. See Figure

2-11.

Figure 2-11

2. Close flange keepers to secure chute

assembly to chute base. Flange keepers

will click into place when properly secure.

See Figure 2-12.

Figure 2-12

NOTE: Ensure the lower chute is secured

to the flange on the chute base. The

lower edge of the chute keeper should

be positioned below the flange on the

chute base after being clicked into place.

If flange keepers will not easily click into

place, use palm of your hand to apply

swift, firm pressure to the back of each.

Chute Directional Control Assembly

1. Remove plastic cap (if present), flat washer

(a) and hairpin clip (b) from end of chute

directional control assembly.

See Figure 2-13.

(a)

(b)

Figure 2-13

2. Insert end of chute directional control

assembly into lower bracket and secure

chute directional control assembly with

flat washer (a) and hairpin clip (b) removed

in Step 1. If necessary, lower bracket

can be adjusted. Refer to Chute Bracket

Adjustment in Service section

on page 13.

STOP

STOP! Continue to Adjustments -

(page 13).

Standard Side Crank Chute Control

Figure 2-10

9Section 2 — ASSembly & Set-Up

Four Way Chute Control

Figure 2-14

1. Remove hairpin clip (a), wing nut (b) and

hex screw (c) from chute control assembly

and clevis pin (d) and bow-tie cotter pin

(e) from chute support bracket. See Figure

2-15.

(a)

(b)

(c)

(d)

(e)

Chute Control

Assembly

Chute

Support

Bracket

Chute

Base

Figure 2-15

2. Insert round end of the chute control rod

(hole pointing upward) as far as possible

into chute control assembly. See Figure

2-16.

Figure 2-16

3. Place chute onto chute base and ensure

chute control rod is positioned under

handle panel. Install hex screw (c)

removed in Step 1, but do not secure with

wing nut at this time. See Figure 2-17.

(c)

Figure 2-17

4. Squeeze trigger on joystick and rotate

chute by hand to face forward. The holes

in chute control input will be facing up.

See Figure 2-18.

Chute Control Input

Top View

Joystick

Figure 2-18

NOTE: Chute will not rotate without

squeezing trigger on joystick.

5. Rotate joystick to one o’clock position so

the arrow on pinion gear below control

panel faces upward.

See Figure 2-19.

Figure 2-19

6. Insert chute control rod (hole pointing

upward) into pinion gear below joystick.

See Figure 2-20.

Figure 2-20

NOTE: Chute control rod will fit snug into

pinion gear. Support rear of dash panel

with one hand while inserting rod with

your other hand to ensure rod is inserted

all the way into pinion gear.

NOTE: The hole in the chute directional

control rod is a reference for aligning rod

with indicator arrow on pinion gear, and

will be visible after rod has been inserted.

7. Push chute control rod toward control

panel until hole in rod lines up with hole

in chute control input closest to chute

control assembly and insert hairpin clip (a)

removed in Step 1. See Figure 2-21.

(a)

Figure 2-21

NOTE: Second hole is used to achieve

further engagement of chute control

rod into pinion gear if required. Refer to

Service section for Chute Control Rod

adjustments.

8. Finish securing chute control assembly to

chute support bracket with wing nut (b),

clevis pin (d), and bow-tie cotter pin (e)

removed in Step 1.

9. It is important that all cables be routed

properly. Refer to “Chute Control Cable

Routing” page on 7.

STOP

STOP! Continue to Adjustments -

(page 13).

10 Section 2 — ASSembly & Set-Up

1. Remove cotter pin (a), wing nut (b) and

hex screw (c) from chute control assembly.

Remove clevis pin (d) and bow-tie cotter

pin (e) from chute support bracket.

See Figure 2-23.

(c)

(e)

Chute

Support

Bracket

Chute Base

(a)

(d)

(b)

Chute Control

Assembly

Figure 2-23

2. Insert round end of chute control rod into

chute control assembly. Push rod as far

into chute control assembly as possible,

keeping holes in rod pointing upward. See

Figure 2-24.

Figure 2-24

3. Place chute onto chute base and ensure

chute control rod is positioned under

handle panel. Secure chute control

assembly to chute support bracket with

clevis pin (d) and bow-tie cotter pin (e)

removed in Step 1. See Figure 2-25.

(d)

(e)

Figure 2-25

4. Finish securing chute control assembly by

installing hex screw (c) and wing nut (b)

removed in Step 1. See Figure 2-26.

(c)

(b)

Figure 2-26

5. Insert other end of chute control rod into

coupler below handle panel. Make sure

to line up flat end of rod and flat end

of coupler. You may need to rotate rod

around until these two surfaces line up.

See Figure 2-27 inset.

Figure 2-27

6. Push chute control rod toward the control

panel until hole in rod lines up with

middle hole in chute control input and

insert cotter pin (a) removed in

Step 1. See Figure 2-28.

(a)

Figure 2-28

NOTE: There is a reference hole provided

at rear end of control rod to help know

when holes are vertical.

NOTE: Hole furthest from chute control

assembly is used to achieve further

engagement of chute control rod into

coupler if required. Refer to Service

section for Chute Control Rod adjustment

on page 20.

Hole closest to chute control assembly

is used for manual movement of chute

assembly if required. Refer to Controls &

Operation section on page 16.

7. It is important that all cables be routed

properly. Refer to “Chute Control Cable

Routing” page on 7.

NOTE: On units equipped with a cable

tie securing the cables to the rear of the

gas tank, pull the cables towards the chute

and pull the cable tie snug to secure the

cables in place.

NOTE: For smoothest operation, cables

should all be to left of chute directional

control rod.

STOP

STOP! Continue to Adjustments -

(page 13).

Electric Chute Control

Figure 2-22

11Section 2 — ASSembly & Set-Up

1. Remove wing nut (a) and hex

screw (b) from chute control assembly and

clevis pin (c) and cotter pin (d) from chute

support bracket. Position chute assembly

(forward-facing) over chute base. See

Figure 2-30.

(a)

(b)

(c)

(d)

Chute Control

Assembly

Chute

Support

Bracket

Chute

Base

Figure 2-30

2. Place chute assembly onto chute base and

secure chute control assembly to chute

support bracket with clevis pin (c) and

cotter pin (d) removed in Step 1.

See Figure 2-31.

Figure 2-31

3. Finish securing chute control assembly to

chute support bracket with wing

nut (a) and hex screw (b) removed in Step

1. See Figure 2-32.

Figure 2-32

4. Guide the chute crank rod through the

bracket located on the rear of the handle

panel . See Figure 2-33.

Figure 2-33

5. Remove the cotter pin (a) and insert the

chute crank rod (b) into the connector on

the chute control assembly.See Figure

2-34.

6. Align the hole in the chute crank rod with

the hole in the connector, secure with

cotter pin (a) previously removed.

(a)

(b)

Figure 2-34

STOP

STOP! Continue to Adjustments -

(page 13).

Overhead Chute Control (with Chute Control Rod)

Figure 2-29

(a)

(b)

(c)

(d)

12 Section 2 — ASSembly & Set-Up

1. Remove lock nuts (a) and hex screws (b)

from chute support bracket (this will

require two wrenches). See Figure 2-36.

Chute

Assembly

Chute Base

Chute

Support

Bracket

Chute Control

Assembly

(a)

(b)

Figure 2-36

2. Place chute assembly onto chute base

and chute control assembly onto chute

support bracket. See Figure 2-37.

3. Secure chute control assembly to chute

support bracket with lock nuts (a) and hex

screws (b) removed in Step 1. See Figure

2-37.

4. Remove hairpin clip (a) from rear of chute

control assembly. See Figure 2-38.

5. Insert flex shaft (b) removed during

Handle Assembly from lower handle into

rear of chute directional control assembly.

See Figure Figure 2-38. Secure flex shaft to

chute control assembly with hairpin clip

(a) removed in Step 4.

(a)

(b)

Figure 2-37

(a)

(b)

Figure 2-38

6. Insert hex end of flex shaft into chute

control rod coupling under dash panel.

See Figure 2-39.

Figure 2-39

7. Ensure speed selector is in fastest forward

speed.

8. Remove cotter pin (a) and washer (b) from

ferrule on end of shift rod. See Figure 2-40

inset.

(a)

(b)

Shift Rod

Ferrule

Figure 2-40

9. Pivot shift bracket downward as far as it

will go. See Figure 2-41.

Figure 2-41

10. Insert ferrule into top hole of shift lever

and secure with cotter pin (a) and washer

(b) removed in Step 8. Ferrule may need to

be adjusted up or down.

11. It is important that all cables be routed

properly. Refer to “Chute Control Cable

Routing” page on 7.

NOTE: On units equipped with a cable tie

securing the cables to the rear of the gas

tank, pull the cables towards the chute

and pull the cable tie snug to secure the

cables in place.

STOP

STOP! Continue to Adjustments -

(page 13).

Two Way Overhead Chute Control (with Flex Shaft and Steel Chute)

Figure 2-35

13Section 2 — ASSembly & Set-Up

Skid Shoes

The snow thrower skid shoes are adjusted at

the factory, set roughly 1/8” below the shave

plate. Adjust them downward, if desired, prior to

operating the snow thrower.

CAUTION: Use extreme caution

when on gravel and adjust auger

housing height to clear gravel or

crushed rock surfaces to avoid

picking up and throwing gravel or

crushed rock.

• For close snow removal on a smooth

surface, raise skid shoes higher on auger

housing.

• Use a lower position when area to be

cleared is uneven, such as a gravel

driveway.

NOTE: If you choose to operate unit on a gravel

surface, keep skid shoes in position for maximum

clearance between ground and shave plate.

NOTE: Some models are equipped with

reversible skid shoes and may be turned over to

increase their lifespan.

To adjust skid shoes:

1. Loosen hex nuts, washers (if equipped)

and carriage bolts. Move skid shoes to

desired position.

2. Make certain entire bottom surface of skid

shoe is against ground to avoid uneven

wear on skid shoes.

3. Retighten hex nuts, washers (if equipped)

and carriage bolts securely.

See Figure 2-44.

(a)

NOTE: Standard skid shoes shown

for illustration.

(a)

(b)

Figure 2-44

Auger Control Test

WARNING! Prior to operating

your unit, carefully read and follow

all instructions below. Perform all

adjustments to verify your

equipment is operating safely and

properly.

Refer to Controls & Operation section (page 14)

for the location of auger control lever and check

adjustment as follows:

1. When auger control lever is released and

in disengaged “UP” position, the cable

should have very little slack. It should NOT

be tight.

2. In a well-ventilated area, start the snow

thrower engine. Refer to your Engine

Operator’s Manual.

3. While standing in the operator’s position

(behind the unit), depress the auger

control lever to engage auger.

4. Allow auger to remain engaged for

approximately ten (10) seconds before

releasing auger control lever. Repeat this

several times.

5. With auger control lever in disengaged

“UP” position, walk to front of machine.

6. Confirm that auger has completely

stopped rotating and shows NO signs

of motion. If auger shows ANY signs of

rotating, immediately return to operator’s

position and shut OFF engine. Wait for ALL

moving parts to stop before readjusting

auger control lever.

7. To readjust the auger control cable, loosen

upper hex screw (a) on auger control

bracket. See Figure 2-45.

8. Position bracket upward to provide more

slack (or downward to increase cable

tension). See Figure 2-45. Retighten upper

hex screw (a).

9. Repeat Steps 2 through 6 to verify proper

adjustment has been achieved.

Auger Control

Bracket

(a)

Figure 2-45

Adjustments

Chute Assembly

On units with manual chute tilt, the distance

snow is thrown can be adjusted by changing

angle of chute assembly. To do so:

1. Loosen wing knob found on left side of

chute assembly. See Figure 2-42.

Figure 2-42

2. Pivot chute upward or downward before

retightening wing knob.

Chute Bracket (If Equipped)

If spiral at bottom of the chute directional

control is not fully engaging with chute

assembly, chute bracket needs to be adjusted.

To do so:

1. Loosen two nuts (a) which secure chute

bracket and reposition it slightly. See

Figure 2-43.

Figure 2-43

2. Retighten nuts.

Controls & Operation

† If Equipped

Manual Chute

Directional

Control †

Drift Cutters †

LED Light Bar †

Overhead

Chute

Directional

Control †

Overhead

Chute

Directional

Control †

Flex Shaft Chute

Directional

Control †

Headlight †

Headlight

4-Way Chute

Directional Control

Joystick †

Heated

Grips †

Heated Grip

Switch †

Headlight †

Chute Directional

Control Rod

Electric Chute

Directional

Control

Joystick †

Steering

Trigger

Control †

Two-Way

Chute-Pitch

Control™ †

Standard Chute

Directional Control †

Shift Lever

Augers

Skid Shoe

Clean Out

Tool

Chute Assembly

Drive Control

Lever

Auger Control Lever

Auger Housing

Shift Lever

Two-Way

Indexed

Chute-Pitch

Control †

Heated Grip Switch †

Headlight †

Figure 3-1

15Section 3 — controlS & operation

Snow thrower controls and features are

described below and illustrated in Figure 3-1.

NOTE: This Operator’s Manual covers several

models. Snow thrower features may vary by

model. Not all features in this manual are

applicable to all snow thrower models and the

snow thrower depicted may differ from yours.

NOTE: All references to the left or right side

of the snow thrower are from the operator’s

position. Any exceptions will be noted.

Engine

Refer to the Engine Operator’s Manual for

details regarding all engine-related controls and

features.

Shift Lever (6-Speed Transmission)

(If equipped)

The shift lever is located on the handle panel and

is used to determine ground speed and direction

of travel.

Forward

There are six forward (F) speeds. Position

one (1) is the slowest and position six (6) is the

fastest.

Reverse

There are two reverse (R) speeds. Position one (1)

is the slower and position two (2) is the faster.

Shift Lever (Hydro Transmission)

(If equipped)

The shift lever is located on the handle panel and

is used to determine ground speed and direction

of travel. The further forward the lever is the

faster the unit will travel. Moving past the detent

position to the reverse direction will move the

unit in reverse.

Chute Assembly

Snow drawn into the auger housing is

discharged out the chute assembly.

Skid Shoes

Position skid shoes based on surface conditions.

Adjust upward for hard-packed snow. Adjust

downward when operating on gravel or crushed

rock surfaces. See Skid Shoe Adjustment section

on page 13.

Augers

When engaged, the augers rotate and draw

snow into the auger housing.

Headlight(s) (If Equipped)

The headlight is located on the handle panel and

is automatically turned ON when the engine is

started.

LED Light Bar (If Equipped)

The LED headlight is located on top of the auger

housing and is automatically turned ON when

the engine is started.

Drift Cutters (If Equipped)

The drift cutters are designed for use in deep

snow. Their use is optional for normal snow

conditions. Maneuver unit so that the cutters

penetrate a high standing snow drift to assist

snow falling into the augers for throwing.

Heated Grips (If Equipped)

Caution: It is recommended that

you wear gloves when using the

heated grip. If the heated grips

become too hot, turn it OFF.

To activate the heated grips, move switch found

on top (a) of or on the rear (b) of dash panel into

the ON position. See Figure 3-2. To turn OFF

heated grips, move switch to the OFF position.

Switch ON Switch OFF

(b)

(a)

(b)

(a)

Switch ON

Switch OFF

Figure 3-2

Auger Control Lever

The auger control lever is located on the left

handle. Squeeze the control lever against the

handle to engage the augers and start snow

throwing action. Release to stop.

See Figure 3-3.

Figure 3-3

IMPORTANT: Refer to the Auger Control Test

information on page 13 prior to operating your

snow thrower. Read and follow all instructions

carefully and perform all adjustments to verify

your snow thrower is operating safely and

properly.

Drive Control Lever / Auger Clutch Lock*

The drive control lever is located on the right

handle. Squeeze the control lever against the

handle to engage the wheel drive. Release to

stop. See Figure 3-4.

Figure 3-4

*On select models, the drive control lever also

locks the auger control lever so that you can

operate the chute directional control without

interrupting the snow throwing process. If the

auger control lever is engaged simultaneously

with the drive control lever, the operator can

release the auger control lever (on the left

handle) and the augers will remain engaged.

Release both control levers to stop augers and

wheel drive.

NOTE: Always release drive control lever before

changing speeds on all units except hydrostatic

models. Failure to do so will result in increased

wear on your machine’s drive system.

Steering Trigger Controls

(If Equipped)

The left and right wheel steering trigger controls

are located on the underside of the handles.

Refer to Figure 3-5.

IMPORTANT: Units with Hydro Transmission

- When moving the unit without starting the

engine, squeeze both right and left triggers to

disengage the drive.

Figure 3-5

• Squeeze the right trigger control to turn

right.

• Squeeze the left trigger control to turn

left.

CAUTION: Operate the snow

thrower in open areas until you are

familiar with these controls.

16 Section 3 — controlS & operation

4-Way Chute Directional Control

Joystick (If Equipped)

The 4-Way chute directional control joystick is

located on the left side of the dash panel.

• To change the direction in which snow

is thrown, squeeze the button on the

joystick and pivot the joystick to the right

or to the left. See Figure 3-6.

• To change the angle/distance which snow

is thrown, pivot the joystick forward or

backward.

Figure 3-6

Overhead Chute Directional Control

(If Equipped)

The overhead chute directional control is

located at the rear of the snowthrower towards

the left side of the unit under the handle panel.

To change the direction in which snow is thrown,

rotate chute directional control. See Figure 3-7.

Figure 3-7

Standard Chute Directional Control If

Equipped)

The standard chute directional control is located

on the left side of the unit. To change direction

in which snow is thrown, rotate chute directional

control. See Figure 3-7.

Electric Chute Directional Control

Joystick (If Equipped)

The electric chute directional control joystick is

located on the right side of the dash panel. Refer

to Figure 3-8.

• To change the direction in which snow is

thrown, move the joystick to the right or

to the left.

• To change the angle/distance which snow

is thrown, pivot the joystick forward or

backward.

DIRECTIONAL CONTROL

ELECTRIC CHUTE

CHUTE

ROTATE

LEFT

CHUTE

ROTATE

RIGHT

CHUTE TILT UP

CHUTE TILT DOWN

Figure 3-8

Manual Chute Directional Control

(Equipped on units with Electric Chute

Directional Control Joystick)

Proceed as follows to utilize manual chute

directional control if needed:

1. Remove cotter pin (a) from either of the

holes furthest from the chute assembly on

chute rotation assembly.

2. Push in chute control rod until the hole

in it lines up with the third hole in chute

rotation assembly. See Figure 3-9.

(a)

Figure 3-9

3. Reinsert cotter pin (a) through this hole

and chute control rod as shown in

Figure 3-9.

4. Grasp indented portion of chute control

rod and manually rotate chute assembly

to the right or to the left. See Figure 3-10.

Figure 3-10

Overhead Chute Directional Control

(With Flex Shaft) (If Equipped)

The overhead chute directional control is

located at the rear of the unit towards the left

side under the handle panel. To change direction

in which snow is thrown, rotate chute directional

control. See Figure 3-11.

CHUTE DIRECTIONAL CONTROL

DISCHARGE

LEFT

DISCHARGE

RIGHT

CHUTE TILT

DOWN

CHUTE TILT

Figure 3-11

Two-Way Chute-Pitch Control™

(If Equipped)

The two-way chute-pitch control is located on

the left side of the dash panel and is used to

control the distance of snow discharge from the

chute. Tilt the lever forward or rearward to adjust

the distance snow will be thrown.

Two-Way Chute-Pitch Control

• To Reduce the Distance Snow is Thrown:

Move the lever forward to pivot the upper

chute down. See Figure 3-12.

• To Increase the Distance Snow is Thrown:

Move the lever rearward to pivot the

upper chute upward. See Figure 3-12.

Two-Way Indexed Chute-Pitch Control

• To Reduce the Distance Snow is Thrown:

Disengage lever from the current chute-

pitch setting. Move the lever forward to

pivot the upper chute down to the desired

pitch setting (a). See Figure 3-12.

• To Increase the Distance Snow is Thrown:

Disengage lever from the current chute-

pitch setting. Move the lever rearward

to pivot the upper chute upward to the

desired pitch setting (a). See Figure 3-12.

TWO-WAY CHUTE-PITCH CONTROL

CHUTE TILT

DOWN

CHUTE TILT

TWO-WAY INDEXED CHUTE-PITCH CONTROL

CHUTE TILT

DOWN

CHUTE TILT

(a)

Figure 3-12

17Section 3 — controlS & operation

Starting and Stopping the Engine

WARNING! Always keep hands and

feet clear of moving parts. Do not

use a pressurized starting fluid.

Vapors are flammable.

Refer to the Engine Operator’s Manual for

instructions on starting and stopping the engine.

To Engage Drive

1. With the engine running and the throttle

control in the Fast (rabbit) position, move

the shift lever into one of the six forward

(F) positions or two reverse (R) positions.

Select a speed appropriate for the snow

conditions and a comfortable pace.

2. Squeeze the drive control lever against the

handle and the snow thrower will move.

Release it and drive motion will stop.

To Engage Augers

To engage the augers and start throwing snow,

squeeze the auger control lever against the left

handle. Release to stop the augers.

To Steer (If Equipped)

With the drive control lever engaged, squeeze

the right steering trigger control to turn right.

Squeeze the left steering trigger control to turn

left.

CAUTION: Operate the snow

thrower in open areas and at slow

speeds until you are familiar with

the drive control and comfortable

operating the steering controls.

Replacing Shear Pins

The augers are secured to the spiral shaft with

shear pins (a) and cotter pins (b). If the auger

should strike a foreign object or ice jam, the

snow thrower is designed so that the pins may

shear. If the augers will not turn, check to see if

the pins have sheared. See Figure 3-13.

IMPORTANT: ALWAYS use the correct OEM

replacement shear pin.

2-Stage Snow Throwers

• The auger is secured to the spiral shaft

using gold colored shear pins (OEM Part

No. 738-04124A).

3-Stage Snow Throwers

• The side augers and central accelerator

augers are secured to the spiral shaft

using black shear pins (OEM part number

738-05273).

NOTE: 3-Stage shown.

(a)

(b)

(c)

Figure 3-13

IMPORTANT: On 3-stage units, there

is an additional shear pin in the rear

accelerator.

CAUTION: NEVER replace the

auger shear pins with anything

other than OEM Part No. 738-04124A

(gold colored replacement shear

pins) or 738-05273 (Black colored

replacement shear pins). Any

damage to the auger gearbox or

other components as a result of

failing to do so will NOT be covered

by your snow thrower’s warranty.

WARNING! Always turn OFF the

snow thrower’s engine and remove

the key prior to replacing shear pins.

Clearing a Clogged Chute Assembly

WARNING! Never use your hands

to clear a clogged chute assembly.

Shut OFF engine and remain behind

handles until all moving parts have

stopped before unclogging.

The chute clean-out tool is conveniently fastened

to the rear of the auger housing with a mounting

clip. Should snow and ice become lodged in the

chute assembly during operation, proceed as

follows to safely clear the chute assembly and

chute opening:

1. Release both the Auger Control Lever and

the Drive Control Lever.

2. SHUT THE ENGINE OFF! Refer to the Engine

Operator’s Manual. Remove the safety key.

3. Remove clean-out tool from the clip which

secures it to the rear of the auger housing.

4. Use the shovel-shaped end of the clean-

out tool to dislodge and scoop any snow

and ice which has formed in and near the

chute assembly. Always use the clean-out

tool, not your hands. Refer to the separate

supplement for clean-out tool ordering

information.

5. Refasten the clean-out tool to the

mounting clip on the rear of the auger

housing, reinsert the safety key and start

the snow thrower’s engine.

6. While standing in the operator’s position

(behind the snow thrower), engage the

auger control lever for a few seconds to

clear any remaining snow and ice from the

chute assembly.

Service

WARNING! Before servicing,

repairing or inspecting the snow

thrower, disengage the auger

control lever. Stop the engine and

remove the safety key to prevent

unintended starting.

Maintenance

Engine

Refer to Engine Operator’s Manual.

Tire Pressure

Refer to Assembly & Set-up section (page 6) for

information regarding tire pressure.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom

of the snow thrower are subject to wear. They

should be checked periodically and replaced

when necessary.

NOTE: Some units are equipped with reversible

skid shoes and may be turned over to increase

their lifespan.

To remove skid shoes (Deluxe shown):

1. Remove four carriage bolts (a) and hex

flange nuts (b) and flat washers (c) which

secure them to the unit.

2. Rotate and reassemble new skid shoes

with four carriage bolts (a) (two on each

side) and hex flange nuts (b) and flat

washers (c). Refer to Figure 4-1.

NOTE: Augers not shown for clarity

(a)

(c)

(b)

Figure 4-1

To remove shave plate:

1. Allow the engine to run until it is out of

fuel. Do not attempt to pour fuel from the

engine.

2. Carefully pivot unit up and forward so that

it rests on the auger housing.

3. Remove carriage bolts (a) and hex

nuts (b) which attach it to auger housing.

See Figure 4-2.

4. Reassemble new shave plate, making sure

heads of carriage bolts are to the inside of

housing. Tighten securely.

See Figure 4-2.

(a)

(b)

Figure 4-2

NOTE: The shave plate on select units (shown

in Figure 4-3) have a wear edge that can be

adjusted forward to prolong its life. As the shave

plate wears, it can be moved into a second

position.

To move adjustable shave plate (if equipped):

1. Allow engine to run until it is out of fuel.

Do not attempt to pour fuel from the

engine.

2. Carefully pivot unit up and forward so that

it rests on auger housing.

3. Loosen rear skid shoe bolts (a) on both

sides of equipment housing and remove

carriage bolts and hex nuts which attach

shave plate to auger housing.

See Figure 4-3.

4. Slide shave plate downward into second

position. Reinstall and tighten all bolts

securely. See Figure 4-3.

(a)

Figure 4-3

Lubrication

Gear Shaft (If Equipped)

The gear (hex) shaft should be lubricated at least

once a season or after every twenty-five (25)

hours of operation.

1. Allow engine to run until it is out of fuel.

2. Carefully pivot unit up and forward so that

it rests on auger housing.

3. Remove frame cover from underside of

unit by removing self-tapping screws (a)

which secure it. Refer to Figure 4-4.

(a)

Figure 4-4

4. Apply a light coating of Bostik Regular

Grade Never-Seez® to hex shaft.

See Figure 4-5.

Figure 4-5

NOTE: When lubricating hex shaft, be careful

not to get any lubricant on aluminum drive plate

or rubber friction wheel. Doing so will hinder

unit’s drive system. Wipe off any excess or spilled

lubricant .

Wheels

At least once a season, remove both wheels.

Clean and coat axles with a multipurpose

automotive grease before reinstalling wheels.

Side Chute Crank Control (If Equipped)

Once a season, lubricate eye-bolt bushing and

the spiral with 3-in-1 oil.

Auger Shaft

At least once a season, remove shear pins (a)

and cotter pins (b) from auger shaft(s). Spray

lubricant inside shaft and around spacers and

flange bearings found at either end of shaft(s).

See Figure 4-6.

19Section 4 — Service

(a)

(b)

NOTE: Three Stage Augers Shown

(a)

(b)

Figure 4-6

IMPORTANT: On 3-stage units, there

is an additional shear pin in the rear

accelerator.

Adjustments

Shift Rod (If Equipped)

If full range of speeds (forward and reverse)

cannot be achieved, adjust shift rod as follows:

1. Place shift lever in fastest forward speed

position.

2. Remove cotter pin (a) and washer (b) from

adjustment ferrule on shift rod and pull it

out from shift lever. See Figure 4-7.

(a)

(b)

Figure 4-7

3. Pivot shift bracket downward as far as it

will go. See Figure 4-8.

Figure 4-8

4. Rotate ferrule up or down on shift rod as

necessary until it lines up with upper hole

in shift lever. Refer to Figure 4-7 inset.

5. Insert the ferrule into the upper hole and

secure with the washer and cotter pin.

Shift Cable (If Equipped)

If full range of speeds (forward and reverse)

cannot be achieved, adjust shift cable as follows:

1. Place shift lever in fastest forward speed

position.

2. Loosen hex nut (a) on shift cable index

bracket. See Figure 4-9.

(a)

Figure 4-9

3. Pivot bracket downward to take up slack

in cable.

4. Retighten hex nut.

5. If further adjustment is necessary move

the shift cable to one of the alternate

holes in the shift cable index bracket.

Auger Control

Refer to Assembly & Set-up section for

instructions on adjusting auger control cable.

Skid Shoes

Refer to Assembly & Set-up section (page 13) for

instructions on adjusting skid shoes.

Drive Control (Models without Hydro

Transmission) (If Equipped)

When drive control lever is released and in

disengaged “UP” position, cable should have

very little slack. It should NOT be tight.

NOTE: If excessive slack is present in drive cable

or if unit’s drive is disengaging intermittently

during operation, the cable may be in need of

adjustment.

Check adjustment of drive control lever as

follows:

1. With drive control lever released, push

unit gently forward. It should roll freely.

2. Engage drive control lever and gently

attempt to push the unit forward. The

wheels should not turn. The unit should

not roll freely.

3. If equipped with a shift lever, with drive

control lever released, move shift lever

back and forth between the R2 position

and the F6 position several times. There

should be no resistance in the shift lever.

If any of the above tests failed, the drive cable is

in need of adjustment. Proceed as follows:

1. Shut OFF engine. Refer to the Engine

Operator’s Manual.

2. Loosen lower hex screw (a) on drive cable

bracket. See Figure 4-10.

3. Position bracket upward to provide more

slack (or downward to increase cable

tension).

4. Retighten upper hex screw.

5. Check adjustment of drive control lever

as described above to verify proper

adjustment has been achieved.

(a)

Drive Cable

Bracket

Hex Screw

Figure 4-10

Drive Control (Models with Hydro Transmission)

(If Equipped)

When drive control lever is released and in

disengaged “UP” position, cable should have

very little slack. It should NOT be tight.

NOTE: If excessive slack is present in drive cable

or if unit’s drive is disengaging intermittently

during operation, the cable may be in need of

adjustment.

1. Shut OFF engine. Refer to the Engine

Operator’s Manual.

2. Loosen upper hex screw on drive cable

bracket. See Figure 4-11.

Drive Cable

Bracket

Hex Screw

Figure 4-11

3. Position bracket upward to provide more

slack (or downward to increase cable

tension).

4. Retighten upper hex screw.

5. Check for excessive slack in drive control

cable. If necessary repeat Steps 2-4 to

re-adjust the drive control.

20 Section 4— Service

Chute Control Rod

(Four Way Chute Control) (If Equipped)

To adjust chute control rod for increased

engagement into the handle panel control,

proceed as follows:

1. Remove hairpin clip (a) from hole closest

to chute assembly on chute rotation

assembly.

2. Pull out chute control rod until hole in it

lines up with second hole in chute rotation

assembly. See Figure 4-12.

3. Reinsert hairpin clip (a) through this hole

and chute control rod.

(a)

Figure 4-12

Chute Assembly

Refer to Assembly & Set-up section for

instructions on chute assembly.

Chute Assembly (Overhead Chute Control) (If

Equipped)

If chute fails to remain stationary during

operation, pre-load of chute can be adjusted

by tightening hex nut found on front of chute

control assembly.

1. To increase preload, tighten

hex nut (a) clockwise in ¼ turn intervals.

The chute control rod will need to be held

stationary when tightening the nut.

See Figure 4-13.

(a)

Figure 4-13

2. If chute directional control is difficult to

crank, decrease preload by loosening hex

nut counter-clockwise in ¼ turn intervals.

Belt Replacement

Auger Belt

To remove and replace auger belt, proceed as

follows:

1. Allow engine to run until it is out of fuel.

Do not attempt to pour fuel from engine.

2. Remove plastic belt cover on front of

engine by removing two self-tapping

screws (a). See Figure 4-14.

(a)

Figure 4-14

NOTE: On models equipped with the LED

headlight on top of the auger housing, make

sure to unplug the wire harness before removing

the belt cover as shown inFigure 4-15.

Figure 4-15

3. Roll auger belt off engine pulley.

See Figure 4-16.

Figure 4-16

4. Carefully pivot the unit up and forward so

that it rests on the auger housing.

5. Remove frame cover from underside of

unit by removing self-tapping screws

which secure it. See Figure 4-4.

6. Loosen and remove shoulder bolt (a) which

acts as a belt keeper. See Figure 4-17.

7. Unhook the brake bracket spring from the

frame.

NOTE: Multi-speed unit shown.

(a)

Figure 4-17

8. Remove belt from around auger pulley,

and slip it between support bracket and

auger pulley. See Figure 4-18.

Figure 4-18

9. Replace auger belt by following

instructions in reverse order.

NOTE: Make sure to reinstall shoulder bolt

(a) and reconnect spring to frame after

installing a replacement auger belt. Refer

to Figure 4-17.

10. After replacing auger belt, perform Auger

Control test in Assembly & Set-Up section

(page 13).

Drive Belt

NOTE: See your authorized service dealer to

have drive belt replaced or contact Customer

Support.

La page charge ...

MTD 500 Series Manuel utilisateur

Marque: MTD

Modèle: 500 Series

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: MTD 500 Series User manual

MTD 500 Series Manuel utilisateur

MTD 500 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents