LG GL-B402RPHR Le manuel du propriétaire

P/NO : MFL68489001

ENGLISH

FRENCH

ARABIC

3

10

11

13

22

23

25

27

Lamp Replacement

Green Ion Door Cooling /

Ice Beam Door Cooling (Optional)

Inverter On feature (Optional)

WARNING

Keep ventilation openings, in the appliance enclosure or in

the built-in-structure, clear of obstruction.

Do not use mechanical devices or other means to accelerate

the defrosting process, other than those recommended by the

manufacturer.

Do not damage the refrigerant circuit.

Do not use electrical appliances inside the food storage

compartment, unless they are recommended by the

manufacturer.

The refrigerant and insulation blowing gas used in the

appliance requires special disposal procedures. When

disposal, please consult with services agent or a similarly

qualified person.

This appliance contains a small amount of isobutane refrigerant

(R600a), natural gas with high environmental compatibility, but it is

also combustible. When transporting and installing the appliance,

care should be taken to ensure that no parts of the refrigerating

circuit are damaged. Refrigerant squirting out of the pipes could

ignite or cause an eye injury. If a leak is detected, avoid any naked

flames or potential sources of ignition and air the room in which the

appliance is standing for several minutes.

Never startup an appliance showing any signs of damage. If in

doubt, consult your dealer.

If gas used is R600a

Do not use or store

inflammable materials like

ether, benzene, alcohol,

medicine, LP gas, spray or

cosmetics

near or in the

refrigerator.

It may cause

explosion or fire.

Inverter-On feature (Optional)

Minimum requirement: UPS/ Inverter

should be in ON condition having

minimum 600VA capacity along with

minimum 120Ah capacity battery

connected with the refrigerator’s

power supply socket.

Green Ion Door

Cooling / Ice

Beam Door

Cooling (Optional)

When the Freezer compartment is not enough cold in winter, adjust the control for the freezer to High

(4/5/ ● / )

For achieving temperature in Freezing , Energy and Storage Test, Freezer control may be required to set at

“●” or “●●”

●●

‘3’ or ‘4’

GREEN ION DOOR COOLING / ICE BEAM DOOR

COOLING (OPTIONAL)

Use this function when calling the Customer Call Centre and receive precise diagnosis when the

Refrigerator malfunctions or fails. Use it only when advised by the consultant and not otherwise.

SMART DIAGNOSIS (Only for Selected External Micom Models)

1. Open all the doors of the refrigerator.

2. Press the refrigerator control (REF

TEMP) button for 3 sec or more.

3. If the buzzer sounds 4 times (Frequency

of SDS Buzzer is 2000Hz, 0.2sec Off/

0.2sec On 4 times) place the phone near

the speaker hole in the top right hand

side door hinge.

4. Ensure the microphone of the

telephone is towards the speaker hole.

CAUTION

The transmission sound may be irritating.

Do not take away the telephone until the sound

stops for good diagnosis.

Smart diagnosis function is...

Use this function when calling the Customer Call Centre and receive precise diagnosis when the

Refrigerator malfunctions or fails. Use it only when advised by the consultant and not otherwise.

How to use the function

Be aware!

Difference of the regional call qualities may have influence on the function.

If you use home phone, better communication performance will enable much better service.

Smart diagnosis data transmission may not be successful if the call is made from a mobile phone

with poor network reception.

First, call LG service center. Only use the Smart Diagnosis feature when instructed to do so by the LG

call center agent.

5. Do not take away the telephone while

data is being transmitted.

6. During the data transmission for smart

diagnosis, hold the telephone 10cm

away from the speaker hole and avoid

any background noises. After inputting

SDS, SDS buzzer will ring. After

completion of the data transmission,

the consultant will explain the result of

the smart diagnosis and advice

a c c o r d i n g l y. W h e n t h e d a t a

transmission is completed, the

refrigerator will be automatically turned

off and on a few seconds later.

SMART DIAGNOSIS (Only for Selected Internal Micom Models)

LED PATTEN DURING INVERTER-ON MODE (OPTIONAL)

During the use of this feature, you will find this pattern of LED running. It is a symbol

that the product is running at basic energy requirement. One can press the button “REF

TEMP” to change the LED setting during power cuts, if needed. The LED will then show

the setting as desired. When the mode is changed from Normal supply to Inverter mode

& vice versa, the LED pattern will take some time to display the change.

La page charge ...

LG GL-B402RPHR Le manuel du propriétaire

LG GL-B402RPHR Le manuel du propriétaire

Documents connexes