INSTALLATION INSTRUCTIONS
Shelf Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC-101/102/103
PAC-101/102/103 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory. The wall to which the accessory is being attached
may have a maximum drywall thickness of 5/8” (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to accessory does not exceed 20 lbs
(9.1 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
IMPORTANT ! :
The
accessory
is designed to be mounted to:
•PAC101 -a 2" x 4" wood stud wall, covered with drywall
with a maximum thickness of 5/8";
•PAC102 - a 1-1/2" NPT pipe
--SAVE THESE INSTRUCTIONS--
Installation Instructions PAC-101/102/103
3
DIMENSIONS
8
.
0
0
203.2
0.40
10.1
CLAMPS TO 2" OD PIPE MAX
251.9
355.6
9.92
14.00
3.50
88.9
36.0
1.42
1.25
31.8
PAC102
DIMENSIONS: INCHES
[MILLIMETERS]
PAC101
DIMENSIONS: INCHES
[MILLIMETERS]
PAC-101/102/103 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Installation Instructions PAC-101/102/103
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8"
#2
5/32"
(included)
7/16"
L (1) 6 ft length
A (1)
B2 (1)
(PAC102)
B1 (1)
(PAC101)
(PAC103)
C (1)
(PAC102)
[Shelf top]
D (1)
1/4-20 x 1/2" E (1)
1/4-20"
F (2)
1/4 x 2"
G (2)
1/4"
H (2)
1/4-20 x 3/4" J (2)
1/4" K (1)
5/32"
PAC101
PAC102
PAC102
PAC101
(PAC101, PAC102)
Hardware Bags
PAC-101/102/103 Installation Instructions
6
INSTALLATION
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware! Use only hardware provided by manufacturer.
PAC101 Shelf Base Installation
The PAC101 is designed to be installed into a wood stud.
To install the PAC101:
1. Place shelf base (B1) in desired mounting location.
2. Level shelf base. (See Figure 1)
3. Mark and drill two 1/8" pilot holes into center of stud.
4. Secure shelf base to wood stud using two 1/4" flat washers
(G) and two 1/4 x 2" hex head lag screws (F).(See Figure 1)
Figure 1
PAC-102 Shelf Base Installation
The PAC-102 is designed to be mounted onto a 1-1/2" NPT
steel pipe.
To install the PAC-102:
1. Place shelf base (B2) in desired mounting location on pole.
2. Align pole mount bracket (C) with shelf base (B2).
3. Secure pole mount bracket (C) to shelf base (B2) using two
1/4" flat washers (J) and two 1/4-20 x 3/4" button head cap
screws (H). (See Figure 2)
Figure 2
Attach Shelf to Shelf Base (PAC101, PAC102)
1. Align square mounting hole in shelf (A) with mounting hole
in top of shelf base (B1 or B2). (See Figure 3)
2. Secure shelf (A) to shelf base (B1 or B2) using one carriage
bolt (D) and one lock nut (E). (See Figure 3)
Figure 3
(F) x 2
(B1)
Wood Stud
4
1
(G) x 2
3
(H) x 2
(B2)
1-1/2" NPT Pole
(J) x 2
2
1
3
(C)
(A)
(E) x 1
(D) x 1
2
2
1
Installation Instructions PAC-101/102/103
7
PAC-103 Installation
To install the optional PAC-103 Strap:
1. Place equipment on shelf (A). (See Figure 4)
Figure 4
2. Thread PAC103 (L) through slots in shelf base (B1 or B2).
(See Figure 5)
Figure 5
3. Loop strap (L) over top of equipment and slide strap end into
clasp. (See Figure 6)
Figure 6
4. Pull strap (L) until tight around equipment and press clasp
closed to secure. (See Figure 7)
Figure 7
1
(A)
2
(B1 or B2) x1
(L)
3
(L)
4
(L)
PAC-101/102/103 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002901 Rev00
2017 Milestone AV Technologies
www.milestone.com
05/17
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PAC103 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PAC103 Installation guide
Documents connexes
-
Chief ERT-ST Guide d'installation
-
-
-
-
Chief FCA651B Guide d'installation
-
-
Chief PACCS1 Guide d'installation
-
-
-
Chief TA200 Guide d'installation