Wacker Neuson BH 65 28x152 US Manuel utilisateur

Taper
Manuel utilisateur
5100010465 01 0214
Operator’s Manual
Gasoline Demolition Hammer
BH 55, 65
Notice d’Emploi
Marteau thermique
5100010465
Manufacturer
Wacker Neuson Produktion GmbH & Co. KG
Preußenstraße 41
80809 München
www.wackerneuson.com
Tel.: +49-(0)89-354 02-0
Fax: +49-(0)89-354 02-390
Translation of the original operator's manual in German
5100004583IVZ.fm 3
1 Foreword ....................................................................................................................5
2 Introduction ...............................................................................................................6
2.1 Means of representation for this operator's manual....................................................... 6
2.2 Wacker Neuson representative...................................................................................... 7
2.3 Described machine types............................................................................................... 7
2.4 Identification of the machine .......................................................................................... 8
3 Safety .........................................................................................................................9
3.1 Principle ......................................................................................................................... 9
3.2 Qualification of the operating personnel....................................................................... 12
3.3 Protective gear............................................................................................................. 13
3.4 Transport...................................................................................................................... 14
3.5 Operating safety........................................................................................................... 15
3.6 Safety during the operation of hand machines............................................................. 17
3.7 Safety during the operation of combustion engines..................................................... 17
3.8 Maintenance................................................................................................................. 19
3.9 Safety devices.............................................................................................................. 21
4 Safety and information labels ................................................................................22
5 Scope of delivery ....................................................................................................24
6 Structure and function ...........................................................................................25
6.1 Application.................................................................................................................... 25
6.2 Functional description .................................................................................................. 25
6.3 Variants........................................................................................................................ 25
7 Components and operator's controls ................................................................... 26
8 Transport ................................................................................................................. 28
9 Initial start up ..........................................................................................................30
10 Use and operation ................................................................................................... 31
10.1 Prior to starting the machine ........................................................................................ 31
10.2 Adjusting the machine.................................................................................................. 32
10.3 Changing tools ............................................................................................................. 33
10.4 Starting up.................................................................................................................... 34
10.4.1 Starting the engine.......................................................................................... 35
10.5 Operating the machine................................................................................................. 38
10.6 Decommissioning......................................................................................................... 39
11 Maintenance ............................................................................................................40
11.1 Maintaining the Emission control system..................................................................... 40
11.2 Maintenance personnel qualifications.......................................................................... 40
11.3 Maintenance schedule ................................................................................................. 41
Inhalt
4
5100004583IVZ.fm
11.4 Maintenance work ........................................................................................................ 41
11.4.1 Cleaning machine............................................................................................ 42
11.4.2 Topping up with fuel ........................................................................................ 42
11.4.3 Checking/cleaning air cleaner ......................................................................... 43
11.4.4 Lubricating the machine .................................................................................. 44
11.4.5 Checking/cleaning/replacing spark plug .......................................................... 45
11.4.6 Checking the tool holder for wear.................................................................... 46
12 Malfunctions ............................................................................................................ 47
13 Storage ..................................................................................................................... 48
14 Accessories .............................................................................................................49
14.1 Truck............................................................................................................................. 49
15 Technical data .........................................................................................................51
15.1 BH 55............................................................................................................................ 51
15.2 BH 55rw........................................................................................................................ 55
15.3 BH 65............................................................................................................................ 59
15.4 Combustion engine....................................................................................................... 63
16 Emission Control Systems Information and Warranty ........................................ 64
16.1 Emission Control System Background Information ...................................................... 64
16.2 Limited Defect Warranty for Wacker Neuson Emission Control Systems .................... 65
17 Glossary ................................................................................................................... 70
17.1 Use of oxygenated fuels............................................................................................... 70
EC Declaration of Conformity ................................................................................71
EC Declaration of Conformity ................................................................................73
EC Declaration of Conformity ................................................................................75
DIN EN ISO 9001 Zertifikat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1 Foreword
100_0000_0002.fm 5
1Foreword
This operator's manual contains information and procedures for the safe opera-
tion and maintenance of your Wacker Neuson machine. In the interest of your
own safety and to prevent accidents, you should carefully read through the safety
information, familiarize yourself with it and observe it at all times.
This operator's manual is not a manual for extensive maintenance and repair
work. Such work should be carried out by Wacker Neuson service or authorized
specialists.
The safety of the operator was one of the most important aspects taken into con-
sideration when this machine was designed. Nevertheless, improper use or in-
correct maintenance can pose a risk. Please operate and maintain your Wacker
Neuson machine in accordance with the instructions in this operator's manual.
