Modern Forms PD-35603L Magic Mode d'emploi
- Taper
- Mode d'emploi
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
356 - LED Pendant
PD-35603L
HARDWARE
A1 B1 C1 D1 E1
Wire Connector
Qty: 3 pcs
Junction Box Screw
Qty: 2 pcs + 1 Extra
Mounting Screw
Qty: 1 Extra
Wood Screw
Qty: 2 pcs + 1 Extra
Plastic Anchor
Qty: 2 pcs + 1 Extra
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
356 - LED Pendant
PD-35603L
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C1) from the xture.
4. Drill a hole in the ceiling aligned with the key hole located in the mounting back plate, insert the plastic anchor (E1).
5. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
6. Connect the driver input wires with junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
*Requires driver to be recessed within the junction box.
MOUNTING THE FIXTURE (Fig. 1)
7. Secure mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using the wood screw (D1). The side of the mounting plate
marked “GND” must face out.
8. Place the xture over the mounting plate and secure it with mounting screws (C1).
9. Thread the noodle glass onto the lamp body.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
FIG.1 Back Plate Dimensions
35 3/8” 27 5/8”
4 1/8”
1 3/8”
1 3/4”
A1
Wire Connector
Mounting Backplate
B1
E1
D1
C1
Junction Box Screw
Plastic Anchor
Wood Screw
Mounting Screw
Ground Wire
Junction Box
Driver
Cable Gripper
Cylinder Lamp Body
Cylinder Noodle Glass
1 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2016
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
.BHJD - LED Pendant
PD-35605L
HARDWARE
AB C D E
Wire Connector
Qty: 3 pcs
Junction Box Screw
Qty: 2 pcs + 1 Extra
Mounting Screw
Qty: 1 Extra
Wood Screw
Qty: 2 pcs + 1 Extra
Plastic Anchor
Qty: 2 pcs + 1 Extra
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
Wire Connector
Qty: 3 pcs + 1 Extra
7EAC112201
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x9/16 SS
Mounting Screw
Qty: 1 Extra
7MPF0412S1
5/32”-32 x 1/2
Nickel Plating
Wood Screw
Qty: 2 pcs + 1 Extra
7MPF2204J2
Ø4x22mm
Nickel Plating
Plastic Anchor
Qty: 2 pcs + 1 Extra
7TDD082401
2 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2016
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
.BHJD - LED Pendant
PD-35605L
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C1) from the xture.
4. Drill a hole in the ceiling aligned with the key hole located in the mounting back plate, insert the plastic anchor (E1).
5. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
6. Connect the driver input wires with junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
*Requires driver to be recessed within the junction box.
MOUNTING THE FIXTURE (Fig. 1)
7. Secure mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using the wood screw (D1). The side of the mounting plate
marked “GND” must face out.
8. Place the xture over the mounting plate and secure it with mounting screws (C1).
9. Thread the noodle glass onto the lamp body.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
FIG.1 Back Plate Dimensions
35 3/8” 27 5/8”
4 1/8”
1 3/8”
1 3/4”
A
Wire Connector
Mounting Backplate
B
E
D
C
Junction Box Screw
Plastic Anchor
Wood Screw
Mounting Screw
Cable Gripper
Cylinder Lamp Body
Cylinder Noodle Glass
Junction Box
Driver
Ground Wire
Cable-Gripper
Push Up
°µ¾ÀÉ°ÌÑÀ
ÒÓ
ÔÓ
ÕÌÓÕ
8. Secure mounting plate to the junction box using junction box screws(B1),
fasten it to the wall using the wood screw(D1).The side of the mounting plate
marked”GND” must face out.
9. Place the xture over the mounting plate and secure it with mounting screws(C1).
10. Thread the piastra glass onto the lamp body.
!"#$%&#'()$*#"(+),-.
piastra glass
3
Phone (800) 526.2588
Fax (800) 526.2585
!"#!$%&!$'()$)*#$)'+$
44 Harbor Park Drive
Port Washington, NY 11050
+$!,'()$)*#$)'+$
1600 Distribution Ct
Lithia Springs, GA 30122
-$'()$)*#$)'+$''
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
PD-35605L
!"#$
Driver
,
nput
2XW
put
Black
- Hot
White -
Neutral
Driver
,
nput
Out
SXW
Black
- Hot
White -
Neutral
Black
- Hot
White -
Neutral
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
MAGIC - LED Chandelier
PD-35623L
Wire Connector
Qty: 3 pcs + 1 Extra
7EAC112201
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8-32x9/16 SS
Mounting Screw
Qty: 1 Extra
7MPF0412C1
5/32"-32x1/2
Nickel Plating
Wood Screw
Qty: 8 pcs + 1 Extra
7MPF2204J2
Ø4x22mm
Nickel Plating
Plastic Anchor
Qty: 8 pcs + 1 Extra
7TDD082401
A1 B1 C1 D1 E1
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (C1) from the xture.
4. Install the mounting back plate to the junction box using junction box screws (B1)
5. Mark the eight wood screw mounting holes on the ceiling, remove mounting back plate, drill holes and insert the eight plastic anchors (E1)
6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
7. Connect the driver input wires with supply wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
8. Install mounting plate back to the junction box using junction box
screws (B1), fasten it to the ceiling using the eight wood screws (D1).
The side of the mounting plate marked “GND” must face out.
9. Hook the two safety cable to the mounting plate.
10. Push the xture onto the mounting back plate, and secure it with
mounting screws (C1) .
11. Thread the noodle glass onto the glass holder.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Plastic Anchor
Junction Box Screw
Wood Screw
Mounting Screw
Cable Gripper
Driver
Glass Holder
Cylinder 1JBTUSB Glass
(RPL-GLA-12620)
Safety Cable
Mounting Back Plate
Junction Box
Ground Wire
41 3/8"
11 3/4"
7 1/8"11"
35 3/8"
27 7/8"
1 3/4"
1 3/8"
Back Plate Dimensions
Fixture
E1
B1
D1
C1
FIG. 1 Wire Connector B1
INSTALLATION INSTRUCTION
MAGIC - LED Chandelier
PD-35623L
Cable
gripper Push up
Instruction: Adjust the xture
wire length by pushing the
cable gripper on the canopy
and pulling the wire as desired.
°µ¾ÀÉ°ÌÑÀÒ
ÓÔÓ
ÕÌÓÕ
9. Secure mounting plate to the junction box using junction box screws(B1),fasten it to the wall using the wood screw(D1).The side of the mounting
plate marked”GND” must face out.
10. Hook the two safety cords to the mounting plate.
11. Push the xture onto the mounting back plate and rotate the xture until it is docked in position,secure it with mounting screws (C1)
12. Thread the 1JBTUSBglass onto the lamp body.
!"#$%&#'()$*#"(+),-.
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
MAGIC - LED Chandelier
PD-35623L
"
Recommended Length
32”
21”
32”
13”
11”
26”
20”
29”
18”
33”
13”
Bottom
28”
15”
25” 34”
20”
17” 23”
31”
14”
29”
13”
18”
21”
21”
13”
26”
11”
29”
20”
18”
33”
13”
28”
15”
20”
18”
25”
13”
20”
34”
17”
29”
14”
23”
31”
Phone (800) 526.2588
Fax (800) 526.2585
!"#!$%&!$'()$)*#$)'+$
44 Harbor Park Drive
Port Washington, NY 11050
+$!,'()$)*#$)'+$
1600 Distribution Ct
Lithia Springs, GA 30122
-$'()$)*#$)'+$''
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
PD-35623L
'ULYHU
,
QSXW
2XW
SXW
%ODFN
+RW
:KLWH
1HXWUDO
'ULYHU
,
QSXW
2XW
SXW
%ODFN
+RW
:KLWH
1HXWUDO
%ODFN
+RW
:KLWH
1HXWUDO
'ULYHU
,
QSXW
2XW
SXW
'ULYHU
,
QSXW
2XW
SXW
%ODFN
+RW
:KLWH
1HXWUDO
%ODFN
+RW
:KLWH
1HXWUDO
'ULYHU
,
QSXW
2XW
SXW
%ODFN
+RW
:KLWH
1HXWUDO
'ULYHU
,
QSXW
2XW
SXW
%ODFN
+RW
:KLWH
1HXWUDO
!""
!"#
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Modern Forms PD-35603L Magic Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-15604 Acid Mode d'emploi
-
-
-
-
-
-
-
-
-