Oracle MiniCluster S7-2 Manuel utilisateur

Taper
Manuel utilisateur
Oracle
®
MiniCluster S7-2 Service Manual
Part No: E76798-02
March 2017
Oracle MiniCluster S7-2 Service Manual
Part No: E76798-02
Copyright © 2016, 2017, Oracle and/or its affiliates. All rights reserved.
This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except
as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform,
publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is
prohibited.
The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.
If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:
U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,
delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental
regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the
hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.
This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous
applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all
appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this
software or hardware in dangerous applications.
Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.
Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of
SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered
trademark of The Open Group.
This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are
not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement
between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content,
products, or services, except as set forth in an applicable agreement between you and Oracle.
Access to Oracle Support
Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?
ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.
Référence: E76798-02
Copyright © 2016, 2017, Oracle et/ou ses affiliés. Tous droits réservés.
Ce logiciel et la documentation qui l'accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d'utilisation et
de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, accorder de licence, transmettre,
distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute
ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d'interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.
Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu'elles soient exemptes d'erreurs et vous
invite, le cas échéant, à lui en faire part par écrit.
Si ce logiciel, ou la documentation qui l'accompagne, est livré sous licence au Gouvernement des Etats-Unis, ou à quiconque qui aurait souscrit la licence de ce logiciel pour le
compte du Gouvernement des Etats-Unis, la notice suivante s'applique :
U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,
delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental
regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the
hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.
Ce logiciel ou matériel a été développé pour un usage général dans le cadre d'applications de gestion des informations. Ce logiciel ou matériel n'est pas conçu ni n'est destiné à être
utilisé dans des applications à risque, notamment dans des applications pouvant causer un risque de dommages corporels. Si vous utilisez ce logiciel ou ce matériel dans le cadre
d'applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans
des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l'utilisation de ce logiciel ou matériel pour des
applications dangereuses.
Oracle et Java sont des marques déposées d'Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d'autres propriétaires
qu'Oracle.
Intel et Intel Xeon sont des marques ou des marques déposées d'Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques
déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d'Advanced Micro Devices. UNIX est une
marque déposée de The Open Group.
Ce logiciel ou matériel et la documentation qui l'accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de
tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée
dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des
dommages causés par l'accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.
Accès aux services de support Oracle
Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/
pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.
Contents
Using This Documentation .................................................................................  7
Product Documentation Library .........................................................................  7
Feedback .......................................................................................................  7
Overview of System Status Indicators and LEDs ...............................................  9
Compute Node Status Indicators ........................................................................  9
Storage Array Front Panel and Drive Indicators .................................................... 9
Storage Array Back Panel Indicators ................................................................. 11
Preparing MiniCluster for Service .....................................................................  13
Detecting and Managing Faults ........................................................................ 13
Preparing MiniCluster For Service ...................................................................  14
Component Service Categories ........................................................................  14
Servicing CRUs That Do Not Require System Power Off ..................................  17
Compute Node Hot-Swappable Components ......................................................  17
Storage Array Hot-Swappable Components ........................................................ 18
Replacement Procedures .........................................................................  18
Servicing CRUs That Require Compute Node Power Off ..................................  31
Servicing Compute Node CRUs .......................................................................  31
Servicing FRUs .................................................................................................  33
Servicing Compute Node FRUs .......................................................................  33
Returning MiniCluster to Operation ..................................................................  35
Returning Compute Nodes to Operation ............................................................  35
5
Contents
Powering On MiniCluster ...............................................................................  35
Power On Procedure .........................................................................  36
Index .................................................................................................................. 37
6 Oracle MiniCluster S7-2 Service Manual • March 2017
Using This Documentation
Overview – Describes how to service Oracle's MiniCluster S7-2 hardware
Audience – System administrators and authorized service providers
Required knowledge – Advanced experience installing enterprise servers
Product Documentation Library
Documentation and resources for this product and related products are available at http://
docs.oracle.com/cd/E69469_01/.
Feedback
Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.
Using This Documentation 7
8 Oracle MiniCluster S7-2 Service Manual • March 2017
Overview of System Status Indicators and LEDs
This chapter describes system status indicators and LEDs.
“Compute Node Status Indicators” on page 9
“Storage Array Front Panel and Drive Indicators” on page 9
“Storage Array Back Panel Indicators” on page 11
Compute Node Status Indicators
These topics describe MiniCluster compute node status indicators (LEDs).
Note - The links below take you to topics outside of the MiniCluster library to the Oracle
SPARC S7-2 documentation library. Use your browser's Back button to return to the
MiniCluster library.
“Front Panel Components” in SPARC S7-2 Server Service Manual
“Rear Panel Components” in SPARC S7-2 Server Service Manual
Storage Array Front Panel and Drive Indicators
The following figure shows the controls and indicators on the storage array front panel and
drives.
Overview of System Status Indicators and LEDs 9
Storage Array Front Panel and Drive Indicators
Callout Indicator/LED: Color State Meaning
1 Locate: white Off – Normal operation.
Fast blink – This LED blinks to help locate the system. Operators
can turn this indicator on and off remotely using Oracle ILOM.
Pressing this button toggles the fast blink on or off.
2 Service Required: amber Off – Normal operation.
Steady on – A fault is present in the storage array.
3 OK: green On – The storage array is powered on and operating normally.
Off – The storage array is unplugged or turned off.
4 Power Supply fault indicator:
amber
On – Indicates a fault with a power supply. View the LEDs at the
back of the storage array to determine which power supply has
the fault.
Off – Normal operation.
5 SAS I/O Module fault indicator:
amber
Service Required – Lights amber to indicate a fault with an I/O
module. View the LEDs at the back of the storage array to determine
which module has the fault.
6 Ready-to-Remove: blue On – The storage drive can be safely removed during a hot-plug
operation.
Off – The storage drive has not been prepared for removal.
7 Drive Service Required: amber Off – Normal operation.
10 Oracle MiniCluster S7-2 Service Manual • March 2017
Storage Array Back Panel Indicators
Callout Indicator/LED: Color State Meaning
Steady on – A fault is present in the disk drive.
8 Power/Activity: green On – The drive is installed and recognized by the system but
there is no drive activity.
Blink – The LED blinks randomly in response to data being
written to or read from the drive.
Off – The drive is powered off or the installed drive is not
recognized by the system.
Storage Array Back Panel Indicators
The following figure shows the controls and indicators on the storage array back panel and
drives.
Callout Indicator/LED: Color State Meaning
1 AC power fault indicator: amber On – Indicates an AC power fault.
Off – Normal operation.
Overview of System Status Indicators and LEDs 11
Storage Array Back Panel Indicators
Callout Indicator/LED: Color State Meaning
2 Fan fail indicator: amber On – The fan is faulty.
Off – Normal operation.
3 Power supply status indicator:
green
On – The power supply is operating normally.
Off – The power supply is unplugged or turned off.
4 DC power fail indicator: amber On – The power supply is faulty.
Off – Normal operation.
5 Reserved This port is reserved for Oracle Service.
6 Network port (reserved) This port is reserved for Oracle Service.
7 Locate: white Off – Normal operation.
Fast blink – This LED blinks to help locate the system. Operators
can turn this indicator on and off remotely using Oracle ILOM.
Pressing this button toggles the fast blink on or off.
8 Service Required: amber Off – Normal operation.
Steady on – A fault is present in the storage array.
9 OK: green On – The storage array is powered on and operating normally.
Off – The storage array is unplugged or turned off.
10 SAS I/O Module Ready-to-
Remove: blue
On – The I/O module can be safely removed during a hot-plug
operation.
Off – The I/O module has not been prepared for removal.
11 SAS I/O Module fault indicator:
amber
Service Required – Lights amber to indicate a fault with an I/O
module.
12 SAS I/O Module OK: green On – The I/O module is powered on and operating normally.
Off – The I/O module is unplugged or turned off.
13 Host SAS port fault indicator:
amber
Service Required – Lights amber to indicate a fault with the port or
connection.
14 Host SAS port activity indicator:
green
Lights green to indicate host SAS link activity.
12 Oracle MiniCluster S7-2 Service Manual • March 2017
Preparing MiniCluster for Service
This chapter describes how to prepare MiniCluster for servicing.
“Detecting and Managing Faults” on page 13
“Preparing MiniCluster For Service” on page 14
“Component Service Categories” on page 14
Detecting and Managing Faults
Note - The links in the following list take you to instructions outside of the MiniCluster library
to the SPARC S7-2 documentation libraries. Use your browser's Back button to return to the
MiniCluster library.
