TP-LINK tp-link RM200 Tapo Robot Vacuum Manuel utilisateur

tp-link RM200 Tapo Robot Vacuum
TP-LINK
Marque
TP-LINK
Modèle
tp-link RM200 Tapo Robot Vacuum
Catégorie
Antennes réseau
Taper
Manuel utilisateur

Ce manuel convient également à

RM200 User Manual
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1） This device may not cause harmful interference.
2） This device must accept any interference received, including interference
that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
Warning: changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This Module complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Installation Notice to Host Product Manufacturer
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
The module is limited to installation in mobile application, a separate approval is required
for all other operating configurations, including portable configurations with respect to
§2.1093 and difference antenna configurations.
Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS
102 and compliance with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section
2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir
l'information canadienne sur l'exposition et la conformité de rf.
This radio transmitter (IC: 26583-RM200) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 26583-RM200) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci‐dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Antenna Information
Ant.
Brand
P/N
Antenna Type
Connector
Gain (dBi)
1
3101502753
Dipole
I-PEX
1.97
This device is intended only for OEM integrators under the following condition:
● The transmitter module may not be co‐located with any other transmitter or antenna.
As long as the condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end‐product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes:
● Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci‐dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
Note Importante
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co‐localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID ISED ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera
chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labelling
The final end product must be labelled in a visible area with the following:
“Contains certifified FCC ID: 2AXJ4RM200”.
“Contains certifified IC: 26583-RM200”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
Contient des IC: 26583-RM200
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur
du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.
1. Overview
The RM200 Wi-Fi module provides a highly-integrated and flexible platform for
developing and evaluating products and applications based on the RTL8723DS SoC.
The RM200 Wi-Fi module can be either used with development kit for software
development or incorporated into OEM products to enable rapid deployment of Wi-Fi
connected systems.
The module includes the following components:
RTL8723DS chip
An integrated Balun
Shield
2. Interface and pinout
Interface:
UART
SDIO
Power supply
Pinout:
3. Electric Feature
Power Supply
DC
3.3V0.5A
330mW
29mW
4. Mechanic Feature
Size: 12mm*12mm*2.9mm
5. Wireless Feature
WIFI
BLE
Modulation technology
DSSS,OFDM
GFSK
Operating Frequency
2412~2462MHz
2402~2480MHz
Transfer Rate
802.11b: 11/5.5/2/1 Mbps
802.11g:
54/48/36/24/18/12/9/6
Mbps
802.11n: up to 72.2 Mbps
1Mbps
Wireless Channel
ch1-ch11
Ch00-ch39
Transimit Power
19.96dBm(max)
6.27 dBm(max)
Antenna Type
Dipole antenna
Antenna Gain
1.97dbi
6. Physical and Environmental
Operating Temperature: 0℃～60℃
Storage Temperature: 5℃～40℃
Working Humidity: 20%～90% RH
7. Additional Description
The module will be installed inside another device. And the outside of the device into
which the module is installed will display a label referring to the enclosed module.
This exterior label will use the wording such as “Contains FCC ID: 2AXJ4RM200”, or
any other similar wording that expresses the same meaning.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

TP-LINK tp-link RM200 Tapo Robot Vacuum Manuel utilisateur

tp-link RM200 Tapo Robot Vacuum
TP-LINK
Marque
TP-LINK
Modèle
tp-link RM200 Tapo Robot Vacuum
Catégorie
Antennes réseau
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents