Briggs & Stratton Elite 01653 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: Elite 01653

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Portable Generator

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

EQUIPMENT

DESCRIPTION

Read this manual carefully and become

familiar with your generator.Know its

applications,its limitations and any hazards

involved.

The generators are an engine–driven, revolving field,

alternating current (AC) generator. It was designed to supply

electrical power for operating compatible electrical lighting,

appliances, tools and motor loads.The generator’s revolving

field is driven at about 3,600 rpm by a single-cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator” on page 11.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency. For

warranty information refer to the engine owner’s manual.

SAFETY RULES

This is the safety alert symbol.It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or serious

injury. WARNING indicates a hazard which, if not avoided,

could result in death or serious injury. CAUTION

indicates a hazard which, if not avoided, might result in

minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer,birth defects,or other reproductive harm.

WARNING

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

Portable Generator

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays around battery for a long

time after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

• Operate generator ONLY outdoors.

• Keep at least 2 feet of clearance on all sides of generator for

adequate ventilation.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground circuit fault interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

DANGER

• National Electric Code requires generator to be properly

grounded to an approved earth ground. Call an electrician for

local grounding requirements.

Failure to properly ground generator can result

in electrocution, especially if the generator is

equipped with a wheel kit.

DANGER

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing gas cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel

to spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property

damage.

WARNING

Portable Generator

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

WARNING

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator” on page 11.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or call

1-800-743-4115.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

Unintentional sparking can result in fire or

electric shock.

WARNING

Portable Generator

ASSEMBLY

Your generator requires some assembly and is ready for

use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the

model, revision, and serial number from the data tag available.

INSTALL WHEEL KIT

NOTE: If your unit is supplied with a 10” wheel kit use

the following instructions. If your unit is supplied with an

8” wheel kit use the instructions on page 6.

NOTE:While the wheel kit is designed to greatly improve

the portability of your generator, it is not intended for

over-the-road use.

You will need a socket wrench with 1/2" or 13mm sockets

and a needle-nose pliers to install this kit.

Install the 10” Wheel Kit as Follows

1. Place the bottom of the generator cradle on a flat,

even surface.Temporarily place unit on blocks to ease

assembly.

2. Slide axle through both axle mounting brackets on

cradle frame, as shown in Figure 1.

3. Slide a wheel over the axle.

NOTE: Be sure to install both wheels with the air

pressure valve on the outboard side.

4. Place the e-ring onto the groove in the axle.You may

add the flat washer if desired.

NOTE: Use retaining pins instead of e-clip, if applicable.

5. Place one end of the needle nose pliers on the bottom

of the axle and the other end of the pliers on top of

the e-ring. Seat the e-ring by pressing the pliers closed.

6. Repeat step 3 through 5 to secure second wheel.

7. Remove the temporary blocks.

8. Attach the vibration mounts to the support leg with

30mm capscrews and lock nuts.

9. To aid support leg assembly, rest generator on cradle,

engine end down. Remove the existing hardware from

the left unit vibration mount with 13mm wrench. Use

the same hardware to attach the support leg.

10. Attach the other side of the support leg with a 20mm

cap screw and lock nut. Rest generator on wheels and

support leg.

Portable Generator

11. If equipped, center the handle bracket on generator

frame at support leg end of cradle, as shown.

12. Attach handle bracket with two M8 x 45mm cap

screws and two locking hex nuts.

13. Check that all fasteners are tight and the tires are inflated

to the value marked on the tire or within 15 and 40 psi.

Install the 8” Wheel Kit as Follows

1. Place bottom of generator cradle on a flat surface.

2. Place axle stud through wheel retainer on cradle frame,

as shown in Figure 2.

3. Use 15/16” wrench to secure the axle stud to frame

with 5/8-18 jam nut.

4. Install the other axle stud in the same manner.

NOTE: Be sure to install wheel with raised hub inboard.

5. Tip unit and install the wheel. Place flat washer over

axle stud.

6. Retain wheel on axle stud with retaining pin. Install

other wheel on remaining axle shaft the same way.

7. Attach the vibration mount to the mounting leg with a

capscrew and lock nut.

8. Remove two front nuts from vibration mount on unit

with 13mm wrench. Use these nuts to retain the

mounting leg.

9. Center the lifting handle on generator end of cradle.

Attach the handle using two 13mm wrenches with two

capscrews and two hex nuts.

Capscrew

Handle

Grip

Nut

Mounting Leg

Use Existing Fasteners

to Secure Leg

Jam Nut

Retaining Pin

Wheel

Washer

Axle Stud

Figure 2 — Installing the Wheel Kit

Capscrew

Vibration Mount

Nut

Portable Generator

ELECTRIC START

Your unit may be equipped with electric start capability but

can be started manually. If you choose not to use the

electric start feature, you do not need to install the battery.

If your unit does not have electric start, ignore this section.

Check Battery / Attach Negative

Battery Wire

The sealed battery on the generator is fully charged and

pre–installed except for the negative (black) battery cable.

To install:

• Cut off tie wrap securing loose end of negative (black)

cable.

• Remove nut and washer on the negative battery terminal.

• Slide the negative battery cable over the screw on the

negative terminal (Figure 3).

• Reattach washer and nut and tighten.

• Verify that the connections to the battery and generator

are tight and secure.

BEFORE STARTING THE

ENGINE

Add Oil

CAUTION!Any attempt to crank or start the engine

before it has been properly filled with the recommended

oil may result in an engine failure.

To fill your engine with oil:

• Place generator on a level surface.

• Follow the oil grade recommendations and oil fill

instructions given in the engine owner’s manual.

NOTE:The generator’s revolving field rides on a

prelubricated and sealed ball bearing that requires no

additional lubrication for the life of the bearing.

Add Fuel

WARNING! NEVER fill fuel tank indoors. NEVER

fill fuel tank when engine is running or hot.Allow unit

to cool for two minutes before refueling. DO NOT

light a cigarette or smoke when filling the fuel tank.

WARNING! DO NOT overfill the fuel tank.

Always allow room for fuel expansion.

• Place generator on a level surface.

• Follow the fuel grade recommendations and fuel fill

instructions given in the engine owner’s manual.

Portable Generator

GROUNDING THE

GENERATOR

The National Electrical Code requires that the frame and

external electrically conductive parts of this generator be

properly connected to an approved earth ground. Local

electrical codes may also require proper grounding of the

unit. For that purpose, a GROUNDING FASTENER is

provided on the generator end (Figure 4).

Generally, connecting a No. 12 AWG (American Wire

Gauge) stranded copper wire to the grounding fastener and

to an earth–driven copper or brass grounding rod

(electrode) provides adequate protection against electrical

shock. Be careful to keep the grounding wire attached after

connecting the stranded copper wire. However, local codes

may vary widely. Consult with a local electrician for

grounding requirements in your area.

Properly grounding the generator helps prevent electrical

shock if a ground fault condition exists in the generator or

in connected electrical devices, especially when the unit is

equipped with a wheel kit. Proper grounding also helps

dissipate static electricity, which often builds up in

ungrounded devices.

BATTERY CHARGER

If equipped, use battery float charger jack to keep the

starting battery charged and ready for use. Battery charging

should be done in a dry location, such as inside a garage.

• Plug the charger into the unit’s “Battery Float Charger”

jack, which is located on the starter switch (Figure 5).

Plug battery charger into a 120 Volt AC wall receptacle.

• Unplug the charger from the unit and the wall outlet when

generator is being started and while it is in operation.

• Keep this charger plugged in when generator is not in

use to prolong battery life.The charger has a built in float

equalizer and will not overcharge the battery, even when

plugged in for an extended period of time.

IMPORTANT: See “Battery Maintenance” on page 12 for

additional information.

OPERATING THE

GENERATOR

CAUTION! NEVER start or stop the engine

with electrical loads connected to the receptacles

AND with the connected devices turned ON.

IMPORTANT:Always unplug the battery float charger

before starting the generator.

Starting the Engine

Disconnect all electrical loads from the generator. Use the

following start instructions:

• For models with the fuel valve built into the engine, turn

the fuel valve to the “On” position (Figure 6).

• For models with an overhead fuel tank, turn the fuel

valve to the “On” position (Figure 7).The fuel valve

handle should be vertical (pointing toward the ground)

for fuel to flow.

• Start the engine according to instructions given in the

engine owner’s manual.

Figure 4 — Grounding Fastener

Grounding

Fastener

Figure 5 — Battery Charger Jack

Fuel Valve is shown

in the On position

Figure 7 — Fuel Valve

Fuel Valve is

shown in the

On position

Figure 6 — Fuel Valve

Portable Generator

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR.See

“Don’t Overload the Generator” on page 11.

Stopping the Engine

• Unplug all electrical loads from generator panel

receptacles. Never start or stop engine with electrical

devices plugged in and turned ON.

• Let engine run at no-load for several minutes to stabilize

the internal temperatures of engine and generator.

• Turn engine off according to instructions given in the

engine owner’s manual.

• Move the fuel valve to the “Off” position.

RECEPTACLES

The generator will be equipped with one or more of the

following receptacles:

120/240 Volt AC, 30 Amp, Locking

Receptacle

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater) (Figure 8).You can use the same 4–wire cord if you

plan to run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 6,000 watts of power (6.0 kW)

at 30 Amps for 120 Volts or 240 Volts.The outlet is

protected by a push–to–reset circuit breaker.

CAUTION!Although this outlet states it has a

120/240 Volt 30 Amp rating (up to 7,200 watts), the

generator may only be rated for up to 6,000 watts.

Powering loads that exceed the wattage/amperage

capacity of the generator can damage it or cause

serious injuries.

120 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L5-30 plug with this receptacle. Connect a

3-wire cord set rated for 125 Volts AC at 30 Amps to the

plug (Figure 9).

Use this receptacle to operate 120 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts (3.6 kW) of power

at 30 Amps.The outlet is protected by a push-to-reset

circuit breaker.

CAUTION!Although this outlet is rated for

120 Volt 30 Amp (up to 3,600 watts), the generator

may only be rated for 3,250 watts at 27 Amps.

Powering loads that exceed the wattage/amperage

capacity of the generator can damage it or cause

serious injuries.

Figure 8 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

Figure 9 — 120 Volt AC, 30 Amp, Locking Receptacle

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

Portable Generator

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that

all periodic maintenance tasks are completed on a timely

basis; that all discrepancies are corrected; and that the unit

is kept clean and properly stored. NEVER operate a

damaged or defective generator.

Engine Maintenance

See engine owner’s manual for instructions.

CAUTION!Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has

been shown to cause skin cancer in certain

laboratory animals.Thoroughly wash exposed areas

with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with snow,

leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air slots,

some of the water will be retained in voids and cracks of

the rotor and stator winding insulation.Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Battery Maintenance

Other than float charging, described elsewhere, no

maintenance is required for the starting battery. Keep the

battery and terminals clean and dry.

IMPORTANT: Battery charging should be performed in a

dry location, such as inside a garage.

To Clean the Generator

CAUTION! NEVER insert any object or tool

through the air cooling slots, even if the engine is

not running.

• Use a damp cloth to wipe exterior surfaces clean.

• A soft bristle brush may be used to loosen caked on dirt

or oil.

• A vacuum cleaner may be used to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and opening on

generator.These openings must be kept clean and

unobstructed.

Portable Generator

STORAGE

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than

30 days, use the following guidelines to prepare it for

storage.

Generator Storage

• Clean the generator as outlined in “To Clean the

Generator.”

• Check that cooling air slots and openings on generator

are open and unobstructed.

CAUTION! Storage covers can be flammable.

DO NOT place a storage cover over a hot

generator. Let the unit cool for a sufficient time

before placing the cover on the unit.

Engine Storage

See engine owner’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, add fuel stabilizer into fuel

tank and fill with fresh fuel. Run the unit for several

minutes to circulate the additive through the carburetor.

The unit and fuel can then be stored for up to

24 months. Fuel stabilizer can be purchased locally.

• Do Not store fuel from one season to another unless it

has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it's used with this unit.

• Store unit in a clean and dry area.

Portable Generator

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC EQUIPMENT OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s), of the equipment that is defective in material or

workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser.

This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized

Service Dealer in our dealer locator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL

IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE

EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and

some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion

may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country

to country.

OUR EQUIPMENT*

OUTBOARD

MOTOR

PRESSURE

WASHER

WATER PUMP

(Not available in the

USA)

PORTABLE

GENERATOR

Less tthan 110 KKW 10 KKW oor ggreater

TRANSFER

SWITCH

2 years

none

1 year

90 days

1 year

90 days

2 years

1 year

2 years

1 year

3 years or

1500 hours

1 year

WARRANTY PERIOD**

HOME GENERATOR SYSTEM

(Includes Transfer Switch, if sold with equipment.)

Consumer Use

Commercial Use

* The engine and starting batteries are warranted solely by the manufacturers of those products.

** 2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and

Home Generator System - Less than 10 KW, outside of European Union.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in

the table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including

use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as

commercial use for purposes of this warranty. Equipment used for Prime Power in place of utility are not applicable to this warranty. Electric

Powered Pressure Washers used for commercial purposes are not warranted.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF

PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS

REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR EQUIPMENT WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered

or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to

be defective under normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not

cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,

in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).

• Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that

have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing

or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. Also

excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in

life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Génératrice portative

LORSQUE VOUS AJOUTEZ DU CARBURANT

• Éteignez le générateur et laissez-le refroidir au moins 2 minutes avant

de retirer le capuchon du réservoir de carburant. Desserrez lentement

le capuchon pour laisser la pression s'échapper du réservoir.

• Remplissez toujours le réservoir à essence à l'extérieur.

• NE REMPLISSEZ PAS trop le réservoir. Laissez 1,5 pouce pour

l'expansion de l'essence.

• Éloignez l'essence des étincelles, des flammes, des veilleuses, de la

chaleur et de toute autre source d'inflammation.

• N'ALLUMEZ PAS de cigarette ou ne fumez pas à proximité de l'appareil.

LORSQUE L'ÉQUIPEMENT FONCTIONNE

• NE PENCHEZ PAS le moteur ou l'équipement, vous risqueriez de

renverser de l'essence.

• Cette génératrice n'est pas conçue pour être utilisée dans de

l'équipement mobile ou les applications marines.

LORSQUE VOUS TRANSPORTEZ OU RÉPAREZ

L'ÉQUIPEMENT

• Transportez ou réparez l'appareil lorsque le réservoir d'essence est

VIDE, ou lorsque la soupape d'arrêt d'essence est FERMÉE.

• Débranchez le câble de bougie.

LORSQUE VOUS ENTREPOSEZ L'ESSENCE OU UN

ÉQUIPEMENT AVEC UN RÉSERVOIR À ESSENCE

• Entreposez-le loin des appareils de chauffage, des fours, des chauffe-

eau, des sécheuses ou de tout autre appareil électroménager

disposant d'une veilleuse ou de toute autre source d'inflammation

risquant d'enflammer les vapeurs d'essence.

L'essence et ses vapeurs sont extrêmement

inflammables et explosives.

Le feu ou l'explosion risque de provoquer des

blessures graves, pouvant être fatales.

AVERTISSEMENT

• Ne laissez aucune flamme, étincelle, source de chaleur ou cigarette

allumée pendant ou plusieurs minutes suivant la charge de

l'accumulateur.

• Portez des lunettes de protection, un tablier et des gants en caoutchouc.

Les batteries d'accumulateur produisent du gaz

hydrogène explosif lorsqu'elles se rechargent.

Le gaz hydrogène stagne autour de la batterie

longtemps après qu'elle ait été chargée.

La plus petite étincelle enflammera l'hydrogène et

provoquera une explosion.

Vous pouvez devenir aveugle ou vous blesser gravement.

Le liquide d'électrolyte de l'accumulateur contient de

l'acide et est extrêmement caustique.

Le contact avec le liquide de l'accumulateur

provoquera de graves brûlures chimiques.

DANGER

• Faites fonctionner le générateur SEULEMENT à l'extérieur.

• Laissez un espace d'au moins 2 pieds tout autour du générateur, pour

permettre une ventilation adéquate.

• NE FAITES PAS fonctionner le générateur à l'intérieur d'un bâtiment

ou d'un abri, y compris à l'intérieur du compartiment d'un véhicule de

plaisance.

Le générateur, lorsqu'il fonctionne, produit du monoxyde

de carbone, un gaz toxique inodore et incolore.

Le fait de respirer du monoxyde de carbone provoque

des nausées, des évanouissements ou peut être fatal.

DANGER

• Le Code national de l'électricité requiert que le générateur soit

correctement relié à la terre par un branchement homologué. Faites appel

à un électricien pour connaître les exigences de mise à la terre régionales.

Si la génératrice n'est pas mise à la masse comme il

se doit, il y a risque d'électrocution, particulièrement

si la génératrice est équipée de roues.

DANGER

• Lorsque vous utilisez le générateur comme source d'énergie de

secours, il est nécessaire d'aviser les services publics d'électricité.

• Utilisez un disjoncteur différentiel lorsque vous utilisez l'appareil dans

des endroits humides ou extrêmement conductibles, comme les

terrasses en métal ou les ouvrages métalliques.

• NE touchez pas les fils dénudés ou les boîtiers.

• N'UTILISEZ pas le générateur avec des cordons électriques usés,

effilochés ou dénudés, ou abîmés de quelque sorte que ce soit.

• N'UTILISEZ pas le générateur sous la pluie.

• NE manipulez pas le générateur ou les cordons d'alimentation lorsque

vous êtes debout dans l'eau, pieds nus ou avec les mains ou les pieds

humides.

• NE laissez pas des personnes non qualifiées ou des enfants se servir

ou réparer le générateur.

Le générateur produit une tension élevée.

Ne pas isoler le générateur de l'installation électrique

risque de provoquer des blessures ou même d'être fatal

pour les ouvriers électriciens et de causer des dommages

au générateur dus à un "backfeed" d'énergie électrique.

DANGER

• Cette génératrice ne satisfait pas aux normes U. S. Coast Guard

Regulation 33CFR-183 et ne doit pas être utilisée pour des

applications marines.

• L'omission d'utiliser une génératrice appropriée et approuvée par U. S.

Coast Guard pourrait entraîner des blessures corporelles ou des

dommages matériels.

AVERTISSEMENT

Génératrice portative

LORSQUE VOUS RÉGLEZ OU RÉPAREZ VOTRE

GÉNÉRATEUR

• Débranchez toujours le câble de bougie et placez-le de façon à ce

qu'il ne soit pas en contact avec la bougie.

Unintentional peut résulter dans feu ou électrique.

AVERTISSEMENT

• NE TOUCHEZ PAS les surfaces chaudes.

• Laissez l'équipement refroidir avant de le toucher.

Les moteurs en fonctionnement produisent de la chaleur.

La température du silencieux et des endroits à proximité

peuvent atteindre, voire dépasser 150°F (65°C).

Le contact de ces pièces risque de causer de graves brûlures.

AVERTISSEMENT

• NE TRAFIQUEZ PAS la vitesse régulée. Le générateur produit une

fréquence nominale et une tension correctes lorsqu'il fonctionne à

une vitesse régulée.

• NE modifiez le générateur d'aucune façon.

Les vitesses de fonctionnement excessivement élevées

augmentent les risques de blessure ou risquent d'endommager

le générateur.

Les vitesses extrêmement lentes entraînent une charge importante.

ATTENTION

• Voir la section " Ne surchargez pas votre générateur " à la page 25.

• Démarrez le générateur et laissez le moteur se stabiliser avant de

brancher les charges électriques.

• Branchez les charges électriques en position ARRÊT, puis, remettez en

position MARCHE.

• Éteignez les charges électriques et débranchez-les du générateur avant

de l'arrêter.

Dépasser la capacité de puissance ou d'ampérage du

générateur risque d'endommager ce dernier et/ou les autres

appareils électriques qui y sont branchés.

ATTENTION

• NE vous servez du générateur que pour les utilisations prévues.

• Si vous avez des questions concernant les utilisations prévues,

demandez à votre distributeur ou contactez Négociant autorisé.

• Ne faites fonctionner le générateur que sur des surfaces horizontales.

• N'EXPOSEZ pas le générateur à une humidité excessive, à de la

poussière, à de la saleté ou à des vapeurs corrosives.

• N'INSÉREZ aucun objet dans les fentes de refroidissement.

• Si les appareils branchés sont en surchauffe, éteignez-les et

débranchez-les du générateur.

• Arrêtez le générateur si :

-la puissance électrique est inexistante;

-l'équipement produit des étincelles, de la fumée ou des flammes;

-l'unité vibre excessivement.

Un traitement inapproprié du générateur risque de

l'endommager et de raccourcir sa durée d'utilisation.

ATTENTION

Génératrice portative

ASSEMBLAGE

Votre générateur exige que quelque assemblée et soit prêt pour

l'usage après il a été convenablement entretenu avec le pétrole et

le carburant recommandés.

Si vous avez n'importe quels problèmes avec l'assemblée de votre

générateur, s'il vous plaît appeler le helpline de générateur à

1-800-743-4115.Si vous téléphonez pour obtenir de l'aide,

veuillez avoir disponibles les renseignements du données

étiquettent: numéro de modèle, de révision et de série.

INSTALLE LA ROUE LA TROUSSE

REMARQUE: Si votre appareil est doté de roues de 25 cm

(10 po), veuillez suivre les instructions ci-dessous. Si votre appareil

est doté de roues de 20 cm (8 po), veuillez suivre les instructions

à la page 20.

Les roues ont été conçues pour améliorer la portabilité de votre

génératrice.

REMARQUE: Les roues n'ont pas été conçues pour le transport

de la génératrice sur la route.

Pour installer cet ensemble, vous aurez besoin d'une clé munie de

douilles de 1/2 po ou de 13 mm ainsi que de pinces à becs fins.

Installez les roues de 25 cm (10 po) comme suit (figure 13)

1. Placez le fond du berceau de la génératrice sur une surface

plate et unie. Pour faciliter l'assemblage, placez

temporairement l'appareil sur des blocs.

2. Faites glisser l'essieu dans les deux supports de fixation de

l'essieu sur le cadre du berceau, tel qu'illustré à la figure 13.

3. Faites glisser une roue sur l'essieu.

REMARQUE:Assurez-vous de poser les deux roues avec la

valve à pneu pointant vers l'extérieur.

4. Posez l'anneau en E sur la rainure de l'essieu. Posez la

rondelle plate si vous le désirez.

REMARQUE: Le cas échéant, utilisez des tiges de retenue au

lieu d'anneaux en E.

5. Placez un bout des pinces à becs fins au-dessous de l'essieu

et l'autre bout au-dessus de l'anneau en E. Bloquez l'anneau

en E en serrant les pinces.

6. Répétez les étapes 3 à 5 pour la pose de la deuxième roue.

7. Enlevez les blocs temporaires.

8. Fixez les montants antivibratiles à la tige portante avec des

vis à tête de 30 mm et des contre-écrous.

9. Pour faciliter la pose de la tige portante, faites reposer la

génératrice sur le berceau avec l'extrémité moteur vers le

bas. Enlevez les pièces de fixation déjà installées sur le

montant antivibratile gauche à l'aide d'une clé de 13 mm.

Utilisez ces pièces pour fixer la tige portante.

10. Fixez l'autre côté de la tige portante avec une vis à tête de

20 mm et un contre-écrou. Faites reposer la génératrice sur

les roues et la tige portante.

Tige portante

Écrou hexagonal

Essieu

Rondelle plate

Vis à tête

Ensemble de poignée

Écrou hexagonal

Roue

Anneau en E

Figure 13 — Installe la roue la trousse

Vis à tête

Écrou hexagonal

Vis à tête

Montant antivibratile

Utilisez les pièces de

fixation fournies pour

fixer le côté gauche de la

tige portante à l'appareil

Génératrice portative

11. Centrez le support de la poignée sur le cadre de la génératrice

côté tige portante du berceau, tel qu'indiqué dans l'illustration.

12. Fixez le support de la poignée à l'aide de deux vis d'assemblage

M8 x 45 mm et de deux contre-écrous hexagonaux.

13. Assurez-vous que chaque fixation est solide et que la

pression des pneus se situe entre 15 et 40 lb/po2.

Installez les roues de 20 cm (8 po) comme suit (figure 14)

1. Placez le fond du berceau de la génératrice sur une surface plate.

2. Enfilez le goujon de l'essieu dans le dispositif de retenue du

cadre du berceau.

3. Utilisez une clé de 24 mm (15/16 po) pour fixer le goujon de

l'essieu au cadre avec un contre-écrou de 5/8-18.

4. Posez l'autre goujon d'essieu de la même manière.

REMARQUE:Assurez-vous de placer la roue avec le moyeu

surélevé du côté intérieur.

5. Inclinez l'appareil et posez la roue. Posez une rondelle plate

sur le goujon d'essieu.

6. Fixez la roue au goujon d'essieu avec une tige de retenue.

Installez l'autre roue sur l'autre arbre d'essieu de la même

manière.

7. Fixez le montant antivibratile à la tige portante avec une vis à

tête et un contre-écrou.

8. Enlevez les deux écrous avant du montant antivibratile à

l'aide d'une clé de 13 mm. Utilisez ces écrous pour fixer la

tige portante.

9. Centrez la poignée de levage à l'extrémité génératrice du

berceau. À l'aide de deux clés de 13 mm, fixez la poignée

avec deux vis à tête et deux écrous hexagonaux.

Vis à tête

Poignée

Prise

Écrou

Tige portante

Utilisez les attaches

fournies pour fixer la tige

Contre-écrou

Tige de retenue

Roue

Rondelle

Goujon d'essieu

Figure 14 —

Installe la roue la trousse

Vis à tête

Montant antivibratile

Écrou

La page charge ...

Briggs & Stratton Elite 01653 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: Elite 01653

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton Elite 01653 User manual
español: Briggs & Stratton Elite 01653 Manual de usuario

Briggs & Stratton Elite 01653 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton Elite 01653 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents