Axis P3343-VE Guide d'installation

ENGLISH DEUTSCH ITALIANO ESPAÑOL

INSTALLATION GUIDE

FRAN

Ç

AIS

AXIS P3343-VE Network Camera

AXIS P3344-VE Network Camera

AXIS P3346-VE Network Camera

About this Document

This document includes instructions for installing AXIS

P3343-VE, AXIS P3344-VE and AXIS P3346-VE on your

network. Previous experience of networking will be

beneficial when installing the product.

Legal Considerations

Video and audio surveillance can be prohibited by laws

that vary from country to country. Check the laws in

your local region before using this product for

surveillance purposes.

This product includes one (1) H.264 decoder license. To

purchase further licenses, contact your reseller.

Electromagnetic Compatibility (EMC)

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures: Re-orient or relocate

the receiving antenna. Increase the separation between

the equipment and receiver. Connect the equipment to

an outlet on a different circuit to the receiver. Consult

your dealer or an experienced radio/TV technician for

help. Shielded (STP) network cables must be used with

this unit to ensure compliance with EMC standards.

USA - This equipment has been tested and found to

comply with the limits for a Class B computing device

pursuant to Subpart B of Part 15 of FCC rules, which are

designed to provide reasonable protection against such

interference when operated in a commercial

environment. Operation of this equipment in a

residential area is likely to cause interference, in which

case the user at his/her own expense will be required to

take whatever measures may be required to correct the

interference.

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for radiated emission according to limit B

of EN55022, and the requirements for immunity

according to EN55024 residential and commercial

industry.

Japan - This is a class B product based on the standard

of the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this is used

near a radio or television receiver in a domestic

environment, it may cause radio interference. Install and

use the equipment according to the instruction manual.

Australia - This electronic device meets the

requirements of the Radio communications

(Electromagnetic Compatibility) Standard AS/NZS

CISPR22.

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB

cannot be held responsible for any technical or

typographical errors and reserves the right to make

changes to the product and documentation without

prior notice. Axis Communications AB makes no

warranty of any kind with regard to the material

contained within this document, including, but not

limited to, the implied warranties of merchantability

and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible

for incidental or consequential damages in connection

with the furnishing, performance or use of this material.

RoHS

This product complies with both the European

RoHS directive, 2002/95/EC, and the Chinese

RoHS regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member

states.

The WEEE marking on this product (see right) or its

documentation indicates that the product must not be

disposed of together with household waste. To prevent

possible harm to human health and/or the environment,

the product must be disposed of in an approved and

environmentally safe recycling process. For further

information on how to dispose of this product correctly,

contact the product supplier, or the local authority

responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly.

This product should not be mixed with other commercial

waste. For more information, visit

www.axis.com/techsup/commercial waste

Support

Should you require any technical assistance, please

contact your Axis reseller. If your questions cannot be

answered immediately, your reseller will forward your

queries through the appropriate channels to ensure a

rapid response. If you are connected to the Internet, you

can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area.

AXIS P3343-VE, AXIS P3344-VE, and AXIS P3346-VE

Network Cameras use a 3.0V CR2032 Lithium battery.

ENGLISH

Safeguards

Please read through this Installation Guide carefully before installing the product. Keep the Installation Guide

for further reference.

CAUTION!

• When transporting the Axis product, use the original packaging or equivalent to prevent damage to the

product.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install the camera on

unstable brackets, unstable or vibrating surfaces or walls, since this could cause damage to the product.

• Only use handtools when installing the Axis product, the use of electrical tools or excessive force could

cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.

• Only use accessories and spare parts provided or recommended by Axis.

• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters.

IMPORTANT!

• This Axis product must be used in compliance with local laws and regulations.

Battery replacement

This Axis product uses a 3.0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC).

Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the

operation of the RTC, causing it to reset at every power-up. A log message will appear when the battery needs

replacing. The battery should not be replaced unless required!

If the battery does need replacing, please contact www.axis.com/techsup for assistance.

• Danger of Explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent battery, as recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer's instructions.

Cleaning of dome cover

• Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to the eye

and never polish the surface. Excessive cleaning can damage the surface.

• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral soap or

detergent with water and a soft cloth. Rinse well with clean lukewarm water. Dry with a soft cloth to pre-

vent water spotting.

• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct sunlight or at

elevated temperatures.

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 5

ENGLISH

AXIS P33-VE Series Network Camera

Installation Guide

Follow these instructions to install the network camera

1. “Package contents” on page 5

2. “Hardware overview” on page 6

3. “Install the hardware” on page 7

4. “Assign an IP address” on page 10

5. “Set the password” on page 13

6. “Adjust the Lens” on page 15

7. “Complete the installation” on page 16

Notes:

• Before you begin, make sure that the package contents, power supply, and the required cables, tools, and

documentation are available. See Package contents below.

• This network camera is intended to operate with PoE; if not available use Axis PoE Midspan 1 port (not

included)

Package contents

Item Models/variants/notes

Network camera

with heating module AXIS P3343-VE

AXIS P3344-VE

AXIS P3346-VE

Mounting bracket

Dome covers Clear transparent cover

Smoked transparent cover

Cable shield

Weather shield

Labels 2 adhesive serial no. labels

Mounting kit Resitorx screw driver, drill template, 5-meter network cable with gasket

4 screws and plugs, 2 long screws, 2 M4x8 screws

1 gasket, terminal block connector

CD AXIS Network Video Product CD including product documentation,

installation tools and other software

Printed Materials Installation Guide (this document)

Axis Warranty Document

AVHS Authentication key

Optional accessories See www.axis.com for information on available accessories

Important!

This product must be used in

compliance with local laws and

regulations.

Page 6 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

Hardware overview

Caution!

The heater in the camera unit may be hot.

Dimension (HxW)

AXIS P3343-VE/AXIS P3344-VE = 110 x 179 mm (4.3 x 7.105")

AXIS P3346-VE = 117 x 179 mm (4.59” x 7.05”)

Weight

AXIS P3343-VE/AXIS P3344-VE = 1.4 kg (3.09 lb.)

AXIS P3346-VE = 1.6 kg (3.5 lb)

Fan output

connector

Unit casing

Camera unit Dome cover

Holes for cables

routed through the wall Side holes with

Network connector LED indicators Control button

Camera unit

Audio in

(PoE)

Audio out

SD memory card slot

Serial no.

Heater

Weather shield

Spring

routed along the wall

for cablesgaskets

I/O connector

Mounting bracket

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 7

ENGLISH

Install the hardware

Prepare the network cable

If a cable other than the provided cable is used, you need to prepare a network cable with a gasket.

Gently force the cable through the gasket provided and attach a network connector. It may be

necessary to pierce a hole in the gasket with the resitorx screwdriver.

Notes:

• Do not force the network connector into the gasket.

• Do not pierce the gasket with a knife or other sharp object.

Prepare the unit casing (routing cables along the wall)

If the cables are to be routed along the wall, prepare the unit casing as follows:

1. Detach the side lid that is attached to the unit casing by removing the screw.

2. Loosen the two screws on the cable shield and detach the bottom part.

3. Attach the bottom part of the cable shield to the unit casing with the screw.

Replace clear/smoked dome cover (optional)

The AXIS P3343-VE/P3344-VE/P3346-VE is supplied with an optional dome. To replace the dome

cover:

1. Loosen the 4 screws under the dome cover that hold the dome in place.

2. Transfer the gasket from the old dome to the new.

3. Replace the old dome with the new and tighten the screws.

Side lid

Screw

Top part

Bottom part

Unit casing Cable shield Unit casing

Page 8 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

Route the cables

Depending on whether you want to route the cables through or along the wall, follow the relevant

instructions below.

Routing cables along the wall

1. Using the drill template drill 4 holes in the wall.

2. Attach the mounting bracket to the wall using the 4 screws provided, or screws appropriate for

the wall material.

3. Remove the camera unit from the unit casing by pushing the springs aside.

4. Remove the gaskets from the side holes in the unit casing. If there is only one cable, remove

only one gasket.

5. Place the unit casing on the mounting bracket and attach it by tightening the four screws.

6. Pull the cables up through the side holes in the unit casing.

7. Drag the gaskets along the cable and plug them into the holes. The gaskets should fit snugly in

the holes with no folds or bends.

8. Re-attach the top part of the cable shield by tightening the two screws.

Note: To avoid moisture-related problems it is recommended that the cables are routed to the camera

from below with the cable holes facing downwards.

Routing cables through the wall

1. Using the drill template drill 4 holes in the wall.

2. Route the network cable (and the I/O, audio cable if necessary) through the wall and through

the holes in the mounting bracket.

3. Attach the mounting bracket to the wall using the 4 screws provided, or screws appropriate for

the wall material.

4. Remove the camera unit from the unit casing by pushing the springs aside.

5. Remove the gaskets from the back holes in the unit casing. If there is only one cable, remove

only one gasket.

6. Route the cables through these holes.

7. Drag the gaskets along the cables and plug them into the holes. The gaskets should fit snugly in

the holes with no folds or bends.

8. Attach the unit casing to the

mounting bracket by tightening

the four screws.

Mounting bracket

Network cable with gasket

Unit casing

Remove gaskets

from holes

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 9

ENGLISH

Install the camera unit

1. Attach the network cable to the camera unit; and the cable for audio and I/O if required. It is

recommended that the network cable is twisted to a loop as shown in the illustration above.

Note: Be careful not to stretch or bend the network cable too much since this could cause damage to

the network cable.

2. Insert the SD memory card (optional).

3. Pull aside the springs in the unit casing and click the camera unit in place.

4. Attach the fan connector to the connector in the camera unit.

5. Attach the two M4x8 20 screws to the camera for greater stability.

These screws are only necessary to secure against heavy shocks and vibrations.

Note: The AXIS P3343-VE/P3344-VE/P3346-VE can also be fitted

with a metal conduit for protecting the cabling when

cables are routed along the wall.

Connector for fan

Camera unit

Network cable

Attach

screw to camera

Conduit

Page 10 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

Assign an IP address

The AXIS P3343-VE/P3344-VE/P3346-VE Network Camera is designed for use on an Ethernet

network and requires an IP address for access. Most networks today have a DHCP server that

automatically assigns IP addresses to connected devices. If your network does not have a DHCP

server, the AXIS AXIS P3343-VE/P3344-VE/P3346-VE Network Camera will use 192.168.0.90 as the

default IP address.

AXIS IP Utility and AXIS Camera Management are the recommended methods for setting an IP

address in Windows. These free applications are available on the Axis Network Video Product CD

supplied with this product, or they can be downloaded from www.axis.com/techsup Depending on

the number of cameras you wish to install, use the method that suits you best.

Notes:

• If you are unable to set the IP address, check for any firewall blocking the operation.

• See page 17 for other available methods for setting or discovering the IP address of the AXIS

P3343-VE/P3344-VE/P3346-VE Network Camera, in relation to other operating systems.

Method Recommended for Operating system

AXIS IP Utility

See page 11 Single camera

Small installations Windows

AXIS Camera Management

See page 12 Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

Windows 7

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 11

ENGLISH

AXIS IP Utility - single camera/ small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. You can also

manually set a static IP address through this application. AXIS IP Utility is available on the Axis

Network Video Product CD, or it can be downloaded from www.axis.com/techsup

Note that you must install the AXIS P3343-VE/P3344-VE/P3346-VE Network Camera on the same

network segment (physical subnet) as the computer running AXIS IP Utility.

Automatic discovery

1. Check that the AXIS P3343-VE/P3344-VE/P3346-VE Network Camera is connected to the

network and that power has been applied.

2. Start AXIS IP Utility.

3. When AXIS P3343-VE/P3344-VE/P3346-VE appears in the window, double-click to open the

camera’s home page.

4. See page 13 for instructions on how to set the password.

Set the IP address manually (optional)

1. Acquire an unused IP address on the same network segment your computer is connected to.

2. Select the AXIS P3343-VE/P3344-VE/P3346-VE in the list.

3. Click the button Assign new IP address to selected device and enter the IP address.

4. Click the Assign button and follow on-screen instructions. Note that the camera must be

restarted within two minutes for the new IP address to be set.

5. Click the Home Page button to access the camera’s web pages.

6. See page 13 for instructions on how to set the password.

Page 12 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show connection

status, manage firmware upgrades, and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the camera appears in the window, right-click the link

and select Live View Home Page.

3. See page 13 for instructions on how to set the password.

Assign an IP address in a single device

1. Select AXIS P3343-VE/P3344-VE/P3346-VE in AXIS Camera

Management and click the Assign IP button .

2. Select Assign the following IP address and enter the IP

address, the subnet mask, and default router the device will

use.

3. Click OK.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of assigning IP

addresses to multiple devices, by suggesting IP addresses from a

specified range.

1. Select the devices you wish to configure (different models can be

selected) and click the Assign IP button .

2. Select Assign the following IP address range and enter the range

of IP addresses, the subnet mask, and default router the devices will use.

3. Click the OK button.

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 13

ENGLISH

Set the password

To gain access to the product, the password for the default administrator user root must be set. This

is done in the Configure Root Password dialog, which is displayed when the

AXIS P3343-VE/P3344-VE/P3346-VE is accessed for the first time.

To prevent network eavesdropping when setting the root password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate.

To set the password via a standard HTTP connection, enter it in the Configure Root Password

window.

To set the password via an encrypted HTTPS connection, follow these steps:

1. Click the Create self-signed certificate button.

2. Provide the requested information and click OK. The certificate is created and the password can

now be set securely. All traffic to and from the AXIS P3343-VE/P3344-VE/P3346-VE Network

Camera is encrypted from this point on.

3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now

been configured.

4. To log in, enter the user name “root” in the dialog as requested.

Note: The default administrator user name root cannot be deleted.

5. Enter the password as set above, and click OK. If the password is lost, the AXIS

P3343-VE/P3344-VE/P3346-VE must be reset to the factory default settings. See page 21.

The Live View page of the AXIS P3343-VE/P3344-VE/P3346-VE appears. The Setup link to the right

gives you menu options that allow you to customize the camera.

To configure the password directly via an

unencrypted connection, enter the password

here.

To create an HTTPS connection, start by clicking

this button.

Page 14 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

6. The capture mode must be set the first time the

network camera is accessed. Select the desired

capture mode from the drop-down list and click OK.

Note: The capture mode can be changed later from the prod-

uct’s web pages, but this will reset most other settings.

For more information, see the online help or User’s

Manual.

7. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video

stream in Internet Explorer. You will need administrator rights on the computer to do this.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as administrator.

Right-click the Internet Explorer icon and select Run as administrator.

Access the video stream

The Live View page of the network camera is displayed. The Setup link leads to menus which allow

you to customize the camera.

Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as an administrator.

Right-click the Internet Explorer icon and select Run as administrator.

AXIS P3346

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 15

ENGLISH

Adjust the Lens

Open the Live View page in the web interface and make the following adjustments to the camera:

1. Loosen the locking screw and tilt adjustment screws.

2. Turn the lens (with the lens holder) to the desired position. Make sure the horizontal lines on

either side of the lens are aligned horizontally

Note: Ensure that the mark on the lens cover, between the horizontal lines, is facing up.

3. Once satisfied, gently tighten the locking screw and tilt adjustment screws to secure the

camera’s position.

4. Open the Focus Adjustment page in the Web interface under Setup > Focus & Zoom, and

follow the on-screen instructions. Use the image window to adjust the focus and zoom.

Go to Setup > Video & Image > Advanced in your web interface and see the online help for

more information.

Note: Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been

placed. To correct this go to the Focus Adjustment page in the Web interface under

Setup >Focus & Zoom, and adjust the focus again.

Warning! Adjusting the focus and zoom manually can damage the lens.

Locking screw

Tilt adjustment screw

Horizontal line

Tilt adjustment screw

Page 16 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

Complete the installation

1. Rotate the black protective shield inside the dome cover

so it is aligned with the camera’s position.

2. If required, attach the weather shield to the camera before

you attach the dome cover. To do this remove the two

screws in the dome cover. Transfer the washers from these

screws to the two long screws provided. Attach the weather shield using the two long screws.

3. Attach the dome cover to the unit casing by tightening the 4 screws.

Black protective

shield

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 17

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address. All

methods are enabled by default, and all can be disabled.

AXIS Video Hosting System (AVHS)

The camera can also be connected to an AVHS service for hosted video. If you have subscribed to an

AVHS service, follow the instructions in the Service Provider’s Installation Guide. For more

information and help to find a local AVHS Service Provider, go to www.axis.com/hosting The camera

owner authentication key is supplied with this product. The key is associated with the camera’s

unique serial number (S/N) as shown on the top of the label.

Note: Save the key for future reference.

Use in operating

system Notes

UPnP™

Windows When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later) Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Page 18 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

Set the IP address with ARP/Ping

1. Acquire a free static IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS P3343-VE/P3344-VE/P3346-VE label.

3. Open a command prompt on your computer and enter the following commands:

4. Restart the AXIS P3343-VE/P3344-VE/P3346-VE, by disconnecting and reconnecting the

network cable.

5. Close the command prompt when you see ‘Reply from 192.168.0.125:...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on

your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using shielded

cables is recommended.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from

a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an

active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo

connector must be used for the audio out.

SDHC memory card slot - The high capacity SD memory card can be used for local recording with

removable storage.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide Page 19

ENGLISH

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications. It provides the

interface to:

• 1 transistor output - For connecting external devices such as

relays and LEDs. Connected devices can be activated by the

VAPIX Application Programming Interface (API), by the output buttons on the Live View

page or by an Event Type. The output will show as active (shown under Event Configu-

ration > Port Status) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between an

open and closed circuit, for example: PIRs, door/window contacts, and glass break

detectors. When a signal is received the state changes and the input becomes active

(shown under Event Configuration > Port Status).

• Auxiliary power and GND

The following connection diagram gives an example of how to connect an auxiliary device to the

AXIS P3343-VE/P3344-VE/P3346-VE.

Function Pin Notes Specifications

GND 1 Ground

3.3V DC

Power 2 Can be used to power auxiliary equipment.

Note: This pin can only be used as power out. Max. load = 50mA

Digital

Input 3 Connect to GND to activate, or leave floating (or

unconnected) to deactivate. Min. input= - 40V DC

Max. input= + 40V DC

Digital

Output 4 Uses an open-drain NFET transistor with the source

connected to GND. If used with an external relay, a

diode must be connected in parallel with the load,

for protection against voltage transients.

Max. load = 100mA

Max voltage = + 40V DC

Pin1

Pin2

Pin3

Pin4

1

2

E.g. push button

3

4

3.3V

max. 50mA

D

S

G

Page 20 AXIS P3343-VE/P3344-VE/P3346-VE Installation Guide

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Amber Steady during startup; flashes once during reset to factory default or while

restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

La page charge ...

Axis P3343-VE Guide d'installation

Ce manuel convient également à

Axis P3343-VE Guide d'installation

dans d''autres langues

Documents connexes

Autres documents