Chief KTA1001B Guide d'installation

Catégorie
Accessoires pour écran plat
Taper
Guide d'installation

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Dual 220
Dual 320
Triple 220
Triple 320
Array Connector Accessory Kit
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KTA1001
KTA1001 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
Dual 320 Triple 320
Dual 220 Triple 220
Installation Instructions KTA1001
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
KTA1001 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm)
1/2" (12.7mm)
5/32"
A (1)
[array connecting bracket]
B (2)
1/4-20 x 1/2" C (2)
1/4-20 x 3/4" D (4)
1/4-20"
Installation Instructions KTA1001
5
INSTALLATION
Mount and Site Preparation
Mount Preparation
To prepare existing mount arrays for
connection:
1. Remove end lock from array rail ends to be joined using
5/32" hex key. (See Figure 1)
NOTE: Leave square nut in array rail after removing end lock.
Figure 1
To install the KTA1001:
1. Insert two square nuts (D) into each rail end. (See Figure 2)
2. Slide rails together until rail ends meet. (See Figure 2)
Figure 2
3. Place connecting bracket (A) against rails aligning holes in
connector bracket with square nuts installed during step 1.
(See Figure 3)
NOTE: The two center square nuts must align with holes in rail
ends.
4. Secure connector bracket outer mounting holes to array
rails using two 1/4-20 x 1/2" button head cap screws (B)
making sure each screw threads into a square nut (D). (See
Figure 3)
5. Secure connector bracket inner mounting holes to array
rails using two 1/4-20 x 3/4" button head cap screw (C)
making sure each screw threads into a square nut (D) and
through hole in array rail. (See Figure 3)
CAUTION: Center connector mounting screws must go
through square nut and hole in array rail to maintain mount
integrity.
Figure 3
Array rail connection is now complete. Refer to Installation
Instructions provided with mount or other accessory for
additional installation instructions if required.
End Lock
Square Nut
Array Rail
1
(D) x 2
(D) x 2
Array Rail
1
1
2
Array Rail
(A) (C) x 2
Array Rail
5
4
(B) x 2
KTA1001 Installation Instructions
6
Installation Instructions KTA1001
7
KTA1001 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002204 Rev00
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief KTA1001B Guide d'installation

Catégorie
Accessoires pour écran plat
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues