Oracle MiniCluster S7-2 Manuel utilisateur

Marque: Oracle

Modèle: MiniCluster S7-2

Taper: Manuel utilisateur

Oracle

MiniCluster S7-2 Service Manual

Part No: E76798-02

March 2017

Oracle MiniCluster S7-2 Service Manual

Part No: E76798-02

This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except

as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform,

publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is

prohibited.

The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.

If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous

applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all

appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this

software or hardware in dangerous applications.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of

SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered

trademark of The Open Group.

This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are

not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement

between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content,

products, or services, except as set forth in an applicable agreement between you and Oracle.

Access to Oracle Support

Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?

ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.

Référence: E76798-02

Ce logiciel et la documentation qui l'accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d'utilisation et

de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, accorder de licence, transmettre,

distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute

ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d'interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.

Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu'elles soient exemptes d'erreurs et vous

invite, le cas échéant, à lui en faire part par écrit.

Si ce logiciel, ou la documentation qui l'accompagne, est livré sous licence au Gouvernement des Etats-Unis, ou à quiconque qui aurait souscrit la licence de ce logiciel pour le

compte du Gouvernement des Etats-Unis, la notice suivante s'applique :

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

Ce logiciel ou matériel a été développé pour un usage général dans le cadre d'applications de gestion des informations. Ce logiciel ou matériel n'est pas conçu ni n'est destiné à être

utilisé dans des applications à risque, notamment dans des applications pouvant causer un risque de dommages corporels. Si vous utilisez ce logiciel ou ce matériel dans le cadre

d'applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans

des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l'utilisation de ce logiciel ou matériel pour des

applications dangereuses.

Oracle et Java sont des marques déposées d'Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d'autres propriétaires

qu'Oracle.

Intel et Intel Xeon sont des marques ou des marques déposées d'Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques

déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d'Advanced Micro Devices. UNIX est une

marque déposée de The Open Group.

Ce logiciel ou matériel et la documentation qui l'accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de

tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée

dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des

dommages causés par l'accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.

Accès aux services de support Oracle

Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/

pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.

Contents

Using This Documentation ................................................................................. 7

Product Documentation Library ......................................................................... 7

Feedback ....................................................................................................... 7

Overview of System Status Indicators and LEDs ............................................... 9

Compute Node Status Indicators ........................................................................ 9

Storage Array Front Panel and Drive Indicators .................................................... 9

Storage Array Back Panel Indicators ................................................................. 11

Preparing MiniCluster for Service ..................................................................... 13

Detecting and Managing Faults ........................................................................ 13

Preparing MiniCluster For Service ................................................................... 14

Component Service Categories ........................................................................ 14

Servicing CRUs That Do Not Require System Power Off .................................. 17

Compute Node Hot-Swappable Components ...................................................... 17

Storage Array Hot-Swappable Components ........................................................ 18

Replacement Procedures ......................................................................... 18

Servicing CRUs That Require Compute Node Power Off .................................. 31

Servicing Compute Node CRUs ....................................................................... 31

Servicing FRUs ................................................................................................. 33

Servicing Compute Node FRUs ....................................................................... 33

Returning MiniCluster to Operation .................................................................. 35

Returning Compute Nodes to Operation ............................................................ 35

Contents

Powering On MiniCluster ............................................................................... 35

▼ Power On Procedure ......................................................................... 36

Index .................................................................................................................. 37

6 Oracle MiniCluster S7-2 Service Manual • March 2017

Using This Documentation

■

Overview – Describes how to service Oracle's MiniCluster S7-2 hardware

■

Audience – System administrators and authorized service providers

■

Required knowledge – Advanced experience installing enterprise servers

Product Documentation Library

Documentation and resources for this product and related products are available at http://

docs.oracle.com/cd/E69469_01/.

Feedback

Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.

Using This Documentation 7

8 Oracle MiniCluster S7-2 Service Manual • March 2017

Overview of System Status Indicators and LEDs

This chapter describes system status indicators and LEDs.

■

“Compute Node Status Indicators” on page 9

■

“Storage Array Front Panel and Drive Indicators” on page 9

■

“Storage Array Back Panel Indicators” on page 11

Compute Node Status Indicators

These topics describe MiniCluster compute node status indicators (LEDs).

Note - The links below take you to topics outside of the MiniCluster library to the Oracle

SPARC S7-2 documentation library. Use your browser's Back button to return to the

MiniCluster library.

■

“Front Panel Components” in SPARC S7-2 Server Service Manual

■

“Rear Panel Components” in SPARC S7-2 Server Service Manual

Storage Array Front Panel and Drive Indicators

The following figure shows the controls and indicators on the storage array front panel and

drives.

Overview of System Status Indicators and LEDs 9

Storage Array Front Panel and Drive Indicators

Callout Indicator/LED: Color State Meaning

1 Locate: white ■ Off – Normal operation.

■ Fast blink – This LED blinks to help locate the system. Operators

can turn this indicator on and off remotely using Oracle ILOM.

■ Pressing this button toggles the fast blink on or off.

2 Service Required: amber ■ Off – Normal operation.

■ Steady on – A fault is present in the storage array.

3 OK: green ■ On – The storage array is powered on and operating normally.

■ Off – The storage array is unplugged or turned off.

4 Power Supply fault indicator:

amber

■ On – Indicates a fault with a power supply. View the LEDs at the

back of the storage array to determine which power supply has

the fault.

■ Off – Normal operation.

5 SAS I/O Module fault indicator:

amber

Service Required – Lights amber to indicate a fault with an I/O

module. View the LEDs at the back of the storage array to determine

which module has the fault.

6 Ready-to-Remove: blue ■ On – The storage drive can be safely removed during a hot-plug

operation.

■ Off – The storage drive has not been prepared for removal.

7 Drive Service Required: amber ■ Off – Normal operation.

10 Oracle MiniCluster S7-2 Service Manual • March 2017

Storage Array Back Panel Indicators

Callout Indicator/LED: Color State Meaning

■ Steady on – A fault is present in the disk drive.

8 Power/Activity: green ■ On – The drive is installed and recognized by the system but

there is no drive activity.

■ Blink – The LED blinks randomly in response to data being

written to or read from the drive.

■ Off – The drive is powered off or the installed drive is not

recognized by the system.

Storage Array Back Panel Indicators

The following figure shows the controls and indicators on the storage array back panel and

drives.

Callout Indicator/LED: Color State Meaning

1 AC power fault indicator: amber ■ On – Indicates an AC power fault.

■ Off – Normal operation.

Overview of System Status Indicators and LEDs 11

Storage Array Back Panel Indicators

Callout Indicator/LED: Color State Meaning

2 Fan fail indicator: amber ■ On – The fan is faulty.

■ Off – Normal operation.

3 Power supply status indicator:

green

■ On – The power supply is operating normally.

■ Off – The power supply is unplugged or turned off.

4 DC power fail indicator: amber ■ On – The power supply is faulty.

■ Off – Normal operation.

5 Reserved This port is reserved for Oracle Service.

6 Network port (reserved) This port is reserved for Oracle Service.

7 Locate: white ■ Off – Normal operation.

■ Fast blink – This LED blinks to help locate the system. Operators

can turn this indicator on and off remotely using Oracle ILOM.

■ Pressing this button toggles the fast blink on or off.

8 Service Required: amber ■ Off – Normal operation.

■ Steady on – A fault is present in the storage array.

9 OK: green ■ On – The storage array is powered on and operating normally.

■ Off – The storage array is unplugged or turned off.

10 SAS I/O Module Ready-to-

Remove: blue

■ On – The I/O module can be safely removed during a hot-plug

operation.

■ Off – The I/O module has not been prepared for removal.

11 SAS I/O Module fault indicator:

amber

Service Required – Lights amber to indicate a fault with an I/O

module.

12 SAS I/O Module OK: green ■ On – The I/O module is powered on and operating normally.

■ Off – The I/O module is unplugged or turned off.

13 Host SAS port fault indicator:

amber

Service Required – Lights amber to indicate a fault with the port or

connection.

14 Host SAS port activity indicator:

green

Lights green to indicate host SAS link activity.

12 Oracle MiniCluster S7-2 Service Manual • March 2017

Preparing MiniCluster for Service

This chapter describes how to prepare MiniCluster for servicing.

■

“Detecting and Managing Faults” on page 13

■

“Preparing MiniCluster For Service” on page 14

■

“Component Service Categories” on page 14

Detecting and Managing Faults

Note - The links in the following list take you to instructions outside of the MiniCluster library

to the SPARC S7-2 documentation libraries. Use your browser's Back button to return to the

MiniCluster library.

■

“Checking for Faults” in SPARC S7-2 Server Service Manual

■

“Log In to Oracle ILOM (Service)” in SPARC S7-2 Server Service Manual

■

“Identify Faulted Components” in SPARC S7-2 Server Service Manual

■

“Performing Advanced Troubleshooting” in SPARC S7-2 Server Service Manual

■

“Check the Message Buffer” in SPARC S7-2 Server Service Manual

■

“View Log Files (Oracle Solaris)” in SPARC S7-2 Server Service Manual

■

“View Log Files (Oracle ILOM)” in SPARC S7-2 Server Service Manual

■

“POST Overview” in SPARC S7-2 Server Service Manual

■

“Configure POST” in SPARC S7-2 Server Service Manual

■

“Oracle ILOM Properties That Affect POST Behavior” in SPARC S7-2 Server Service

Manual

■

“Clear a Fault Manually” in SPARC S7-2 Server Service Manual

Preparing MiniCluster for Service 13

Preparing MiniCluster For Service

Most service procedures are performed on a single appliance component. Service procedures

that require a single compute node to be powered off can be performed without shutting down

the entire MiniCluster. Before powering off any component for service, refer to the Getting

Started Guide or Administration Guide for any special instructions or commands that must be

performed on the MiniCluster to prepare it for service.

Note - The links in the following list take you to instructions outside of the MiniCluster library

to the SPARC S7-2 documentation libraries. Use your browser's Back button to return to the

MiniCluster library.

■

“Safety Information” in SPARC S7-2 Server Service Manual

■

“Service Tools” in SPARC S7-2 Server Service Manual

■

“Find the Server Serial Number” in SPARC S7-2 Server Service Manual

■

“Locate the Server” in SPARC S7-2 Server Service Manual

■

“Prepare to Power Off the Server” in SPARC S7-2 Server Service Manual

■

“Power Off the Server” in SPARC S7-2 Server Service Manual

■

“Disconnect Cables From the Server” in SPARC S7-2 Server Service Manual

■

“Prevent ESD Damage” in SPARC S7-2 Server Service Manual

■

“Extend the Server to the Service Position” in SPARC S7-2 Server Service Manual

■

“Remove the Server From the Rack” in SPARC S7-2 Server Service Manual

■

“Open the Server Fan Door” in SPARC S7-2 Server Service Manual

■

“Remove the Top Cover” in SPARC S7-2 Server Service Manual

Component Service Categories

The server components and assemblies that can be replaced in the field fall into three

categories:

■

Hot-service, replaceable by customer

■

Cold-service, replaceable by customer

■

Cold-service, replaceable by authorized service personnel

Cold service procedures require that you shut the server down and unplug the power cables that

connect the power supplies to the power source.

14 Oracle MiniCluster S7-2 Service Manual • March 2017

Component Service Categories

Although hot service procedures can be performed while the server is running, you should

usually bring it to standby mode as the first step in the replacement procedure. See “Preparing

MiniCluster For Service” on page 14 for instructions.

This table identifies the components in each category.

Component Service

Category

Component Service Information

Hot-service, replaceable by

customer

Drives, compute node “Servicing Drives” in SPARC S7-2 Server Service Manual

Fan modules, compute node “Servicing Fan Modules” in SPARC S7-2 Server Service Manual

Power supplies, compute

node

“Servicing Power Supplies” in SPARC S7-2 Server Service Manual

HDD or SSD, storage array “Replace a Storage Array HDD or SSD (CRU) ” on page 18

Power supplies, storage

array

“Replace a Storage Array Power Supply (CRU)” on page 24

I/O module, storage array “Replace a Storage Array I/O Module (CRU)” on page 28

Cold-service, replaceable by

customer

DIMMs, compute node “Servicing DIMMs” in SPARC S7-2 Server Service Manual

Battery, compute node “Servicing the Battery” in SPARC S7-2 Server Service Manual

PCIe cards, compute node “Servicing PCIe Cards” in SPARC S7-2 Server Service Manual

Front indicator module,

compute node

“Servicing the Front Indicator Module” in SPARC S7-2 Server Service

Manual

eUSB drive, compute node “Servicing the eUSB Drive” in SPARC S7-2 Server Service Manual

Cold-service, replaceable by

authorized service personnel

Cables, compute node “Servicing Cables” in SPARC S7-2 Server Service Manual

Drive backplane, compute

node

“Servicing the Drive Backplane” in SPARC S7-2 Server Service Manual

Motherboard, compute node “Servicing the Motherboard” in SPARC S7-2 Server Service Manual

Preparing MiniCluster for Service 15

16 Oracle MiniCluster S7-2 Service Manual • March 2017

Servicing CRUs That Do Not Require System

Power Off

This chapter describes how to remove and replace the hot-swappable components in

MiniCluster. Hot-swappable means that these components can be replaced with the system

powered on.

Note - Hot-swappable components can also be replaced with the system powered off. If you

choose this method, first power off the system as described in “Preparing MiniCluster for

Service” on page 13.

The following topics are covered:

■

“Compute Node Hot-Swappable Components” on page 17

■

“Storage Array Hot-Swappable Components” on page 18

Compute Node Hot-Swappable Components

This section describes replacing hot-swappable components for the compute node.

Hot-swappable components are those that can be removed and installed while the system and

the compute nodes are running without requiring any administrative tasks. These are designated

as Customer Replaceable Units (CRUs).

Refer to the following table for hot-swap component instructions for your appliance.

Note - The links in the following table take you to instructions outside of the MiniCluster

library to the SPARC S7-2 documentation library. Use your browser's Back button to return to

the MiniCluster library.

■

“Servicing Drives” in SPARC S7-2 Server Service Manual

Servicing CRUs That Do Not Require System Power Off 17

Storage Array Hot-Swappable Components

■

“Servicing Fan Modules” in SPARC S7-2 Server Service Manual

■

“Servicing Power Supplies” in SPARC S7-2 Server Service Manual

Storage Array Hot-Swappable Components

This section describes replacing hot-swappable components for the storage array.

Hot-swappable components are those that can be removed and installed while the system and

the compute nodes are running without requiring any administrative tasks. These are designated

as Customer Replaceable Units (CRUs).

Caution - Data loss. Do not remove power from both power supplies of the storage array or

storage expansion shelf (if equipped) while the database is running. If you must power off the

storage array or expansion storage array, stop the database first.

Note - After a physical insertion or removal action of a storage array component (such as a disk

or SAS cable), you should wait before performing the next action to allow the system software

to fully process the event. This could take up to 3 minutes to complete.

Replacement Procedures

These storage array components can be replaced while the storage array is powered-on and

running:

■

“Replace a Storage Array HDD or SSD (CRU) ” on page 18

■

“Replace a Storage Array Power Supply (CRU)” on page 24

■

“Replace a Storage Array I/O Module (CRU)” on page 28

Replace a Storage Array HDD or SSD (CRU)

Use these procedures to replace a storage array HDD or SSD.

■

“Remove a Storage Array HDD or SSD (CRU)” on page 19

■

“Install a Storage Array HDD or SSD (CRU)” on page 22

18 Oracle MiniCluster S7-2 Service Manual • March 2017

Remove a Storage Array HDD or SSD (CRU)

Enter the appropriate commands through the CLI to prepare the drive for

removal from the storage array.

Use this procedure to logically remove a storage array drive from the system before you

physically remove the drive.

The length of time that it takes to complete this procedure before you can physically remove the

drive depends on the type of drive you are removing:

■

SSD – The detach operation completes quickly and the drive can be removed immediately.

■

HDD – The detach operation takes several minutes to complete. Do not remove the drive

before the detach operation competes.

Log into the mcmu CLI as a primary admin such as mcinstall.

% ssh mcinstall@minicluster_node_name_or_IPaddress

where minicluster_node_name_or_IPaddress is the name of the first node on MiniCluster,

or the IP address of the first node.

For example:

% ssh mcinstall@mc4-n1

When prompted, enter the password.

For more information about running mcmu CLI commands, refer to the Oracle MiniCluster

S7-2 Installation Guide or the Oracle MiniCluster S7-2 Administration Guide.

Identify the drive name.

You might be able to get the drive name from the error message or log file that led to the

plan to replace the drive.

You can use a command such as diskinfo. Make note of the long drive name (such as

c0t5000CCA23B0BF34Cd0) for use with this procedure. Also make note of the shorter name

(such as HDD8) for use with the followup task when you reattach the replaced drive.

Also note that the storage array drives are identified by a JBODARRAY string.

For example:

% diskinfo

D:devchassis-path c:occupant-compdev

---------------------------------- ---------------------

/dev/chassis/SYS/HDD0/disk c0t5000CCA02D1EE2A8d0

/dev/chassis/SYS/HDD1/disk c0t5000CCA02D1E7AACd0

Servicing CRUs That Do Not Require System Power Off 19

Remove a Storage Array HDD or SSD (CRU)

/dev/chassis/SYS/HDD2/disk c0t5000CCA02D1EDCECd0

/dev/chassis/SYS/HDD3/disk c0t5000CCA02D1ED360d0

/dev/chassis/SYS/HDD4/disk c0t5000CCA02D1EE6D8d0

/dev/chassis/SYS/HDD5/disk c0t5000CCA02D1EE6CCd0

/dev/chassis/SYS/HDD6 -

/dev/chassis/SYS/HDD7 -

/dev/chassis/SYS/MB/EUSB-DISK/disk c1t0d0

/dev/chassis/JBODARRAY1/HDD0/disk c0t5000CCA25497267Cd0

/dev/chassis/JBODARRAY1/HDD1/disk c0t5000CCA2549732B8d0

/dev/chassis/JBODARRAY1/HDD2/disk c0t5000CCA254974F28d0

/dev/chassis/JBODARRAY1/HDD3/disk c0t5000CCA254965A78d0

/dev/chassis/JBODARRAY1/HDD4/disk c0t5000CCA254978510d0

/dev/chassis/JBODARRAY1/HDD5/disk c0t5000CCA254964E3Cd0

/dev/chassis/JBODARRAY1/HDD6/disk c0t5000CCA0536CA5E4d0

/dev/chassis/JBODARRAY1/HDD7/disk c0t5000CCA0536CA7B0d0

/dev/chassis/JBODARRAY1/HDD8/disk c0t5000CCA23B0BF34Cd0

/dev/chassis/JBODARRAY1/HDD9/disk c0t5000CCA0536CB828d0

/dev/chassis/JBODARRAY1/HDD10/disk c0t5000CCA0536CB308d0

/dev/chassis/JBODARRAY1/HDD11/disk c0t5000CCA0536CAF2Cd0

/dev/chassis/JBODARRAY1/HDD12/disk c0t5000CCA0536CABE4d0

/dev/chassis/JBODARRAY1/HDD13/disk c0t5000CCA0536CB684d0

/dev/chassis/JBODARRAY1/HDD14/disk c0t5000CCA0536CA870d0

/dev/chassis/JBODARRAY1/HDD15/disk c0t5000CCA0536CAB88d0

/dev/chassis/JBODARRAY1/HDD16/disk c0t5000CCA0536CA754d0

/dev/chassis/JBODARRAY1/HDD17/disk c0t5000CCA0536CAD10d0

/dev/chassis/JBODARRAY1/HDD18/disk c0t5000CCA0536CAEF8d0

/dev/chassis/JBODARRAY1/HDD19/disk c0t5000CCA0536CA83Cd0

/dev/chassis/JBODARRAY1/HDD20/disk c0t5000CCA04EB272E8d0

/dev/chassis/JBODARRAY1/HDD21/disk c0t5000CCA04EB27234d0

/dev/chassis/JBODARRAY1/HDD22/disk c0t5000CCA04EB27428d0

/dev/chassis/JBODARRAY1/HDD23/disk c0t5000CCA04EB272A0d0

Use this syntax to detach the disk prior to removing the disk:

% mcmu diskutil -d diskname

where diskname is the disk identifier of the drive you plan to remove.

For example:

% mcmu diskutil -d c0t5000CCA23B0BF34Cd0

INFO:MCMU.controllers.common.pexpect_util:su to user oracle successfully.

[INFO ] logged into the zone f18-vm1-mc5qt-n1 as oracle

[INFO ] disk alias found to be RECO_0003

[INFO ] dropping disk c0t5000CCA23B0BF34Cd0s1

20 Oracle MiniCluster S7-2 Service Manual • March 2017

La page charge ...

Oracle MiniCluster S7-2 Manuel utilisateur

Marque: Oracle

Modèle: MiniCluster S7-2

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Oracle MiniCluster S7-2 User manual

Oracle MiniCluster S7-2 Manuel utilisateur

Oracle MiniCluster S7-2 Manuel utilisateur

dans d''autres langues

Documents connexes