Poulan Pro HDF900 Manuel utilisateur

Catégorie
Mini motoculteurs
Taper
Manuel utilisateur
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
OPERATOR'S MANUAL
MODEL:
HDF900
FRONT TINE TILLER
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulanpro.com
WARNING:
Read this Man u al and follow all Warn-
ings and Safety Instructions. Fail ure
to do so can re sult in serious in ju ry.
IMPORTANT MANUAL Do Not Throw Away
01.30.15 BY Printed in U.S.A.
115 73 27-32
2
dangerous.
Never operate the tiller without proper guards, plates,
or other safety protective devices in place.
Keep children and pets away.
Do not overload the machine capacity by attempting
to till too deep at too fast a rate.
Never operate the machine at high speeds on slippery
surfaces. Look behind and use care when backing.
Never allow bystanders near the unit.
Use only attachments and accessories approved by
the manufacturer of the tiller.
Never operate the tiller without good visibility or light.
Be careful when tilling in hard ground. The tines may
catch in the ground and propel the tiller forward. If this
occurs, let go of the handlebars and do not restrain
the machine.
MAINTENANCE AND STORAGE
Keep machine, attachments, and accessories in safe
work ing condition.
Check shear pins, engine mounting bolts, and other
bolts at frequent intervals for proper tightness to be
sure the equip ment is in safe working condition.
Never store the machine with fuel in the fuel tank inside
a building where ignition sources are present, such
as hot water and space heaters, clothes dryers, and
the like. Allow the engine to cool before storing in any
enclosure.
Always refer to the operator’s guide instructions for
im por tant details if the tiller is to be stored for an ex-
tended period.
- IMPORTANT -
CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF
ATTRACTING ATTENTION TO IMPORTANT OR CRIT I CAL
IN FOR MA TION IN THIS MANUAL.
IMPORTANT: USED TO ALERT YOU THAT THERE IS A
POS SI BIL I TY OF DAM AG ING THIS EQUIP MENT.
NOTE: Gives essential information that will aid you to
better understand, incorporate, or execute a particular
set of instructions.
Look for this symbol to point out im-
por tant safety precautions. It means
CAUTION!!! BE COME ALERT!!! YOUR
SAFE TY IS INVOLVED.
CAUTION: Always disconnect spark
plug wire and place wire where it can-
not contact spark plug in order to pre-
vent ac ci den tal starting when setting
up, trans port ing, adjusting or making
re pairs.
TRAINING
Read this Manual care ful ly. Be thor ough ly fa mil iar with
the controls and the proper use of the equip ment.
Know how to stop the unit and disengage the controls
quickly.
Never allow children to operate the equipment. Never
allow adults to op er ate the equipment without proper
instruction.
Keep the area of operation clear of all persons, par-
tic u lar ly small children, and pets.
PREPARATION
Thoroughly inspect the area where the equipment is
to be used and remove all foreign objects.
Disengage all clutches and shift into neutral before
starting the engine (mo tor).
Do not operate the equipment with out wearing ad-
e quate outer gar ments. Wear footwear that will im prove
footing on slippery surfaces.
Handle fuel with care; it is highly flammable.
Use an approved fuel container.
Never add fuel to a running engine or hot engine.
Fill fuel tank outdoors with extreme care. Never fill fuel
tank indoors.
Replace gasoline cap securely and clean up spilled
fuel before restarting.
Use extension cords and receptacles as specified by
the manufacturer for all units with electric drive motors
or electric starting motors.
Never attempt to make any adjustments while the
engine (motor) is running (except where specifically
rec om mend ed by manufacturer).
OPERATION
Do not put hands or feet near or under rotating parts.
Exercise extreme caution when op er at ing on or cross-
ing gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic. Do not carry pas sen gers.
After striking a foreign object, stop the engine (motor),
remove the wire from the spark plug, thoroughly in spect
the tiller for any damage, and repair the damage before
restarting and op er at ing the tiller.
Exercise caution to avoid slipping or falling.
If the unit should start to vibrate ab nor mal ly, stop the
engine (motor) and check immediately for the cause.
Vi bra tion is generally a warning of trouble.
Stop the engine (motor) when leaving the operating
position.
Take all possible precautions when leav ing the ma chine
unattended. Disengage the tines, shift into neutral,
and stop the engine.
Before cleaning, repairing, or inspecting, shut off
the engine and make certain all moving parts have
stopped. Disconnect the spark plug wire, and keep the
wire away from the plug to prevent accidental starting.
Disconnect the cord on electric motors.
Do not run the engine indoors; exhaust fumes are
SAFETY RULES
Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers
3
PRODUCT SPECIFICATIONS
CONGRATULATIONS on your purchase of a new tiller. It
has been designed, en gi neered and manu fac tured to give
you the best pos sible de penda bil ity and per form ance.
Should you experience any prob lems you can not easily
remedy, please contact your nearest authorized service
center. We have com pe tent, well-trained tech ni cians and
the proper tools to service or repair this unit.
Please read and retain this manual. The in struc tions will
enable you to assemble and main tain your tiller prop erly.
Always observe the “SAFETY RULES”.
CUSTOMER RESPONSIBILITIES
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your tiller.
Follow instructions under “Maintenance” and “Stor age”
sections of this Manual.
IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL
COMBUSTION ENGINE AND SHOULD NOT BE USED ON
OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-
COVERED OR GRASS COVERED LAND UNLESS THE ENGINE'S
EXHAUST SYSTEM IS EQUIPPED WITH A SPARK ARRESTER
MEETING APPLICABLE LOCAL LAWS (IF ANY). IF A SPARK
ARRESTER IS USED, IT SHOULD BE MAINTAINED IN EFFECTIVE
WORK ING ORDER BY THE OPERATOR.
IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS
REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA
PUBLIC RESOURCES CODE). OTHER STATES MAY HAVE
SIMILAR LAWS. FEDERAL LAWS APPLY ON FEDERAL LANDS.
SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT
FOR SPARK ARRESTER.
GASOLINE CAPACITY: 3 Quarts (2.8L)
Unleaded Regular
OIL (API:SG-SL): SAE 30 (Above 32°F )
(Capacity: 16 oz./0.45L) SAE 5W-30 (Below 32°F)
SPARK PLUG : NGK-BPR6ES
(GAP: .030"/0.76mm) TORCH-F6RTC
MAINTENANCE SCHEDULE ..................................... 10
MAINTENANCE ................................................... 10-12
SERVICE & ADJUSTMENTS ................................ 13-15
STORAGE .................................................................. 15
TROUBLESHOOTING ................................................ 16
WARRANTY ........................................................... 17-18
SAFETY RULES ........................................................... 2
PRODUCT SPECIFICATIONS ..................................... 3
CUSTOMER RESPONSIBILITIES ............................... 3
ASSEMBLY ................................................................4-5
OPERATION .............................................................. 6-9
TABLE OF CONTENTS
4
ASSEMBLY
OPERATOR’S POSITION (See Fig. 1)
When right or left hand is mentioned in this manual, it
means when you are in the operating position (standing
behind tiller handles).
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) Utility knife
(1) Screwdriver
(1) Pair of pliers
(2) 1/2" wrenches
Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
OPERATOR'S POSITION
RIGHT
FRONT
LEFT
overhead_views_8
Fig. 1
(4) Washers 3/8 x 7/8 x 14
(6) Lock Washers 5/16 (6) Hex Nuts 5/16-18(6) Hex Bolts 5/16-18 x 1-1/4
(1) Manual
CONTENTS OF HARDWARE PACK
5
ASSEMBLY
INSTALL DEPTH STAKE ASSEMBLY
(See Fig. 3)
Loosen nut “A”.
Insert stake support between engine bracket halves
with stake spring down.
Bolt stake support to engine brackets with bolts, lock
washers and nuts. Tighten se curely. Tighten nut “A”.
Depth stake must move freely. If it does not, loosen
support bolt.
HANDLE HEIGHT
Handle height may be adjusted to better suit operator.
(See “HANDLE HEIGHT” in the Service and Ad just-
ments section of this manual).
TILLING WIDTH
Tilling width may be adjusted to better handle your
tilling con di tions (See “TINE ARRANGEMENT” in the
Ser vice and Adjustments section of this manual).
TINE OPERATION
Check tine operation before first use. (See “TINE
OPERATION CHECK” in the Service and Adjustments
section of this manual).
UNPACK CARTON & INSTALL HANDLE (See
Fig. 2)
CAUTION: Be careful of exposed sta ples
when handling or disposing of carton-
ing material.
IMPORTANT: WHEN UNPACKING AND AS SEM BLING TILLER,
BE CAREFUL NOT TO STRETCH OR KINK CABLE(S).
Cut cable ties securing handles.
The handle may be assembled in high or low posi-
tion. Slowly lift handle as sem bly up, route cable(s)
as shown and align han dle holes with desired handle
panel hole and slot.
Loosely assemble hardware as shown. Repeat for
opposite side. Tight en all hard ware se cure ly.
NOTE: Cables must not touch the muffler.
Cut cable ties securing tiller to skid and remove tiller
from skid.
Remove screws securing depth stake to skid and
discard the screws.
depth_stake_4
DEPTH
STAKE
HEX BOLTS,
LOCK WASH ERS, AND HEX NUTS
DEPTH STAKE
SUPPORT
NUT “A
ENGINE BRACK ET HALVES
STAKE SPRING
Fig. 3
SUPPORT
BOLT
TILLER
HANDLE
CABLE
HANDLE
PANEL
BOLTS
Fig. 2
HAN DLE PANEL TILLER
HANDLE
HEX BOLTS
5/16-18 x
1-1/4"
FLAT
WASHERS
LOCK
WASH ER
NUT
6
KNOW YOUR TILLER
READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.
Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning.
Fig. 4
MEETS ANSI SAFETY REQUIREMENTS
Our tillers conform to the safety standards of the American National Standards Institute.
OPERATION
RECOIL
STARTER
HANDLE
DEPTH STAKE
TINE
SHIELD
ENGINE ON/
OFF SWITCH
CHOKE CONTROL
FORWARD TINE
CONTROL
TINES
THROTTLE
CONTROL
FUEL VALVE
CHOKE CONTROL - Used when starting a cold engine.
DEPTH STAKE - Controls forward speed and the depth
at which the tiller will dig.
ENGINE ON/OFF SWITCH - The engine switch enables
and disables the ignition system.
FORWARD TINE CONTROL - Engages tines in forward
direction.
FUEL VALVE - The fuel valve opens and closes the pas-
sage between the fuel tank and the carburetor.
RECOIL STARTER HANDLE - Used to start the engine.
direction.
THROTTLE CONTROL - Controls engine speed.
7
OPERATION
TILLING
The speed and depth of tilling is regulated by the position
of the depth stake and wheel height.
The depth stake should always be below the wheels for
digging. It serves as a brake to slow the tiller’s forward
motion to enable the tines to penetrate the ground. Also,
the more the depth stake is lowered into the ground the
deeper the tines will dig.
DEPTH STAKE (See Fig. 6)
Adjust depth stake by removing the hairpin clip and clevis
pin. Change depth stake to desired position. Replace the
clevis pin and hairpin clip.
For normal tilling, set depth stake at the second or
third hole from the top.
WHEELS (See Fig. 6)
Adjust wheels by removing the hairpin clip and clevis pin.
Change wheel position. Replace the hairpin clip and
clevis pin.
For normal tilling, set wheels at the second or third
hole from the top.
TINE OPERATION (See Fig. 5)
Squeeze tine control to handle.
HOW TO USE YOUR TILLER
Know how to operate all controls before adding fuel and
oil or attempting to start engine.
STOPPING (See Fig. 5)
TINES
1. Release tine control to stop move ment.
ENGINE
2. Move throttle control to “SLOW” po si tion and allow
the engine to run slowly for cool down.
3. Turn the engine switch to the "OFF" Position.
4. Turn the fuel valve lever to the "OFF" Position.
NOTE: NEVER USE CHOKE TO STOP ENGINE.
IMPORTANT: TO STOP ENGINE IN AN EMERGENCY, TURN
THE ENGINE SWITCH TO THE OFF POSITION.
Fig. 5
THROTTLE
CONTROL
ENGINE SWITCH
FUEL VALVE
THROTTLE
CONTROL ENGINE
SWITCH FUEL
VALVE
HANDLES?
TINE CONTROL
“OFF” (UP)
POSITION
TINE CONTROL
“ON” (DOWN)
POSITION
1
depth_stake_4
WHEELS
HAIRPIN CLIP
AND CLEVIS PIN
HAIRPIN CLIP
AND CLEVIS PIN
DEPTH
STAKE
STAKE
SPRING
Fig. 6
The operation of any tiller can result in foreign objects thrown into the
eyes, which can result in severe eye damage. Always wear safety glasses
or eye shields before starting your tiller and while tilling. We recommend
a wide vision safety mask over spectacles or standard safety glasses.
Use ear protec-
tors to avoid
damage to
hearing.
8
OPERATION
ADD GASOLINE
Fill to within 1/2" of top of fuel tank to prevent spills and
to allow for fuel expansion. Do not overfill. Use fresh,
clean, regular un lead ed gasoline with a minimum of
87 octane. Do not mix oil with gasoline. Purchase
fuel in quan ti ties that can be used within 30 days to
assure fuel freshness.
CAUTION: Fill to within 1/2" of top of
fuel tank to prevent spills and to allow
for fuel expansion. If gasoline is ac-
ci den tal ly spilled, move machine away
from area of spill. Avoid creating any
source of ignition until gasoline vapors
have disappeared.
Wipe off any spilled oil or fuel. Do not
store, spill or use gasoline near an
open flame.
IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW
32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO
HELP INSURE GOOD COLD WEATHER START ING.
CAUTION: Alcohol blended fuels (called gas o-
hol or using ethanol or methanol) can attract
moisture which leads to sep a ra tion and for ma-
tion of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied before stor age of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next sea-
son. See Storage In struc tions for additional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
TO TRANSPORT
CAUTION: Before lifting or trans port-
ing, allow tiller engine and muffler to
cool. Disconnect spark plug wire. Drain
gasoline from fuel tank.
AROUND THE YARD
Tip depth stake forward until it is held by the stake
spring.
Push tiller handles down, raising tines off the ground.
Push or pull tiller to desired location.
AROUND TOWN
Disconnect spark plug wire.
Drain fuel tank.
Transport in upright position to prevent oil leakage.
BEFORE STARTING ENGINE
IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO
ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR
FUEL. USE CLEAN OIL AND FUEL AND STORE IN AP PROVED,
CLEAN, COVERED CON TAIN ERS. USE CLEAN FILL FUNNELS.
FILL ENGINE WITH OIL (See Fig. 7)
1. Remove hangtag from engine.
2. With engine level, remove engine oil fill er plug.
3. Fill engine with oil to point of over flow ing. For ap proxi-
mate ca pac i ty see “PROD UCT SPEC I FI CA TIONS” on
page 3 of this manual. All oil must meet A.P.I. Service
Classification SG-SL.
4. Tilt tiller back on its wheels and then re-level.
5. With engine level, refill to point of over flow ing if nec-
es sary. Re place oil filler plug.
For cold weather operation you should change oil for
easier starting (See “OIL VISCOSITY CHART” in the
Main te nance section of this man u al).
To change engine oil, see the Main te nance section of
this manual.
engine_art_4
Oil Level Oil Filler Plug
Max Upper Level
Min Lower Level
Fig. 7
TO START ENGINE (See Fig. 8)
CAUTION: KEEP TINE CONTROL IN “OFF”
PO SI TION WHEN STARTING ENGINE.
When starting engine for the first time or if engine has run
out of fuel, it will take ex tra pulls of the recoil starter to
move fuel from the tank to the engine.
1. Make sure spark plug wire is prop er ly connected.
2. Place the fuel valve to the "ON" position.
3. To start a cold engine, move the choke lever to the
"ON" position.
4. Move the throttle lever away from the "SLOW" position,
about 1/3 of the way toward the "FAST" position.
5. Turn the engine switch to the "ON" position. Pull rope
out slowly until engine reaches start of com pres sion
cy cle (rope will pull slightly harder at this point).
6. Pull recoil starter handle quickly. Do not let starter
handle snap back against starter. Repeat if necessary.
NOTE: IF ENGINE FIRES BUT DOES NOT START, MOVE CHOKE
CONTROL TO HALF CHOKE POSITION. PULL RECOIL STARTER
HANDLE UNTIL ENGINE STARTS.
9
OPERATION
BREAKING IN YOUR TILLER
Break-in your belt(s), pulleys and tine control before you
actually begin tilling.
Start engine, tip tines off ground by pressing handles
down and engage tine control to start tine rotation.
Allow tines to rotate for five minutes.
Check tine operation and adjust if necessary. See “TINE
OPERATION CHECK” in the Service and Ad just ments
sec tion of this manual.
TILLING HINTS
CAUTION: Until you are accustomed
to handling your tiller, start ac tu al field
use with throttle in slow position.
To help tiller move forward, lift up the handles slightly (thus
lifting depth stake out of ground). To slow down the tiller,
press down on handles.
If you are straining or tiller is shaking, the wheels and depth
stake are not set properly in the soil being tilled. The proper
setting of the wheels and depth stake is through trial and
error and depends upon the soil con di tion. (The harder or
wetter the ground, the slower the engine and tine speed
needed. Under these poor con di tions, at fast speed the
tiller will run and jump over the ground).
A properly adjusted tiller will dig with little effort from the
operator.
Tilling is digging into, turning over, and breaking up
packed soil before planting. Loose, unpacked soil
helps root growth. Best tilling depth is 4"-6". A tiller
will also clear the soil of unwanted vege ta tion. The
de com po si tion of this vegetable mat ter en rich es the
soil. De pend ing on the climate (rain fall and wind), it
may be advisable to till the soil at the end of the grow-
ing season to further condition the soil.
Soil conditions are important for proper tilling. Tines will
not readily penetrate dry, hard soil which may con trib ute
to excessive bounce and difficult handling of your tiller.
Hard soil should be mois tened before tilling; however,
extremely wet soil will “ball-up” or clump during tilling.
Wait until the soil is less wet in order to achieve the
best results. When tilling in the fall, remove vines and
long grass to prevent them from wrapping around the
tine shaft and slowing your tilling operation.
You will find tilling much easier if you leave a row un-
tilled between passes. Then go back between tilled
rows. (See Fig. 9) There are two reasons for doing
this. First, wide turns are much easier to negotiate
than about-faces. Sec ond, the tiller won’t be pulling
itself, and you, toward the row next to it.
Set depth stake and wheel height for shallow tilling
when working extremely hard soil or sod. Then work
across the first cuts at normal depth.
NOTE: IF ENGINE DOES NOT START, SEE TROU BLE SHOOT ING
POINTS.
7. If the choke lever has been moved to the "ON" position
to start the engine, gradually move it to the opposite
position as the engine warms up.
NOTE: A WARM ENGINE REQUIRES LESS CHOK ING TO
START.
8. Move throttle control to desired running position.
9. Allow engine to warm up for a few min utes before
engaging tines.
Fig. 8
THROTTLE CONTROL ENGINE
SWITCH
CHOKE
CON TROL
FUEL
VALVE
RECOIL
STARTER
HANDLE
SPARK
PLUG
Fig. 9
321
5
4
67
CULTIVATING
Cultivating is destroying the weeds between rows to pre-
vent them from robbing nourishment and moisture from
the plants. At the same time, breaking up the upper layer
of soil crust will help retain moisture in the soil. Best dig-
ging depth is 1"-3".
You will probably not need to use the depth stake.
Begin by tipping the depth stake forward until it is held
by the stake spring.
Cultivate up and down the rows at a speed which will
allow tines to uproot weeds and leave the ground in
rough con di tion, promoting no fur ther growth of weeds
and grass (See Fig. 10).
Fig. 10
10
MAINTENANCE
SAE 30 OR 10W-30 MOTOR OIL
REFER TO MAINTENANCE “ENGINE” SECTION
LUBRICATION CHART
GENERAL RECOMMENDATIONS
The warranty on this tiller does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, the operator must main tain
tiller as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tiller.
At least once a season, check to see if you should make
any of the adjustments described in the Service and Ad-
justments section of this manual.
Once a year you should replace the spark plug, clean
or replace air filter, and check tines and belts for wear.
A new spark plug and clean air filter assure proper
air-fuel mixture and help your engine run better and
last longer.
BEFORE EACH USE
Check engine oil level.
Check tine operation.
Check for loose fasteners.
LUBRICATION
Keep unit well lubricated (See “LUBRICATION CHART”).
MAINTENANCE
SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
Check Engine Oil Level
Change Engine Oil
Oil Pivot Points
Inspect Air Screen
Inspect Spark Arrester / Muffler
Clean or Replace Air Cleaner Cartridge
Clean Engine Cylinder Fins
Replace Spark Plug
BEFORE EACH USE
EVERY 25 HOURS
EVERY 5 HOURS
EVERY 50 HOURS
SERVICE DATES
2
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
EN GINE
TINE CON TROL
IDLER
ARM
11
MAINTENANCE
Fig. 11
Disconnect spark plug wire before performing any maintenance to prevent accidental start ing of
engine.
Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank
before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.
Do not touch hot muffler or cylinder fins as contact may cause burns.
TO CHANGE ENGINE OIL (See Figs. 11 and 12)
Determine temperature range expected before oil change.
All oil must meet API service classification SG-SL.
Be sure tiller is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
Remove drain plug.
Tip tiller forward to drain oil.
After oil has drained completely, replace oil drain plug
and tighten securely.
Remove oil filler plug. Be careful not to allow dirt to
enter the engine.
Refill engine with oil. See “CHECK ENGINE OIL LEVEL
in the Operation section of this manual.
AIR CLEANER (See Fig. 13)
Service air cleaner cartridge every twenty-five hours, more
often if engine is used in very dusty conditions.
Loosen air cleaner screws, one on each side of cover.
Remove air cleaner cover.
Carefully remove air cleaner cartridge. Be care ful. Do
not allow dirt or de bris to fall into carburetor.
Clean by tapping gently on a flat surface.
If very dirty or damaged, replace cartridge.
Clean and re place cover. Tighten screws securely.
CAUTION: Petroleum sol vents, such as
kerosene, are not to be used to clean
cartridge. They may cause de te ri o ra tion
of the cartridge. Do not oil car tridge.
Do not use pres sur ized air to clean or
dry cartridge.
4%-0%2!452%ª2!.'%ª!.4)#)0!4%$ª"%&/2%ª.%84ª/),ª#(!.'%
ªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªªª3!%ª6)3#/3)49ª'2!$%3
ENGINE
LUBRICATION
Use only high quality detergent oil rated with API service
classification SF-SJ. Select the oil’s SAE vis cos i ty grade
according to your expected temperature.
NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F (0°C). Check your
engine oil level more frequently to avoid possible engine
damage from running low on oil.
Change the oil after every 50 hours of operation or at least
once a year if the tiller is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Add SAE
30 motor oil or equivalent. Tighten oil filler plug securely
each time you check the oil level.
Fig. 12
OIL
FILLER
PLUG
OIL
DRAIN
PLUG OIL LEVEL
Fig. 13
PRE-CLEANER
COVER
AIR CLEANER
CARTRIDGE
AIR CLEANER SCREWS
12
MAINTENANCE
MUFFLER
Do not operate tiller without muffler. Do not tamper with
exhaust system. Damaged mufflers or spark arresters could
create a fire hazard. Inspect pe ri odi cally and re place if
nec es sary. If your engine is equipped with a spark arrester
screen assembly, re move every 50 hours for cleaning and
inspection. Re place if dam aged.
SPARK PLUG
Replace spark plugs at the beginning of each tilling sea-
son or after every 25 hours of use, whichever comes first.
Spark plug type and gap setting are shown in “PROD UCT
SPEC I FI CA TIONS” on page 3 of this manual.
TRANSMISSION
Your transmission is sealed and will not re quire lubrication
unless serviced.
CLEANING
Do not clean your tiller when the engine and transmission
are hot. We do not rec om mend using pressurized water
(gar den hose, etc.) to clean your unit un less the gasket
area around the trans mis sion and the engine muf fler, air
fil ter and car bu re tor are cov ered to keep wa ter out. Wa ter
in en gine will short en the useful life of your tiller.
Clean engine, wheels, finish, etc. of all foreign matter.
Keep finished surfaces and wheels free of all gas o line,
oil, etc.
Protect painted surfaces with au to mo tive type wax.
COOLING SYSTEM (See Fig. 14)
Your engine is air cooled. For proper en gine performance
and long life keep your engine clean.
Clean air screen frequently using a stiff-bristled brush.
Remove blower housing and clean as nec es sary.
Keep cylinder fins free of dirt and chaff.
BLOWER
HOUSING
AIR SCREEN
CYLINDER
FINS
MUFFLER
Fig. 14
13
CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into
contact with plug.
SERVICE AND ADJUSTMENTS
TILLER
TO ADJUST HANDLE HEIGHT (See Fig. 15)
Factory assembly has provided lowest handle height.
Se lect handle height best suited for your tilling conditions.
Handle height will be different when tiller digs into soil.
If a higher handle height is desired, loosen the four
nuts securing handle panel to engine brackets.
Slide handle panel to desired location.
Tighten the four nuts securely.
MID-WIDTH TILLING - 24" PATH (See Fig. 17)
Assemble holes “A” in tine hubs to holes “C” in tine
shaft.
NARROW TILLING/CULTIVATING - 12-3/4" PATH
(See Fig. 18)
Remove outer tines.
TINE ARRANGEMENT
Your outer tines can be assembled in several different ways
to suit your tilling or cultivating needs.
CAUTION: Tines are sharp. Wear gloves
or other protection when handling tines.
NORMAL TILLING - 26" PATH (See Fig. 16)
Assemble holes “A” in tine hubs to holes “B” in tine
shaft.
NOTE: When reassembling outer tines, be sure right tine
assembly (marked “R”) and left tine assembly (marked
“L”) are mounted to correct side of tine shaft.
TINE OPERATION CHECK (See Fig. 19)
WARNING: Disconnect spark plug wire
from spark plug to prevent starting while
checking tine operation.
For proper tine operation, forward tine control lever must be
against control body and all slack removed from inner wire
of control cable when control is in the “OFF” (up) position.
If lever and cable are loose, loosen cable clip at lower
end of cable. Pull up on cable to remove slack, without
extending spring on end of cable, and retighten cable clip.
FINAL CHECK “OFF” POSITION
With tine control “OFF” (up), push down on handle to
raise tines off the ground.
Slowly pull recoil starter handle while observing tines.
Tines should not rotate.
If tines rotate, inner wire of control cable is too tight
which is extending lower spring and engaging tines.
Loosen cable clip and push down on cable only enough
to relieve spring tension. Tighten cable clip.
HANDLE
PANEL
ENGINE BRACKETS
NUTS
(ALSO 2 ON
LEFT SIDE
OF TILLER)
Fig. 15
Fig. 18
tine_6
INNER TINES ONLY
tine_5
“A”“C“A” “C
Fig. 17
tine_4
OUTER TINE
HAIRPIN CLIP
“A”
“B”
“A”
“B”
Fig. 16
INNER TINE
CLEVIS PIN
14
SERVICE AND ADJUSTMENTS
Recheck in “OFF” position and adjust if necessary.
FINAL CHECK “ON” POSITION
With tine control “ON” (held down to handle) push
down on handle to raise tines off the ground.
Slowly pull recoil starter handle while observing tines.
Tines should rotate forward.
If tines do not rotate, inner wire of control cable is too
loose. Loosen cable clip and pull cable up to remove
slack and retighten clip.
Recheck in “ON” position and adjust if necessary.
NOTE: If “ON” position check required adjustment, re-
check “OFF” position adjustment to insure tines do not
rotate when control is “OFF” (up).
TO REPLACE V-BELT (See Fig. 21)
Replace V-belt if it has stretched considerably or if it has
cracks or frayed edges.
Belt guard must be removed to service belt. See “TO
REMOVE BELT GUARD” in this section of manual.
BELT REMOVAL
Remove V-belt from transmission pulley first and then
from engine pulley.
BELT REPLACEMENT
Install new V-belt to engine pulley first then to trans-
mis sion pulley. Be sure belt is positioned on inside
groove of both pulleys, inside all belt guides and rests
on idler pulley.
CHECK TINE OPERATION
See “TINE OPERATION CHECK” in this section of
manual.
REPLACE BELT GUARD
CABLE CLIP
TINE CON TROL CABLE
Fig. 19
FORWARD TINE
CONTROL
“ON” (DOWN)
POSITION
FORWARD
TINE CONTROL
“OFF” (UP)
POSITION
SCREW
BELT GUARD
SCREW
SCREW
Fig. 20
TO REMOVE BELT GUARD (See Fig. 20)
Remove screws from side of belt guard.
Pull belt guard out and away from unit.
Replace belt guard by reversing above procedure. Be
sure slot in bottom of belt guard is under head of tine
shield bolt and all nuts are tightened securely.
Fig. 21
V-BELT
ENGINE
PULLEY BELT GUIDE
TRANS MIS SION PUL LEY
IDLER
PUL LEY
BELT
GUIDE
15
SERVICE AND ADJUSTMENTS
STORAGE
Immediately prepare your tiller for storage at the end of the
season or if the unit will not be used for 30 days or more.
WARNING: Never store the tiller with
gasoline in the tank inside a build ing
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.
TILLER
Clean entire tiller (See “CLEANING” in the Maintenance
section of this manual).
Inspect and replace belts, if nec es sary (See belt re-
place ment in struc tions in the Service and Ad just ments
section of this manual).
Lubricate as shown in the Maintenance section of this
manual.
Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, break age
and wear. Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH
AS THE CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING
ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH
LEADS TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF
AN ENGINE WHILE IN STORAGE.
Drain the fuel tank.
Start the engine and let it run until the fuel lines and
car bu re tor are empty.
Never use engine or carburetor cleaner products in
the fuel tank or permanent damage may occur.
NOTE: Fuel stablizer is an acceptable alternative inmini-
mizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stablizer container.
Run engine at least 10 minutes after adding stablizer to
allow the stabilizer to reach the carburetor. Do not drain
the gas tank and carburetor if using fuel stabilizer.
ENGINE
Maintenance, repair, or replacement of the emission control
devices and systems, which are being done at the cus tom-
ers expense, may be performed by any non-road engine
repair establishment or individual. Warranty repairs must
be performed by an authorized engine manufacturer's
service outlet.
IMPORTANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE
SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY
HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK
THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/
DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND
EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.
ENGINE OIL
Drain oil (with engine warm) and replace with clean oil.
(See “ENGINE” in the Maintenance section of this man ual).
CYLINDER(S)
Remove spark plug.
Pour 1 ounce (29 ml) of oil through spark plug hole
into cylinder.
Pull starter handle slowly several times to distribute
oil.
Replace with new spark plug.
OTHER
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
If possible, store your unit indoors and cover it to give
protection from dust and dirt.
Cover your unit with a suitable pro tec tive cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows con den sa tion to form
and will cause your unit to rust.
IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND
EXHAUST AREAS ARE STILL WARM.
16
TROUBLESHOOTING POINTS
Will not start 1 Out of fuel. 1 Fill fuel tank.
2 Fuel valve “OFF” 2 Turn fuel valve to the “ON” position.
3 Engine Switch “OFF” 3 Turn engine switch to the “ON” position.
4 Engine not “CHOKED” properly. 4 See “TO START ENGINE” in Operation section.
5 Engine flooded. 5 Wait several minutes before attempting to start.
6 Bad spark plug or improper gap. 6 Replace spark plug or adjust gap.
7 Dirty air filter. 7 Clean/replace air filter.
8 Water in fuel. 8 Empty fuel tank and carburetor, refill tank with fresh gasoline.
Hard to start 1 Throttle control not set properly. 1 See “To Start Engine” in Operations section.
2 Dirty air filter. 2 Clean/replace air filter.
3 Bad spark plug or improper gap. 3 Replace spark plug or adjust gap.
4 Stale or dirty fuel. 4 Empty fuel tank and refill tank with fresh, clean gasoline.
5 Loose spark plug wire. 5 Make sure spark plug wire is seated properly.
Loss of power 1 Engine is overloaded 1 Set depth stake and wheels for shallower tilling.
2 Dirty air cleaner 2 Clean/replace air filter.
3 Low oil level/dirty oil. 3 Check oil level/change oil.
4 Faulty spark plug. 4 Clean and regap or change spark plug.
5 Oil in fuel 5 Empty and clean fuel tank and refill, and clean carburetor.
6 Stale or dirty fuel. 6 Empty fuel tank and refill tank with fresh, clean gasoline.
7 Water in fuel. 7 Empty fuel tank and carburetor, refill tank with fresh gasoline.
8 Clogged fuel tank. 8 Remove fuel tank and clean.
9 Spark plug wire loose. 9 Connect and tighten spark plug wire.
10 Dirty engine air screen. 10 Clean engine air screen.
11 Dirty/clogged muffler. 11 Clean/replace muffler.
12 Poor Compression 12 Contact a qualified service center.
Engine overheats 1 Low oil level/dirty oil. 1 Check oil level/change oil.
2 Dirty engine air screen. 2 Clean engine air screen.
3 Dirty engine. 3 Clean cylinder fins, airscreen, muffler area
4 Partially plugged muffler 4 Remove and clean muffler.
Excessive bounce/
difficult handling
1 Ground too dry and hard. 1 Moisten ground or wait for more favorable soil conditions
2 Wheels and depth stake incorrectly adjusted. 2 Adjust wheels and depth stake.
Soil balls up or clumps 1 Ground too wet. 1 Wait for more favorable conditions.
Engine runs but tiller
won’t move
1 Tine control is not engaged. 1 Engage tine control
2 V-belt not correctly adjusted. 2 Inspect/adjust V-belt.
3 V-belt is off pulley (s). 3 Inspect V-belt.
Engine runs but labors
when tilling
1 Tilling too deep. 1 Set depth stake for shallower tilling
2 Throttle control not properly adjusted. 2 Check throttle control setting.
17
LIMITED WARRANTY
What is covered. We warrant that this product is free from defects in material or workmanship under normal use
and maintenance. Certain components, such as normal wear parts, engines, and transmissions are excluded from this
warranty. We will, at our option, repair or replace any defective product or part covered by the Limited Warranty, free of
charge at any authorized Servicing Dealer/Center using OEM replacement parts, subject to the limitations and exclusions
described below.
Limited Warranty period. We will warrant the product to the original retail purchaser from the date of retail purchase for
the applicable period of time shown on the chart below.
What is NOT covered. This Limited Warranty does not cover:
(a) Engines and transmissions, except as noted on the chart below; a separate warranty provided with your product
might apply.
(b) Normal wear parts (parts and items that normally wear out with use), including without limitation spark plugs, bulbs,
filters, lubricants, starter cords, belts, blades, and blade adapters are not covered, nor is damage due to normal wear,
such as abrasion to mower decks, tires punctured by an external source, natural discoloration of materials, or dulling
or damage to blades due to contact with abrasives, rocks, rods, or other foreign objects.
(c) Emissions control equipment and components to the extent regulated by the U.S. Environmental Protection Agency
or similar government agencies. These are covered by a separate emission control warranty contained in the opera-
tor’s manual.
(d) Depending on the product, there is either NO WARRANTY or a reduced warranty if the product is used for commer-
cial, non-residential, or rental purposes and, in such circumstances, this Limited Warranty is offered instead of and
replaces any warranty regime provided by law. Please refer to the chart below.
(e) Damage related to abuse, misuse, neglect, modifications, alterations, use of unauthorized attachments, improper
storage, or lack of lubrication or engine failure due to the use of oils that do not meet engine manufacturer's specifi-
cations, pressure cleaning or steam cleaning the product, excessive dirt, abrasives, salt water, moisture, corrosion,
rust, or varnish. Failure to perform required maintenance as described in the operator’s manual will void this war-
ranty.
(f) Damage or failures due to improper set up, pre-delivery service or repair service by anyone other than an authorized
servicing dealer during the warranty period.
(g) Damage caused by use of gasoline containing more than 10% (E10) ethanol content (e.g. E15, E25, E30, E50, E85),
use of ether or similar starting fluids, or stale fuel.
(h) Damage to sprayers from using caustic or flammable materials in the sprayer, or lack of or broken strainers.
Your Responsibilities. To preserve your rights under this Limited Warranty, you must exercise reasonable care and use
of the product, including following the preventive maintenance, storage, and fuel and oil usages as prescribed in the
operator's manual. Any adjustment (e.g. to the throttle cable or belt guides) after the first thirty days of purchase and
any preventive maintenance as outlined in the operator's manual are NOT covered. In addition, you must cease using
the product immediately upon any failure or damage, and take the product to an authorized servicing dealer prior to any
further use.
WARRANTY EXCLUSIONS, DISCLAIMERS, AND LIMITED RIGHTS. WE WILL NOT BE LIABLE FOR ANY INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES. YOUR REMEDY IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT
OR PART, AT OUR DISCRETION. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SET FORTH HEREIN.
ANY WARRANTY IMPLIED BY STATE LAW (WHETHER OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE
OR OTHERWISE) IS HEREBY DISCLAIMED; WHERE SUCH A DISCLAIMER IS NOT PERMITTED BY LAW, THEN SUCH
IMPLIED WARRANTY IS LIMITED FOR THE DURATION OF THE APPLICABLE LIMITED WARRANTY PERIOD LISTED IN
THE CHART BELOW. SOME LOCALITIES, INCLUDING THE PROVINCE OF QUEBEC, DO NOT ALLOW EXCLUSIONS
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS,
SO THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS BASED
ON YOUR LOCALITY.
How to obtain service. To obtain warranty service, you must take your product to an authorized Servicing Dealer/Cen-
ter. To find your nearest authorized Servicing Dealer/Center, visit our website and use the Dealer Locator feature, or call
1-800-487-5951 from 8:00 AM to 7:00 PM EST. Any costs to transport or ship the product are your responsibility. You
must present proof of purchase (including date, product model and serial number) to an authorized Servicing Dealer/
Center for warranty service. Proof of purchase rests solely with you. You may register your product using our online
product registration site to help ensure that you are notified of important product information. However, registering your
product is not a condition of warranty service.
587 70 47-01 Rev. A 2014-09-30
2015
www.poulan.com www.poulanpro.com www.weedeater.com www.mcculloch.com
18
1 Your engine is warranted separately by the engine manufacturer;
please refer to the separate engine warranty provided with your product.
2 Battery warranty does not include discharged or uncharged batteries.
3 Hydro-Gear warrants transmission for two (2) years consumer warranty, parts and labor.
Snow Throwers and Lawn Tractors:
Hydro-Gear warrants transmission for two (2) years consumer warranty, parts and labor.
For all others, your transmission is warranted separately by the transmission manufacturer;
please refer to the separate transmission warranty provided with your product.
4 Replacement parts and accessories provided under this Limited Warranty are warranted only for the BALANCE of the
warranty period applicable to the part or accessory that was replaced.
Product Registration
Please register your product at corresponding website:
www.poulan.com; www.poulanpro.com; www.weedeater.com; or www.mcculloch.com
Go to “Customer Support” then “Product Registration”
You may call 1-800-487-5951 (US) or 1-800-805-5523 (Canada) to have your product registered.
Please have all product information ready prior to calling Consumer Support.
Consumer
(personal,
household
use only)
Commercial
(any commercial,
professional, agri-
cultural, institutional
or income producing
use, other than
rental use)
Rental
(any
rental
usage)
2 Years No Warranty No Warranty
1 Year No Warranty No Warranty
2 Years No Warranty No Warranty
1 Year No Warranty No Warranty
2 Years No Warranty No Warranty
2 Years No Warranty No Warranty
2 Year No Warranty No Warranty
2 Years No Warranty No Warranty
180 days 180 days 180 days
Rato, LCT, Locin 2 years 90 days No Warranty
All Others See Note 1 See Note 1 See Note 1
Tuff Torq, General Transmission 2 Years No Warranty No Warranty
Peerless 3 Years No Warranty No Warranty
Hydro-Gear See note 3 See note 3 See note 3
All Others See note 3 See note 3 See note 3
Zero-Turn Mowers and Riding Tractors with steel reinforced 10 Years No Warranty No Warranty
Zero-Turn Mowers and Riding Tractors fabricated deck shell See Note 1 No Warranty No Warranty
Collection Systems and Baggers 1 Year 90 days No Warranty
All other accessories (e.g., bars, chains, carrying cases, trimmer 90 days 30 days No Warranty
Parts (e.g., belts, blades, starter covers, starter springs, etc.) 30 days 30 days No Warranty
30 days No Warranty No Warranty
Poulan, Poulan Pro, Weedeater, & McCulloch®
Warranty Chart 2015
All Wheeled Lawn and Garden (1)
Lead-Acid Batteries (for all wheeled products) (2)
HANDHELD PRODUCTS
WHEELED PRODUCTS
Reconditioned or Refurbished Products
Parts and Accessories (if purchased) (4) PARTS AND ACCESSORIES
Decks
McCulloch
Cordless products
Electric Chainsaws
Electric Lawn & Garden
Poulan Gas Chainsaws
Gas Lawn & Garden
Poulan Pro Gas Chainsaws
Engines
Transmission / Drive Systems
18
Grand
(usage
personnel
domestique
seulement)
Commercial (toute utili-
fessionnelle, agricole,
institutionnelle ou gén-
érant un revenu, autre
qu'une utilisation locative)
Location
(toute
utilisation
locative)
2 ans sans garantie sans garantie
1 an sans garantie sans garantie
2 ans sans garantie sans garantie
1 an sans garantie sans garantie
2 ans sans garantie sans garantie
2 ans sans garantie sans garantie
2 ans sans garantie sans garantie
2 ans sans garantie sans garantie
180 jours 180 jours 180 jours
Rato, LCT, Locin 2 ans 90 jours sans garantie
Tous autres Voir la note 1 Voir la note 1 Voir la note 1
Tuff Torq, General Transmission 2 ans sans garantie sans garantie
Peerless 3 ans sans garantie sans garantie
Hydro-Gear Voir la note 3 Voir la note 3 Voir la note 3
Tous autres Voir la note 3 Voir la note 3 Voir la note 3
Les tondeuses à rayon de braquage zéro et les tracteurs
autoportés avec coque du plateau de coupe estampé renforcé
bénéficient de la garantie limitée. 10 ans sans garantie sans garantie
Coque de plateau de coupe fabriqué des tondeuses à rayon de
braquage zéro et des tracteurs autoportés Voir la note 1 sans garantie sans garantie
Systèmes de collecte et sacs collecteurs 1 an 90 jours sans garantie
Tous autres accessoires (p. ex., guide-chaînes, chaînes, coffres
de transport, tête de coupe-herbe, gardes de coupe-herbe,
vêtements de protection personnels, etc.) 90 jours 30 jours sans garantie
Pièces (p. ex., courroies, lames, couvercles de démarreurs,
ressorts de démarreurs, etc.) 30 jours 30 jours sans garantie
30 jours sans garantie sans garantie
Plateaux de coupe
McCulloch
Produits sans fil
Scies à chaîne électriques
Produits de pelouse et jardin électriques
Scies à chaîne à essence Poulan
Produits de pelouse et jardin à essence
Scies à chaîne à essence professionnelles Poulan
Moteurs
Transmissions / Systèmes d'entraînement
Produits remis à neuf ou en état
Pièces et accessoires (achetés) (4) PIÈCES ET ACCESSOIRES
Poulan, Poulan Pro, Weedeater et McCulloch®
Tableau de garantie 2015
Produits de pelouse et jardin sur roues (1)
Batteries plomb-acide (pour tous les produits sur roues) (2)
PRODUITS PORTATIFS
PRODUITS SUR ROUES
public sation commerciale, pro-
1 Votre moteur est couvert par une garantie séparée du fabricant du moteur;
veuillez consulter la garantie de moteur séparée fournie avec votre produit.
2 La garantie de la batterie ne couvre pas les batteries déchargées ou non chargées.
3 La transmission Hydro-Gear est couverte par une garantie grand public de deux (2) ans, pièces et main-d'œuvre.
Souffleuses à neige et tracteurs de pelouse : la transmission Hydro-Gear est couverte par une garantie consomma-
teur de deux (2) ans, pièces et main-d'œuvre.
Pour toutes les autres marques, votre transmission est couverte par une garantie séparée du fabricant de la trans-
mission; veuillez consulter la garantie de transmission séparée fournie avec votre produit.
4 Les pièces de rechange et les accessoires fournis dans le cadre de la garantie limitée ne sont garantis que pour le
RESTE de la période de garantie applicable à la pièce ou l’accessoire remplacé.
Enregistrement du produit
Veuillez enregistrer votre produit sur le site Web correspondant : www.poulan.com;
www.poulanpro.com; www.weedeater.com; ou www.mcculloch.com
Cliquez sur “Customer Support” (Soutien à la clientèle) puis sur “Product Registration”
(Enregistrement du produit)
Vous pouvez appeler le 1-800-487-5951 (É.-U.) ou le 1-800-805-5523 (Canada) pour faire enregistrer votre produit.
Veuillez avoir toutes les informations pertinentes sous la main avant d'appeler le Soutien à la clientèle.
17
GARANTIE LIMITÉE
La couverture. Nous garantissons que ce produit est exempt de défauts de matériaux et de fabrication lors d’un us-
age et d’un entretien normaux. Certaines composantes, comme les pièces à usure normale, les moteurs et les transmis-
sions, sont exclus de la présente Garantie. Nous réparons ou remplaçons sans frais, à notre discrétion, tout produit ou
pièce défectueuses couvert par la Garantie limitée, chez tout concessionnaire réparateur Husqvarna autorisé qui utilise
les pièces de rechange du fabricant d’équipement d’origine, sous réserve des restrictions et exclusions décrites ci-après.
Période de la Garantie limitée. Nous garantissons le produit au premier acheteur au détail, à compter de la date de
l’achat au détail, pour la période de Garantie stipulée au tableau ci-dessous.
Ce qui n’est PAS couvert. La présente Garantie limitée ne couvre pas :
(a) Les moteurs et transmissions, sauf tel qu’indiqué au tableau ci-dessous; une garantie séparée fournie avec votre
produit peut s’appliquer.
(b) Les pièces à usure normale (pièces et articles qui s’usent normalement à l’usage) y compris, mais sans s’y limiter, les
bougies, ampoules, filtres, lubrifiants, cordes de lancement, courroies, lames et adaptateurs de lames, ni les dommages
causés par l’usure normale, comme l’usure par frottement des plateaux de coupe, les pneus crevés par une source
externe, la décoloration naturelle des matériaux, ainsi que l’émoussement et la détérioration des lames dus au contact
avec les abrasifs, cailloux, tiges ou autres corps étrangers.
(c) Les appareils et les composantes de contrôle des émissions, dans la mesure réglementée par la Environmental
Protection Agency des États-Unis ou d’autres agences gouvernementales semblables. Celles-ci sont couvertes par une
déclaration de garantie de lutte contre les émissions distincte contenue dans le guide de l’utilisateur.
(d) Selon le produit, il y a soit une NON-GARANTIE, soit une garantie réduite si le produit est utilisé à des fins commercia-
les, non résidentielles ou locatives et, en pareilles circonstances, la présente Garantie limitée est offerte en lieu et place
de tout régime de garantie prévu par la loi. Veuillez consulter le tableau ci-dessous.
(e) Les dommages liés au mauvais traitement, à l’usage abusif, à la négligence, aux modifications, aux changements,
à l’utilisation d’accessoires non autorisés, à l’entreposage inapproprié, au manque de lubrification ou à une panne de
moteur en raison de l’emploi de lubrifiants ne correspondant pas aux caractéristiques techniques du fabricant du mo-
teur, au nettoyage du produit à haute pression ou à la vapeur, à la saleté excessive, aux abrasifs, ainsi qu’à l’eau salée,
l’humidité, la corrosion, la rouille ou le vernis. L’omission d’effectuer l’entretien requis tel que prévu dans le guide de
l’utilisateur annulera la présente Garantie.
(f) Les dommages ou défaillances attribuables à une préparation, une pré-livraison ou une réparation inappropriée par
toute personne autre qu’un concessionnaire réparateur autorisé durant la période de Garantie.
(g) Les dommages causés par de l’essence contenant plus de 10 % (E10) d’éthanol (p. ex., E15, E25, E30, E50, E85),
l’utilisation d’éther, d’un liquide d’allumage semblable ou d’un carburant vieilli.
(h) Les dommages aux pulvérisateurs causés par l’aspersion de matières caustiques ou inflammables, ou l’absence ou
le bris de crépines.
Vos responsabilités. Pour protéger vos droits en vertu de la présente Garantie limitée, vous devez utiliser le produit en
prenant un soin raisonnable, ce qui comprend de procéder à l’entretien préventif, à l’entreposage et à l’utilisation de
carburant et de lubrifiants tel que prévu dans le guide de l’utilisateur. Tout réglage (p. ex., du câble d’accélérateur ou
des guide-courroie) après les trente premiers jours suivant l’achat et tout entretien préventif décrit dans le guide de
l’utilisateur ne sont PAS couverts. De plus, vous devez cesser d’utiliser le produit immédiatement, en cas de défaillance
ou d’avarie, et l’apporter à un concessionnaire réparateur autorisé avant toute utilisation ultérieure.
EXCLUSIONS DE GARANTIE, EXONÉRATIONS ET DROITS LIMITÉS. NOUS NE SOMMES RESPONSABLES
D’AUCUN DOMMAGE INDIRECT OU CONSÉCUTIF. VOTRE RECOURS SE LIMITE À LA RÉPARATION OU AU REM-
PLACEMENT DU PRODUIT OU DE LA PIÈCE, À NOTRE DISCRÉTION. IL N’Y A AUCUNE AUTRE GARANTIE EXPRESSE
QUE CELLES EXPRIMÉES AUX PRÉSENTES. TOUTE GARANTIE IMPLICITE EN VERTU DE LA LOI DE L’ÉTAT (QU’ELLE
SOIT RELATIVE À LA QUALITÉ MARCHANDE, À UNE APTITUDE À UNE UTILISATION PARTICULIÈRE OU AUTREMENT)
EST DÉCLINÉE PAR LES PRÉSENTES; LÀ OÙ DE TELLES EXONÉRATIONS NE SONT PAS PERMISES PAR LA LOI, AL-
ORS LA PRÉSENTE GARANTIE IMPLICITE SE LIMITE À LA DURÉE DE LA GARANTIE LIMITÉE QUI S’APPLIQUE, COM-
ME ÉNONCÉ DANS LE TABLEAU CI-DESSOUS. CERTAINES RÉGIONS, PARMI LESQUELLES LE QUÉBEC, NE PER-
METTENT PAS L’EXCLUSION DE DOMMAGES INDIRECTS OU CONSÉCUTIFS OU LES LIMITATIONS SUR LA DURÉE
DES GARANTIES IMPLICITES, SI BIEN QUE LES LIMITATIONS CI-DESSUS PEUVENT NE PAS S’APPLIQUER À VOUS.
LA PRÉSENTE GARANTIE LIMITÉE VOUS DONNE DES DROITS JURIDIQUES PRÉCIS ET VOUS POUVEZ AUSSI AVOIR
D’AUTRES DROITS SELON VOTRE RÉGION.
Comment obtenir les services. Pour obtenir les services sous garantie, vous devez apporter votre produit à un conces-
sionnaire réparateur autorisé. Pour trouver le concessionnaire réparateur autorisé le plus proche, visitez notre site Web
et utilisez l’onglet Trouver un concessionnaire, ou appelez le 1 800 805-5223 entre 8 heures et 19 heures (HNE). Tous les
frais de transport ou d’expédition du produit sont à votre charge. Vous devez présenter la preuve d’achat (comportant
la date, le modèle du produit et son numéro de série) à un concessionnaire réparateur autorisé pour les services sous
garantie. La preuve d’achat est votre entière responsabilité. Vous pouvez enregistrer votre produit à l’aide de notre
site d’inscription du produit en ligne pour vous assurer d’être avisé(e) d’importants renseignements sur les produits.
L’enregistrement du produit n’est toutefois pas une condition des services sous garantie.
587 70 47-01 Rev. A 2014-09-30
2015
www.poulan.com www.poulanpro.com www.weedeater.com www.mcculloch.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Poulan Pro HDF900 Manuel utilisateur

Catégorie
Mini motoculteurs
Taper
Manuel utilisateur

dans d''autres langues