Bosch SHX84AAF5N Guide d'installation

en Installation Instructions

fr Notice d’installation

es Instrucciones de instalación

Customer Service:

1-800-944-2904

These instuctions are intended

for use by qualified installers only

2

3

To avoid possible injury or property damage, OBSERVE ALL WARNINGS

AND CAUTIONS.

These instructions are intended for use by qualied installers only. The

dishwasher must be installed by a qualied service technician or installer.

• In addition to these instructions, the dishwasher shall be installed to

meet all electrical and plumbing codes and ordinances (both national

and local).

Read these installation instructions completely and follow them

carefully. They will save you time and eort and help to ensure safety and

optimum dishwasher performance.

IMPORTANT

• The dishwasher drain hose must be installed with a portion of it at least

33″ (84 cm) o the cabinet oor; otherwise the dishwasher may not

drain properly.

• This dishwasher is intended for indoor residential use only, and should

not be used in commercial food service establishments.

• This dishwasher is designed to be enclosed on the top and both sides

by cabinetry.

• NEW INSTALLATION - If the dishwasher is a new installation, ensure

all connections are properly made before the dishwasher is moved into

place.

• REPLACEMENT - If the dishwasher is replacing another dishwasher,

check the existing dishwasher connections for compatibility with the

new dishwasher, and replace parts as necessary.

• This appliance has been found to be in compliance with CAN/CSA-C22.2

No. 167/UL 749. It is the responsibility of the owner and the installer

to determine if additional requirements and standards apply in specic

installations.

• Not for outdoor use.

Important Safety Instructions:

Please READ and SAVE this information

4

Avoiding General Hazards

Do not use the dishwasher until it is completely installed. When opening

the door on an uninstalled dishwasher, carefully open the door while

supporting the rear of the unit. Failure to follow this warning can cause the

dishwasher to tip over and result in serious injury.

Before installing the “L”-shaped supplied countertop mounting brackets

(select models), decide which method will be used to secure the dish-

washer into its opening. Once these mounting brackets are installed on

the dishwasher, removing them is dicult and will damage the mounting

brackets and the dishwasher.

In some conditions, hydrogen gas can form in a hot water system that

has not been used for weeks. Hydrogen gas is explosive. Before lling a

dishwasher from a system that has been o for weeks, run the water from

a nearby faucet in a well ventilated area until there is no sound or evidence

of gas.

Temperatures required for soldering and sweating will damage the

dishwasher’s base and water inlet valve. If plumbing lines are to be

soldered or sweated, keep the heat source at least 6 inches (152.4 mm)

away from the dishwasher’s base and water inlet valve.

Removing any cover or pulling the dishwasher from the cabinet can

expose hot water connections, electrical power and sharp edges or points.

Handle with care.

Avoiding Electrical Shock/Fire Hazards

Do not allow the electrical and water supply lines to touch.

Do not work on an energized circuit. Doing so could result in serious

injury or death. Only qualied electricians should perform electrical work.

Do not attempt any work on the dishwasher electric supply circuit until

you are certain the circuit is de-energized.

Make sure electrical work is properly installed. There should be no loose

electrical connections. Ensure all electrical connections are properly

made.

WARNING

5

The customer has the responsibility of ensuring that the dishwasher

electrical installation is in compliance with all national and local electrical

codes and ordinances. The dishwasher is designed for an electrical supply

of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly

grounded electrical circuit with a fuse or breaker rated for 15 amps.

Electrical supply conductors shall be a minimum #14 AWG copper only

wire rated at 75°C (167°F) or higher.

This appliance must be connected to a grounded metal, permanent wiring

system, or an equipment-grounding conductor must be run with the circuit

conductors and connected to the equipment-grounding terminal or lead on

the appliance. Do not use extension cords.

Avoiding Plumbing/Scalding Hazards

Do not perform any work on a charged hot water line. Serious injury could

result. Only a qualied plumber should perform plumbing work. Do not

attempt any work on the dishwasher hot water supply plumbing until you

are certain the hot water supply is shut o.

Do not over tighten the 90° elbow. Doing so may damage the water inlet

valve and cause a water leak.

Check local plumbing codes for approved plumbing procedures and ac-

cessories. All plumbing should be done in accordance with national and

local codes.

These instructions depict an installation method for stainless steel braided

hose or PEX hot water supply lines. If using copper tubing or other material

for water supply, defer to a licensed plumber for proper installation.

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation, thoroughly inspect

the dishwasher for possible freight or cosmetic damage. Report any

damage immediately. Cosmetic defects must be reported within 30 days

of installation.

NOTE: Do not discard any bags or items that come with the original package

until after the entire installation has been completed.

6

Elbow connection with 3/4” female hose threads on one end and fits

your water supply line (copper tubing, compression fitting, or braided

hose) on the other.

Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground,

insulated copper conductors rated 75° C or higher.

Only needed if house electrical line is not adequate.

Hot Water Supply Line - Minimum 3/8″ O.D. copper tubing or metal

braided dishwasher supply line.

Only needed if house water supply line is not sucient.

Shut-o valve and fittings appropriate for hot water supply line

(copper tubing/compression fitting, or braided hose).

UL listed conduit connector or strain relief is required if you attach the

field wiring directly to the terminal block.

Tools and Materials Needed



Wire Cutter

Needle Nose Pliers

Pliers

Wire Stripper

ø1/16 in

(2 mm)

Adjustable Wrench

Tape Measure

Drill

Hole Saw

Flat Screwdriver

Level

Phillips Screwdriver

7

Materials supplied (All Models)

Screw Clamp (for drain hose)

X 5

Mounting Brackets

Mounting Bracket Screws Ø 4x13 mm

D

E

F

B

A

C

G

H

Clamp (for drain hose)

Screws

Terminal block cover screw

Metal toe panel screws

Drain hose

X 2

Metal Toe Panel (used with F)

I

8

Materials Supplied

(Model Dependent; for fully integrated dishwashers only)

Installation Guide for Fully Integrated Door Panel

9

IMPORTANT!

Before you begin, you must read the safety instructions.

PRE-INSTALL CHECKLIST

� Unpack unit. Retain packing material until successful installation is

complete.

� Remove all packing material from inside the dishwasher.

� Inspect parts to ensure you have all the necessary materials.

� Flush household hot water supply for at least two minutes.

� Measure the enclosure area.

� Is the opening at least 34" (863.6 mm) high and 24" (609.6 mm) wide?

� Is the opening near enough to the sink for the water line and drain

hoses to access plumbing?

� Will the unit be installed close enough to the sink so that drain hose

length does not exceed 92" (2336.8 mm) and so that a portion of the

drain hose is raised at least 33" (840 mm) above the oor?

� Do the openings for electric cable, water line, and drain hose routing

through cabinet t within the shaded area in Figure 1?

� Are the openings sanded smooth if wood or covered by a protective

gasket if metal?

� Is your water heater set at 120°F (49°C) and does water pressure

measure 15-145 psi (1-10 bar)?

� If installing in a corner, will the dishwasher door clear cabinet

hardware?

� Determine mounting method based on dishwasher model and

countertop type (see Figures 19-22).

� Only use included hardware for install. If replacing dishwasher,

dispose of old hose and other equipment properly.

10

24" (600 mm) with side

strips removed.

Minimum hole size for drain

hose is 1 1/2" (38.1 mm).

Minimum hole size if drain

hose and inlet hose are

through same hole is 2"

(50.8 mm).

Remove the toe panel (Part I) from the front of the unit and retain for

attachment to the front at a later time. Loosen the leg levelers slightly.

Remove junction box cover and retain for later use (2). Discard the small

piece of protective styrofoam.

4

" (102 mm)

2" (51 mm)

24 - 24

1

/

4

" (610-616 mm)*

90°

24" (610 mm)

33

7

/

8

" (86 cm) min

1

2

I

2

11

Attach 90° elbow joint to dishwasher

oriented as shown. Do not over-

tighten.

Attach hot water line to 90° elbow

and route underneath machine

toward hot water connection. Ensure

the hose does not contact any

moving parts beneath the unit.

Turn power o at fuse box. Extend

cable approximately 21" (533.4 mm)

from the opening’s left side. Extend

the cable 30" (762 mm) from the

back wall.

3

4

21"

(533.4 mm)

30"

(762 mm)

5

12

Strip outer casing of

electrical wire to expose

3" (76.2 mm) of the inner

wires. Then strip 1/2" (12.7

mm) casing from each

individual wire.*

* If the dishwasher will be

plugged into an electric

receptacle, contact

customer service

(1-800-735-4328) to order

approved power cord

accessory kit (SKU #

SGZPC001UC).

Flip unit back upright,

ensuring waterline is not

pinched.

Remove strain relief plate. Do not

discard! This will be reinstalled

later.

1/2"

(13mm)

3"

(76mm)

6

8

Do Not Over-tighten or

Remove Terminal Screws

7

Dishwasher Electrical Rating

VoltsHertz AmperesWatts

12060121,450 (max)

13

Orient the drain hose toward

direction of sink.

IMPORTANT: Route hose toward

sink PRIOR TO connection. Do

not turn after attachment. Attach

drain hose elbow (Part G) to back

of unit using pliers to install the

spring clamp (Part B).

B

G

B

G

9

Pre-level unit before

positioning under counter

by turning feet clockwise

to raise or counter-

clockwise to lower.

Maximum height the unit

can be raised with feet

fully extended is 34.5"

(876.3 mm). Position

unit under counter to

verify that it is level. If

adjustment is needed,

remove unit from under

counter and adjust as

necessary. Once the

unit is at a satisfactory

height, insert leg leveler

locking screw (Part D)

in back foot. Step 18 will

complete the leveling

process.

D

10

14

IMPORTANT: Do not allow leg

levelers to scratch or mark oor.

Place hands where pictured to

push into place. As you slide

the unit in, guide the water line

and drain hose toward the sink,

and electric line beneath the

unit toward the junction box at

the front right side. Ensure that

the excess drain hose is pushed

through to the cabinet housing

the sink. Units are typically

positioned so that the door is

ush with cabinet door and

drawer fronts. For optimal noise

reduction, ensure side strips are

in contact with cabinet.

Attach the strain relief (not

included) to the strain relief plate.

The two screws on the back

of the strain relief should be

positioned as shown to prevent

interferences during assembly.

Tighten the strain relief lock nut

to prevent the strain relief from

turning.

Pass wires through strain relief

and plate. Tighten clamp around

wires, oriented as shown.

Bending the electrical cable as

shown will ease installation of the

strain relief plate.

11

12

13

15

Place the assembled strain relief

plate back into the junction box and

re-attach the screw. Make sure the

tab on the right side of the strain

relief plate is outside the junction

box as you slide it into place.

Do Not Over-tighten or

Remove Terminal Screws

14

Note: Do not loosen or remove

terminal screws! Damage may

occur. Bend the wires so the

exposed leads can reach the

appropriate contacts. Insert the

black (hot) wire into the left opening

on the terminal strip marked “L”, the

white (neutral) wire in the middle

opening of the terminal strip marked

“N”, and the bare copper or green

(ground) wire into the right opening

of the terminal strip marked “G”.

Do Not Over-tighten or

Remove Terminal Screws

15

Make sure that the exposed

(non-insulated) portion of each

stripped wire shows above

and below the terminal screw.

Securely tighten the terminal

screws, but do not over-tighten

or damage may occur.

Hand tighten only. Do not use

power tools.

16

Replace junction box cover.

Make sure the cover is seated

behind the front lip of the strain

relief plate. Attach the cover

with the screw (Part E) from the

installation kit.

Warning

............................

..........................................

E

17

Level the dishwasher horizontally by turning feet (1) clockwise to

raise or counter-clockwise to lower front of unit. Once level, (2)

insert leg leveler locking screws (Part D) and tighten.

(1)

(2)

D

18

17

Grasp mounting bracket (H) with pliers and fold bracket at the perforation over

onto itself as shown in 19a.

• Mount brackets on the top if your countertop is wood or other

material that can easily be drilled into. (see gure 19b)

• Mount brackets on the sides if your countertop is stone or any very

hard material that cannot be easily drilled into. (see gure 19b)

19

Attach mounting brackets to the frame with included screws (D).

20

a

Wood Countertop/

Top Mount

Stone Countertop/

Side Mount

18

Drive the mounting screws (A) through the holes in the mounting brackets

as shown for Top ( gure 21) or Side Mount (gure 22). Remove upper rack

before inserting screws on the sides.

21













22

A

19

The dishwasher drain hose may be connected to the drain plumbing using

an air gap in one of two ways:

- Connect to the under sink dishwasher drain connection (25a).

- Connect to a disposer dishwasher drain connection (25b).

NOTE: Place hose clamp (C) around end of drain hose BEFORE connecting

to the plumbing.







23

a b

C

IMPORTANT NOTES about your drain connection:

• If local ordinance require an air gap, install it according to the manufac-

turer’s instructions.

• If the dishwasher drain hose is to be connected to a disposer dishwasher

drain connection, remove the plug from the disposer’s dishwasher drain

connection.

• The dishwasher drain hose must have one place along its length that is securely

attached 33″ (84 cm) above the cabinet oor.

• The drain hose length can be extended if necessary. The maximum length

of the drain hose, including the hose leading to the air gap, is 150″ (380 cm).

Drain Connection

20

min 33” (84 cm)

max 43” (110 cm)

min 33” (84 cm)

max 43” (110 cm)

The dishwasher drain hose may be connected to the drain plumbing using a

high loop in one of two ways:

- Connect to the under sink dishwasher drain connection (25c).

- Connect to a disposer dishwasher drain connection (25d).

c

d

C

Use the clamp provided (C) to attach

the drain hose to the house plumbing as

shown.















24

C

La page charge ...

Bosch SHX84AAF5N Guide d'installation

Ce manuel convient également à

Bosch SHX84AAF5N Guide d'installation

dans d''autres langues

Documents connexes

Autres documents