Your reward will be troublefree operation and a high degree of availability.
Defective machine parts must be replaced immediately!
Please contact your Wacker Neuson representative if you have any questions
concerning operation or maintenance.
All rights reserved, especially reproduction and distribution rights.
Copyright 2014 Wacker Neuson Produktion GmbH & Co. KG
No part of this publication may be reproduced in any form or by any means, elec-
tronic or mechanical, including photocopying, without the expressed written per-
mission of Wacker Neuson.
Any type of reproduction, distribution or storage on data media of any type and
form not authorized by Wacker Neuson represents an infringement of copyright
and will be prosecuted.
We expressly reserve the right to make technical modifications – even without
special notice – which aim at further improving our machines or their safety stan-
dards.
2 Introduction
6
100_0000_0003.fm
2 Introduction
2.1 Means of representation for this operator's manual
Warning symbols
This operator's manual contains safety information of the categories:
DANGER, WARNING, CAUTION, NOTICE.
They should be followed to prevent danger to life and limb of the operator or dam-
age to equipment and exclude improper service.
Notes
Note: Complementary information will be displayed here.
DANGER
This warning notice indicates immediate hazards that result in serious injury or
even death.
X Danger can be avoided by the following the actions mentioned.
WARNING
This warning notice indicates possible hazards that can result in serious injury
or even death.
X Danger can be avoided by the following the actions mentioned.
CAUTION
This warning notice indicates possible hazards that can result in minor injury.
X Danger can be avoided by the following the actions mentioned.
NOTICE
This warning notice indicates possible hazards that can result in material dam-
age.
X Danger can be avoided by the following the actions mentioned.
2 Introduction
100_0000_0003.fm 7
Instructions
X This symbol indicates there is something for you to do.
1. Numbered instructions indicate that you have to carry out something in a de-
fined sequence.
This symbol is used for lists.
2.2 Wacker Neuson representative
Depending on your country, your Wacker Neuson representative is your Wacker
Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.
You can find the addresses in the Internet at www.wackerneuson.com.
The address of the manufacturer is located at the beginning of this operator's
manual.
2.3 Described machine types
This operator's manual is valid for different machine types from a product range.
Therefore some figures can differ from the actual appearance of your machine.
It is also possible that the descriptions include components which are not a part
of your machine.
Details for the described machine types can be found in the chapter Technical
data.
2 Introduction
8
100_0000_0003.fm
2.4 Identification of the machine
Nameplate data
The nameplate lists information that uniquely identifies your machine. This infor-
mation is needed to order spare parts and when requesting additional technical
information.
X Enter the information of your machine into the following table:
Item Designation Your information
1 Group and type
2 Construction year
3 Machine no.
4 Version no.
5 Item no.
3 Safety
100_0302_si_0001.fm 9
3 Safety
3.1 Principle
State of the art
This machine has been constructed with state-of-the-art technology according to
the recognized rules of safety. Nevertheless, when used improperly, dangers to
the life and limb of the operator or to third persons or damage to the machine or
other materials cannot be excluded.
Proper use
The machine must only be used for the following purposes:
Breaking off concrete and asphalt and soil that is full of boulders.
Breaking off concrete, masonry and other construction materials, untouched
and frozen ground.
Scarifying roads and concrete, asphalt, tar and wooden and stone paving.
Cutting clay, loam, peat and salts.
Breaking up compacted soils.
Ramming in posts, probes and grounding rods.
To tamp sleepers in track construction.
The machine may only be used with tools that are intended for use with the ma-
chine and the material being worked on.
The machine may not be used for the following purposes:
Working on hazardous materials such as asbestos.
Its proper use also includes the observance of all instructions contained in this
operator's manual as well as complying with the required service and mainte-
nance instructions.
Any other use is regarded as improper. Any damage resulting from improper use
will void the warranty and the liability on behalf of the manufacturer. The operator
assumes full responsibility.
3Safety
10
100_0302_si_0001.fm
Structural modifications
Never attempt to modify the machine without the written permission of the man-
ufacturer. To do so will endanger your safety and the safety of other people! In
addition, this will void the warranty and the liability on behalf of the manufacturer.
Especially the following are cases of structural modifications:
Opening the machine and the permanent removal of components from
Wacker Neuson.
Installing new components which are not from Wacker Neuson and not equiv-
alent to the original parts in design and quality.
Installation of accessories which are not from Wacker Neuson.
It is no problem to install spare parts from Wacker Neuson.
It is no problem to install accessories that are available in the Wacker Neuson
product range of your machine. Please refer to the installation regulations in this
operator's manual.
Do not drill into the housing, e.g. to install signs. Water could penetrate the hous-
ing and damage the machine.
Requirements for operation
The ability to operate the machine safely requires:
Proper transport, storage and setup.
Careful operation.
Careful service and maintenance.
Operation
Operate the machine only as intended and only when in proper working condi-
tion.
Operate the machine in a safety-conscious manner with all safety devices at-
tached and enabled. Do not modify or disable any safety devices.
Before starting operation, check that all control and safety devices are function-
ing properly.
Never operate the machine in a potentially explosive environment.
Maintenance
Regular maintenance is required in order for the machine to operate properly and
reliably over time. Failure to perform adequate maintenance reduces the safety
of the machine.
Strictly observe the prescribed maintenance intervals.
Do not use the machine if it requires maintenance or repairs.
3 Safety
100_0302_si_0001.fm 11
Malfunctions
If you detect a malfunction, you must shut down and secure the machine imme-
diately.
Eliminate the malfunctions that impair safety immediately!
Have damaged or defective components replaced immediately!
For further information, refer to chapter Malfunctions.
Spare parts, accessories
Use only spare parts from Wacker Neuson or such that are equivalent to the orig-
inal parts in design and quality.
Only use accessories from Wacker Neuson.
Non-compliance will exempt the manufacturer from all liability.
Exclusion of liability
Wacker Neuson will refuse to accept liability for injuries to persons or for damage
to materials in the following cases:
Structural modifications.
Improper use.
Failure to comply with this operator's manual.
Improper handling.
Using of spare parts which are not from Wacker Neuson and not equivalent
to the original parts in design and quality.
Using of accessories which are not from Wacker Neuson.
Operator's manual
Always keep the operator's manual near the machine or near the worksite for
quick reference.
If you have misplaced the operator's manual or require an additional copy, con-
tact your Wacker Neuson representative or download the operator's manual from
the Internet (www.wackerneuson.com).
Always hand over this operator's manual to other operators or to the future owner
of the machine.
Country-specific regulations
Observe the country-specific regulations, standards and guidelines in reference
to accident prevention and environmental safety, for example those pertaining to
hazardous materials and wearing protective gear.
Complement the operator's manual with additional instructions taking into ac-
count the operational, regulatory, national or generally applicable safety guide-
lines.
3Safety
12
100_0302_si_0001.fm
Operator's controls
Always keep the operator's controls of the machine dry, clean and free of oil or
grease.
Operating elements such as ON/OFF switch, gas handles etc. may not be
locked, manipulated or changed without authorization.
Checking for signs of damage
Inspect the machine when it is switched off for any signs of damage at least once
per work shift.
Do not operate the machine if there is visible damage or defects.
Have any damage or defects eliminated immediately.
Supervision
Never leave the machine running unattended!
3.2 Qualification of the operating personnel
Operator qualifications
Only trained personnel are permitted to start and operate the machine. The fol-
lowing rules also apply:
You are physically and mentally fit.
You have received instruction on how to independently operate the machine.
You have received instruction in the proper use of the machine.
You are familiar with required safety devices.
You are authorized to start machines and systems in accordance with the
standards governing safety.
Your company or the operator has assigned you to work independently with
this machine.
Incorrect operation
Incorrect operation or misuse by untrained personnel can endanger the health
and safety of the operator or third persons and also cause machine and material
damage.
Operating company responsibilities
The operating company must make the operator's manual available to the oper-
ator and ensure that the operator has read and understood it.
3 Safety
100_0302_si_0001.fm 13
Work recommendations
Please observe the recommendations below:
Work only if you are in a good physical condition.
Work attentively, particularly as you finish.
Do not operate the machine when you are tired.
Carry out all work calmly, circumspectly and carefully.
Never operate the machine under the influence of alcohol, drugs or medica-
tion. This can impair your vision, reactions and your judgment.
Work in a manner that does not endanger others.
Ensure that no persons or animals are within the danger zone.
3.3 Protective gear
Work clothing
Clothing should be appropriate, i.e. should be close-fitting but not restrict your
movement.
When on construction sites, do not wear long hair loosely, loose clothing or jew-
elry including rings. These objects can easily get caught or be drawn in by mov-
ing machine parts.
Only wear clothing made of material that is not easily flammable.
Personal protective gear
Wear personal protective gear to avoid injuries or health hazards:
Non-skid, hard-toed shoes.
Work gloves made of durable material.
Overalls made of durable material.
Hard hat.
Ear protection.
Face protection.
Eye protection.
Breathing protection in the case of dusty ambient air.
Ear protection
This machine generates noise that exceeds the country-specific permissible
noise levels (individual rating level). It may therefore be necessary to wear ear
protection. You can find the exact value in the chapter Technical Data.
When wearing ear protection while working, you must pay attention and exercise
caution because your hearing is limited, e.g. in case someone screams or a sig-
nal tone sounds.
Wacker Neuson recommends that you always wear ear protection.
3Safety
14
100_0302_si_0001.fm
3.4 Transport
Switching off the machine
Before you transport the machine, it must be switched off, and the engine must
be given sufficient time to cool down.
Emptying the tank
Wacker Neuson recommends that the fuel tank be emptied and the carburetor
run dry prior to transporting it. Fuel could run out, e.g. if the machine is tilted.
Observe the national safety guidelines and the hazardous materials regulations
that apply to the respective means of transportation.
Transporting the machine
Secure the machine on the transport device against tilting, falling or slipping.
Lifting the machine
A falling machine can cause serious injuries.
The machine has no lifting or lashing points.
When lifting the machine, secure it in a closed transport container or similar in
order to prevent it from toppling, falling or slipping away.
Restarting
Machines, machine parts, accessories or tools that were detached for transport
purposes must be re-mounted and fastened before restarting.
Only operate in accordance with the operating instructions.
3 Safety
100_0302_si_0001.fm 15
3.5 Operating safety
Explosible environment
Never operate the machine in a potentially explosive environment.
Work environment
Familiarize yourself with your work environment before you start work. This in-
cludes e.g. the following items:
Obstacles in the work and traffic area.
Load-carrying capacity of the ground.
The measures needed to cordon off the construction site from public traffic in
particular.
The measures needed to secure walls and ceilings.
Options available in the event of an accident.
Safety in the work area
When working with the machine especially pay attention to the following points:
Electric lines or pipes in work area.
Gas lines or water lines in the work area.
Material becoming separated, dropping down or ejected. Make sure that you
do not put other persons in danger.
Pay maximum attention in the vicinity of drops or slopes. Risk of falling.
Maintain a sufficient distance from flammable materials.
Checks before starting work
Check the following points before beginning work:
Condition of tools.
Machine settings.
Starting the machine
Observe the safety information and warning notices located on the machine and
in the operator's manual.
Never attempt to start a machine that requires maintenance or repairs.
Start the machine as described in the operator's manual.
Vertical stability
Always make sure that you stand firmly when working with the machine. This ap-
plies particularly when working on scaffoldings, ladders, uneven or slippery
floors etc.
3Safety
16
100_0302_si_0001.fm
Caution with hot parts
Do not touch any hot parts such as tools, tool holders, mufflers or guide cylinders
during operation or for a short period afterwards. These parts can become very
hot and can cause severe burns.
Caution with movable parts
Keep your hands, feet and loose clothing away from moving or rotating machine
parts.
Caution with toxic materials
Some materials may contain toxic chemicals which are released during demoli-
tion. Therefore personal protective equipment must be worn to prevent inhalation
of and skin contact with work dust.
Do not direct towards people
Do not direct the machine towards people in the vicinity during operation. The
tool might be flung out and cause serious injuries.
No persons endangered
Be sure that no persons are endangered by flying or falling materials. Always
work very attentively, and anticipate potential hazards.
Switching off the machine
Switch off the engine in the following situations:
Before breaks.
If you are not using the machine.
Before storing the machine, wait until it has completely stopped running.
Store the machine or put it down in such a way that it cannot tilt, fall down or slip.
Storage
Set the machine down or store it securely so that it cannot tilt, fall down or slip.
Storage location
After operation, allow the machine to cool and then store it in a sealed-off, clean
and dry location protected against frost and inaccessible to children.
3 Safety
100_0302_si_0001.fm 17
3.6 Safety during the operation of hand machines
Safe working with hand machines
Secure loose workpieces with suitable methods.
While working, as a rule hold the machine on the provided handles with both
hands.
While working, hold the machine in such a way that hand injuries are avoided
when hitting hard objects.
Setting the hand machine down properly
Set the machine down carefully. Do not drop the machine to the floor or from
greater heights. Dropping the machine can cause injuries to other persons or the
machine itself can be damaged.
Safe working with the hammer
Keep the tool holder closed during operation.
3.7 Safety during the operation of combustion engines
Checking for signs of damage
Check the engine while switched off for leaks and cracks in the fuel line, tank and
fuel cap at least once per work shift.
Do not operate the machine if there is visible damage or defects.
Have any damage or defects eliminated immediately.
Dangers during operation
Combustion engines can be dangerous, particularly during operation and when
refueling.
Read and follow all safety instructions. Otherwise there is a risk of personal injury
and/or damage to property!
Do not start the engine near spilt fuel or if you smell fuel – this may cause an ex-
plosion!
Remove the machine from such areas.
Remove the spilt fuel immediately!
Not changing the engine speed
Do not change the preset engine speed, as this may cause engine damage.
3Safety
18
100_0302_si_0001.fm
Preventing fires
Open flames and smoking are strictly prohibited in the immediate vicinity of the
machine.
Make sure that waste, such as paper, dry leaves or grass do not accumulate
around the exhaust muffler. The waste materials may ignite.
Safety precautions when refueling
Please observe the following safety-relevant instructions when refueling:
Do not refuel near open flames.
Do not smoke.
Turn off the engine before refueling and allow it to cool down.
Refuel in a well-ventilated environment.
Wear fuel-proof protective gloves and, if there is the possibility of spraying,
protective goggles and clothing.
Do not inhale fuel vapors.
Avoid skin and eye contact with fuel.
For refueling, use clean tools such as a hopper.
Do not spill fuel, especially onto hot parts.
Remove any spilt fuel immediately.
Use the correct fuel grade.
Do not mix fuel with other liquids.
Fill the tank only up to the maximum marking. If there is no Maximum mark-
ing, do not fill up the tank completely.
Lock the fuel cap securely after refueling.
Operation in closed rooms
In closed or partially closed rooms such as tunnels, drifts or deep trenches, en-
sure sufficient ventilation by, for example, providing a powerful exhaust air fan.
Danger of poisoning! Do not inhale exhaust fumes. They contain toxic carbon
monoxide that can lead to unconsciousness or death.
Caution with hot parts
Do not touch any hot parts such as the engine block or exhaust muffler during
operation or directly afterwards. These parts can become very hot and cause se-
vere burns.
3 Safety
100_0302_si_0001.fm 19
Not using starter sprays
Highly flammable starter sprays pose a fire hazard.
Do not use any starter sprays.
Starter sprays are highly flammable and can cause backfiring and engine dam-
age.
Shutting off the fuel tap
When the machine stops, shut off the fuel tap.
Cleaning the engine
Clean the engine when it is cool to remove any dirt.
Do not use gasoline or solvents. Danger of explosion!
Health hazard due to exhaust fumes
Warning
The engine's exhaust fumes contain chemicals which are known to the State of
California to cause cancer, congenital defects or other reproductive anomalies.
Notes on the EPA engine
Caution
This machine is equipped with an EPA-certified engine.
Modifying the motor speed influences the EPA certification and emission. The
motor may only be set by a skilled technician.
For more detailed information, contact your nearest motor or Wacker Neuson
representative.
3.8 Maintenance
Maintenance work
Service and maintenance work must only be carried out to the extent described
in these operating instructions. All other procedures must be performed by your
Wacker Neuson representative.
For further information, refer to chapter Maintenance.
Switching off the engine
Before carrying out care or maintenance work, switch off the engine and allow it
to cool down.
For gasoline powered engines, you must pull off the spark plug cap.
3Safety
20
100_0302_si_0001.fm
Handling operating fluids safely
Observe the following points when handling operating fluids, e.g. fuels, oils,
greases, coolants etc.:
Always wear personal safety clothing.
Avoid skin and eye contact with operating fluids.
Do not inhale or swallow operating fluids.
In particular, avoid contact with hot operating fluids. Burn and scalding haz-
ard.
Dispose of replaced or spilled operating fluids according to the applicable
regulations for environmental protection.
If operating fluids escape from the machine, cease operation of the machine
and have it repaired immediately by your Wacker Neuson representative.
Cleaning
Always keep the machine clean and be sure to clean it each time you have fin-
ished using it.
Do not use gasoline or solvents. Danger of explosion!
Do not use high pressure washers. Permeating water can damage the machine.
When electrical equipment is present, this can pose a serious injury risk from
electric shocks.
Cleaning the zerk fitting
Wipe the zerk fitting with a clean cloth after the lubrication of the machine. There
is a danger of electrocution if there is excessive grease on the zerk fitting.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158

Wacker Neuson BH 65 28x152 US Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues