MAC TOOLS N256182 Manuel utilisateur

Marque: MAC TOOLS

Modèle: N256182

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Ce manuel convient également à

BDP050

BDP050

Operation and Maintenance Manual

Before operating this tool, all operators

should study this manual to understand

and follow the safety warnings and

instructions. Keep these instructions with

the tool for future reference. If you have

any questions, contact your MAC TOOLS

representative or distributor.

1/2" BDP050

WARNING

Part No. N256182

20V Max

Cordless Drill

English

Contact your MAC TOOLS representative or distributor with any

questions concerning the tool and its use.

MAC TOOLS

505 North Cleveland Ave., Suite 200, Westerville, Ohio 43082

1-877-MAC-TOOLS

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another battery

pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

English

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known

to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do

this type of work. To reduce your exposure to these chemicals: work

in a well ventilated area, and work with approved safety equipment,

such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on

the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropriate

for the dust exposure. Direct particles away from face and body.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety Rules for Drill/Drivers

• Wear ear protectors with impact drills. Exposure to noise can

cause hearing loss.

• Use auxiliary handles supplied with the tool. Loss of control

can cause personal injury.

• Hold power tool by insulated gripping surfaces when

performing an operation where the fastener may contact

hidden wiring. Fasteners contacting a “live” wire may make

exposed metal parts of the power tool “live” and could give the

operator an electric shock.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body is unstable and may lead to loss of control.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

English

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

• Charge the battery packs only in MAC TOOLS

™

chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 ˚F (40 ˚C)

(such as outside sheds or metal buildings in summer).

WARNING: Fire hazard. Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged, do not insert

into charger. Do not crush, drop or damage battery pack. Do not use a

battery pack or charger that has received a sharp blow, been dropped,

run over or damaged in any way (i.e., pierced with a nail, hit with a

hammer, stepped on). Damaged battery packs should be returned to

service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so

that metal objects can contact exposed battery terminals.

For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting individual

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may contribute

to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ............. volts

Hz ........... hertz

min .........minutes

......direct current

...........Class I Construction

(grounded)

...........Class II Construction

(double insulated)

…/min .....per minute

IPM ........ impacts per minute

A .......... amperes

W ......... watts

....... alternating current

....... alternating or direct

current

o ........ no load speed

........ earthing terminal

......... safety alert symbol

RPM .... revolutions per minute

BPM .... beats per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include catalog

number and voltage.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below. Then

follow charging procedures outlined.

English

RBRC™, in cooperation with MAC TOOLS and other battery

users, has established programs in the United States and Canada

to facilitate the collection of spent nickel cadmium, nickel metal

hydride or lithium ion batteries. Help protect our environment and

conserve natural resources by returning the spent nickel cadmium,

nickel metal hydride or lithium ion batteries to an authorized

MAC TOOLS

™

service center or to your local retailer for recycling.

You may also contact your local recycling center for information on

where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instruc tions for battery chargers.

• Before using charger, read all instructions and cautionary markings

on charger, battery pack, and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

MAC TOOLS

™

rechargeable batteries. Other types of batteries may

burst causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil, or any buildup of metallic

particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the

cavity. Unplug charger before attempting to clean.

batteries, make sure that the battery terminals are protected and well

insulated from materials that could contact them and cause a short

circuit.

NOTE: Do not store the battery packs in a tool with the trigger

switch locked on. Never tape the trigger switch in the ON position.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs)

indicate that the costs to recycle these batteries

(or battery packs) at the end of their useful life have

already been paid by MAC TOOLS. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium ion

batteries in the trash or municipal solid waste stream and the RBRC

program provides an environmentally conscious alternative.

English

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging MAC TOOLS

™

rechargeable batteries. Any other

uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

English

a fast rate. If this occurs, re-insert battery pack into the charger. If the

problem persists, try a different battery pack to determine if the charger

is OK. If the new pack charges correctly, then the original pack is

defective and should be returned to a service center or other collection

site for recycling. If the new battery pack elicits the same trouble

indication as the original, have the charger tested at an authorized

service center.

HOT/COLD PACK DELAY

Some chargers have a Hot/Cold Pack Delay feature: when the charger

detects a battery that is hot, it automatically starts a Hot Pack Delay,

suspending charging until the battery has cooled. After the battery

has cooled, the charger automatically switches to the Pack Charging

mode. This feature ensures maximum battery life. The red light flashes

long, then short while in the Hot/Cold Pack Delay mode.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 ˚F and

75 ˚F (18 –24 ˚C). DO NOT charge the battery pack in an air

temperature below +40 ˚F (+4.5 ˚C), or above +105 ˚F (+40.5 ˚C).

This is important and will prevent serious damage to the battery

pack.

Chargers

Your tool uses a MAC TOOLS

™

charger. Be sure to read all safety

instructions before using your charger.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate outlet before inserting battery

pack.

2. Insert the battery pack (H) into the charger, as shown in Figure 1,

making sure the pack is fully seated in charger. The red (charging)

light will blink continuously indicating that the charging process

has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

this

time

left

the

cha

FIG. 1

Charge Indicators

Some chargers are designed to detect certain problems that can arise

with battery packs. Problems are indicated by the red light flashing at

English

there is no battery pack in the cavity. Unplug charger before

attempting to clean.

7. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

WARNING: Never attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks, return to a

service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

COMPONENTS (Fig. 2)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65 ˚F–75 ˚F

(18–24 ˚C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

English

INTENDED USE

This drill/driver is designed for light fastening and drilling applications.

DO NOT use under wet conditions or in presence of flammable liquids

or gases.

This drill/driver is a professional power tool. DO NOT let children come

into contact with the tool. Supervision is required when inexperienced

operators use this tool.

Variable Speed Trigger Switch (Fig. 2)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off,

release the trigger switch. Your tool is equipped with a brake. The

chuck will stop when the trigger switch is fully released. The variable

speed switch enables you to select the best speed for a particular

application. The more you squeeze the trigger, the faster the tool will

operate. For maximum tool life, use variable speed only for starting

holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended.

It may damage the switch and should be avoided.

Forward/Reverse Control Button (Fig. 2)

A forward/reverse control button (B) determines the direction of the

tool and also serves as a lock off button. To select forward rotation,

release the trigger switch and depress the forward/reverse control

button on the right side of the tool. To select reverse, depress the

forward/reverse control button on the left side of the tool. The center

position of the control button locks the tool in the OFF position. When

changing the position of the control button, be sure the trigger is

released.

NOTE: The first time the tool is run after changing the direction of

rotation, you may hear a click on start up. This is normal and does

not indicate a problem.

FIG. 2

English

off and permit to stop. Slide the gear shifter back (away from chuck).

NOTE: Do not change gears when the tool is running. If you are

having trouble changing gears, make sure that the dual range gear

shifter is either completely pushed forward or completely pushed back.

OPERATION

WARNING: To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position or

turn tool off and disconnect battery pack before making any

adjustments or removing/installing attachments or accessories.

FIG. 4

Installing and Removing the Battery Pack

(Fig. 4)

NOTE: Make sure your battery pack is fully charged.

To install the battery pack (H) into the tool handle, align the battery

with the rails inside the tool’s handle and slide it into the handle until

the battery pack is firmly seated in the tool and ensure that it does not

disengage. To remove the battery pack from the tool, press the release

button (G) and firmly pull the battery pack out of the tool handle. Insert

it into the charger as described in the charger section of this manual.

Worklight (Fig. 2)

There is a worklight (C) located under the torque adjustment collar

(D). The worklight is activated when the trigger switch is depressed,

and will automatically turn off 20 seconds after the trigger switch is

released. If the trigger switch remains depressed, the worklight will

remain on.

Torque Adjustment Collar (Fig. 3)

FIG. 3

The torque adjustment collar (D) is clearly

marked with numbers and a drill bit symbol.

The collar should be rotated until the desired

setting is located at the top of the tool.

Locators are provided in the collar to eliminate

the guess work when selecting fastening

torque. The higher the number on the collar,

the higher the torque and the larger the

fastener which can be driven. To lock the

clutch for drilling operations, move to the drill

bit position.

NOTE: When using the drill/driver for drilling

holes, be sure that the torque adjusting collar

is set so the figure of the drill is aligned with

the center line on the top of the tool. Failure

to do this will allow the clutch to slip while

attempting to drill.

Dual Range Gearing (Fig. 3)

The dual range feature of your driver/drill allows you to shift gears for

greater versatility.To select the low speed, high torque setting, turn the

tool off and permit to stop. Slide the gear shifter (E) forward (towards

the chuck). To select the high speed, low torque setting, turn the tool

English

FIG. 5

Keyless Single

Sleeve Chuck

(Fig. 5)

Your tool features a keyless

chuck with one rotating sleeve

for one-handed operation of the

chuck. To insert a drill bit or other

accessory, follow these steps.

1. Lock the trigger in the

OFF position as previously

described.

2. Grasp the black sleeve of

the chuck with one hand

and use the other hand to secure the tool. Rotate the sleeve

counterclockwise far enough to accept the desired accessory.

3. Insert the accessory about 3/4” (19 mm) into the chuck and

tighten securely by rotating the chuck sleeve clockwise with one

hand while holding the tool with the other. Your tool is equipped

with an automatic spindle lock mechanism. This allows you to

open and close the chuck with one hand.

To release the accessory, repeat step 2 above.

WARNING: Do not attempt to tighten drill bits (or any other

accessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may result. Always

lock off trigger switch and disconnect tool from power source when

changing accessories.

Be sure to tighten chuck with one hand on the chuck sleeve and one

hand holding the tool for maximum tightness.

CHUCK REMOVAL (FIG. 6)

Turn the adjustment collar (D) to the “drill” position and gear shifter (E)

to position 1 (low speed). Tighten the chuck around the shorter end

of a hex key (not supplied) of 1/4” (6.4 mm) or greater size. Using a

wooden mallet or similar object, strike the longer end in the clockwise

direction, as shown. This will loosen the screw inside the chuck.

Open chuck jaws fully, insert Torx screwdriver into front of chuck

between jaws to engage screw head. Remove screw by turning

clockwise (left-hand-thread). Place hex key in chuck and tighten, as

shown in Figure 6. Using a wooden mallet or similar object, strike key

sharply in the counterclockwise direction. This will loosen the chuck so

that it can be unscrewed by hand.

FIG. 6 FIG. 7

English

WARNING: To reduce the risk of personal injury, ALWAYS

ensure workpiece is anchored or clamped firmly. If drilling thin material,

use a wood “back-up” block to prevent damage to the material.Turn

the collar (D) to the drill bit symbol for drilling. Select the desired speed/

torque range using the gear shifter (E) to match the speed and torque

to the planned operation.

1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits,

or hole saws. For METAL, use high-speed steel (HSS) twist drill

bits or hole saws.

2. Always apply pressure in a straight line with the bit. Use enough

pressure to keep drill biting, but do not push hard enough to stall

the motor or deflect the bit.

3. Hold tool firmly with both hands to control the twisting action of

the drill.

WARNING: The drill may stall if overloaded causing a sudden twist.

Always expect the stall. Grip the drill firmly with both hands to control

the twisting action and avoid injury.

4. IF DRILL STALLS, it is usually because it is being overloaded or

improperly used. RELEASE TRIGGER IMMEDIATELY, remove

drill bit from work, and determine cause of stalling. DO NOT

CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START

A STALLED DRILL — THIS CAN DAMAGE THE DRILL.

5. To minimize stalling or breaking through the material, reduce

pressure on drill and ease the bit through the last fractional part

of the hole.

6. Keep the motor running when pulling the bit back out of a drilled

hole. This will help prevent jamming.

7. With variable speed drills there is no need to center punch

the point to be drilled. Use a slow speed to start the hole and

accelerate by squeezing the trigger harder when the hole is deep

enough to drill without the bit skipping out.

CHUCK INSTALLATION (FIG. 7)

Screw the chuck on by hand as far as it will go and insert screw (left-

hand thread). Tighten screw securely. Tighten the chuck around the

shorter end of a 1/4” (6.4 mm) or larger hex key (not supplied) strike

the longer end in the clockwise direction with a wooden mallet, as

shown. Tighten the screw once again by turning in a counterclockwise

direction.

WARNING: To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position

or turn the tool off and disconnect battery pack before

making any adjustments or removing/installing attachments

or accessories.

Drill Operation (Fig. 2)

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments

or accessories.

FIG. 8

Proper Hand Position

(Fig. 2, 8)

WARNING: To reduce the risk of

serious personal, injury, ALWAYS

use proper hand position as shown.

WARNING: Hold tool firmly with

both hands to control the twisting

action of the drill. If model is not

equipped with side handle, grip drill

with one hand on the handle (I) and

one hand on the battery pack (H).

English

Operation as a Screwdriver (Fig. 2)

Select the desired speed/torque range using the dual range gear shifter

(E) on the top of tool to match the speed and torque to the planned

operation. Insert the desired fastener accessory into the chuck (F) as

you would any drill bit. Make a few practice runs in scrap or unseen

areas to determine the proper position of the clutch collar (D). Always

start with lower torque settings, then advance to higher torque settings

to avoid damage to the workpiece or fastner.