“Checking for Faults” in SPARC S7-2 Server Service Manual
“Log In to Oracle ILOM (Service)” in SPARC S7-2 Server Service Manual
“Identify Faulted Components” in SPARC S7-2 Server Service Manual
“Performing Advanced Troubleshooting” in SPARC S7-2 Server Service Manual
“Check the Message Buffer” in SPARC S7-2 Server Service Manual
“View Log Files (Oracle Solaris)” in SPARC S7-2 Server Service Manual
“View Log Files (Oracle ILOM)” in SPARC S7-2 Server Service Manual
“POST Overview” in SPARC S7-2 Server Service Manual
“Configure POST” in SPARC S7-2 Server Service Manual
“Oracle ILOM Properties That Affect POST Behavior” in SPARC S7-2 Server Service
Manual
“Clear a Fault Manually” in SPARC S7-2 Server Service Manual
Preparing MiniCluster for Service 13
Preparing MiniCluster For Service
Preparing MiniCluster For Service
Most service procedures are performed on a single appliance component. Service procedures
that require a single compute node to be powered off can be performed without shutting down
the entire MiniCluster. Before powering off any component for service, refer to the Getting
Started Guide or Administration Guide for any special instructions or commands that must be
performed on the MiniCluster to prepare it for service.
Note - The links in the following list take you to instructions outside of the MiniCluster library
to the SPARC S7-2 documentation libraries. Use your browser's Back button to return to the
MiniCluster library.
“Safety Information” in SPARC S7-2 Server Service Manual
“Service Tools” in SPARC S7-2 Server Service Manual
“Find the Server Serial Number” in SPARC S7-2 Server Service Manual
“Locate the Server” in SPARC S7-2 Server Service Manual
“Prepare to Power Off the Server” in SPARC S7-2 Server Service Manual
“Power Off the Server” in SPARC S7-2 Server Service Manual
“Disconnect Cables From the Server” in SPARC S7-2 Server Service Manual
“Prevent ESD Damage” in SPARC S7-2 Server Service Manual
“Extend the Server to the Service Position” in SPARC S7-2 Server Service Manual
“Remove the Server From the Rack” in SPARC S7-2 Server Service Manual
“Open the Server Fan Door” in SPARC S7-2 Server Service Manual
“Remove the Top Cover” in SPARC S7-2 Server Service Manual
Component Service Categories
The server components and assemblies that can be replaced in the field fall into three
categories:
Hot-service, replaceable by customer
Cold-service, replaceable by customer
Cold-service, replaceable by authorized service personnel
Cold service procedures require that you shut the server down and unplug the power cables that
connect the power supplies to the power source.
14 Oracle MiniCluster S7-2 Service Manual • March 2017
Component Service Categories
Although hot service procedures can be performed while the server is running, you should
usually bring it to standby mode as the first step in the replacement procedure. See “Preparing
MiniCluster For Service” on page 14 for instructions.
This table identifies the components in each category.
Component Service
Category
Component Service Information
Hot-service, replaceable by
customer
Drives, compute node “Servicing Drives” in SPARC S7-2 Server Service Manual
Fan modules, compute node “Servicing Fan Modules” in SPARC S7-2 Server Service Manual
Power supplies, compute
node
“Servicing Power Supplies” in SPARC S7-2 Server Service Manual
HDD or SSD, storage array “Replace a Storage Array HDD or SSD (CRU) ” on page 18
Power supplies, storage
array
“Replace a Storage Array Power Supply (CRU)” on page 24
I/O module, storage array “Replace a Storage Array I/O Module (CRU)” on page 28
Cold-service, replaceable by
customer
DIMMs, compute node “Servicing DIMMs” in SPARC S7-2 Server Service Manual
Battery, compute node “Servicing the Battery” in SPARC S7-2 Server Service Manual
PCIe cards, compute node “Servicing PCIe Cards” in SPARC S7-2 Server Service Manual
Front indicator module,
compute node
“Servicing the Front Indicator Module” in SPARC S7-2 Server Service
Manual
eUSB drive, compute node “Servicing the eUSB Drive” in SPARC S7-2 Server Service Manual
Cold-service, replaceable by
authorized service personnel
Cables, compute node “Servicing Cables” in SPARC S7-2 Server Service Manual
Drive backplane, compute
node
“Servicing the Drive Backplane” in SPARC S7-2 Server Service Manual
Motherboard, compute node “Servicing the Motherboard” in SPARC S7-2 Server Service Manual
Preparing MiniCluster for Service 15
16 Oracle MiniCluster S7-2 Service Manual • March 2017
Servicing CRUs That Do Not Require System
Power Off
This chapter describes how to remove and replace the hot-swappable components in
MiniCluster. Hot-swappable means that these components can be replaced with the system
powered on.
Note - Hot-swappable components can also be replaced with the system powered off. If you
choose this method, first power off the system as described in “Preparing MiniCluster for
Service” on page 13.
The following topics are covered:
“Compute Node Hot-Swappable Components” on page 17
“Storage Array Hot-Swappable Components” on page 18
Compute Node Hot-Swappable Components
This section describes replacing hot-swappable components for the compute node.
Hot-swappable components are those that can be removed and installed while the system and
the compute nodes are running without requiring any administrative tasks. These are designated
as Customer Replaceable Units (CRUs).
Refer to the following table for hot-swap component instructions for your appliance.
Note - The links in the following table take you to instructions outside of the MiniCluster
library to the SPARC S7-2 documentation library. Use your browser's Back button to return to
the MiniCluster library.
“Servicing Drives” in SPARC S7-2 Server Service Manual
Servicing CRUs That Do Not Require System Power Off 17
Storage Array Hot-Swappable Components
“Servicing Fan Modules” in SPARC S7-2 Server Service Manual
“Servicing Power Supplies” in SPARC S7-2 Server Service Manual
Storage Array Hot-Swappable Components
This section describes replacing hot-swappable components for the storage array.
Hot-swappable components are those that can be removed and installed while the system and
the compute nodes are running without requiring any administrative tasks. These are designated
as Customer Replaceable Units (CRUs).
Caution - Data loss. Do not remove power from both power supplies of the storage array or
storage expansion shelf (if equipped) while the database is running. If you must power off the
storage array or expansion storage array, stop the database first.
Note - After a physical insertion or removal action of a storage array component (such as a disk
or SAS cable), you should wait before performing the next action to allow the system software
to fully process the event. This could take up to 3 minutes to complete.
Replacement Procedures
These storage array components can be replaced while the storage array is powered-on and
running:
“Replace a Storage Array HDD or SSD (CRU) ” on page 18
“Replace a Storage Array Power Supply (CRU)” on page 24
“Replace a Storage Array I/O Module (CRU)” on page 28
Replace a Storage Array HDD or SSD (CRU)
Use these procedures to replace a storage array HDD or SSD.
“Remove a Storage Array HDD or SSD (CRU)” on page 19
“Install a Storage Array HDD or SSD (CRU)” on page 22
18 Oracle MiniCluster S7-2 Service Manual • March 2017
Remove a Storage Array HDD or SSD (CRU)
Remove a Storage Array HDD or SSD (CRU)
1.
Enter the appropriate commands through the CLI to prepare the drive for
removal from the storage array.
Use this procedure to logically remove a storage array drive from the system before you
physically remove the drive.
The length of time that it takes to complete this procedure before you can physically remove the
drive depends on the type of drive you are removing:
SSD – The detach operation completes quickly and the drive can be removed immediately.
HDD – The detach operation takes several minutes to complete. Do not remove the drive
before the detach operation competes.
a.
Log into the mcmu CLI as a primary admin such as mcinstall.
% ssh mcinstall@minicluster_node_name_or_IPaddress
where minicluster_node_name_or_IPaddress is the name of the first node on MiniCluster,
or the IP address of the first node.
For example:
% ssh mcinstall@mc4-n1
b.
When prompted, enter the password.
For more information about running mcmu CLI commands, refer to the Oracle MiniCluster
S7-2 Installation Guide or the Oracle MiniCluster S7-2 Administration Guide.
c.
Identify the drive name.
You might be able to get the drive name from the error message or log file that led to the
plan to replace the drive.
You can use a command such as diskinfo. Make note of the long drive name (such as
c0t5000CCA23B0BF34Cd0) for use with this procedure. Also make note of the shorter name
(such as HDD8) for use with the followup task when you reattach the replaced drive.
Also note that the storage array drives are identified by a JBODARRAY string.
For example:
% diskinfo
D:devchassis-path c:occupant-compdev
---------------------------------- ---------------------
/dev/chassis/SYS/HDD0/disk c0t5000CCA02D1EE2A8d0
/dev/chassis/SYS/HDD1/disk c0t5000CCA02D1E7AACd0
Servicing CRUs That Do Not Require System Power Off 19
Remove a Storage Array HDD or SSD (CRU)
/dev/chassis/SYS/HDD2/disk c0t5000CCA02D1EDCECd0
/dev/chassis/SYS/HDD3/disk c0t5000CCA02D1ED360d0
/dev/chassis/SYS/HDD4/disk c0t5000CCA02D1EE6D8d0
/dev/chassis/SYS/HDD5/disk c0t5000CCA02D1EE6CCd0
/dev/chassis/SYS/HDD6 -
/dev/chassis/SYS/HDD7 -
/dev/chassis/SYS/MB/EUSB-DISK/disk c1t0d0
/dev/chassis/JBODARRAY1/HDD0/disk c0t5000CCA25497267Cd0
/dev/chassis/JBODARRAY1/HDD1/disk c0t5000CCA2549732B8d0
/dev/chassis/JBODARRAY1/HDD2/disk c0t5000CCA254974F28d0
/dev/chassis/JBODARRAY1/HDD3/disk c0t5000CCA254965A78d0
/dev/chassis/JBODARRAY1/HDD4/disk c0t5000CCA254978510d0
/dev/chassis/JBODARRAY1/HDD5/disk c0t5000CCA254964E3Cd0
/dev/chassis/JBODARRAY1/HDD6/disk c0t5000CCA0536CA5E4d0
/dev/chassis/JBODARRAY1/HDD7/disk c0t5000CCA0536CA7B0d0
/dev/chassis/JBODARRAY1/HDD8/disk c0t5000CCA23B0BF34Cd0
/dev/chassis/JBODARRAY1/HDD9/disk c0t5000CCA0536CB828d0
/dev/chassis/JBODARRAY1/HDD10/disk c0t5000CCA0536CB308d0
/dev/chassis/JBODARRAY1/HDD11/disk c0t5000CCA0536CAF2Cd0
/dev/chassis/JBODARRAY1/HDD12/disk c0t5000CCA0536CABE4d0
/dev/chassis/JBODARRAY1/HDD13/disk c0t5000CCA0536CB684d0
/dev/chassis/JBODARRAY1/HDD14/disk c0t5000CCA0536CA870d0
/dev/chassis/JBODARRAY1/HDD15/disk c0t5000CCA0536CAB88d0
/dev/chassis/JBODARRAY1/HDD16/disk c0t5000CCA0536CA754d0
/dev/chassis/JBODARRAY1/HDD17/disk c0t5000CCA0536CAD10d0
/dev/chassis/JBODARRAY1/HDD18/disk c0t5000CCA0536CAEF8d0
/dev/chassis/JBODARRAY1/HDD19/disk c0t5000CCA0536CA83Cd0
/dev/chassis/JBODARRAY1/HDD20/disk c0t5000CCA04EB272E8d0
/dev/chassis/JBODARRAY1/HDD21/disk c0t5000CCA04EB27234d0
/dev/chassis/JBODARRAY1/HDD22/disk c0t5000CCA04EB27428d0
/dev/chassis/JBODARRAY1/HDD23/disk c0t5000CCA04EB272A0d0
d.
Use this syntax to detach the disk prior to removing the disk:
% mcmu diskutil -d diskname
where diskname is the disk identifier of the drive you plan to remove.
For example:
% mcmu diskutil -d c0t5000CCA23B0BF34Cd0
.
<output omitted>
.
INFO:MCMU.controllers.common.pexpect_util:su to user oracle successfully.
[INFO ] logged into the zone f18-vm1-mc5qt-n1 as oracle
[INFO ] disk alias found to be RECO_0003
[INFO ] dropping disk c0t5000CCA23B0BF34Cd0s1
20 Oracle MiniCluster S7-2 Service Manual • March 2017
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Oracle MiniCluster S7-2 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues