Simplicity 030437-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030437-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Manual No. 208551GS Revision D (01/27/2009)

Portable Generator

Operator’s Manual

This generator is rated in accordance with CSA (Canadian Standards

Association) standard C22.2 No. 100-04 (motors and generators).

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

material may be reproduced or transmitted in any form

without the express written permission of Briggs & Stratton

Power Products Group, LLC.

Husky® is a registered trademark

of The Home Depot.

Thank you for purchasing this quality-built Husky® generator. We are pleased that you’ve placed your confidence in the

Husky® brand. When operated and maintained according to the instructions in this manual, your Husky® generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator products and

how to avoid them. This generator is designed and intended only for supplying electrical power for operating compatible

electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is important that you read

and understand these instructions thoroughly before attempting to start or operate this equipment. Save these instructions for

future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages. There

are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Husky Customer Service by phone at (877) 370-7501. For engine related questions, call Robin America, Inc. at (800) 277-6246

or visit www.subarupower.com for a dealer locator.

Generator

Model Number

Revision

Serial Number

Date Purchased

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpack Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

System Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting to a Building’s Electrical System. . . . . . . . . . . . . . . . . . . . . . . . 8

Generator Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Features and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Cord Sets and Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting Electrical Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stopping the Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Charging a Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cold Weather Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Don’t Overload Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Generator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Generator Owner Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generator is an engine–driven, revolving field, alternating

current (AC) generator. It was designed to supply electrical

power for operating compatible electrical lighting, appliances,

tools and motor loads. The generator’s revolving field is

driven at about 3,600 rpm by a single-cylinder engine.

NOTICE:

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

Every effort has been made to ensure that the information in

this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the generator and this documentation at any time

without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency

and the California Air Resources Board.

Important Safety Information

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

Explosive Pressure

Chemical Burn

WARNING: Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

(even if windows and doors are open), including the generator

compartment of a recreational vehicle (RV).

WARNING: The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING: Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm. Wash hands after handling.

WARNING:

Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for a

long time after battery has been charged.

Slightest spark will ignite hydrogen and cause explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is extremely

caustic.

Contact with battery fluid will cause severe chemical burns.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

WARNING:

Generator produces hazardous voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING: Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING:

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury and/or

property damage.

NOTICE:

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

NOTICE:

Improper treatment of generator can damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

WARNING: Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING: Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING: Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING: Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate generator without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION:

Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Assembly

Your generator requires some assembly and is ready for use

after it has been properly serviced with the recommended

fuel and oil.

If you have any problems with the assembly of your generator,

please call the generator helpline at (877) 370-7501. If calling

for assistance, please have the model, revision, and serial

number from the identification label available. See Generator

Features and Controls for identification label location.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from

top to bottom.

The generator is supplied with:

• Battery charge cables

• Operator’s manual

• Engine operator’s manual

Verify Engine Oil Level

The generator engine is shipped from the factory filled with

oil (API SJ or higher 10W-30). This allows for generator

operation in the widest range of temperature and climate

conditions. Before starting the engine, check oil level and

ensure that engine is serviced as described in the engine

operator’s manual.

NOTE: See the engine operator’s manual to review oil

recommendations. Verify provided oil in engine is the correct

viscosity for current ambient temperature.

NOTICE: Any attempt to crank or start the engine before it

has been properly filled with the recommended oil will

result in equipment failure.

• Refer to engine operator’s manual for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Add Fuel

NOTE: Refer to engine operator’s manual and follow fuel

recommendations.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank (B). Be

careful not to overfill. Allow about 1/4" of tank space

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

IMPORTANT: Keep fuel tank area free of all debris, water and

ice. DO NOT block vent (D). Tank must breathe.

WARNING: Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Grounding Fastener

The generator neutral is floating, which means that the AC

stator winding is isolated from the grounding fastener and

the AC receptacle ground pins. On a floating neutral

generator the AC receptacle ground pins are not functional.

Electrical devices, such as a GFCI, requiring a functioning AC

receptacle ground pin will not operate.

Special Requirements

There may be Federal, local codes, or ordinances that apply

to the intended use of the generator. Please consult a

qualified electrician, electrical inspector, or the local agency

having jurisdiction:

• In some areas, generators are required to be registered

with local utility companies.

• This generator has a floating neutral and is not for use

on job sites requiring a bonded neutral.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician. The

connection must isolate the generator power from utility

power or other alternative power sources and must comply

with all applicable laws and electrical codes.

Generator Location

Clearances and Air Movement

Place generator outdoors in an area that will not accumulate

deadly exhaust gas. DO NOT place generator where exhaust

gas (A) could accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is kept

away from any windows, doors, ventilation intakes, or other

openings that can allow exhaust gas to collect in a confined

area. Prevailing winds and air currents should be taken into

consideration when positioning generator.

WARNING:

Generator produces hazardous voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING: Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A - Fuel Tank — Capacity of 1.3 U.S. gallons (5.0 L).

B - Circuit Breaker (AC) — A push-to-reset circuit breaker is

provided to protect the receptacle and generator against

electrical overload.

C - 120 Volt AC, 15 Amp, Duplex Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 15 Amp, single phase, 60 Hz electrical,

lighting, appliance, tool, and motor loads.

D - 12 Volt DC Receptacle — Use this receptacle with

battery charge cables to charge a 12 Volt battery. This

receptacle is protected by an auto reset circuit breaker.

E - Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

F - Choke Lever — Used when starting a cold engine.

G - Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

H - Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

J - Oil Fill Cap — Check and add engine oil here.

K - Engine Switch — Set this switch to “On” before using

recoil starter. Set switch to “Off” to stop engine.

L - Fuel Valve — Used to turn fuel supply on and off to

engine.

M - Recoil Starter — Used to start the engine manually.

Items Not Shown:

Identification Label — Provides model, revision, and serial

number of generator. Please have these readily available

when calling for assistance.

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded extension

cords with the generator’s 120 Volt duplex receptacle.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use

them. Extension cord sets used should be rated for 125 Volt

AC loads at 15 Amps or greater for most electrical devices.

Some devices, however, may not require this type of

extension cord. Check the operator’s manuals of those

devices for the manufacturer’s recommendations.

Keep extension cords as short as possible to minimize

voltage drop.

120 Volt AC, 15 Amp, Duplex Receptacle

The duplex receptacle is protected against overload by a

push-to-reset circuit breaker.

Use receptacle to operate 120 Volt AC, single–phase, 60 Hz

electrical loads requiring up to 1,800 watts (1.8 kW) at 15

Amps of current. Use cord sets that are rated for 125 Volt

AC loads at 15 Amps (or greater).

NOTICE:

Receptacles may be marked with rating value

greater than generator output capacity.

• NEVER attempt to power a device requiring more amperage than

generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload Generator.

12 Volt DC Receptacle

The maximum current available for the battery charge circuit

is 10 Amps. An automatic DC circuit breaker protects this

receptacle from overloads and assures the battery gets

recharged. If an overload occurs, the circuit breaker will trip.

After it cools, it will automatically reset itself.

This receptacle allows you to recharge a 12 Volt automotive

or utility style storage battery with the battery charge cable

provided.

This receptacle can not be used to crank an engine having a

discharged battery. See Charging a Battery before attempting

to recharge a battery.

NOTE: When the battery charge circuit is in use, the AC

capacity is reduced by 120 watts. Make sure the combined

load is within the rated limits.

WARNING:

Overloaded electrical cords can overheat,

arc, and burn resulting in death, bodily injury,

and/or property damage.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate the unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn fuel valve (A) to “On” position (fully

counterclockwise).

3. Place the engine switch (B) in the “On” position.

4. Start engine according to instructions given in the

engine operator’s manual.

NOTE: If engine starts after 3 pulls, but fails to run for more

than 10 seconds, check for proper oil level in crankcase. This

unit may be equipped with a low oil protection device. See

engine operator’s manual.

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few minutes

after starting.

2. Plug in and turn on the desired 120 Volt AC, single

phase, 60 Hz electrical loads.

NOTE:

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacle.

• DO NOT connect 3-phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See Don’t

Overload Generator.

NOTICE:

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned ON.

2. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

3. Move engine switch to the “Off” position.

4. Turn the fuel valve to the “Off” position (fully

clockwise).

WARNING: Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING: Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

Charging a Battery

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery.

NOTICE:

• Not for use with any other type of battery.

• DO NOT use the unit to charge any 6 Volt batteries.

• DO NOT use the unit to crank an engine having a

discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. If necessary, clean battery posts or terminals.

2. Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

3. If the battery is equipped with vent caps, make sure

they are installed and are tight.

4. Connect battery charge cable clamp with red handle to

battery post or terminal indicated by Positive, POS or (+).

5. Connect battery charge cable clamp with black handle

to battery post or terminal indicated by Negative, NEG,

or (–).

6. Connect battery charge cable connector plug to the

12 Volt DC panel receptacle.

7. Start generator as described in Starting The Engine. Let

the engine run while battery recharges.

NOTE: Normally a period of 30 to 120 minutes is sufficient to

recharge a weak battery.

8. When battery has charged, shut down engine as

described in Stopping The Engine.

9. Remove the battery charging cable from the generator

and then disconnect from the battery posts.

NOTE: Use an automotive hydrometer to test battery state of

charge and condition. Follow the hydrometer manufacturer’s

instructions carefully. Generally, a battery is considered to be

at 100% state of charge when specific gravity of its fluid (as

measured by hydrometer) is 1.260 or higher.

Cold Weather Operation

Under certain weather conditions (temperatures below 40°F

[4°C] combined with high humidity), your generator may

experience icing of the carburetor and/or the crankcase

breather system. To reduce this problem, you need to

perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil (synthetic preferred, see engine

operator’s manual).

4. Check oil level daily or after every eight (8) hours of

operation.

5. Maintain generator following maintenance schedule in

engine operator’s manual.

6. Shelter unit from elements.

Positive

Negative

WARNING:

Battery posts, terminals and related

accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

WARNING:

Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for a

long time after battery has been charged.

Slightest spark will ignite hydrogen and cause explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is extremely

caustic.

Contact with battery fluid will cause severe chemical burns.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

• DO NOT continue to charge a battery that becomes hot or is

fully charged.

• DO NOT leave battery unattended.

Creating a Temporary Cold Weather Shelter

1. For temporary shelter, the original shipping carton can

be used.

2. Cut off top carton flaps and one long side of carton to

expose muffler side of unit. If required, tape up other

sides of carton to fit over generator as shown.

3. Cut appropriate slots to access receptacles of unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section Generator

Location. Keep exhaust gas from entering a confined

area through windows, doors, ventilation intakes or

other openings.

6. Start generator as described in the section Starting the

Engine, then place carton over generator. Keep at least

5 ft. (1.5 m) clearance on all sides of generator

including overhead with shelter in place.

7. Remove shelter when temperatures are above 40°F

[4°C].

8. Turn engine OFF and let cool two (2) minutes before

refueling. Let any spilled fuel evaporate before starting

engine.

Building a Cold Weather Shelter

1. Using non combustible material with a fire rating of at

least one hour, build a shelter that will enclose three

sides and the top of the generator. Make sure muffler

side of generator is exposed.

NOTE: Contact your local building material supplier for non

combustible materials with a fire rating of at least one hour.

IMPORTANT: Be sure shelter can easily be repositioned for

change in wind direction.

2. DO NOT enclose generator any more than shown.

Shelter should hold enough heat created by the

generator to prevent icing problem.

3. Follow steps 3 through 8 as described previously in

Creating a Temporary Cold Weather Shelter.

Wind

WARNING: Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

(even if windows and doors are open), including the generator

compartment of a recreational vehicle (RV).

WARNING: Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

Don’t Overload Generator

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is

the amount of power your generator must produce to

keep your items running. See Wattage Reference Guide.

3. Estimate how many surge (starting) watts you will need.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 1555

Highest Additional Surge Watts = 600

Total Generator Output Required = 2155

Power Management

To prolong the life of your generator and attached devices, it

is important to take care when adding electrical loads to your

generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity, as

described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Fan 300 600

Deep Freezer 500 500

Television 500 —

Security System 180 —

Light (75 Watts) 75 —

1555 Total

Running Watts

600 Highest

Surge Watts

Wattage Reference Guide

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 —

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 cf 800 1600

Water Well Pump - 1/3 hp 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 hp 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 —

Coffee Maker 1500 —

Electric Stove - Single Element 1500 —

Hot Plate 2500 —

Family Room

DVD/CD Player 100 —

VCR 100 —

Stereo Receiver 450 —

Color Television - 27 in 500 —

Personal Computer w/17 in

monitor

800 —

Other

Security System 180 —

AM/FM Clock Radio 300 —

Garage Door Opener - 1/2 hp 480 520

Electric Water Heater - 40 gallon 4000 —

DIY/Job Site

Quartz Halogen Work Light 1000 —

Airless Sprayer - 1/3 hp 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 hp 1000 1000

Circular Saw - 7-1/4 in 1500 1500

Miter Saw - 10 in 1800 1800

Table Planer - 6 in 1800 1800

Table Saw/Radial Arm Saw - 10 in 2000 2000

Air Compressor - 1-1/2 hp 2500 2500

Maintenance

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See an authorized dealer for

service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

generator as instructed in this manual and the engine

operator’s manual.

NOTE: Should you have questions about replacing

components on your generator, please call (877) 370-7501

for assistance.

• Some adjustments will need to be made periodically to

properly maintain your generator.

• All maintenance in this manual and the engine

operator’s manual should be made at least once each

season.

• Once a year you should clean or replace the spark plug,

clean or replace the air filter. A new spark plug and

clean air filter assure proper fuel-air mixture and help

your engine run better and last longer. Please refer to

your engine operator’s manual for more details.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive dust,

dirt, moisture, or any corrosive vapors. Cooling air slots in

the generator must not become clogged with snow, leaves,

or any other foreign material.

NOTE: DO NOT use water or other liquids to clean generator.

Liquids can enter engine fuel system, causing poor

performance and/or failure to occur. In addition, if liquid

enters generator through cooling air slots, some of the liquid

will be retained in voids and cracks of the rotor and stator

winding insulation. Liquid and dirt buildup on the generator

internal windings will eventually decrease the insulation

resistance of these windings.

Cleaning

Daily or before use, look around and underneath the

generator for signs of oil or fuel leaks. Clean accumulated

debris from inside and outside the generator. Keep the

linkage, spring and other engine controls clean. Inspect

cooling air slots and openings on generator. These openings

must be kept clean and unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE:

Improper treatment of generator can damage it

and shorten its life.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for

damage or carbon blockage. If replacement parts are

required, make sure to use only original equipment

replacement parts.

Clean and inspect the spark arrester every 50 hours of

operation as follows:

1. To remove muffler guard (A), remove four screws (B)

that connect guard to generator.

2. Remove four screws (C) that attach spark arrester

screen (D) to muffler. Pull the plate with the screen

attached.

WARNING: Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

3. Inspect screen and obtain a replacement if torn,

perforated or otherwise damaged. DO NOT use a

defective screen. If screen is not damaged, clean it with

a brush.

4. Reattach screen making sure gasket is in place.

Reattach muffler guard.

Engine Maintenance

See the engine operator’s manual for instructions on how to

properly maintain the engine.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Storage

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot be

done and you must store the unit for more than 30 days, use

the following guidelines to prepare it for storage.

Generator Storage

• Clean the generator as outlined in Cleaning.

• Check that cooling air slots and openings on generator

are open and unobstructed.

Long Term Storage Instructions

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton FRESH START® fuel stabilizer, available as a

liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can then be stored up to

24 months.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container. Run

the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to

maintain freshness.

Storing the Engine

See the engine operator’s manual for instructions on how to

properly prepare the engine for storage.

Other Storage Tips

1. DO NOT store fuel from one season to another unless it

has been treated as described in Long Term Storage

Instructions.

2. Replace fuel container if it starts to rust. Rust and/or

dirt in fuel can cause problems if it’s used with this

unit.

3. Cover unit with a suitable protective cover that does not

retain moisture.

4. Store generator in clean, dry area.

WARNING: Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers

or other appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

WHEN DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Drain fuel tank outdoors.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WARNING:

Storage covers can be flammable.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the cover

on the equipment.

CAUTION: Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Troubleshooting

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact authorized service facility.

3. Check and repair.

4. Connect another device that is in good

condition.

Engine runs good at no-load but

“bogs down” when loads are

connected.

1. Short circuit in a connected load.

2. Engine speed is too slow.

3. Generator is overloaded.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. Contact authorized service facility.

3. See Don’t Overload Generator in

Operation section.

4. Contact authorized service facility.

Engine will not start; or starts

and runs rough.

1. Rocker switch set to “Off”.

2. Fuel Valve is in “Off” position.

3. Dirty air cleaner.

4. Out of fuel.

5. Stale fuel.

6. Spark plug wire not connected to spark

plug.

7. Bad spark plug.

8. Water in fuel.

9. Flooded.

10. Excessively rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Set switch to “On”.

2. Turn fuel valve to “Open” position.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Drain fuel tank and carburetor; fill with

fresh fuel.

6. Connect wire to spark plug.

7. Replace spark plug.

8. Drain fuel tank and carburetor; fill with

fresh fuel.

9. Wait 5 minutes and re-crank engine.

10. Contact authorized service facility.

11. Contact authorized service facility.

12. Contact authorized service facility.

Engine shuts down when

running.

Out of fuel. Fill fuel tank.

Engine lacks power.

1. Load is too high.

2. Dirty air filter.

1. See Don’t Overload Generator in

Operation section.

2. Replace air filter.

Engine “hunts” or falters. Carburetor is running too rich or too lean. Contact authorized service facility.

Wiring Diagram

1919

Husky® PORTABLE GENERATOR OWNER WARRANTY POLICY

LIMITED WARRANTY

Husky® is a registered trademark of The Home Depot. Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of

the portable generator that is defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under

this warranty must be borne by purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service,

find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you

may also have other rights which vary from state to state or country to country.

3 years*

1 year

Consumer Use

Commercial Use

The warranty period begins on the date of purchase by the first retail end user, and continues for the period of time stated above. “Consumer" means

personal residential household use by a retail consumer. All other uses are considered “Commercial”. Once equipment has experienced commercial use, it

shall thereafter be considered as commercial use for purposes of this warranty.

This warranty excludes the engine. For engine warranty questions, call Robin America, Inc. at (800) 277-6246 or visit www.subarupower.com for a

dealer locator.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the portable generator has been removed or the equipment has been altered or modified.

During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under

normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or

alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,

to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, fuel system

cleaning and obstruction (due to chemical, dirt, carbon, lime, and so forth).

• Other Exclusions: This warranty also excludes wear items such as o-rings, filters, etc., or malfunctions resulting from accidents, abuse, modifications,

alterations, or improper servicing or freezing or chemical deterioration. Accessory parts such as starting batteries, generator adapter cord sets and

storage covers are excluded from the product warranty. This warranty excludes used, reconditioned, and demonstration equipment, equipment used

for prime power in place of utility power, equipment used in life support applications, and failures due to acts of God and other force majeure events

beyond the manufacturers control. 208621E, Rev. -, 10/1/2008

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective October 1, 2008 replaces all undated Warranties and all Warranties dated before October 1, 2008

*Years 2 & 3 parts only

WARRANTY PERIOD