Dell PowerEdge R210 II Guide de démarrage rapide

Dell PowerEdge

R210 II Systems

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell PowerEdge

R210 II Systems

Getting Started

With Your System

Regulatory Model: E10S Series

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

___________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel

®

is a registered trademark and Core™ is a trademark of Intel Corporation in the U.S. and

other countries. Microsoft

®

and Windows Server

®

are either trademarks or registered trademarks

of Microsoft Corporation in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise

Linux

®

and are registered trademarks of Red Hat, Inc. in the United States and/or other countries.

SUSE ™ is a trademark of Novell, Inc. in the United States and other countries. Citrix

®

and

XenServer

®

are either registered trademarks or trademarks of Citrix Systems, Inc. in the United States

and/or other countries. VMware

®

is a registered trademarks or trademark of VMWare, Inc. in the

United States or other countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model E10S Series

December 2010 P/N RGTPR Rev. A00

Getting Started With Your System 3

Installation and Configuration

WARNING: Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item.

Installing the Rails and System in a Rack

CAUTION: If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than room ambient.

Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by

the manufacturer.

For more information, see

"Technical Specifications" on page 9.

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

4 Getting Started With Your System

Optional—Connecting the Keyboard, Mouse, and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable

to plug into each connector. Be sure to tighten the screws (if any) on the

monitor's cable connector.

Connecting the Power Cable

Connect the system’s power cable to the system and, if a monitor is used,

connect the monitor’s power cable to the monitor.

Getting Started With Your System 5

Securing the Power Cable

Bend the system power cable as shown in the illustration and secure the cable

in the retention clip.

Plug the other end of the power cable into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS) or

a power distribution unit (PDU).

Turning On the System

Press the power button on the system and the monitor. The power indicators

should light.

6 Getting Started With Your System

Installing the Optional Bezel

Install the bezel (optional).

Complete the Operating System Setup

If you purchased a preinstalled operating system, see the operating system

documentation that ships with your system. To install an operating system for

the first time, see the installation and configuration documentation for your

operating system. Be sure the operating system is installed before installing

hardware or software not purchased with the system.

Supported Operating Systems

• Microsoft Small Business Server 2011 Standard and Essential Editions

• Microsoft Windows Server 2008 R2 SP1 (x64) Web, Standard,

Foundation, and Enterprise Editions

• Microsoft Windows

Server 2008 R2 (x64) Web, Standard, Foundation,

and Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x86) Web, Standard,

and Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x64) Web, Standard,

and Enterprise Editions

• Microsoft Windows Server 2008 R2 SP1(x64) with Hyper-V for

Standard and Enterprise Editions

Getting Started With Your System 7

• Microsoft Windows Server 2008 R2 (x64) with Hyper-V for Standard and

Enterprise Editions

• Microsoft Windows Server 2008 SP2 (x64) with Hyper-V for Standard and

Enterprise Editions

• VMware ESX 4.1 Update 1 (Classic)

• VMware ESX 4.1 Update 1 (Embedded)

• Citrix XenServer 5.6 Feature Pack 1

• Red Hat Enterprise Linux

6.0 (x86_64)

• SUSE Linux Enterprise Server 11 SP1 (x86_64)

NOTE: For the latest information on supported operating systems,

see support.dell.com.

Dell Software License Agreement

• Before using your system, please read the Dell Software License

Agreement that came with your system.

• You must consider any CD, DVD, or diskette set of Dell installed

software as BACKUP copies of the software installed on your system's

hard-disk drive.

• If you do not accept the terms of the agreement, please call the customer

assistance telephone number. For customers in the United States,

call 800-WWW-DELL (800-999-3355). For customers outside the

United States, visit

support.dell.com

and select your country or region

from the top of the page.

8 Getting Started With Your System

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document

or as a separate document.

• The rack documentation included with your rack solution describes how

to install your system into a rack.

•The

Owner’s Manual

provides information about system features

and describes how to troubleshoot the system and install or replace

system components. This document is available online at

support.dell.com/manuals

.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, including those pertaining

to the operating system, system management software, system updates,

and system components that you purchased with your system.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Owner’s Manual. Dell offers

comprehensive hardware training and certification. See dell.com/training

for more information. This service may not be offered in all locations.

Getting Started With Your System 9

Technical Specifications

Processor

Processor type One Intel Core processor i3-2100 product family

or

One Intel Xeon processor E3-1200 product family

or

One Intel Pentium processor (when available)

Expansion Bus

Bus type PCI Express Generation 2

Expansion slots One full-height, half-length x16 link

Memory

Architecture 1066 MHz and 1333 MHz DDR3 unbuffered

Error Correcting Code (ECC) DIMMs

Memory module sockets Four 240-pin

Memory module capacities 1 GB, 2 GB, 4 GB, or 8 GB

Minimum RAM 1 GB

Maximum RAM 32 GB

Drives

Hard drives Up to two 3.5-inch cabled SAS or SATA

internal drives

or

Up to two 2.5-inch cabled SAS or SATA

internal drives

Optical drive One optional internal SATA DVD-ROM or

DVD+/-RW drive

NOTE: DVD devices are data only.

Optional external USB DVD-ROM

10 Getting Started With Your System

Connectors

Back

NIC

Two RJ-45 (for integrated 1 GB NICs)

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

eSATA

One 7-pin connector

Front

Video

15-pin VGA

USB

Two 4-pin, USB 2.0-compliant

Internal

USB

Two 4-pin, USB 2.0-compliant

Video

Video type Matrox G200, integrated in Winbond WPCM450

Video memory 8 MB

Power

AC power supply (per power supply)

Wa tt ag e

250 W

Voltage

100 VAC–240 VAC, 50 Hz/60 Hz, 4.0 A–2.0 A

Heat dissipation

1040 BTU/hr maximum

Maximum inrush current

Under typical line conditions and over the entire

system ambient operating range, the inrush

current may reach 25 A

Batteries

System battery

CR 2032 3.0-V lithium coin cell

Getting Started With Your System 11

Physical

Height 4.24 cm (1.67 inches)

Width 43.4 cm (17.09 inches)

Depth 39.37 cm (15.5 inches)

Weight

(maximum configuration)

8.058 kg (17.77 lb)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets.

Temperature

Operating

10 °C to 35 °C (50 °F to 95 °F) with a maximum

temperature gradation of 10 °C per hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–40 °C to 65 °C (–40 °F to 149°F) with a

maximum temperature gradation of 20 °C

per hour

Relative humidity

Operating

20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5 Hz–350 Hz for 15 min

Storage

1.87 Grms at 10 Hz–500 Hz for 15 min

12 Getting Started With Your System

Maximum shock

Operating

One shock pulse in the positive z axis (one pulse

on each side of the system) of 31 G for 2.6 ms in

the operational orientation

Storage

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G for

up to 2 ms

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse

on each side of the system) of 32 G faired

square wave pulse with velocity change at

270 inches/second (686 centimeters/second)

Altitude

Operating

–16 m to 3048 m (–50 ft to 10,000 ft)

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1 ºF/550 ft.

Storage

–16 m to 10,600 m (–50 ft to 35,000 ft)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Environmental (continued)

Systèmes

Dell PowerEdge R210 II

Guide de mise en route

Modèle réglementaire : série E10S

Remarques, précautions et avertissements

REMARQUE : Une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre ordinateur.

PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque d'endommagement

du matériel ou de perte de données en cas de non-respect des instructions.

AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement

du matériel, de blessures corporelles ou même de mort.

___________________

Les informations que contient cette publication sont sujettes à modification sans préavis.

