Whirlpool WRT541SZDB Mode d'emploi

Marque: Whirlpool

Modèle: WRT541SZDB

Catégorie: Frigos

Taper: Mode d'emploi

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.whirlpool.com. In Canada, register your

refrigerator at www.whirlpool.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall of the

refrigerator compartment.

Model Number ___________________________________________ Serial Number____________________________________________

REFRIGERATOR

USER INSTRUCTIONS

Table of Contents / Índice / Table des matières

REFRIGERATOR SAFETY............................... 2

INSTALLATION INSTRUCTIONS ................... 3

Unpack the Refrigerator................................ 3

Proper Disposal of Your Old Refrigerator..... 3

Location Requirements................................. 4

Electrical Requirements ................................ 4

Water Supply Requirements......................... 4

Connect the Water Supply............................ 5

Refrigerator Doors......................................... 6

Reversibility Kit Instructions........................ 11

Adjust the Doors ......................................... 11

REFRIGERATOR USE ................................... 12

Using the Controls ...................................... 12

Ice Maker..................................................... 12

REFRIGERATOR FEATURES ....................... 13

Refrigerator Shelves.................................... 13

Deli Drawer.................................................. 13

Crisper......................................................... 13

FREEZER FEATURES ................................... 14

Wire Freezer Shelf....................................... 14

Glass Freezer Shelf ..................................... 14

DOOR FEATURES ......................................... 15

Door Rails.................................................... 15

Door Bins..................................................... 15

Utility Compartment.................................... 15

REFRIGERATOR CARE................................. 15

Cleaning ...................................................... 15

Changing the Light Bulbs ........................... 16

Vacation and Moving Care ......................... 16

PROBLEM SOLVER....................................... 17

ACCESSORIES .............................................. 19

WARRANTY.................................................... 20

BRAND BADGE

PLACEMENT TEMPLATE .........BACK COVER

SEGURIDAD DEL REFRIGERADOR ............ 21

Cómo deshacerse adecuadamente

de su refrigerador viejo ............................... 22

INSTRUCCIONES DE INSTALACIÓN .......... 22

Desempaque el refrigerador ....................... 22

Requisitos de ubicación.............................. 23

Requisitos eléctricos................................... 23

Requisitos del suministro de agua.............. 24

Conexión del suministro de agua............... 24

Puertas del refrigerador .............................. 25

Instrucciones del juego para

invertir el cierre de la puerta........................ 30

Ajuste las puertas........................................ 30

USO DE SU REFRIGERADOR ...................... 31

Uso de los controles ................................... 31

Fábrica de hielo........................................... 32

CARACTERÍSTICAS

DEL REFRIGERADOR................................... 32

Estantes del refrigerador............................. 32

Cajón para carnes frías............................... 32

Cajón para verduras.................................... 33

CARACTERÍSTICAS DEL CONGELADOR .. 33

Estante de alambre del congelador............ 33

Estante de vidrio del congelador................ 34

CARACTERÍSTICAS DE LA PUERTA .......... 34

Rieles de la puerta ...................................... 34

Recipientes de la puerta ............................. 34

Compartimiento de uso general ................. 35

CUIDADO DE SU REFRIGERADOR............. 35

Limpieza ...................................................... 35

Cómo cambiar los focos............................. 35

Cuidado durante las

vacaciones y mudanzas.............................. 36

SOLUCIÓN DE PROBLEMAS....................... 37

ACCESORIOS ................................................ 39

GARANTÍA...................................................... 40

PLANTILLA DE COLOCACIÓN

DE LA PLACA....................CONTRAPORTADA

SÉCURITÉ DU RÉFRIGÉRATEUR................ 41

Mise au rebut appropriée

de votre vieux réfrigérateur......................... 42

INSTRUCTIONS D’INSTALLATION.............. 42

Déballage du réfrigérateur .......................... 42

Exigences d'emplacement ......................... 43

Spécifications électriques........................... 43

Spécifications de l’alimentation en eau...... 44

Raccordement de la canalisation d'eau ..... 44

Portes du réfrigérateur................................ 45

Instructions pour l'ensemble

d’inversion du sens d’ouverture ................. 50

Ajustement des portes................................ 50

UTILISATION DU RÉFRIGÉRATEUR ........... 51

Utilisation des commandes ........................ 51

Machine à glaçons...................................... 52

CARACTÉRISTIQUES

DU RÉFRIGÉRATEUR ................................... 52

Tablettes du réfrigérateur............................ 52

Tiroir pour spécialités alimentaires ............. 52

Bac à légumes ............................................ 53

CARACTÉRISTIQUES

DU CONGÉLATEUR ...................................... 53

Tablette métallique du congélateur ............ 53

Tablette en verre du congélateur................ 53

CARACTÉRISTIQUES DE LA PORTE.......... 54

Tringles de porte ......................................... 54

Balconnets de porte.................................... 54

Compartiment utilitaire................................ 54

ENTRETIEN DU RÉFRIGÉRATEUR ............. 55

Nettoyage.................................................... 55

Remplacement des

ampoules d’éclairage.................................. 55

Entretien avant les vacances ou

lors d’un déménagement............................ 56

RÉSOLUTION DE PROBLÈMES................... 57

ACCESSOIRES .............................................. 59

GARANTIE...................................................... 60

Brand Badge Placement Template /

Gabarit de positionnement de

l'insigne de la marque................................. 62

GABARIT DE POSITIONNEMENT

DE L’INSIGNE

DE LA MARQUE.......COUVERTURE ARRIÈRE

W10726057A

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

WARNING:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

NOTE: Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove tape or glue.

These products can damage the surface of your refrigerator.

For more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

IMPORTANT: Do not remove the white foam air return insert that

is located behind the control panel on the ceiling of the refrigerator

(on some models). The insert is part of the refrigerator and not

part of the packing material. If the insert is removed, ice may

migrate down from the freezer and cause icicles to form.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Location Requirements

IMPORTANT: This refrigerator is designed for indoor household

use only.

To ensure proper ventilation for your refrigerator, allow for ½"

(1.25 cm) of space on each side and at the top. Allow for 1"

(2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on the hinge side (some

models require more) to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for

optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the

electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset the

control (Thermostat, Refrigerator or Freezer Control depending on

the model) to the desired setting. See “Using the Controls” in the

User Instructions, User Guide, or Use & Care Guide.

Water Supply Requirements

Read all directions before you begin.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED: Flat-blade screwdriver, ⁷⁄₁₆" and ¹⁄₂" open-end

wrenches or 2 adjustable wrenches, ¹⁄₄" nut driver and drill bit,

cordless drill.

IMPORTANT:

■ If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

■ All installations must meet local plumbing code requirements.

■ Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2" (1.25 cm)

2" (5.08 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Water Pressure

IMPORTANT: A cold water supply with water pressure between

30 and 120 psi (207 and 827 kPa) is required to operate the ice

maker.

NOTE: If the water pressure is less than what is required, ice

cubes could be hollow or irregular shaped.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the ice maker is still not operating properly:

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn ON the refrigerator before the water line

is connected, turn OFF the ice maker.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you

have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

1. Unplug refrigerator or disconnect power.

2. Attach the copper tubing to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

6. The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in

the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill ice container.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

DEF

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Refrigerator Doors

Tools Needed:

IMPORTANT:

■ Before you begin, turn the refrigerator control OFF. Unplug

refrigerator or disconnect power.

■ Remove food and adjustable door or utility bins from doors.

■ If you are only removing and replacing the doors, see the

“Remove Doors and Hinges” and “Replace Doors and

Hinges” sections.

■ Depending on your model, you may have standard (Style 1) or

contoured (Style 2) doors. If you are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

NOTE: A Reversibility Kit, which includes a new Brand Badge

and hole covers, is available.

■ All graphics referenced in the following instructions are

included later in this section after “Final Steps.”

Remove Doors and Hinges

⁵⁄₁₆" Hex-head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

4. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

5. Remove base grille from the bottom front of the refrigerator.

6. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open

in the opposite direction, follow these steps. If you are not

reversing the doors, see “Replace Doors and Hinges.”

Style 1 - Standard Door Models

Graphics follow these instructions.

Cabinet

1. Remove the three dome caps and the screws from handle

side and move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

Freezer Door

1. Remove the screw cover. See Graphic 2.

2. Remove the freezer handle assembly as shown. Keep all parts

together. See Graphic 2.

3. Remove door hinge hole plug from freezer door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove the brand badge using the plastic tool (provided).

Replace it with the badge provided in the Reversibility Kit

located inside the crisper drawer. For proper placement, see

the Brand Badge Placement template (the last page of this

manual).

NOTES:

■ To avoid scratching the finish, do not use a sharp or

metallic object to pry the brand badge from the door.

■ Rub a small amount of liquid dish soap over any adhesive

residue with your fingers. Rinse the door with warm water

and dry with a soft cloth.

5. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 5.

6. Position freezer handle on opposite side of the freezer door as

shown. See Graphic 2. First, drive the bottom two screws into

handle. Align upper portion of handle and drive top screw into

handle.

7. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

8. Replace screw cover. See Graphic 2.

■ ⁵⁄₁₆" Hex-head socket

wrench

■ ⁵⁄₁₆" Open-end wrench

■ #2 Phillips screwdriver ■ Flat 2" putty knife

■ Flat-blade screwdriver

Door Stop Screw

Door Handle Sealing Screw

Flat-Head Handle Screw

Door Handle Hole Plug

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Dome Cap

Dome Cap Washer

Refrigerator Door

1. Remove the screw cover. See Graphic 6.

2. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 6.

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove door handle sealing screws. Move to opposite side of

refrigerator door as shown. See Graphic 4.

5. Remove door handle hole plug and discard. See Graphic 7.

Replace on opposite side with the door handle hole plug

provided in the Reversibility Kit located in the crisper.

6. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 5.

7. Position refrigerator handle on opposite side of the refrigerator

door as shown. See Graphic 6. First, drive top two screws in

handle first. Align lower portion of handle and drive bottom

screw into handle.

8. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

9. Replace screw cover. See Graphic 6.

Style 2 - Contour Door Models

Graphics follow these instructions.

Cabinet

1. Remove the three dome caps and screws from handle side

and move them to opposite side. See Graphic 1-1.

2. Using the three

⁵⁄₁₆" hex-head hinge screws, insert two screws

halfway into the holes, leaving space to insert the center

hinge.

3. Slide the center hinge, from the right, onto the screws, insert

the third screw, and tighten all screws completely.

NOTE: Make sure the washers are in place on both the top

and bottom pins of the center hinge.

4. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown. See

Graphic 1-2.

Freezer Door

1. Remove the freezer door handle. Using a ¹⁄₈" hex key, loosen

the setscrew located on the side of the handle. Pull the handle

straight out from the door. Keep all parts together. See

Graphic 2.

2. Remove the brand badge using the plastic tool (provided).

Replace it with the badge provided in the Reversibility Kit

located inside the crisper. For proper placement, see the

Brand Badge Placement template (the last page of this

manual).

NOTES:

■ To avoid scratching the finish, do not use a sharp or

metallic object to pry the brand badge from the door.

■ Rub a small amount of liquid dish soap over any adhesive

residue with your fingers. Rinse the door with warm water

and dry with a soft cloth.

3. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 4.

4. Reinstall freezer handle on opposite side of the freezer door as

shown. See Graphic 2.

5. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

Refrigerator Door

1. Remove the refrigerator door handle. Using a ¹⁄₈" hex key,

loosen the setscrew located on the side of the handle. Pull the

handle straight out from the door. Keep all parts together. See

Graphic 6.

2. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

3. Remove door handle hole plug and discard. See Graphic 7.

Replace on opposite side with the door handle hole plug

provided in the Reversibility Kit located in the crisper.

4. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 4.

5. Reinstall refrigerator handle on opposite side of the

refrigerator door as shown. See Graphic 6.

6. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Measure the distance from the bottom of the refrigerator door

to the floor. The distance should be approximately 3¹⁄₂"

(88 mm).

NOTE: If necessary, loosen the bottom hinge, without

removing the screws, adjust the door to the correct height and

fully tighten the screws.

3. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic. Replace the freezer

door.

⁵⁄₁₆

" Hex-head hinge screws

B. Washers

Door Hinge

Hole Plug

Cabinet Hinge

Hole Plug

Dome Cap

Washer

Setscrew

Shoulder

Screw

Shoulder

Screw Washer

Door Stop

Screw

Flat-Head

Handle

Screw

Door Handle

Hole Cap

4. Assemble the parts for the top hinge as shown. See Top Hinge

graphic. Do not tighten screws completely.

Contour Door Models Only:

■ Remove the screw attaching the hinge pin to the hinge.

Turn the hinge over so that it is pointing in the opposite

direction.

■ Place the plastic spacer beneath the hinge so that it will

be between the hinge and the cabinet, making sure the

holes are aligned.

■ Fasten the top hinge to the opposite side of the cabinet,

inserting the screws only halfway, so you will be able to

replace and align the freezer door later.

5. Line up the doors so that the bottom of the freezer door aligns

evenly with the top of the refrigerator door. Tighten all screws.

NOTE: The distance between the doors should be

approximately ⁵⁄₈" (16 mm).

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover. See Top Hinge graphic.

2. Remove the cover from the base grille. Move the cover to the

opposite side.

3. Align the clips on the base grille with the screws on the

bottom of the cabinet. Push the base grille toward the cabinet

until it is flush.

4. Plug into a grounded 3 prong outlet.

5. Reset the controls. See “Using the Control(s).”

6. Return all removable door parts to doors and food to

refrigerator.

A. Plastic spacer

B. Hinge pin screw

C. Hinge pin

ACC

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Style 1 - Standard

Door Removal &

Replacement

Top Hinge

Door Swing Reversal (optional)

A. Door Hinge Hole Plug

A. Cabinet Hinge Hole Plugs

A. Door Handle Sealing Screws

A. Door Stop Screw

B. Door Stop

1-2

A. Flat-Head Handle Screw

B. Refrigerator Handle

C. Handle Screw

" Hex-Head Hinge Screws

C. Top Hinge

D. Screw Cover

Side View

Front View

Handle Screw

C. Freezer Handle

Screw Cover

Flat-Head Handle Screw

Base Grille

A. Door Handle

Hole Plug

A. Top Hinge Cover

Center Hinge

" Hex-Head Hinge Screws

A. Center Hinge

A. Bottom Hinge

Bottom Hinge

1-1

" Hex-Head Hinge

Screws,

Dome Caps and Dome Cap Washers

A. Cover

" Hex-Head Hinge Screws

Style 2 - Contour

Door Swing Reversal (optional)

1-2

A. Door Hinge Hole Plug

Removal of Door Stops

A. Cabinet Hinge Hole Plugs

Door Removal &

Replacement

A. Door Stop

B. Door Stop Screw

Reinstallation of Door Stops

A. Door Stop

B. Door Stop Screw

A. Shoulder Screw

B. Setscrew

C. Flat-Head Handle Screw

Base Grille

Center Hinge

Top Hinge

1-1

/16" Hex-Head Hinge

Screws,

Dome Caps and Dome Cap Washers

" Hex-Head Hinge Screws

A. Center Hinge

A. Flat-Head Handle Screw

B. Top Hinge

C. Hinge Pin

A. Bottom Hinge

Bottom Hinge

A. Cover

A. Door Handle

Hole Plug

" Hex-Head Hinge Screws

Reversibility Kit Instructions

If your model came with a Reversibility kit, please use the Brand

Badge Placement template and the following instructions to install

the Brand Badge on the opposite side of the freezer door.

Parts Included:

Brand badge removal tool

Brand badge template (on last page of User Instructions)

Door handle hole plug

Tools Needed:

Scissors

Masking tape

Freezer Door

1. Using the removal tool (provided), remove the brand badge

from the freezer door by lifting up the right-hand side and

peeling the badge away from the door from right to left.

NOTE: To avoid scratching the door, do not use a sharp or

metallic object to pry the brand badge from the door.

2. Rub a small amount of liquid dish soap over any adhesive

residue with your fingers. Rinse the door with warm water and

dry with a soft cloth.

3. Cut the template along the dotted lines that match the shape

of the brand badge.

4. Align the edges of the template with the side and top of the

freezer door and tape the template to the door.

NOTE: When the template is correctly aligned, the hole in the

door, where the handle was, will be within the cutout of the

template, as shown.

5. Using the cutout as a guide, press the brand badge onto the

freezer door making sure that the hole is completely covered.

6. Slowly remove the template.

Adjust the Doors

IMPORTANT: To comply with American Disabilities Act (ADA)

guidelines, fully retract the rollers into the cabinet to lower the

refrigerator.

Door Closing

Your refrigerator has two front adjustable rollers – one on the right

and one on the left. If your refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the following instructions:

1. Remove the base grille. See the Base Grille graphic in

“Refrigerator Doors.” The two leveling screws are part of the

front roller assemblies, which are at the base of the refrigerator

on either side.

2. Use a socket driver to adjust the leveling screws. Turn the

leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may

take several turns of the leveling screws to adjust the tilt of the

refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers which makes it easier to adjust.

3. Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to the

right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn both

leveling screws the same amount.

4. Replace the base grille.

Door Aligning

If the space between your doors looks uneven, you can adjust it

using the following instructions:

1. Depending on your model, remove the top hinge cover.

Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.

2. Have someone hold the door in place or put a spacer between

the doors while you tighten the top hinge screws.

3. Replace the top hinge cover, if removed in Step 1.

REFRIGERATOR USE

Using the Controls

Your refrigerator has two controls that affect the temperature. The

Temperature control is located at the top front of the refrigerator

compartment and the Airflow control is located on the back wall

of the freezer compartment.

IMPORTANT:

■ The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

■ Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Temperature Control

For your convenience, the Temperature control is preset at the

factory. When you first install your refrigerator, make sure the

control is still preset as shown.

Recommended Setting “3 Snowflakes”

Cooling Off/On

■ Move the dial control to the word OFF. To turn cooling back

on, move the dial control to the desired temperature setting.

NOTE: Neither compartment will cool when the control is set to

OFF.

Adjusting the Temperature Control

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart below as

a guide.

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

■ Move the dial to the desired number of snowflakes from

(1 least cold to 5 coldest).

Airflow Control

The Airflow control regulates the amount of air flowing between

the freezer and the refrigerator compartments.

When you plug in the refrigerator for the first time, turn the Airflow

control to the Recommended setting.

Adjusting the Airflow Control

If you want to temporarily increase the cold airflow to a specific

compartment, adjust the control.

■ Max - Increase airflow to the freezer

■ Min - Increase airflow to the refrigerator

IMPORTANT: Once the performance is achieved, return the

Airflow control to the Recommended setting to keep the

refrigerator operating at optimum efficiency.

Ice Maker

(on some models - Accessory)

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

■ To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

■ To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

NOTE: Turn the ice maker off before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from

dropping out of the ice maker and into the freezer compartment.

After replacing the ice storage bin, turn on the ice maker.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm TEMPERATURE Control one

setting higher

FREEZER too warm/too little

ice

AIRFLOW or TEMPERATURE

Control one setting higher

REFRIGERATOR too cold TEMPERATURE Control one

setting lower

FREEZER too cold AIRFLOW or TEMPERATURE

Control one setting lower

CONDITION/REASON: ADJUSTMENT:

Heavy ice use Max

Hot room temperature Max - To maintain ice making

production rate

Large quantity of groceries Min - To quickly chill food and

beverages

Ice Production Rate

■ NORMAL Ice Production: The ice maker should produce

approximately 8 to 12 batches of ice in a 24-hour period. If ice

is not being made fast enough, turn the Freezer Control

toward a higher (colder) number in half number steps. (For

example, if the control is at 3, move it to between 3 and 4.)

Wait 24 hours and, if necessary, gradually turn the Freezer

Control to the highest setting, waiting 24 hours between each

increase.

■ MAXIMUM Ice Production (on some models): The ice maker

should produce approximately 16 to 20 batches of ice in

a 24-hour period. If your refrigerator has the maximum ice

production feature, push the switch to MAX.

Remember

■ Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill the ice storage bin. Discard the first three

batches of ice produced.

■ The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

■ Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATOR

FEATURES

Your model may have some or all of these features.

Refrigerator Shelves

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

To remove and replace a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift back or front of the shelf past

the stop. Slide shelf out the rest of the way.

4. Replace the shelf by sliding the back of the shelf into the track

in the wall of the cabinet.

5. Guide the front of the shelf into the shelf track. Be sure to slide

the shelf in all the way.

Deli Drawer

To remove and replace the deli drawer:

1. Slide deli drawer out to the stop.

2. Lift front of deli drawer with one hand while supporting bottom

of drawer with other hand. Slide drawer out the rest of the

way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

NOTE: The deli drawer moves sideways on the shelf to allow

for flexible positioning.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish.........................use same day as purchased

Chicken, ground beef, variety meats (liver)......................1-2 days

Cold cuts, steaks/roasts ..................................................3-5 days

Cured meats...................................................................7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Crisper

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift the front

and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the stop.

Crisper Cover

To remove and replace the crisper cover:

1. Remove the crisper(s).

2. Pull the glass straight out.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

3. Replace the glass by pushing it straight in.

Crisper Humidity Control

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store in

a loosely closed paper bag on a refrigerator shelf.

■ Vegetables with skins: Place in plastic bag or plastic container

and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or tear off

bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

FREEZER FEATURES

Your model may have some or all of these features.

Wire Freezer Shelf

(on some models)

To remove and replace a wire shelf:

1. Remove the shelf by lifting the entire shelf slightly and moving

it all the way to the left-hand side. Tilt the right-hand side up

and out of the shelf supports.

2. Replace the shelf by inserting the left-hand end all the way

into the shelf supports. Then, lower the right-hand end of the

shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. If the

shelf does not appear stable, make sure both ends of the shelf are

inserted into the shelf supports.

Glass Freezer Shelf

(on some models)

To remove and replace a glass shelf:

1. Lift the front of the shelf to raise the shelf tabs up and out of

the opening in each shelf track. Slide the shelf out the rest of

the way.

2. Replace the shelf by tilting the back end downward to align

the back shelf tab under the track on each side of the freezer.

Gently push the shelf into the freezer until the two center shelf

tabs are positioned within the opening in each track. Lower

the shelf to rest on the shelf tracks.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Seal the package

or container securely to avoid taste and odor transfer throughout

the product. Ice crystals inside a sealed package are normal. This

simply means that moisture in the food and air inside the package

have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs of food per cubic foot [907 to

1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. The freezer door must

close tightly.

NOTE: For more information on preparing food for freezing, check

a freezer guide or reliable cookbook.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

DOOR FEATURES

Your model may have some or all of these features.

Door Rails

The door rails may be removed for easier cleaning.

Snap-on Door Rails (on some models)

To remove and replace the rails:

1. Depending on your model, remove the rails by pushing in

slightly on the front of the bracket while pulling out on the

inside tab. Repeat these steps for the other end.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket and

assembly onto the tabs above the shelf as shown.

Drop-in Door Rails (on some models)

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

Door Bins

(on some models)

To remove and replace the bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Utility Compartment

The utility compartment may be removed for easier cleaning.

To remove and replace the utility compartment:

1. Remove the utility compartment by squeezing against one

side while raising the utility compartment up and pulling it

straight out.

2. Replace the utility compartment by positioning one side in the

lock and sliding in the opposite side until it stops.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

■ Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid

odor transfer and drying out of food, wrap or cover foods

tightly.

■ For stainless steel models, stainless steel is corrosion-

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately to

avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

■ Remove the base grille.

■ Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■ Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

Changing the Light Bulbs

IMPORTANT: The light bulbs in both the refrigerator and freezer

compartments of your new refrigerator use LED technology. If the

lights do not illuminate when the refrigerator and/or freezer door is

opened, call for assistance or service. See Warranty for phone

numbers.

Refrigerator Compartment Light

The refrigerator light bulb is located behind the control.

1. Unplug refrigerator or disconnect power.

2. Remove the light shield by squeezing in on the sides and

pulling it straight down.

3. Remove the light bulb and replace it with an appliance bulb of

the same size and shape.

■ To replace an LED light bulb in the refrigerator

compartment, order part number W10565137 (3.6 watts).

NOTE: Some LED replacement bulbs are not

recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to

be wet/damp environments. If using a brand of LED bulb

other than the recommended LED bulb, before

installation, read and follow all instructions on the LED

packaging.

■ If an incandescent bulb is used to replace an LED bulb,

use only incandescent bulbs for household appliances

with a maximum of 60 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

Freezer Compartment Light (on some models)

1. Unplug refrigerator or disconnect power.

2. Remove the light shield (on some models).

■ Top of the freezer compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Remove the light bulb and replace it with an appliance bulb of

the same size and shape.

■ To replace an LED light bulb in the freezer compartment,

order part number W10574850 (2.0 watts).

NOTE: Some LED replacement bulbs are not

recommended for wet/damp environments. The

refrigerator and freezer compartments are considered to

be wet/damp environments. If using a brand of LED bulb

other than the recommended LED bulb, before

installation, read and follow all instructions on the LED

packaging.

■ If an incandescent bulb is used to replace an LED bulb,

use only incandescent bulbs for household appliances

with a maximum of 25 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

Vacation and Moving Care

Vacations

If You Choose to Leave the Refrigerator On While You’re

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Raise the wire shutoff arm to OFF (up) position.

4. Empty the ice bin.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Turn off the Temperature control(s). See “Using the Control(s).”

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■ Turn off the water supply to the ice maker at least one day

ahead of time.

■ Disconnect the water line from the back of the refrigerator.

■ When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See “Using the Control(s).”

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily OR raise the leveling screws so they don't

scrape the floor. See “Adjust the Door(s)” or “Door Closing

and Door Alignment.”

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the “Installation Instructions” section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

PROBLEM SOLVER

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code with your mobile device, or visit www.whirlpool.com/product_help.

In Canada, visit www.whirlpool.ca.

In the U.S.A.:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

Whirlpool Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

If you experience Possible Causes and/or Recommended Solutions

The refrigerator

will not operate

■ Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet. Do not use an

extension cord.

■ No power to the electrical outlet - Plug in a lamp to see if the outlet is working.

■ Household fuse blown or circuit breaker tripped - Replace the fuse or reset the circuit breaker. If the

problem continues, contact an electrician.

■ Control is not turned on - Turn the refrigerator control on.

■ New installation - Allow 24 hours following installation for the refrigerator to cool completely.

NOTE: Adjusting the temperature control(s) to coldest setting will not cool the refrigerator more quickly.

The motor seems

to run too much

Your new refrigerator may run longer than your old one. Energy efficient refrigerators run longer at lower, more

energy efficient speeds. Your refrigerator may run even longer if the room is warm, a large food load is added, the

door is opened often, or if the door has been left open.

The refrigerator is

noisy

Refrigerator noise has been reduced over the years. Due to this reduction in operating noise, you may notice

unfamiliar noises that are normal. Following are some normal sounds with an explanation:

■ Buzzing - heard when the water valve opens to fill the ice maker

■ Clicking/Snapping - valves opening or closing

■ Pulsating - fans/compressor adjusting to optimize performance

■ Rattling - flow of refrigerant, water line, or from items placed on top of the refrigerator

■ Sizzling/Gurgling - water dripping on the heater during defrost cycle

■ Popping - contraction/expansion of inside walls, especially during initial cool-down

■ Water running - may be heard when ice melts during the defrost cycle and water runs into the drain pan

■ Creaking/Cracking - occurs as ice is being ejected from the ice maker mold

The door will not

close completely

■ The door is blocked open - Move food packages away from door. Push bin or shelf back into the correct

position. Make sure the crisper cover is fully pushed in, so that the back rests on the supports.

The door is

difficult to open

■ Gaskets are dirty or sticky - Clean gaskets and contact surfaces with mild soap and warm water. Rinse and

dry with soft cloth.

Temperature is

too warm

■ New installation - Allow 24 hours following installation for the refrigerator to cool completely.

■ Door(s) opened often or not closed completely - Allows warm air to enter refrigerator. Minimize door

openings and keep doors fully closed.

■ A large amount of warm food has been recently added - Allow several hours for refrigerator to return to

normal temperature.

■ Check that the Temperature Control(s) are set correctly for the surrounding conditions - Adjust the

controls to one setting colder. Check temperature in 24 hours. See “Using the Control(s).”

There is interior

moisture buildup

NOTE: Some

moisture buildup is

normal.

■ Humid room - Contributes to moisture buildup in the refrigerator.

■ Door(s) opened often or not closed completely - Allows humid air to enter the refrigerator. Minimize door

openings and keep door fully closed.

The ice maker is

not producing ice

or not enough ice

(on some models)

■ The ice maker is not connected to a water supply - Connect refrigerator to water supply and turn water

shutoff valve fully open.

■ A kink in the line can reduce water flow - Straighten the water source line.

■ Ice maker is not turned on - Make sure the ice maker wire shutoff arm or switch (depending on model) is in

the ON position.

■ New installation - Wait 24 hours after ice maker installation for ice production to begin. Wait 3 days for full

ice production.

■ Large amount of ice recently removed - Allow sufficient time for ice maker to produce more ice.

■ Ice cube jammed in the ice maker ejector arm - Remove ice from the ejector arm with a plastic utensil.

■ A reverse osmosis water filtration system connected to your cold water supply can decrease water

pressure - See “Water Supply Requirements.”

The ice cubes are

hollow or small

(on some models)

NOTE: This is an

indication of low

water pressure.

■ The water valve is not completely open - Turn the water shutoff valve fully open.

■ A kink in the line can reduce water flow - Straighten the water source line.

■ A reverse osmosis water filtration system connected to your cold water supply can decrease water

pressure - See “Water Supply Requirements.”

■ If questions regarding water pressure remain, call a licensed, qualified plumber.

Off-taste, odor or

gray color in the

ice (on some

models)

■ New plumbing connections can cause discolored or off-flavored ice - Discard the ice and wash the ice

storage bin. Allow 24 hours for the ice maker to make new ice, and discard the first 3 batches of ice

produced.

■ Ice stored too long can develop an off-taste - Discard ice. Wash ice bin. Allow 24 hours for ice maker to

make new ice.

■ Food odor transferring to ice - Use airtight, moisture proof packaging to store food.

■ There are minerals (such as sulfur) in the water - A water filter may need to be installed to remove the

minerals.

If you experience Possible Causes and/or Recommended Solutions

ACCESSORIES

The following accessories are available for your refrigerator. To

order, contact us and ask for the Part Number.

In the U.S.A., visit our webpage www.whirlpool.com/

accessories or call 1-800-901-2042.

In Canada, visit our webpage www.whirlpoolparts.ca

or call 1-800-807-6777.

affresh

Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh

Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh

Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

1/14

WHIRLPOOL

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers

. In the U.S. and

Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

www.whirlpool.com/product_help

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase, when this major

appliance is installed, operated and maintained according to

instructions attached to or furnished with the product,

Whirlpool Corporation or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory Specified Replacement Parts

and repair labor to correct defects in materials or

workmanship that existed when this major appliance was

purchased, or at its sole discretion replace the product. In the

event of product replacement, your appliance will be

warranted for the remaining term of the original unit's warranty

period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a Whirlpool

designated service company. This limited warranty is valid

only in the United States or Canada and applies only when the

major appliance is used in the country in which it was

purchased. This limited warranty is effective from the date of

original consumer purchase. Proof of original purchase date is

required to obtain service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with

published user, operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes or correction of household electrical

or plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation

solutions, etc.).

5. Conversion of products from natural gas or L.P. gas.

6. Damage from accident, misuse, abuse, fire, floods, acts of God or use with

products not approved by Whirlpool.

7. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration or modification of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other damage to the

appliance finishes unless such damage results from defects in materials and

workmanship and is reported to Whirlpool within 30 days.

9. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive

environments including but not limited to high salt concentrations, high moisture or

humidity or exposure to chemicals.

10. Food or medicine loss due to product failure.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Whirlpool servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,

decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that

interfere with servicing, removal or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed, altered

or not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the

duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you

also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you

should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of

incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you

also may have other rights that vary from state to state or province to province.

La page charge ...