MAXIMUM RECOMMENDED CAPACITIES

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, place

the forward/reverse button in the lock-off position or turn tool off and

disconnect battery pack before making any adjustments or removing/

installing attachments or accessories.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by

MAC TOOLS, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only MAC TOOLS-recommended accessories should be used

with this product.

Recommended accessories for use with your tool are available

at extra cost from your local dealer or authorized service center.

If you need assistance in locating any accessory, please contact

MAC TOOLS, 505 North Cleveland Ave., Suite 200, Westerville, Ohio

English

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your MAC

TOOLS

™

Power Tool for any reason, you can return it within 90 days

from the date of purchase with a receipt for a full refund – no questions

asked.

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country specific

warranty information contained either in the packaging, call the local

company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-877-MAC TOOLS

(1-877-622-8665) for a free replacement.

43082, call 1-877-MAC-TOOLS (1-877-622-8665) or visit our website

www.mactools.com.

Repairs

The charger and battery pack are not serviceable. There are no

serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement)

should be performed by a MAC TOOLS

™

factory service center, a

MAC TOOLS

™

authorized service center or other qualified service

personnel. Always use identical replacement parts.

Three Year Limited Warranty

MAC TOOLS will repair, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase.

This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.mactools.com or call 1-877-MAC TOOLS

(1-877-622-8665). This warranty does not apply to accessories or

damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

In addition to the warranty, MAC TOOLS

™

tools are covered by our:

1 YEAR FREE SERVICE

MAC TOOLS will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON MAC TOOLS

™

BATTERY PACKS

MB120 AND MB201

3 YEARS FREE SERVICE ON MAC TOOLS

™

BATTERY PACKS

MB200

Français

Consignes générales de sécurité relatives

aux outils électriques

AVERTISSEMENT ! Lire toutes les instructions et toutes

les consignes de sécurité. Tout manquement aux

avertissements et consignes pose des risques de décharges

électriques, d’incendie et/ou de blessures graves.

CONSERVER TOUTES CES DIRECTIVES ET

CONSIGNES À TITRE DE RÉFÉRENCE

Le terme « outil électrique » dans ces avertissements concerne votre

outil électrique alimenté sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ - AIRE DE TRAVAIL

a) Maintenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner un outil électrique en milieu

déflagrant, en présence, par exemple, de poussières, gaz

ou liquides inflammables. Les outils électriques peuvent

produire des étincelles qui pourraient enflammer toute émanation

ou poussière ambiante.

c) Tenir les enfants, ou toute autre personne, à l’écart

pendant l’utilisation d’un outil électrique. Toute distraction

pourrait faire perdre la maîtrise de l’appareil.

2) SÉCURITÉ – ÉLECTRICITÉ

a) La fiche électrique de l’outil doit correspondre à celle de la

prise murale. Ne jamais modifier la fiche en aucune façon.

Ne pas utiliser un adaptateur avec un outil électrique

mis à la terre. L’utilisation de fiches d’origine et de prises

appropriées réduira les risques de choc électrique.

b) Éviter tout contact corporel avec des éléments mis

à la terre comme tuyaux, radiateurs, cuisinières ou

Pour toute question relative à cet outil et à son utilisation, veuillez

contacter un représentant

MAC TOOLS ou l’un de ses distributeurs.

MAC TOOLS

505 North Cleveland Ave., Suite 200, Westerville, Ohio 43082

1-877-MAC-TOOLS

AVERTISSEMENT : pour réduire tout risque de dommages corporels,

lire le manuel de l’utilisateur.

Français

l’interrupteur est en position d’arrêt avant de brancher

l’outil et/ou de le connecter à un bloc-piles, et avant de

le saisir ou de le transporter. Transporter un outil le doigt

sur l’interrupteur, ou alimenter un outil électrique alors que

l’interrupteur est en position de marche, invite les accidents.

d) Retirer toute clé de réglage avant de démarrer l’outil.

Une clé laissée sur une pièce rotative d’un outil électrique pose

des risques de dommages corporels.

e) Ne pas effectuer de travaux hors de portée. Les pieds

doivent rester bien ancrés au sol pour permettre de

maintenir son équilibre en permanence. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) Porter des vêtements appropriés. Ne pas porter de

vêtements amples ni de bijoux. Maintenir cheveux,

vêtements et gants éloignés des pièces mobiles. Les

vêtements amples, bijoux ou cheveux longs pourraient s’y faire

prendre.

g) Lorsqu’un dispositif de connexion à un système de

dépoussiérage ou d’élimination est fourni, s’assurer

qu’il est connecté et utilisé correctement. L’utilisation

d’aspirateurs peut réduire les risques engendrés par les

poussières.

4) UTILISATION ET ENTRETIEN DES OUTILS ÉLECTRIQUES

a) Ne pas forcer un outil électrique. Utiliser l’outil approprié

au travail en cours. L’outil approprié effectuera un meilleur

travail, de façon plus sûre et à la vitesse pour laquelle il a été

conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est

défectueux. Tout appareil dont l’interrupteur est défectueux est

dangereux et doit être réparé.

c) Débrancher la fiche du secteur et/ou le bloc-piles de l’outil

électrique avant de faire tout réglage ou changement

réfrigérateurs. Les risques de choc électrique augmentent

lorsque le corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. Toute pénétration d’un outil électrique par un liquide

augmente les risques de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher

un outil électrique. Protéger le cordon de la chaleur, de

l’huile, d’arêtes coupantes ou de pièces mobiles. Les

cordons endommagés ou emmêlés augmentent les risques de

chocs électriques.

e) Pour utiliser un outil électrique à l’extérieur, utiliser une

rallonge conçue à cet effet. L’utilisation d’une rallonge

conçue pour l’extérieur réduit les risques de chocs électriques.

f) Si l’utilisation d’un outil électrique en milieu humide est

inévitable, utiliser une alimentation protégée par un

disjoncteur de fuites à la terre (DDFT). L’utilisation d’un

DDFT réduit les risques de chocs électriques.

3) SÉCURITÉ PERSONNELLE

a) Rester constamment vigilant et faire preuve de jugement

pendant l’utilisation d’un outil électrique. Ne pas utiliser

d’outil électrique en cas de fatigue ou sous l’influence

de drogues, d’alcool ou de médicaments. Tout moment

d’inattention pendant l’utilisation d’un outil électrique pose des

risques de blessure grave.

b) Utiliser un équipement individuel de protection. Porter

systématiquement une protection oculaire. Le fait de porter

un équipement de protection tel que masque antipoussières,

chaussures antidérapantes, casque de sécurité ou protection

auditive lorsque la situation le requiert, réduira les risques de

dommages corporels.

c) Prévenir tout démarrage accidentel. S’assurer que

Français

c) Après utilisation, ranger le bloc-piles à l’écart de tout

objet métallique comme trombones, pièces de monnaie,

clés, clous, vis ou autres petits objets susceptibles de

conduire l’électricité entre les bornes. Court-circuiter les

bornes comporte des risques de brûlures ou d’incendie.

d) Se prémunir de tout contact avec le liquide que le bloc-piles

pourrait perdre lorsque sujet à des conditions extrêmes.

En cas de contact accidentel, rincer abondamment à

l’eau claire. En cas de contact oculaire, consulter aussi

un médecin. Le liquide perdu par le bloc-piles peut causer

irritations ou brûlures.

6) MAINTENANCE

a) Faire assurer la maintenance de votre outil électrique par

un réparateur qualifié en n’utilisant que des pièces de

rechange identiques. Cela permettra d’assurer l’intégrité de

l’outil électrique et la sécurité de l’utilisateur.

Règles de sécurité propres aux

perceuses/visseuses

• Porter une protection auditive lors du perçage à percussion.

Le bruit en émanant pourrait occasionner une perte de l’acuité

auditive.

• Utiliser les poignées auxiliaires fournies avec l’outil. Une

perte de contrôle de l’outil pourrait occasionner des dommages

corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet

pendant toute utilisation où l’attache pourrait entrer en

contact avec des fils électriques cachés. Tout contact par ces

attaches avec un fil sous tension mettra les parties métalliques

exposées de l’outil sous tension et électrocutera l’utilisateur.

• Utiliser des serre-joints ou tout autre moyen pour fixer et

immobiliser le matériau sur une surface stable. Tenir la pièce

d’accessoire, ou avant de ranger ce dernier. Ces mesures

préventives réduisent les risques de démarrage accidentel de

l’appareil.

d) Après utilisation, ranger les outils électriques hors de la

portée des enfants, et ne permettre à aucune personne

n’étant pas familière avec un outil électrique (ou son

manuel d’instruction) d’utiliser ce dernier. Les outils

peuvent être dangereux entre les mains des novices.

e) Entretenir les outils électriques. Vérifier les pièces

mobiles pour s’assurer qu’elles sont bien alignées et

tournent librement, qu’elles sont en bon état et ne sont

affectées d’aucune condition susceptible de nuire au

bon fonctionnement de l’outil. En cas de dommage, faire

réparer l’outil électrique avant toute nouvelle réutilisation.

Bien des accidents sont causés par des outils mal entretenus.

f) Maintenir les lames bien affutées et propres. Les outils de

coupe bien entretenus et affûtés sont moins susceptibles de se

coincer et sont plus faciles à contrôler.

g) Utiliser un outil électrique, ses accessoires, mèches,

etc., conformément aux présentes directives en tenant

compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que

celle pour laquelle il a été conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DES OUTILS À PILES

a) Les recharger seulement avec le chargeur spécifié par

le fabricant. Un chargeur propre à un type de bloc-piles peut

créer des risques d’incendie lorsqu’utilisé avec d’autres blocs-

piles.

b) Utiliser les outils électriques uniquement avec les blocs-

piles spécialement conçus à cet effet. L’utilisation de tout

autre bloc-piles comporte des risques de dommages corporels

et d’incendie.

Français

et nettoyer à l’eau savonneuse les parties du corps exposées.

Le fait de laisser la poussière pénétrer dans la bouche, les yeux ou la

peau peut favoriser l’absorption de produits chimiques dangereux.

AVERTISSEMENT : cet outil peut produire et/ou répandre de

la poussière susceptible de causer des dommages sérieux et

permanents au système respiratoire. Utiliser systématiquement un

appareil de protection des voies respiratoires homologué par NIOSH

ou OSHA. Diriger les particules dans le sens opposé au visage et au

corps.

AVERTISSEMENT : pendant l’utilisation, porter

systématiquement une protection auditive individuelle

adéquate homologuée ANSI S12.6 (S3.19). Sous certaines

conditions et suivant la durée d’utilisation, le bruit émanant de ce

produit pourrait contribuer à une perte de l’acuité auditive.

ATTENTION : après utilisation, ranger l’outil sur son côté,

sur une surface stable, là où il ne pourra ni faire trébucher ni

faire chuter quelqu’un. Certains outils équipés d’un large bloc-piles

peuvent tenir à la verticale sur celui-ci, mais manquent alors de stabilité.

à la main ou contre son corps offre une stabilité insuffisante qui

pourrait vous en faire perdre le contrôle.

• Prendre des précautions à proximité des évents, car ils

cachent des pièces mobiles. Les vêtements amples, bijoux ou

cheveux longs pourraient s’y faire prendre.

AVERTISSEMENT : porter SYSTÉMATIQUEMENT des lunettes

de protection. Les lunettes courantes NE sont PAS des lunettes de

protection. Utiliser aussi un masque antipoussières si la découpe

doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN

ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ :

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT : certains outils électriques, tels que les

ponceuses, les scies, les meules, les perceuses ou autres outils

de construction peuvent produire de la poussière contenant des

produits chimiques susceptibles d’entraîner le cancer, des anomalies

congénitales ou pouvant être nocifs pour le système reproducteur.

Parmi ces produits chimiques, on retrouve :

• le plomb dans les peintures à base de plomb;

• la silice cristallisée dans les briques et le ciment ou autres

produits de maçonnerie; et

• l’arsenic et le chrome dans le bois ayant subi un traitement

chimique (ACC).

Le risque associé à de telles expositions varie selon la fréquence à

laquelle on effectue ces travaux. Pour réduire toute exposition à ces

produits, travailler dans un endroit bien aéré, en utilisant du matériel

de sécurité homologué, tel un masque antipoussières spécialement

conçu pour filtrer les particules microscopiques.

• Limiter toute exposition prolongée aux poussières provenant

du ponçage, sciage, meulage, perçage ou toute autre

activité de construction. Porter des vêtements de protection

La page charge ...

MAC TOOLS N256182 Manuel utilisateur

Marque: MAC TOOLS

Modèle: N256182

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Ce manuel convient également à

BDP050

Télécharger le PDF

rapport

dans d''autres langues

English: MAC TOOLS N256182 User manual
español: MAC TOOLS N256182 Manual de usuario

MAC TOOLS N256182 Manuel utilisateur

Ce manuel convient également à

MAC TOOLS N256182 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents