Style Selections SSDR4872CLSV Guide d'installation

Marque: Style Selections

Modèle: SSDR4872CLSV

Taper: Guide d'installation

FRAMELESS DOOR

ITEM #0954412, 0954410

MODEL #SSDR4872CLSV, SSDR6072CLSV

AB1807

Serial Number

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

Français p. 17

Español p. 33

Purchase Date

PART DESCRIPTION QUANTITY

A Fixed Panel Jamb 1

B Gasket 1

C Fixed Panel 1

D Door Vinyl Strip Side 1

E Door Panel 1

F Top Rail 1

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

G Magnet Seal (Door) 1

H Magnet Seal (Jamb) 1

I Door Jamb 1

J Threshold Vinyl Strip 1

K Threshold 1

HARDWARE CONTENTS (Note: Hardware not shown to size)

Aluminum Cap

Qty. 1

1-9/16 in. Screw

Qty. 8

Wall Anchor

Qty. 11

Track Nut

Qty. 2

Screw Guide

Qty. 2

Track Screw

Qty. 2

Top Roller Assembly

Qty. 2

Wall Bracket

Qty. 1

Wall Bracket Cover

Qty. 1

Rail Cap

Qty. 1

Roller Bumper

Qty. 1

Anti-jumper Assembly

Qty. 2

1-3/4 in. Screw

Qty. 3

Handle

Qty. 1

Door Guide

Qty. 1

Hex Key

Qty. 1

HARDWARE CONTENTS (Note: Hardware not shown to size)

Spacer

Qty. 2

Spanner

Qty. 2

Threshold Cover

Qty. 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

WARNING

Safety glasses should be worn at all times during installation.

CAUTION

Two people are required to lift glass panel during installation. It is heavy and will break if dropped.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to

assemble the product.

Estimated Assembly Time: 90 minutes

Tools Required for Assembly (not included): Silicone caulk, caulk gun, drill, 1/4 in. drill bit, 1/8 in. drill

bit, measure tape, utility knife, level, pencil, Phillips screwdriver, handsaw, and safety glasses.

PRE-INSTALLATION

Before starting installation, determine if door panel (E) will be installed with left or right opening. Door

guide (OO) is designed to be used for either installation. Follow conversion guide below according to

door opening. Set aside for use in step 11 on page 11.

Follow steps below to convert right

hand door opening to left hand

door opening.

Follow steps below to convert left

hand door opening to right hand

door opening.

OO OO

ASSEMBLY INSTRUCTIONS

Note: Instructions show right-side installation. Reverse for left-side installation.

IMPORTANT NOTE: If installing the optional return panel (Item #0954411, 0954409, sold

separately), please rst refer to the instruction manual included with the return panel. Once

you are nished following the instructions for the return panel, proceed to Step 6 in these

instructions to complete assembly.

1. Set xed panel jamb (A) on shower base

threshold. Use a level to ensure panel jamb (A)

is level. Using a pencil (not included), mark the

four pre-drilled hole locations. Remove panel

jamb (A). Using a drill (not included), drill holes

approximately 1-1/2 in. deep into each marking.

NOTE: If installing into tile, use 1/4 in. masonry

bit (not included) and proceed to step 2a. If

installing into an acrylic or berglass shower

enclosure, use 1/8 in. drill bit (not included) and

proceed to step 2b.

2a. Tile installation: Insert wall anchors (CC) into

each drilled hole using rubber mallet (not

included). Place xed panel jamb (A) back into

place. Tighten 1-9/16 in. screws (BB) with

Phillips screwdriver (not included) into each

wall anchor (CC).

Hardware Used

Wall Anchor

1-9/16 in. Screw

x 4

2b. Acrylic and berglass installation: Place

xed panel jamb (A) back into place. Tighten

1-9/16 in. screws (BB) with Phillips screwdriver

into each drilled hole.

Hardware Used

1-9/16 in. Screw

x 4

ASSEMBLY INSTRUCTIONS

3. Insert xed panel (C) into xed panel jamb (A)

slot, making sure that the xed panel (C) is level.

If xed panel (C) is not level, install spacers

(QQ) on bottom as needed. Starting at the

bottom, place gasket (B) inside shower between

xed panel (C) and xed panel jamb (A). Using a

knife, cut remaining gasket (B) on top.

Top

View

4. Insert rail cap (JJ) on left side of top rail (F) and

wall bracket cover (II) on the right side. Insert

track nut (DD) and screw guide (EE) into both

front holes on top rail (F).

Hardware Used

x 2

Hardware Used

Spacer

x 2

Track Nut

x 2

Screw Guide

x 1

Wall Bracket Cover

x 1

Rail Cap

ASSEMBLY INSTRUCTIONS

5. Install top rail (F) to xed panel (C) by inserting

screw guides (EE) into both pre-drilled holes.

Install track screws (FF) into each hole

connecting the top rail to xed panel (C). Install

roller bumper (KK) on top rail (F). Hand tighten

roller bumper (KK) with hex key (PP).

CFF

Hardware Used

x 2

Track Screw

x 1

Roller Bumper

x 1

Hex Key

6. Place top rail (F) to right side of wall. Ensure

top rail is level. Using a pencil, trace around the

wall bracket cover (II). Place wall bracket (HH) in

middle of traced line. Using a pencil, mark each

hole.

NOTE: If installing into tile, proceed to step 7a.

If installing into an acrylic or berglass shower

enclosure, proceed to step 7b.

Hardware Used

x 1

Wall Bracket Cover

x 1

Wall Bracket

NOTE: If you have installed the optional return panel (Item #0954411, 0954409, sold

separately), start here at Step 6 to complete assembly.

ASSEMBLY INSTRUCTIONS

7a. Tile installation: Drill hole locations on wall

using a drill and 1/4 in. masonry bit. Using a rubber

mallet, insert wall anchors (CC) into each hole.

Using a Phillips screwdriver, install wall bracket

(HH) into wall using 1-3/4 in. screws (LL). Place top

rail (F) and wall bracket cover (II) into wall bracket

(HH). Hand tighten wall bracket cover (II) into place

using hex key (PP) on both top and bottom. Check

to make sure top rail is level. Hand tighten both

track screws (FF) using hex key (PP).

Hardware Used

Wall Anchor

Wall Bracket

Cover

1-3/4 in.

Screw

Hex Key

x 1

x 2

x 1

7b. Acrylic and berglass installation: Drill hole

locations on wall using a drill and 1/8 in. bit. Using

a Phillips screwdriver, install wall bracket (HH) into

wall using 1-3/4 in. screws (LL). Hand tighten wall

bracket cover (II) into place using hex key (PP) on

both top and bottom. Check to make sure top rail

is level. Hand tighten both track screws (FF) using

hex key (PP).

Hardware Used

Wall Bracket

Cover

1-3/4 in.

Screw

Hex Key

x 1

8. Insert door vinyl strip (D) on left side of door

panel (E). Insert magnet seal (door) (G) on

opposite side. Using hex key (PP), install

handle (NN) into pre-drilled holes on door panel

(E). Install top rollers (GG) into top pre-drilled

holes on door panel (E). Use spanner (RR)

to hold nut in place while installing top rollers

(GG).

ASSEMBLY INSTRUCTIONS

9. Lift assembled door panel (E) and place top

rollers (GG) onto top rail (F).

Hardware Used

Top Roller

Handle

Hex Key

Spanner

x 1

x 2

x 1

10. Install anti-jumper assembly (MM) into each

pre-drilled hole on door panel located right

below top rail (F).

Hardware Used

Anti-jumper

Assembly

x 2

ASSEMBLY INSTRUCTIONS

11. Insert door guide (OO) into xed panel (C) on

front slot. Using a pencil, mark door guide (OO)

hole onto shower base threshold. Remove door

guide (OO). Drill hole on mark using 1/8 in. drill

bit. Using Phillips screwdriver, secure door guide

to shower base threshold with 1-3/4 in. screw

(LL).

12. Measure opening between door guide (OO)

and side wall of shower. This will be your Y

measurement. Insert threshold cover (SS) onto

right side of threshold (K). Use Y measurement

to cut left side of threshold (K) with hacksaw

(not included). Use Y measurement to cut

left side of threshold vinyl strip (J) with utility

knife (not included). Measure from left side of

threshold (K) to threshold cover (SS). This will

be your X measurement. Use X measurement

to cut notch on right side of threshold vinyl strip

(J). NOTE: When cutting threshold vinyl strip (J)

with X measurement, do not cut ap.

Hardware Used

Door Guide

x 1

1-3/4 in. Screw

x 1

Threshold Cover

x 1

ASSEMBLY INSTRUCTIONS

14. Apply silicone caulk to bottom of threshold (K).

Install threshold (K) between door guide (OO)

and shower wall. Slide door panel (E) into top

door guide.

15. Slide door panel (E) against shower wall.

Magnet seal (door) (G) must be resting against

shower wall. Using a pencil, trace entire location

around magnet seal (door) (G).

Top

View

13. Slide threshold vinyl strip (J) into threshold (K).

Apply silicone caulk to inside of threshold cover

(SS). Slide into right side of threshold (K). Make

sure the ap on the threshold vinyl strip (J)

covers threshold cover (SS).

Hardware Used

Threshold Cover

x 1

ASSEMBLY INSTRUCTIONS

17a

17b

17a. Tile installation: Insert wall anchors (CC) into

each drilled hole using rubber mallet. Place

door jamb (I) back into place. Tighten 1-9/16

in. screws (BB) with Phillips screwdriver into

each wall anchor (CC).

17b. Acrylic and berglass installation: Place

door jamb (I) back into place. Tighten 1-9/16

in. screws (BB) with Phillips screwdriver into

each drilled hole.

16. Set door jamb (I) in middle of traced line. Ensure

door jamb (I) is level. Using a pencil, mark the

four pre-drilled hole locations. Remove door

jamb (I). Using a drill (not included), drill holes

approximately 1-1/2 in. deep into each marking.

NOTE: If installing into tile, use 1/4 in. masonry

bit and proceed to step 17a. If installing into an

acrylic or berglass shower enclosure, use 1/8

in. drill bit and proceed to step 17b.

Hardware Used

Wall Anchor

1-9/16 in. Screw

x 4

Hardware Used

1-9/16 in. Screw

x 4

ASSEMBLY INSTRUCTIONS

19. Move door panel (E) to closed position. Door

(E) should be fully ush with magnet seal (jamb)

(H). If door (E) is uneven, remove cap on back

of right top roller (GG). Use spanners (RR) to

adjust angle of door until fully ush with magnet

seal (jamb) (H).

20. Caulk both vertical and bottom seams. Place

aluminum cap (AA) on top left corner of door.

Allow 24 hours for caulk to dry before using.

Hardware Used

18. Slide magnet seal (jamb) (H) over door jamb (I).

Spanner

x 1

Aluminum Cap

x 1

The distributor warrants to the original purchaser that this xture will be free of manufacturing defects,

which aect its performance as a bathing or showering xture, under the following conditions and

subject to the limitations contained in the ”Remedies” and ”Warranty Limitations” sections. The Limited

Warranty applies for 5 years from the date of purchase if the xture is used in a residential

owner-occupied building for non-commercial purposes or for 2 years from the date of purchase if it is

used in any other building, including any building used for rental, commercial or business purposes.

This Limited Warranty is void if the xture is not installed in accordance with the installation instructions

supplied by the distributor, or local building codes and ordinances, or if the care and cleaning

instructions supplied by the distributor are not followed. This Limited Warranty is also void if the xture

is moved from the location of its initial installation, or is subjected to accident, abuse, or misuse. The

Limited Warranty excludes normal wear and tear. This Limited Warranty shall be void unless any

failure or non-conformance is discovered before the expiration of this warranty, and is reported to

the distributor, in writing, accompanied by the original proof of purchase, within 30 days of discovery.

REMEDIES — The original purchaser’s remedy under this Limited Warranty is limited to the repair,

replacement or refund of the purchase price of the xture, at the distributor's sole option, of any part of

the xture that has failed or does not conform to the manufacturer’s specications. In no event shall the

distributor be liable for lost prots, loss of use, incidental, special or consequential damages including,

but not limited to, damage to or loss of use of the building or its contents, arising out of any defect in

the xture nor shall the distributor be liable for any amount in excess of the original purchase price

of the xture. The distributor reserves the right to require the return, at purchaser’s expense, of the

damaged xture for repair or exchange before providing services under this Limited Warranty. If the

distributor elects to replace the xture, its obligation is limited to supplying a replacement unit or

component part of comparable size and style, and does not include the cost of removal, installation or

transportation, which must be borne by the purchaser. Replacement parts provided under this Limited

Warranty are warranted for the remainder of the original warranty period applicable to the xture, as

if such parts were original components of that xture. WARRANTY LIMITATIONS — THERE ARE

NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF

IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. THE DISTRIBUTOR DISCLAIMS

ANY AND ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow limitations of incidental or consequential damages, so the above limitations

and exclusions may not apply to you. In such states, the distributors' liability shall be limited to

the extent permitted by state law. ANY IMPLIED WARRANTIES ARISING BY WAY OF STATE

LAW, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION

AND IN SCOPE OF COVERAGE TO THE TERMS OF THIS LIMITED WARRANTY, UNLESS A

SHORTER PERIOD IS ALLOWED BY LAW.

WARRANTY

Printed in China

CARE AND MAINTENANCE

• Do not use abrasive cleaners or metal scrapers.

• Use a squeegee after each use to prevent water spotting.

• Use any non-ammonia based glass cleaner.

PORTE SANS CADRE

ARTICLE #0954412, 0954410

MODÈLE #SSDR4872CLSV, SSDR6072CLSV

Numéro de série

Des questions, des problèmes, des pièces manquantes? Avant de retourner

l’article au détaillant, appelez notre service à la clientèle au 1 877 888-8225,

entre 8 h et 20 h (HNE), du lundi au vendredi.

JOIGNEZ VOTRE REÇU ICI

Date d’achat

PIÈCE DESCRIPTION QUANTITÉ

A Montant de panneau xe 1

B Joint 1

C Panneau xe 1

D Bande de vinyle latérale de la porte 1

E Panneau de porte 1

F Traverse supérieure 1

G Joint magnétique de la porte 1

H Joint magnétique du montant 1

I Montant de porte 1

J Bande de vinyle du seuil 1

K Seuil 1

CONTENU DE L’EMBALLAGE

QUINCAILLERIE INCLUSE (Remarque : La quincaillerie n’est pas illustrée à la grandeur réelle.)

Embout en

aluminium

Qté : 1

Vis de 1 9/16 po

Qté : 8

Cheville d’ancrage

Qté : 11

Écrou de traverse

Qté : 2

Guide-vis

Qté : 2

Vis de traverse

Qté : 2

Ensemble de roulette

supérieure

Qté : 2

Support mural

Qté : 1

Capuchon de

support mural

Qté : 1

Embout de traverse

Qté : 1

Butée de roulette

Qté : 1

Dispositif

antisoulèvement

Qté : 2

Vis de 1 3/4 po

Qté : 3

Poignée

Qté : 1

Guide de porte

Qté : 1

Clé hexagonale

Qté : 1

Espaceur

Qté : 2

Clé

Qté : 2

Embout de seuil

Qté : 1

QUINCAILLERIE INCLUSE (Remarque : La quincaillerie n’est pas illustrée à la grandeur réelle.)

La page charge ...

Style Selections SSDR4872CLSV Guide d'installation

Marque: Style Selections

Modèle: SSDR4872CLSV

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Style Selections SSDR4872CLSV Installation guide
español: Style Selections SSDR4872CLSV Guía de instalación

Style Selections SSDR4872CLSV Guide d'installation

Style Selections SSDR4872CLSV Guide d'installation

dans d''autres langues

Documents connexes

Autres documents