sunjoe SPX3000-XT1 Le manuel du propriétaire

SAVE THESE INSTRUCTIONS

1

EN

Model SPX3000-XT1 Form No. SJ-SPX3000-XT1-880E-MR2

R

OPERATOR’S MANUAL

13A ELECTRIC PRESSURE WASHER

Original instructions.

A Division of Snow Joe, LLC

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in death or serious injury.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in death or serious injury.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the pressure washer, basic

safety precautions should always be followed to reduce the

risk of re, electric shock, and personal injury. These include:

• Know your product – Know how to stop the machine and

bleed pressure quickly. Thoroughly familiarize yourself with

the controls.

• Keep bystanders away – All visitors and pets should be

kept a safe distance away from the work area.

• Use the right product – Do not use this machine for any

job except that for which it is intended.

• Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

• mCAUTION! – Exercise caution to avoid slipping or falling.

Wear protective footwear that will protect your feet and

improve your footing on slippery surfaces.

• Stay alert – Watch what you are doing. Use common

sense. Do not operate the pressure washer when you are

tired, or under the inuence of alcohol or drugs.

• WARNING! Risk of Injection or Injury – Do not direct

discharge stream at persons.

• Do not overreach – Keep proper footing and balance at

all times.

• Avoid unintentional starting – Do not carry a plugged-

in machine with your nger on the trigger. Make sure the

switch is o before plugging in the machine.

• Do not abuse the cord – Never carry the machine by the

cord or yank the cord to disconnect it from the receptacle.

Keep the cord away from heat, oil, and sharp edges.

• Use safety glasses – Also use safety footwear, snug-tting

clothing, protective gloves, hearing and head protection.

• Check the water temperature – This pressure washer is not

meant to pump hot water. NEVER connect it to a hot water

supply as it will signicantly reduce the life of the pump.

• Store indoors – NEVER store the pressure washer

outdoors or where it could freeze. The pump could be

seriously damaged.

• Inspect electrical cables – The insulation of the power cord

should be perfectly intact. If the power cord is damaged or

shows any signs of wear or tear, do not use the pressure

washer. Contact your authorized Snow Joe

®

+ Sun Joe

®

dealer or call the Snow Joe

®

+ Sun Joe

®

customer service

center at 1-866-SNOWJOE (1-866-766-9563).

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! This appliance has been designed for

use with cleaning agents that are recommended by the

manufacturer. The use of other cleaning agents or chemicals

may adversely aect the safety of the appliance.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

• Do not direct the jet at yourself or others in order to clean

clothes or footwear.

• Risk of explosion – Do not spray ammable liquids.

• Disconnect the tool – Disconnect from the electrical

power supply before performing any maintenance task.

2

• Keep children away – This high-pressure electric

power washer must not be used by children or

untrained personnel.

• To ensure appliance safety, use only original replacement

parts from the manufacturer or those approved by

the manufacturer.

mCAUTION! To prevent damage to the appliance, do not

allow it to operate dry. Before starting the appliance, make

sure that it has proper and stable supply of water.

mWARNING! Water that has owed through backow

preventers is considered to be non-potable.

mWARNING! During cleaning, maintenance or when

replacing parts, the machine must be disconnected from its

power source by removing the plug from the socket outlet.

mWARNING! High-pressure hoses, ttings, and

couplings are important for the safe operation of the appliance.

Use only hoses, ttings, and couplings recommended by

the manufacturer.

• Check for damaged parts – Do not use the appliance if

the supply cord or other important parts of the appliance

are damaged (e.g. safety devices, high-pressure hoses,

trigger gun).

mWARNING! If an extension cord is used, the plug and

socket must be of watertight construction.

mWARNING! Inadequate extension cords can be

dangerous.

• This high-pressure electric power washer must not be used

at temperatures below 32ºF (0°C).

mWARNING! Power cords on drums should always be

completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and o

the ground.

• If the power cord is damaged, do not use the appliance.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

• Keep the machine on a stable, at surface during operation,

handling, transportation, and storage. Sudden overturn of

the machine can cause bodily injury.

• In the event of an accident or breakdown, switch o the

machine immediately. (If contact with detergent occurs,

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical

MAINS, short voltage drops may appear when starting the

equipment. This can, in turn, inuence other equipment

(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax

< 0.335 OHM, such disturbances are not expected. (If you

require assistance, contact your local supply authority for

further information.)

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects. If

you nd any, do not start up your machine and contact your

distributor.

The following should be observed when connecting the

high-pressure electric power washer to the electric supply:

• The electric supply connection should be performed by a

qualied person.

• The electric supply to this appliance should include either

a residual current device that will interrupt the supply if the

leakage current to the earth exceeds 30 mA for 30 ms or a

device that will interrupt the earth circuit (GFCI).

IMPORTANT: Only use water without any impurities. If there

is a risk of running sand into the inlet water (i.e. from your own

well), an additional lter should be installed.

Safety Devices

The unloader valve can reduce pressure if it exceeds preset

values. The spray gun features a locking device. When the lock

is activated, the spray gun cannot be operated.

1. Thermal sensor – A thermal sensor protects the motor

against overloading. The machine will restart after a few

minutes when the thermal sensor has cooled.

2. Double insulation – In a double-insulated appliance, two

systems of insulation are provided instead of grounding.

No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added

to the appliance. Servicing a double-insulated appliance

requires extreme care and knowledge of the system, and

should be performed only by qualied service personnel at

an authorized Snow Joe® + Sun Joe® dealer. Replacement

parts for a double-insulated appliance must be identical

to the parts they replace. A double-insulated appliance

is marked with the words “Double Insulation” or “Double

Insulated.” The symbol (square within a square) may

also be marked on the appliance.

3. Ground fault circuit interrupter (GFCI) protection – this

product is provided with a Ground Fault Circuit Interrupter

built into the power cord plug. This device provides

additional protection from the risk of electric shock. If

replacement of the plug or cord is needed, use only

identical replacement parts that include GFCI protection.

3

4. It is not recommended to use an extension cord with

this pressure washer. The unit comes standard with a

35 ft GFCI power cable. Using an extension cord may

cause a drop in line voltage resulting in loss of power and

overheating.

Use only extension cords that are intended for outdoor

use. These extension cords are identied by marking

"Acceptable for use with outdoor appliance; store indoors

while not in use". Use only extension cords having an

electrical rating not less than the rating of the product. Do

not use damaged extension cords. Examine extension

cord before using and replace if damaged. Do not

abuse extension cord and do not yank on any cord to

disconnect. Keep cord away from heat and sharp edges.

Always disconnect extension cord from the receptacle

before disconnecting the product from the extension cord.

5. To reduce the risk of electric shock, this appliance has a

polarized plug (i.e. one blade is wider than the other). The

appliance plug will t into a polarized outlet only one way.

If the appliance plug does not t fully into the outlet,

reverse the plug. If the plug still does not t, make sure

that you are using the correct polarized wall outlet. If the

plug still does not t, contact a qualied electrician to

install the proper wall outlet. Do not modify the appliance

plug, power cord receptacle, or power cord plug in

any way.

6. To prevent the appliance cord from disconnecting from the

extension cord during operation, make a knot with the two

cords as shown in Table 1.

7. Do not abuse the cord. Never pull the pressure washer

by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil, and

sharp edges.

Risk of Electrocution

• Inspect cord before using.

• Do not use if cord is damaged.

• Keep all connections dry and o the ground.

• Do not touch plug with wet hands.

• Keep cord away from heat and sharp edges.

• Do not spray electrical apparatus and wiring.

Risk of Explosion

• Do not spray ammable liquids.

• Do not use acids, bases, solvents, or any ammable

material in this product. These substances can cause

physical injuries to the operator and irreversible damage to

the machine.

Additional Safety Instructions

• High-pressure: keep clear of nozzle.

• Injection hazard: equipment can cause serious injury if the

spray penetrates the skin.

• Do not point the gun at anyone or at any part of the body.

• In case of skin penetration, seek medical aid immediately.

• Before servicing, cleaning, or removing any parts, shut o

the power and relieve pressure.

• This machine is not suitable for connection to the potable

water mains.

m WARNING m

Electric shock may cause SEVERE INJURY or

DEATH. Heed these warnings:

• Do not allow any part of the electric pressure washer

to make contact with water while it is in operation. If

the appliance becomes wet while turned o, wipe dry

before starting.

• Do not use an extension cord over 25 ft. The

pressure washer comes equipped with a 35 ft power

cable. Combined cord length must not exceed 60 ft.

Any extension cord must be 14-gauge (or heavier) to

safely power the pressure washer.

• Do not touch the appliance or its plug with wet hands

or while standing in water. Wearing rubber boots

oers some protection.

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

25 ft (7.6 m)

14

(B) Connect plug and receptacle

Cord set Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

4

Product Description

Purpose

• This high-pressure electric power washer is intended for

residential use to clean vehicles, machines, buildings,

facades, etc.

Areas of Application

• Never use the machine in potentially explosive areas under

any circumstances!

• The operating temperature must be between 32ºF (0ºC) and

104ºF (40ºC).

• The machine consists of an assembly with a pump, which is

encased in a shock-absorbing housing. To provide the operator

with an optimal working position, the machine is equipped with

a stainless steel lance and a non-slip handle grip, whose shape

and conguration comply with applicable regulations.

• Do not cover or modify the stainless steel lance or the spray

nozzles in any way.

• The high-pressure electric power washer is designed to be

used with cold or lukewarm water; higher temperatures can

damage the pump.

• Do not use water that is dirty, gritty, or contains any

chemical products, as these could impair operation and

shorten the life of the machine.

5

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

To reduce the risk of injury, user

must keep all bystanders at least

49 ft (15 m) away.

Sound power level is 96 dB(A).

Always keep the power cable

away from heat sources, oils, or

sharp edges. Immediately remove

plug from the mains if the cable is

damaged, frayed, or entangled.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection

against injury, wear ear defenders

and safety goggles.

Double Insulation – When servicing,

use only identical replacement parts.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

Machine not suitable for connection

to the potable water mains.

WARNING! Electrical shock hazard.

WARNING! Turn the machine OFF

and disconnect it from the power

supply before inspecting, cleaning,

changing accessories, or conducting

any other maintenance task.

Symbols SymbolsDescriptions Descriptions

Wear non-slip footwear that will

protect your feet and improve your

footing on slippery surfaces.

Wear safety gloves during

use to protect hands.

Store indoors. Never store the

pressure washer outdoors.

If the pump freezes, permanent

damage may result.

6

Know Your Electric Pressure Washer

Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration

below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.

Save this manual for future reference.

1. Trigger gun

2. Trigger

3. Safety lock

4. High-pressure hose connection

5. Trigger gun holder

6. Stainless steel lance

7. Wheel (2)

8. Spray wand protector

9. Garden hose adapter (female

coupler)

10. Power cord with GFCI

11. On/O switch

12. Hose holder

13. Detergent bottle with foam cannon

14. Transport handle

15. Onboard storage for Quick-Nozzles

16. Cord holder

17. Water outlet (high-pressure

connection)

18. Needle clean-out tool

19. 0º Quick-Connect nozzle (red)

20. 15º Quick-Connect nozzle (yellow)

21. 25º Quick-Connect nozzle (green)

22. 40º Quick-Connect nozzle (gray)

23. High-pressure hose

24. Wheel + rim brush

25. Utility bristle brush

26. Transfer adapter

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19202122

23

24 25 26

7

Technical Data

Rated Voltage ......................................................120V ~ 60 Hz

Motor ............................................................................ 13-amp

Max Water Inlet Temperature ................................. 104ºF/40ºC

Max Water Inlet Pressure ............................................ 0.7 MPa

Rated Pressure ........................................................... 1700 PSI

Rated Flow ................................................................. 1.2 GPM

Steel-reinforced ......................................................... 20 ft (6 m)

High Pressure Hose Length

Detergent Bottle Capacity .................................. 33.8  oz (1 L)

Power Cord Length ................................ 35 ft (GFCI Protected)

Net Weight ..................................................... 28.4 lbs (12.9 kg)

Unpacking

Carton Contents

• Electric pressure washer

• Transport handle

• Trigger gun

• Stainless steel lance

• Four (4) Quick-Connect nozzles (0º, 15º, 25º, and 40º)

• Detergent bottle with foam cannon

• Wheel + rim brush

• Utility bristle brush

• Transfer adapter

• Four (4) large screws

• Two (2) small screws

• Spray wand protector

• Trigger gun holder

• Hose holder

• Needle clean-out tool

• High-pressure hose

• Garden hose adapter (female coupler) with two sealing rings

• Manual with registration card

1. Carefully remove the pressure washer and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new electric

pressure washer. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT! The equipment and packaging material are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suocation risk!

mWARNING! Do not connect to power supply until

assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

Assembly

1. Position the washer as CLOSE as possible to the

water supply.

2. The washer must be used on a secure and stable surface

in a standing, upright position (Fig. 1).

3. Slide the trigger gun holder into position (Fig. 2).

4. Slide the transport handle into position and secure it with

4 large screws (Fig. 3).

Fig. 1

Fig. 2

Trigger gun holder

8

5. To assemble the hose holder, slide the holder into position

(Fig. 4) and secure it to the unit with one small screw

(Fig. 5).

6. Click the detergent bottle with foam cannon and the 4

Quick-Connect nozzles in place in front and back of the

nozzle storage board (Figs. 6 - 7).

7. To assemble the spray wand protector, rst snap the tab

into the slot located at the bottom left side of the unit,

and then secure it in place with the remaining small screw

(Fig. 8).

Fig. 3

Transport

handle

Fig. 4

Hose holder

Fig. 5

Screw

Fig. 6

Detergent

bottle with foam

cannon

Nozzle storage

board

Fig. 7

Quick-Connect

nozzles

Nozzle

storage

board

Fig. 8

Spray wand protector Small screw

Slot

Tab

9

8. Fit the stainless steel lance into the trigger gun and rotate

the collar until the two parts are completely locked (Fig. 9).

9. Connect the high-pressure hose to the trigger gun

(Fig. 10).

10. Connect the high-pressure hose to the water outlet on the

washer (Fig. 11).

mWARNING! Keep hose away from sharp objects.

Bursting hoses may cause injury. Examine hoses regularly and

replace if damaged. Do not attempt to mend a damaged hose.

11. Connect the garden hose adapter (female coupler) to

the water inlet of the pressure washer, then thread your

garden hose (male end) into the garden hose adapter

(Fig. 12). The garden hose must have an internal diameter

of at least 13 mm (1/2 in.) and must be reinforced. The

water supply must be at least equal to the washer delivery

capacity.

NOTE: The machine is not suitable for connection to the

potable water main.

mWARNING! The machine is not suitable for connection

to the potable water main.

12. Attach garden hose to water supply (Fig. 13).

mWARNING! The intake water temperature must not

exceed 104ºF/40ºC. The water supply must not exceed

0.7 MPa.

mCAUTION! The washer must only be used with clean

water; use of unltered water containing corrosive chemicals

will damage the washer.

13. Make sure the On/O switch is set to the OFF (0) position

before plugging the unit into the power outlet (Fig. 14).

Fig. 9

Stainless

steel lance

Trigger gun

Collar

High-pressure hose

Trigger gun

Fig. 10

Fig. 11

High-pressure water outlet

(REAR)

High-pressure

hose

Fig. 12 Water inlet

(female coupler)

Garden hose

This end to

water inlet

Garden hose

(male end)

Fig. 13

Connect to water supply

Garden hose

10

14. Check that the electrical supply voltage and frequency

(Volt/Hz) correspond to those specied on the pressure

washer rating plate. If the power supply is correct, you

may now plug the pressure washer into the power outlet

(Fig. 15).

NOTE: The GFCI may need to be reset when rst plugged

into the electric outlet. Press the "Reset" button until the

power light indicator on the GFCI illuminates.

Operation

mIMPORTANT! This pressure washer is equipped with

a micro-switch sensitive to water ow. This Total Stop System

(TSS) senses water ow in the pump. When the trigger is

released, water stops owing through the pump. The TSS then

automatically turns the motor o to protect the pump from

overheating, thus saving energy and prolonging pump life.

1. Turn the water supply tap on completely.

2. Make sure the safety lock is down and in its original

position (Fig. 16), then press the trigger for a few seconds

until water ow is steady. This will allow air to escape and

discharge any residual pressure in the hose.

3. Turn the switch to the ON (I) position to start the pressure

washer (Fig. 17).

Using the Nozzles

Before beginning any cleaning task, determine the best nozzle

for the job. Each of the nozzles has a dierent spray pattern.

The nozzle patterns are 40˚ (for gentle cleaning), 25˚ (for all-

purpose cleaning), 15˚ (for tough jobs), and the 0˚ (for spot

cleaning or hard-to-reach areas).

mCAUTION! NEVER change nozzles without locking the

safety lock on the trigger handle.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

This electric pressure washer is equipped with four (4) Quick-

Connect nozzles that easily snap onto the Quick-Connect

collar of the stainless steel lance.

To connect a nozzle to the stainless steel lance:

1. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

Fig. 14

On/Oswitch

RESET

TEST

Fig. 15

GFCI

Power light

indicator

Reset

Fig. 16 Safety lock

Slot

Trigger

Fig. 17

11

2. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 18).

3. Snap the desired nozzle onto the Quick-Connect collar

until it clicks into place (Fig. 19).

To disconnect a nozzle from the stainless steel lance once the

cleaning job is complete:

4. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

5. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 18).

6. Remove the nozzle by placing your hand over the nozzle

while pulling back on the Quick-Connect collar.

mWARNING! Do not make changes to the nozzle while

the trigger is engaged. Doing so could result in damage to the

pressure washer or injury to the user.

Working with Detergents

When cleaning with the pressure washer, some cleaning tasks

can be solved with water alone, but for most tasks cleaning

with detergent allows for more eective dirt removal.

For additional cleaning power, the unit comes equipped with a

detergent spray bottle with foam cannon.

mWARNING! Use only detergents specically designed

for use with pressure washers, such as Sun Joe® HOUSE +

DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO

WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER

(SPX-APC1G). DO NOT USE household detergents, acids,

alkaline solutions, bleaches, solvents, ammable material, or

industrial grade solutions. These could damage the pressure

washer. Many detergents may require mixing prior to use.

Prepare the cleaning solution as instructed on the solution

bottle.

1. Remove the foam cannon from the nozzle storage board.

Remove the foam cannon cap with detergent suction tube

from the bottle.

2. Fill the foam cannon bottle with detergent designed

specically for use with pressure washers (Fig. 20).

3. Recap the foam cannon, and attach it to the stainless

steel lance by snapping it onto the Quick-Connect collar

until it clicks into place (Fig. 21).

4. The foam cannon is featured with a foam-volume

adjustable knob. Follow the instructions as shown to use

the foam-volume adjustable knob (Fig. 22).

Fig. 18

Safety lock

Slot

Fig. 19

Nozzle

“Click”

Quick-Connect collar

Stainless steel lance

Fig. 20

Foam cannon

bottle

Pressure washer

detergent

Fig. 21

Foam cannon

“Click”

Quick-Connect collar

Stainless

steel lance

12

5. Apply detergent from the bottom to the top of the dry

surface to be cleaned. Applying detergent in this manner

will dissolve dirt most eectively.

NOTE: Wetting the surface rst is not recommended as it

dilutes the detergent and reduces its cleaning ability.

mCAUTION! Always test the detergent in an

inconspicuous area before use.

6. Allow the detergent to remain on the surface for a short

time before rinsing with the pressure washer. Do not allow

the detergent to dry on the surface.

mCAUTION! Damage may occur to painted surfaces

if the detergent is allowed to dry on them. Wash and rinse a

small section at a time. Avoid working on hot surfaces or in

direct sunlight.

Rinsing with the Pressure Washer

1. Turn o the pressure washer and shut o the water supply.

2. Pull the trigger to release water pressure.

3. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 18).

4. Remove the detergent bottle with foam cannon by holding

the bottle while pulling back on the Quick-Connect collar.

5. Select the right nozzle for the job (Fig. 23):

i) The 0º intense-jet nozzle (red) is an extremely powerful

nozzle that delivers a high-pressure, pencil-point jet

stream. It is used to cut heavy dirt deposits in a small,

concentrated area. It is ideal for dissolving stubborn

substances, like tar and grease spots on concrete,

or for removing caked mud from equipment. Use this

nozzle to clean hard-to-reach areas including the

facades of 2-story buildings or the undersides of lawn

mowers and tractors.

NOTE: Care should be used when choosing the

right nozzle to avoid permanently gouging wood or

damaging fragile surfaces.

ii) Use the 15º fan-tip nozzle (yellow) for intense cleaning

jobs on hard surfaces. Applications include stripping

paint, removing oil stains, grease, heavy mildew stains,

and rust from steel. This nozzle should only be used in

areas that can withstand the high-pressure from this

nozzle.

iii) Use the 25º fan-tip nozzle (green) to clean home

siding, brick patios, wood decks, driveways, or

sidewalks. When using this nozzle, test a small area

rst to avoid surface damage.

iv) Use the 40º wide-spray tip nozzle (gray) to clean items

such as cars, trucks, boats, patio furniture, or lawn

equipment.

6. Start at the top of the area to be rinsed and work your way

down, making sure to overlap your strokes.

Fig. 22

Foam-volume

adjustable

knob

15º

25º 40º

0º

Fig. 23

13

mIMPORTANT! NEVER USE:

• Bleach, chlorine products, and other corrosive chemicals

• Liquids containing solvents (e.g. paint thinners, gasoline,

oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the unit and will damage the

cleaning surface.

Using the Brush Attachments

This pressure washer is equipped with 2 brush attachments,

a utility brush and a heavy-duty wheel + rim brush. To

connect the brush attachments with the spray gun, follow the

instruction below.

1. Disconnect the stainless steel lance from the trigger gun

by twisting counterclockwise.

2. First connect the transfer adapter by inserting it into the

spray gun and twisting clockwise, as shown (Fig. 24).

3. Take the desired brush attachment and align the two

tabs with the inside of the transfer adapter. Once aligned,

push the brush attachment into the trigger gun, twist

counterclockwise to lock into place (Fig. 25).

NOTE: The brush attachments cannot be attached with

the spray gun without the transfer adapter.

Shutting Down

1. Turn the switch to the OFF (0) position and unplug the

power cord from the outlet.

2. Turn o the water source.

3. Hold the trigger to release water pressure.

4. Disconnect the garden hose from the water inlet on

the unit.

5. Disconnect the high-pressure hose connection on the

trigger gun handle.

6. Release the trigger and engage the gun safety lock.

mWARNING! Turn o the water supply and squeeze the

trigger to depressurize the unit. Failure to do so could result in

personal injury due to discharge of high-pressure water.

Taking a Break

If you are taking a break of ve minutes or more between

cleaning tasks:

1. Engage the gun safety lock (Fig. 18).

2. Turn the switch to the OFF (0) position.

3. Unplug the power cord from the outlet.

Storage

mCAUTION! Always store your pressure washer in a

location where the temperature will not fall below 32ºF (0ºC).

The pump in this machine is susceptible to permanent damage

if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE

WARRANTY.

• Store the pressure washer indoors in a dry, covered area

where it is not subject to adverse weather conditions.

• It is important to store this product in a frost-free area.

• Always empty water from all hoses, the pump, and the

foam cannon before storing.

Fig. 24

Trigger gun

Transfer adapter

Fig. 25

Trigger gun

Transfer adapter

Utility brush

Rim + wheel brush

14

mCAUTION! The use of a pump protector is

recommended to prevent cold weather damage during storage

over the winter months.

Winterizing + Long-Term Storage

If you must store your pressure washer in a location where

the temperature falls below 32ºF (0ºC), you can minimize the

chance of damage to your machine by utilizing the following

procedure:

• Disconnect all water connections.

• Turn on the machine for a few seconds until the remaining

water in the pump exits. Turn o immediately.

• Do not allow the high-pressure hose to become kinked.

• Store the machine and accessories in a room that does

not reach freezing temperatures.

• Do not store near a furnace or other sources of heat that

may dry out the pump seals.

• Operate the pressure washer with non-corrosive/non-toxic

anti-freeze, a pump saver, or a pump protector before

storing for the winter.

mWARNING! Before reusing, completely ush the unit

out with clear water. Anti-freeze products can damage

paintwork, so you must ensure there is no anti-freeze left in the

system before using it again.

Maintenance

mCAUTION! Before working on the pressure washer,

disconnect the plug from the power supply socket.

1. To ensure good performance, check and clean the water

inlet lter (Fig. 26). Remove the pre-lter and water inlet

lter and rinse with warm water to prevent any foreign

matter from clogging the pump (Figs. 27 – 28).

2. Clean the nozzle with the needle clean-out tool provided

(Fig. 29). Remove the stainless steel lance from the gun;

remove any dirt from the nozzle hole and rinse.

3. Remove additional debris by back ushing water through

the nozzle and stainless steel lance. To do this, place the

end of your garden hose (with water running) to the tip

of the nozzle, pushing water and debris out of the back

opening of the nozzle and stainless steel lance.

Fig. 26

Waterinletlter

Garden hose adapter

Pre-lter

Fig. 27

Pre-lter

Fig. 28

Inletlter

15º

Fig. 29

Needle clean-out tool

15

Disposal

Recycling the Washer

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

• When replacing old appliances with new ones, the retailer

is legally obligated to take back your old appliance for

disposal free of charge.

Service + Support

If your Sun Joe® SPX3000-XT1 electric pressure washer requires

service or maintenance, please call the Snow Joe® + Sun Joe®

customer service center at 1-866-SNOWJOE (1-866-766-9563).

Model + Serial Numbers

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide the

model and serial numbers, which can be found on the decal

located on the housing of the unit. Copy these numbers into

the space provided below.

Record the following numbers from the housing or handle of your

new product:

S P X 3 0 0 0 - X T 1

Model #:

Serial #:

16

Troubleshooting

• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that

its parts are in proper working order.

• The hose must be connected and the water turned on before operating your unit. Failure to do so will damage the pump

motor and void your warranty.

• Total Stop System (TSS) – The motor will shut OFF and remain in standby mode during periods of inactivity, or as soon as the

unit is pressurized. THIS IS NORMAL. Simply squeeze the trigger to restart the pump motor.

• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.

Problems Possible Cause Possible Solution

Machine refuses

to start

• Power failure/machine not

plugged into a working receptacle.

• Defective socket.

• Fuse has blown.

• Defective extension cord.

• Check to make sure machine is plugged into

a working outlet.

• Check the power cord and reset the GFCI.

Try a dierent outlet.

• Replace fuse. Switch o any other machines

that are using the same circuit.

• Try the unit without an extension cord.

• Check the hoses and connections are airtight.

• Clean or replace valves/seals.

• Please call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563)

for assistance.

• Replace fuse. Switch o other machines using

the same circuit.

• Check that the mains voltage corresponds to

specication on the model tag.

• Leave the washer for 5 minutes to cool down.

• Clean the nozzle.

• Install a fuse with a higher amp rating than the

amp consumption of the machine. Try the unit

without an extension cord.

• Allow machine to run by holding the trigger until

regular working pressure resumes.

• Check that the water supply corresponds to the

specications required.

• WARNING! Avoid using long, thin hoses

(minimum 1/2 in. diameter).

• Clean the nozzle.

• Clean the water inlet lter.

• Straighten out the hose to remove any kinks/blockages.

• Please call Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563) for

assistance.

• Wait for pump/hoses or accessories to thaw.

• Connect inlet water.

• Clean the water inlet lter.

• Clean the nozzle.

• Pump sucking air.

• Valves dirty, worn out, or stuck.

• Pump seals worn out.

• Fuse has blown.

• Incorrect mains voltage.

• Thermal sensor activated.

• Nozzle partially blocked.

• Fuse too small.

• Air in inlet hose.

• Inadequate supply of mains water.

• Nozzle partially blocked.

• Water lter blocked.

• Hose kinked.

• Pump/spray gun is leaking.

• Trigger mechanism is broken.

• Pump/hoses or accessories frozen.

• No water supply.

• Water inlet lter blocked.

• Nozzle blocked.

Fluctuating pressure

Machine stops

Fuse blows

Machine pulsating

Machine often starts

and stops by itself

Machine starts, but

no water comes out

17

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

Sun Joe’s complete line of premium pressure washer accessories and attachments

make it easy to get your dirty work done, and also help you get the most out of your model!

SHOP ONLINE now at sunjoe.com

Optional Accessories

mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use

replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe®

if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any

other attachment or accessory can be dangerous and could cause injury or mechanical damage.

Spray Tip Set

(Compatible with most

SPX Series Pressure Washers)

25 ft Medium-Duty

High Pressure Extension Hose

(For SPX Pressure Washer Series)

Solid Brass Universal Quick-Connect Coupler

(Garden Hose to Pressure Washer Adapter)

SPX3000-TPS

SPX-25H

SPX-UQC

ModelAccessories Item

1

3

4

2

SPX-HDC1G

SPX-FCS1G

SPX-APC1G

Sun Joe® House + Deck All-Purpose Pressure

Washer Rated Concentrated Cleaner

Sun Joe® Premium Snow Foam Pressure Washer

Rated Car Wash + Cleaner

Sun Joe® All-Purpose Heavy Duty Pressure

Washer Rated Cleaner + Degreaser

1155ºº

SOSOAAPP

2255ºº4400ºº

00ºº

5

3-Pack Pressure Washer Concentrate SPX-ASST3Q

R4_01282020

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used

for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased

from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality

of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from

unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,

Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no

charge, or (3) repair the Product. How cool is that!

This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:

Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and

mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE

(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty

rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:

This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?

This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also

does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do

not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased

at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as

possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under

normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty

(“Warranty”) for our Products.

18

EN

19

La page charge ...

sunjoe SPX3000-XT1 Le manuel du propriétaire

sunjoe SPX3000-XT1 Le manuel du propriétaire

dans d''autres langues