La reproduction de ce document de quelque manière que ce soit sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques utilisées dans ce document : Dell™, le logo DELL et PowerEdge™ sont des marques de

Dell Inc. Intel

®

est une marque déposée et Core™ est une marque d'Intel Corporation aux États-Unis

et dans d'autres pays. Microsoft

®

et Windows Server

®

sont des marques ou des marques déposées de

Microsoft Corporation aux États-Unis et/ou dans d'autres pays. Red Hat

®

et Red Hat Enterprise Linux

®

sont des marques déposées de Red Hat, Inc. aux États-Unis et/ou dans d'autres pays. SUSE™ est une

marque de Novell, Inc. aux États-Unis et dans d'autres pays. Citrix

®

et XenServer

®

sont des marques

déposées ou des marques de Citrix Systems, Inc. aux États-Unis et/ou dans d'autres pays. VMware

®

est une marque déposée ou une marque de VMware, Inc. aux États-Unis et dans d'autres pays.

D'autres marques et noms commerciaux peuvent être utilisés dans ce document pour faire référence

aux entités se réclamant de ces marques et de ces noms ou à leurs produits. Dell Inc. rejette tout intérêt

propriétaire dans les marques et les noms commerciaux autres que les siens.

Modèle réglementaire : série E10S

Décembre 2010 N/P RGTPR Rév. A00

Guide de mise en route 15

Installation et configuration

AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous,

lisez les consignes de sécurité fournies avec le système.

Déballage du système

Sortez le système de son emballage et identifiez chaque élément.

Installation des rails et du système dans un rack

PRÉCAUTION : Si le système est installé dans un rack clos ou multi-unités,

la température ambiante du rack lors du fonctionnement du système peut être plus

élevée que celle de la pièce. Il est donc important de veiller à installer l'équipement

dans un environnement compatible avec la température ambiante maximale (Tma)

spécifiée par le fabricant.

Pour plus d'informations, voir

« Caractéristiques

techniques » à la page 21.

Assemblez les rails et installez le système dans le rack en suivant les consignes

de sécurité et les instructions d'installation du rack fournies avec votre

système.

16 Guide de mise en route

Facultatif : connexion du clavier, de la souris et du moniteur

Connectez le clavier, la souris et le moniteur (facultatif).

Aidez-vous des icônes des connecteurs situés à l'arrière du système pour

savoir où insérer chaque câble. N'oubliez pas de serrer les vis situées sur

le connecteur du câble du moniteur, s'il en est équipé.

Branchement du câble d'alimentation

Branchez le câble d'alimentation au système et, si vous utilisez un moniteur,

branchez son câble d'alimentation.

Guide de mise en route 17

Fixation du câble d'alimentation

Pliez le câble d'alimentation comme le montre l'illustration et faites-le passer

dans le clip de fixation.

Branchez ensuite l'autre extrémité du câble d'alimentation sur une prise

secteur mise à la terre ou sur une source d'alimentation autonome (onduleur

ou unité de distribution de l'alimentation).

Mise sous tension du système

Appuyez sur le bouton d'alimentation du système et sur celui du moniteur.

Les voyants d'alimentation s'allument.

18 Guide de mise en route

Installation du cadre en option

Installez le cadre (en option).

Finalisation de l'installation du système

d'exploitation

Si vous avez acheté un système d'exploitation préinstallé, consultez la

documentation connexe fournie avec le système. Voir la documentation

relative à l'installation et à la configuration du système d'exploitation si vous

installez celui-ci pour la première fois. Veillez à installer le système

d'exploitation avant tout élément matériel ou logiciel acheté séparément.

Systèmes d'exploitation pris en charge

• Microsoft Small Business Server 2011, éditions Standard et Essential

• Microsoft Windows Server 2008 R2 SP1, éditions Web, Standard,

Foundation et Enterprise (x64)

• Microsoft Windows

Server 2008 R2, éditions Web, Standard,

Foundation et Enterprise (x64)

• Microsoft Windows Server 2008 SP2, éditions Web, Standard et

Enterprise (x86)

• Microsoft Windows Server 2008 SP2, éditions Web, Standard et

Enterprise (x64)

La page charge ...

Dell PowerEdge R210 II Guide de démarrage rapide

Ce manuel convient également à

Dell PowerEdge R210 II Guide de démarrage rapide

dans d''autres langues

Documents connexes