Traxxas TRX-4M K10 Mode d'emploi

Taper
Mode d'emploi
Covers Part #9883
Pro Scale® LED Light Kit Installation Instructions
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
HKC23079-R00 Rev 230810
Kit Contents:
LED headlights/tail lights harness assembly
Zip ties (6)
Tools required:
1.5mm hex wrench
Side cutters (to trim zip ties)
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
1. Remove zip ties (3).
1. Install the left and then right LED headlight assemblies (A).
2.
Route both LED tail light assemblies toward the rear of the body (B).
BODY DISASSEMBLY
LED LIGHT INSTALLATION
3. Remove the existing tail light housings.
2. Remove front LED headlight
retainers and light harness.
Stock LED
Headlight
Stock
LED Headlight
1.6x7mm
BCS
1.6x7mm
BCS
1.6x7mm
BCS
1.6x7mm
BCS
6x10mm
BCS
6x10mm
BCS
6x10mm
BCS
6x10mm
BCS
1.6x7mm
BCS
1.6x7mm
BCS
Tail Light
Housing
Tail Light
Housing
Right LED Headlight
Assembly
Left LED Headlight
Assembly
Left LED Tail Light
Assembly Right LED
Tail Light
Assembly
1.6x7mm
BCS
1.6x7mm
BCS
If you have questions or need technical assistance, call Traxxas at
1-888-TRAXXAS
(1-888-872-9927) (U.S. residents only)
Note: Retain and reuse hardware. Discard the parts or save for future use.
Note: Discard these parts and hardware or save for future use.
A
B
3. Install the right and then left LED tail light assemblies.
OPERATION
Mode Selection
The LED lights will turn on when the electronic control module (ECM) is powered on by plugging in the battery. Press and release the EZ-Set button on
the ECM to toggle through the different lighting modes. The chart below indicates how the lights will function in each mode:
WIRING DIAGRAM
BODY UNDERSIDE VIEW
Warranty Information
Traxxas electronic components are warranted to be free from defects in materials
and workmanship for a period of 30 days from the date of purchase.
Limitations: Any and all warranty coverage does not cover replacement of
parts and components damaged by abuse, neglect, improper or unreasonable
use, crash damage, water or excessive moisture, chemical damage, improper or
infrequent maintenance, accident, unauthorized alteration or modification or items
that are considered consumable. Traxxas will not pay for the cost of shipping or
transportation of a defective component to us.
WARRANTY
Traxxas Lifetime Electronics Warranty
After the expiration date of the warranty period, Traxxas will repair electronic
components for a flat rate. The covered repairs are limited to non-mechanical
components that have NOT been subjected to abuse, misuse, or neglect. Products
damaged by intentional abuse, misuse, or neglect may be subject to additional
charges. Traxxas liability, in no case, shall be greater than the actual purchase price
of this product. For replacement, product must be returned in brand new condition,
with packaging and itemized sales receipt.
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]
Use zip ties to secure all wiring to the body in the 5 locations shown.
To reset back to the default mode and settings, unplug the battery from the ECM and start over.
Mode Selection Action
1Headlights, daytime running lights, and tail lights on; brake lights on when braking; reverse lights on
when reversing Default
2Headlights o; daytime running lights and tail lights on; brake lights on when braking; reverse lights on
when reversing Press and release EZ-Set button on ECM once
3Headlights, daytime running lights, and tail lights o; brake lights on when braking; reverse lights on
when reversing Press and release EZ-Set button on ECM 2x
4Hazard lights on; headlights, daytime running lights, and tail lights o; brake lights on when braking;
reverse lights on when reversing Press and release EZ-Set button on ECM 3x
5 LED lights display (demo mode, sequence of all lighting) (truck will not drive in this mode) Press and release EZ-Set button on ECM 4x
  • Page 1 1
  • Page 2 2

Traxxas TRX-4M K10 Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues