Connect the telephone base
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc.
All rights reserved. 06/22. CS5229-X_QSG_V6.0
HSDCX79-BSDCX81
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of the
Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY
STAR® label indicating it meets the latest energy efficiency guidelines.
Frequency
control Crystal controlled PLL synthesizer
Transmit
frequency Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels DECT channel: 5
Nominal
effective
range
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Power
requirement
Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 0.4A
Charger: 6V DC @ 0.4A
Memory Directory: 50 memory locations;
up to 30 digits and 15 characters
Caller ID log: 30 memory locations;
up to 24 digits and 15 characters
Call block: 150 entries
If you subscribe to digital subscriber line (DSL)
high-speed Internet service through your
telephone line, make sure you connect a DSL
filter (not included) to the telephone wall jack.
Quick start guide
CS5229
CS5229-2
CS5229-3
CS5229-4
CS5229-5
DECT 6.0 cordless telephone
Quick
start
guide
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1939
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
THIS SIDE UP
Install the battery
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
Connect the charger
Charge the battery
10 hrs
The battery is low and
needs charging.
The battery is charging.
The battery is fully charged.
Handset ringer is off.
New voicemail received
from your telephone
service provider.
NEW
There are new caller ID log
entries.
ANS ON Answering system is on.
MUTE The handsest microphone
is muted while on a call.
10:30
PM
AM Time with AM and PM.
5
/
10
MSG# Number of new/old
messages recorded.
Display After you install your telephone or power returns
following a power outage and battery depletion, the
handset will prompt you to set the date and time, and to
configure the answering system through voice guide.
Voice guide for answering system
After setting the date and time, the handset will display
Voice guide to set up Ans sys?.
This feature assists you to do the basic setup of the
answering system. You can follow the voice guide to record
your own announcement, set the number of rings and the
message alert tone.
2
Press SELECT.
3
Enter the time.
4
Press SELECT.
SET DATE
12/25/19
SET TIME
10:59 AM
Voice guide to
set up Ans sys?
SET DATE
12/2?/YY
“Hello! This voice guide
will assist you with the
basic setup of your
answering system“
When the handset
prompts you to set
the date and time
When the handset
prompts you to set up
the answering system
via voice guide
Directory
The directory can store up to 50 entries, which are shared by
all handsets. Each entry may consist of a telephone number
up to 30 digits, and a name up to 15 characters.
Add a directory entry
1
Enter the phone
number. 2
Press MENU.
3
Press SELECT.
HANDSET
ANS ON
10:15PM 12/ 25
595-9511_
4
Enter the name.
5
Press SELECT.
ENTER NAME
_
ENTER NAME
Mike Smiths_
Review directory entries
Delete a directory entry
Mike Smith
800-595-9511
Mike Smith
Delete contact?
1
Press DELETE.
2
Press SELECT.
1
Press .
2
Press / to
browse the entries.
Mike Smith
800-595-9511
ENTER NUMBER
595-9511
When your desired
directory entry displays on
the handset screen
Caller ID
If you subscribe to caller ID service, information about
each caller appears after the first or second ring.
The caller ID log stores up to 30 entries. Each entry has
up to 24 digits for the phone number and 15 characters
for the name.
Review caller ID log entries
1
Press .
2
Press / to
browse the entries.
Mike Smith
595-9511
NEW
ANS ON
Dial a caller ID log entry
3
Edit the phone
number
if needed.
4
Press SELECT.
5
Edit the name
if needed, then
press SELECT.
EDIT NUMBER
595-9511_
EDIT NUMBER
800-595-9511_
1
Press MENU.
2
Press SELECT
to select
Directory.
>Directory
Caller ID log
Mike Smith
595-9511
NEW
ANS ON
EDIT NAME
Mike Smiths_
Save a caller ID log entry to the directory
Delete a caller ID log entry
Mike Smith
595-9511
NEW
ANS ON
When your
desired caller ID
entry displays
on the handset
screen
When your
desired caller ID
entry displays
on the handset
screen
When your
desired caller ID
entry displays
on the handset
screen
Press
- OR -
1 set for CS5229-2
2 sets for CS5229-3
3 sets for CS5229-4
4 sets for CS5229-5
1 set for CS5229
2 sets for CS5229-2
3 sets for CS5229-3
4 sets for CS5229-4
5 sets for CS5229-5
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or
loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers
assume no responsibility for any loss or claims by third parties that may arise through the use
of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
SET TIME
1?:MM --
Date and time
Follow the steps below to set the date and time. For
example, if the date is 25 December, 2019, and the time is
10:59 AM:
SET DATE
MM/DD/YY
Speakerphone
Press
End a call
Answer a call
Make a call
Setup your answering system by inputting the
designated numbers as instructed in the voice guide.
Press DELETE
to delete.
Disclaimer and Limitation of Liability
Technical specifications
Press SELECT.
1 Press - OR -
2
Enter the
phone number
Press - OR - - OR - Press any dialing
keys to answer
Press
What’s in the box
1
Connect and activate
2
Setup
Basic operation Directory Caller ID
Important
safety
instructions
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for
cleaning.
4. CAUTION: Do not install the telephone
base at a height above 2 meters.
5. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or a swimming pool, nor in a
wet basement or shower.
6. Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
7. Avoid placing the telephone system in
places with extreme temperature, direct
sunlight, or other electrical devices. Protect
your phone from moisture, dust, corrosive
liquids and fumes.
8. Slots and openings in the back or bottom
of the telephone base and handset are
provided for ventilation. To protect them
from overheating, these openings must not
be blocked by placing the product on a
soft surface such as a bed, sofa or rug. This
product should never be placed near or
over a radiator or heat register. This product
should not be placed in any area where
proper ventilation is not provided.
9. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure of
the type of power supply in your home or
office, consult your dealer or local power
company.
10. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
11. Never push objects of any kind into this
product through the slots in the telephone
base or handset because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the telephone base or
handset other than specified access doors
may expose you to dangerous voltages
or other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
13. Do not overload wall outlets and extension
cords.
14. Unplug this product from the wall outlet
and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the
product.
• If the product has been exposed to rain
or water.
• If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage
and often requires extensive work by
an authorized technician to restore the
product to normal operation.
• If the product has been dropped and
the telephone base and/or handset has
been damaged.
• If the product exhibits a distinct change
in performance.
15. Avoid using a telephone (other than
cordless) during an electrical storm. There
is a remote risk of electric shock from
lightning.
16. Do not use the telephone to report a
gas leak in the vicinity of the leak. Under
certain circumstances, a spark may be
created when the adapter is plugged into
the power outlet, or when the handset is
replaced in its cradle. This is a common
event associated with the closing of any
electrical circuit. The user should not plug
the phone into a power outlet, and should
not put a charged handset into the cradle,
if the phone is located in an environment
containing concentrations of flammable
or flame-supporting gases, unless there
is adequate ventilation. A spark in such
an environment could create a fire or
explosion. Such environments might
include: medical use of oxygen without
adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a
leak of natural gas; etc.
17. Only put the handset of your telephone
next to your ear when it is in normal talk
mode.
18. The power adapter is intended to be
correctly oriented in a vertical or floor
mount position. The prongs are not
designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or
cabinet outlet.
19. For pluggable equipment, the socket-outlet
shall be installed near the equipment and
shall be easily accessible.
20. CAUTION: Use only the
batteries indicated in this manual. There
may be a risk of explosion if a wrong type
of battery is used. Use only the supplied
rechargeable batteries or replacement
batteries (BT162342/BT262342). Do not
dispose of batteries in a fire. They may
explode. Dispose of used battery according
to the instruction. Disconnect the telephone
line from the equipment before open the
battery door.
• Do not use the battery in following
conditions:
» High or low extreme temperature
during use, storage or
transportation.
» Replacement of a battery with an
incorrect type that can defeat a
safeguard.
» Disposal of a battery into fire or a
hot oven, or mechanically crushing
or cutting of a battery, that can
result in an explosion.
» Leaving a batteryin an extremely
high temperature surrounding
environment that can result in
an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely
low air pressure that can result in
an explosion or the leakage of
flammable liquid or gas.
21. Use only the adapter included with this
product. Incorrect adapter polarity or
voltage can seriously damage the product.
22. The applied nameplate is located at the
bottom or near of the product.
SAVE THESE INSTRUCTIONS
Battery
• Use only the batteries provided or
equivalent. To order a replacement, visit our
website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or call
1 (800) 267-7377.
• Do not dispose of the battery in a fire.
Check with local waste management codes
for special disposal instructions.
• Do not open or mutilate the battery.
Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The
electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless telephones and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six
inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the
ear opposite the pacemaker.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless telephones.
About cordless
telephones
• Privacy: The same features that make a
cordless telephone convenient create some
limitations. Telephone calls are transmitted
between the telephone base and the
cordless handset by radio waves, so there
is a possibility that the cordless telephone
conversations could be intercepted by
radio receiving equipment within range
of the cordless handset. For this reason,
you should not think of cordless telephone
conversations as being as private as those
on corded telephones.
• Electrical power: The telephone base of
this cordless telephone must be connected
to a working electrical outlet. The electrical
outlet should not be controlled by a wall
switch. Calls cannot be made from the
cordless handset if the telephone base is
unplugged, switched off or if the electrical
power is interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference,
do not place the telephone base of the
cordless telephone near or on top of a TV or
VCR. If interference is experienced, moving
the cordless telephone farther away from
the TV or VCR often reduces or eliminates
the interference.
• Rechargeable batteries: Exercise care in
handling batteries in order not to create a
short circuit with conducting material such
as rings, bracelets and keys. The battery or
conductor may overheat and cause harm.
Observe proper polarity between the
battery and the battery charger.
• Nickel-metal hydride rechargeable
batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury.
Volume
Press
1Enter the date.
LCD language setting
If you accidentally set the LCD language to Spanish or French,
press MENU and then enter 364# to change the handset LCD
language back to English while the handset is not in use.
Go to
www.vtechphones.com (US)
to register your product for
enhanced warranty support
and latest VTech product news.
Go to
phones.vtechcanada.com (CA)
for latest VTech product news.
Scan the QR code for
support information
CS5229-X (CA)
CS5229-X (US)
HANDSET
MUTE NEW
ANS ON
10:30
PM
AM
5
/
10
MSG#
HANDSET
ANS ON
10:15PM 12/ 25
HANDSET
ANS ON
10:15PM 12/ 25 10:15 12/ 25
AM
Mike Smith
595-9511
NEW
ANS ON
10:15 12/ 25
AM
10:15 12/ 25
AM
10:15 12/ 25
AM
About the built-in answering system and voicemail service
For message recording, your telephone has a built-in answering system, and it also supports voicemail service offered by your
telephone service provider (subscription is required, and fee may apply).
Built-in answering system VS Voicemail service
Turn the built-in answering system on or off
On the telephone base
HANDSET
ANS ON
Built-in answering system Voicemail service
Supported by Telephone system Telephone service provider
Subscription No Yes
Fees No May apply
Answer incoming calls • After 4 rings by default.
• It can be changed via handset menu.
• Usually after 2 rings.
• It can be changed by contacting your telephone service provider.
Storage Telephone base Server or System
Display new messages • Handset - XX New messages
• Telephone base - Message window flashes • Handset - and New voicemail
Retrieve messages
• Press on the telephone base; OR
• Press MENU, and then select Play messages
on the handset; OR
• Access remotely with an access code.
• Press on the dialpad, and enter an access number and/or
passcode from your telephone service provider; OR
• Press and hold to dial if you have saved the access number.
Set number of rings
You can set your answering system to answer calls at least two rings
earlier than your voicemail service. For example, if your voicemail
service answers after six rings, set your answering system to answer
after four rings. Thus, if you are on a call, or if the answering system is
busy recording a message and you receive another call, the second
caller can leave a voicemail message.
Play messages
>Answering sys
Voice gide
>Ans sys setup
Call screening
># of rings
# OF RINGS
>4
For operations and guides to help you using your telephone, and for latest information
and supports, go and check the online help topics and online FAQs.
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/cs5229; OR
• Scan the QR code on the right. Launch the camera
app or QR code scanner app on your smartphone
or tablet. Hold the device’s camera up to the QR
code and frame it. Tap the notification to trigger the
redirection of the online help.
- If the QR code is not clearly displayed, adjust
your camera’s focus by moving your device
closer or further away until it is clear.
You can also call our Customer Support at
1 (800) 595-9511 [in US] or 1 (800) 267-7377 [in Canada]
for help.
Message playback
On the telephone base
On a handset
1
Press MENU.
2
Press SELECT
to select Play messages.
>Play messages
Answering sys
HANDSET
ANS ON
- OR -
Press
1
2
Delete all messages
Skip a message
Repeat the playing message
Play the previous message
Press
1
2
- OR - 1 2
•
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas
de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement
humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2
mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier
de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous
la douche.
6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil
pourrait tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits soumis à une température
extrême, à la lumière directe du soleil ou à proximité immédiate d’autres appareils
électriques ou électroniques. Protégez votre téléphone contre les sources
d’humidité, la poussière, les vapeurs et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière
ou en dessous. Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être
obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires.
Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une plinthe
électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé
qui ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les
étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre maison,
consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit
sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le
cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils
pourraient toucher à des points de tension dangereux ou court-circuiter des pièces,
ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez pas de
liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut être à l’origine d’une électrocution lors
d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder
au nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en respectant les instructions de
fonctionnement. Réglez uniquement les commandes indiquées dans le les
instructions de fonctionnement. Les réglages incorrects des autres commandes
pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de
la part d’un technicien autorisé afin de rétablir le fonctionnement normal de
l’appareil.
• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs
peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite.
En certaines circonstances, une flammèche pourrait être provoquée lorsque
l’adaptateur est branché à une prise de courant, ou lorsque le combiné est
déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un
circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de
courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone
se trouve à proximité d’un endroit comportant des concentrations de gaz
inflammables, à moins que la ventilation soit adéquate. Une flammèche dans un tel
endroit pourrait provoquer un incendie ou une explosion. De tels environnements
peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans
ventilation adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode
de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au
sol. Les broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci
est barnché dans une prise au plafond ou sous une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant
doit etre installe a proximite du materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez
le mauvais type de piles pour le téléphone. N’utilisez que les piles rechargeable
inclus ou les piles de rechange (BT162342/BT262342). N’incinérez pas les
piles. Celles-ci risqueraient d’exploser. Mettre au rebut les batteries usagées
conformément aux instructions du fabricant. Débrancher les lignes téléphoniques
avant le remplacement des piles.
• Évite d’utiliser la batterie dans les conditions suivantes:
» des températures extrêmes faibles ou élevées auxquelles une batterie peut
être soumise pendant l’utilisation, le stockage ou le transport;
» Remplacement d’une batterie par un type incorrect pouvant supprimer une
protection;
» mise au rebut d’une batterie dans un feu ou dans un four chaud, ou
écrasement mécanique ou coupure d’une batterie, susceptible de
provoquer une explosion;
» maintien d’une batterie dans un environnement à très haute température
pouvant provoquer une explosion ou la fuite de liquide ou de gaz
inflammables;
» batterie soumise à une pression de l’air extrêmement faible pouvant
provoquer une explosion ou la fuite de liquide ou de gaz inflammables.
21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur
dont la polarité ou la tension serait inadéquate risque d’endommager
sérieusement le produit et mettre votre sécurité en péril.
22. La plaque signalétique appliquée est située au bas ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent. Pour commander une pile de recharge,
visitez notre site Web au www.vtechphones.com ou composez le 800-595-9511. Au
Canada, visitez le phones. phones.vtechcanada.com ou composez le 800-267-7377.
• Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus
auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif
et pourrait causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte
est toxique si avalé.
• Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits
provoqués par des matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spécifiées
dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans
fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche
indépendante, a mené une évaluation pluridisciplinaire des interférences entre les
téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du
stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur
cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans
la direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs
de simulateurs cardiaques causés par les gens qui utilisent un téléphone sans fil à
proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les
téléphones sans fil affichent également des restrictions. Les appels téléphoniques
sont transmis entre le combiné sans fil et le socle par le biais d’ondes radio ; il y a donc
la possibilité que vos conversations téléphoniques sans fil soient interceptées par des
équipements de réception radio se trouvant dans la portée du combiné sans fil. Pour
cette raison, vous ne devez pas percevoir les communications téléphoniques sans fil
comme étant aussi confidentielles que celles des téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une
prise électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un
interrupteur mural. Les appels ne pourront pas être effectués du combiné sans fil si le
socle est débranché ou mis hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent
sur des fréquences pouvant causer des interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir de telles interférences, ne placez pas le
socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il y a présence
de parasites, il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du
magnétoscope afin de réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter
avec des bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et
causer des blessures. Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les
autres piles de ce type, elles pourraient dégager une matière toxique qui peut causer
des blessures corporelles si elles sont brûlées ou percées.
The RBRC seal
The RBRC seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used nickel-
metal hydride batteries into the trash or municipal waste, which may be
illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers
participating in the program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/
restrictions in your area. VTech’s involvement in this program is part of its commitment to
protecting our environment and conserving natural resources.
The RBRC seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Privacy of communications may not be ensured when using this
telephone.
To ensure safety of users, the FCC/ISEDC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply with
the FCC/ISEDC criteria. The handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts of the user’s body other than
the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label
on the back or bottom of this equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your
telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to a
single line and an RJ14 jack for two lines. See the installation instructions in the user’s
manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the US:
in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the
sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment must not be used with Party Lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone service provider or a qualified
installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Replacement to this telephone equipment can only
be made by the manufacturer or its authorized agents. For replacement procedures,
follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service
provider may temporarily discontinue your telephone service. The telephone service
provider is required to notify you before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You will be given the opportunity to
correct the problem and the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone service provider is required to notify
you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test
emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN
indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices
subject only to the requirement that the sum of the RENs of all the devices not exceed
five.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the
box. These instructions are intended for California Energy Commission (CEC) compliance
testing only. When the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all
handsets are plugged with charged batteries before proceeding.
2. While you press and hold /FIND HS, plug the telephone base power adapter back
to the power outlet.
3. After about 20 seconds, when the IN USE light starts flashing, release /FIND HS and
immediately press it again within two seconds.
When the phone successfully enters the CEC battery charging testing mode, all
handsets display To register HS, see manual..
When the phone fails to enter this mode, repeat steps 1 to 3 above.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, and then plug it
back in. Then the telephone base is powered up as normal.
2. Make sure the handset is out of the telephone base or charger and shows To register
HS, see manual..
3. Put the handset on the telephone base cradle.
4. The handset shows Registering.... Please wait and the IN USE light on the telephone
base turns on. The handset beeps and the IN USE light turns off when the registration
process completes.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the Consumer for
Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will
replace at VTech’s option, without charge, a Materially Defective Product. If we replace
the Product, we may use new or refurbished replacement parts. If we choose to replace
the Product, we may replace it with a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement
Products to you in working condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date
of purchase. If VTech replaces a Materially Defective Product under the terms of this
limited warranty, this limited warranty also applies to the replacement Product for a
period of either (a) 90 days from the date the replacement Product is shipped to you or
(b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion.
2. Product that has been subjected to contact with liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like; but then only to the extent
the damage was not caused by incorrectly securing the waterproof handset’s
protective elements, for example, failing to properly close a seal), or such
protective elements are damaged or missing (e.g. a cracked battery door), or
subjecting a Product to conditions beyond its stated specifications or limits (e.g. 30
minutes in 1 meter of fresh water).
3. Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech;
4. Product to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems;
5. Product to the extent that the problem is caused by use with non-VTech
accessories;
6. Product whose warranty/quality stickers, product serial number plates or
electronic serial numbers have been removed, altered or rendered illegible;
7. Product purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes);
8. Product returned without a valid proof of purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of customer controls, and installation
or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s
controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred
in the transport of the Product(s) to the service location. VTech will return replaced
Product under this limited warranty. Transportation, delivery or handling charges are
prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the Product failure
is not covered by this limited warranty, or proof of purchase does not meet the terms
of this limited warranty, VTech will notify you and will request that you authorize the
cost of replacement prior to any further replacement activity. You must pay for the cost
of replacement and return shipping costs for the replacement of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the
VTech service location along with a description of the malfunction or difficulty;
and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone
number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/provinces do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to use the
Product or other associated equipment, the cost of substitute equipment, and claims
by third parties) resulting from the use of this Product. Some states/provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase
Press
Press - OR -
Press - OR -
Answering system Need help?
Call Block
If you subscribe to caller ID service, you can set the telephone
to block unknown calls and certain undesired calls. The call
block list can store up to 150 entries.
Add a call block entry
HANDSET
Answerinsg sys
>Call block
>Block list
Calls w/o num
Review
>Add new entry
ENTER NUMBER
800-595-9511_
ENTER NAME
Mike Smiths_
Delete a call block list entry
Review the call
block list entries and
when the desired
entry displays on the
handset screen:
Block unknown calls
HANDSET
Answerinsg sys
>Call block
Block list
>Calls w/o num
CALLS W/O NUM
>Block
2Press / to scroll
to Call block, then
press SELECT.
3
Press SELECT
to select Block list.
4Press / to scroll
to Add new entry,
then press SELECT.
1Press MENU.
5Enter number
then press SELECT.6Enter name
then press SELECT.
1Press MENU.2Press / to scroll
to Call block,
then press SELECT.
3Press / to scroll
to Calls w/o num,
then press SELECT.
4
Press / to scroll
to Block, then
press SELECT.
Call block
CS5229-X (CA)
CS5229-X (US)
Press to turn on;
press again to turn off.
1
Press MENU.2Press / to scroll
to Answering sys,
then press SELECT.
3
Press / to scroll
to Ans sys setup,
then press SELECT.
4Press / to scroll
to # of rings,
then press SELECT.
Press / to scroll to
the desired number of
rings, then press SELECT.
5
Set voice language (For Canada version only)
The voice prompt language is preset to English. You can select English or French
to be used for all voice prompts.
1
Press MENU.
2 Press / to scroll to Settings, then press SELECT.
3 Press / to scroll to Voice language, then press SELECT.
4
Press / to scroll to English or Français, then press SELECT.
10:15PM 12/ 25
Mike Smith
595-9511
Press DELETE, then press
SELECT to confirm.
10:15 12/ 25
AM
10:15PM 12/ 25
Review a call block list entry
HANDSET
Answerinsg sys
>Call block
>Block list
Calls w/o num
>Review
Add new entry
Press MENU.
12Press / to scroll
to Call block,
then press SELECT.
3Press SELECT
to select Block list.
4Press SELECT
to select Review.
10:15PM 12/ 25
10:15PM 12/ 25
10:15PM 12/ 25
-
1
-
2
VTech CS5229-5 Mode d'emploi
- Catégorie
- Téléphones
- Taper
- Mode d'emploi
dans d''autres langues
- English: VTech CS5229-5 User guide