Yamaha CHH920 Le manuel du propriétaire

Yamaha
Marque
Yamaha
Modèle
CHH920
Catégorie
Détenteurs
Taper
Le manuel du propriétaire
CLOSED HI-HAT HOLDER
CHH-920
OWNER’S MANUAL
Thank you for purchasing the Yamaha CHH-920 Closed Hi-Hat Holder. For a full understanding of
its functions and to obtain maximum use and long life from the product, please read this Owner’s
Manual thoroughly before use.
q
Cymbal Support Plate
To attach the bottom hi-hat cymbal, first remove the hi-hat clutch, wing
nut and felt. Next, confirm that the metal plate and rubber washer are
on the cymbal support plate and set the bottom hi-hat cymbal, felt
(small) and wing nut on the holder in that order. Finally, tighten the
wing nut to secure the cymbal in place.
The angle of the cymbal can be adjusted by rotating the knurled-head
bolt, located under the support plate, then securing the bolt in place
with the fixing nut.
w
Hi-Hat Clutch
To attach the top hi-hat cymbal, remove the clutch nut and place the
top cymbal between the felts. Screw the clutch nut back onto the clutch
bolt and tighten firmly.
The lock nuts above the felt can be used to adjust the overall feel and
sound of the hi-hat cymbals. For a loose sound, loosen the nuts off
from the felt; for a tight sound, tighten the nuts onto the felt. Once the
desired sound has been obtained, firmly tighten the lock nuts onto
each other.
e
Cymbal Position
The large spring tension dial is used to adjust the span between the
cymbals.
Rotate the dial to the right to close, or to the left to open the span
between the cymbals.
The system is equipped with an indicator for easy reference and set-
ting.
r
Open Clamp
To adjust the angle of the entire closed hi-hat holder, loosen the wing
nut (A) on the tilter. Once the unit is set to the desired angle, firmly
tighten the wing nut.
Also, the CHH-920 is held in place with an Open Clamp. Make sure
that the clamp’s sections are parallel then tighten both nuts firmly.
t
Mounting Pipe
The 22.2 mm diameter mounting pipe for the hi-hat holder makes pos-
sible a wide variety of set-ups. It can be mounted to YAMAHA tom
holders and the bass side of double tom stands. The hi-hat holder can
also be mounted with YAMAHA pipe clamps and clamp accessories
such as Open Clamps (OC-910U and OC-920R), Arm Clamps (AC-
910), and Cymbal Stand Attachments (CSAT-924).
y
Position Clamp
Once the closed hi-hat holder set-up has been decided, the position
clamp on the mounting pipe can be used to mark the settings for fu-
ture set ups and to prevent unintentional changes during musical per-
formances. Use a drum key to firmly tighten the position clamp into
place.
Note:
To maintain smooth action, occasionally apply some grease-grade
oil to all of the moving parts.
CHH-920 Closed Hi-Hat Holder
* Specification and design are subject to change without notice.
●
Hi-Hat Clutch
Clutch Bolt
Wing Bolt
Spring Tension Dial
Hi-Hat Clutch
Indicator
Position Clamp
Wing Nut (A)
Open Clamp
Felt
Clutch Nut
Lock Nut
●
Cymbal Support Plate
Cymbal Support Plate
Knurled-Head Bolt
Rubber Washer
Cymbal Support Plate
Wing Nut
Felt
Metal Plate
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Yamaha CHH920 Le manuel du propriétaire

Yamaha
Marque
Yamaha
Modèle
CHH920
Catégorie
Détenteurs
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes