ESAB Migmaster 250 Welding Packages Troubleshooting instruction

Marque: ESAB

Modèle: Migmaster 250 Welding Packages

Catégorie: Système de soudage

Taper: Troubleshooting instruction

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles

of operation and safe practices for arc welding equipment, we urge you to read our booklet,

"Precautions and Safe Practices for Arc Welding, Cutting and Gouging." Form 52-529. Do NOT permit

untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate

this equipment until you have read and fully understand these Instructions. If you do not fully

understand these Instructions, contact your supplier for further information. Be sure to read the

Safety Precautions Section before installing or operating this equipment.

MIGMASTER 250

WELDING PACKAGES

Be sure this information reaches the operator.

You can get extra copies through your supplier.

INSTRUCTIONS for

F-15-087-F

June, 1999

NOTE: This manual is also suitable for use with L-TEC Migmaster 250 package.

TABLE OF CONTENTS

SECTION NO. PAGE NO.

SECTION 1 - SAFETY PRECAUTIONS FOR WELDING

AND CUTTING ........................................................................................................... 3

SECTION II - INTRODUCTION .............................................................................................7

2.1 GENERAL ..................................................................................................................7

2.2 RECEIVING-HANDLING ............................................................................................ 7

2.3 DESCRIPTION, Available Packages/Contents ...........................................................7

2.4 OPTIONAL ACCESSORIES.......................................................................................8

2.5 SAFETY ................................................................................................................... 10

SECTION III - INSTALLATION ...........................................................................................10

3.1 LOCATION ............................................................................................................... 10

3.2 ELECTRICAL INPUT CONNECTIONS .................................................................... 10

3.3 SECONDARY OUTPUT CONNECTIONS................................................................ 13

3.4 TORCH CONNECTIONS ......................................................................................... 13

3.5 WIRE FEEDER MECHANISM.................................................................................. 13

3.6 CONNECTION OF THE SHIELD GAS ..................................................................... 14

3.7 WELDING CABLE CONNECTIONS.........................................................................15

3.8 ASSEMBLE REAR WHEELS ...................................................................................15

3.9 INSTALLING OPTIONAL SPOT/STITCH/ANTI-STICK MODULE ............................ 15

3.10 INSTALLING OPTIONAL DIGITAL METER ............................................................. 15

SECTION IV - OPERATION................................................................................................16

4.1 CONTROLS..............................................................................................................16

4.2 PROCESS SETUP ................................................................................................... 17

4.3 OPERATING PROCEDURES .................................................................................. 20

SECTION V - SERVICE ...................................................................................................... 23

5.1 MAINTENANCE ....................................................................................................... 23

5.2 INSPECTION AND SERVICE .................................................................................. 23

5.3 TROUBLESHOOTING..............................................................................................24

SECTION VI - PARTS......................................................................................................... 27

6.1 SPARE PARTS ........................................................................................................27

6.2 REPLACEMENT PARTS.......................................................................................... 27

6.3 ORDERING ..............................................................................................................27

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and accompanying

labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided.

This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be used. Parts

that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or

replacement become necessary, the manufacturer recommends that a telephone or written request for service advice

be made to the Authorized Distributor from whom purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The

user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty

maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility

designated by the manufacturer.

10/98

WARNING: These Safety Precautions are for

your protection. They summarize precaution-

ary information from the references listed in

Additional Safety Information section. Before

performing any installation or operating procedures, be

sure to read and follow the safety precautions listed below

as well as all other manuals, material safety data sheets,

labels, etc. Failure to observe Safety Precautions can result

in injury or death.

PROTECT YOURSELF AND OTHERS --

Some welding, cutting, and gouging

processes are noisy and require ear

protection. The arc, like the sun, emits

ultraviolet (UV) and other radiation and

can injure skin and eyes. Hot metal can cause burns.

Training in the proper use of the processes and equip-

ment is essential to prevent accidents. Therefore:

1. Always wear safety glasses with side shields in any work

area, even if welding helmets, face shields, and goggles

are also required.

2. Use a face shield fitted with the correct filter and cover

plates to protect your eyes, face, neck, and ears from

sparks and rays of the arc when operating or observing

operations. Warn bystanders not to watch the arc and

not to expose themselves to the rays of the electric-arc

or hot metal.

3. Wear flameproof gauntlet type gloves, heavy long-sleeve

shirt, cuffless trousers, high-topped shoes, and a weld-

ing helmet or cap for hair protection, to protect against

arc rays and hot sparks or hot metal. A flameproof apron

may also be desirable as protection against radiated

heat and sparks.

4. Hot sparks or metal can lodge in rolled up sleeves,

trouser cuffs, or pockets. Sleeves and collars should be

kept buttoned, and open pockets eliminated from the

front of clothing

5. Protect other personnel from arc rays and hot sparks

with a suitable non-flammable partition or curtains.

6. Use goggles over safety glasses when chipping slag or

grinding. Chipped slag may be hot and can fly far.

Bystanders should also wear goggles over safety glasses.

FIRES AND EXPLOSIONS -- Heat from

flames and arcs can start fires. Hot slag

or sparks can also cause fires and ex-

plosions. Therefore:

1. Remove all combustible materials well away from the

work area or cover the materials with a protective non-

flammable covering. Combustible materials include wood,

cloth, sawdust, liquid and gas fuels, solvents, paints and

coatings, paper, etc.

2. Hot sparks or hot metal can fall through cracks or

crevices in floors or wall openings and cause a hidden

smoldering fire or fires on the floor below. Make certain

that such openings are protected from hot sparks and

metal.“

3. Do not weld, cut or perform other hot work until the

workpiece has been completely cleaned so that there

are no substances on the workpiece which might pro-

duce flammable or toxic vapors. Do not do hot work on

closed containers. They may explode.

4. Have fire extinguishing equipment handy for instant use,

such as a garden hose, water pail, sand bucket, or

portable fire extinguisher. Be sure you are trained in its

use.

SAFETY PRECAUTIONS

5. Do not use equipment beyond its ratings. For example,

overloaded welding cable can overheat and create a fire

hazard.

6. After completing operations, inspect the work area to

make certain there are no hot sparks or hot metal which

could cause a later fire. Use fire watchers when neces-

sary.

7. For additional information, refer to NFPA Standard 51B,

"Fire Prevention in Use of Cutting and Welding Pro-

cesses", available from the National Fire Protection Asso-

ciation, Batterymarch Park, Quincy, MA 02269.

ELECTRICAL SHOCK -- Contact with live

electrical parts and ground can cause

severe injury or death. DO NOT use AC

welding current in damp areas, if move-

ment is confined, or if there is danger of

falling.

1. Be sure the power source frame (chassis) is connected

to the ground system of the input power.

2. Connect the workpiece to a good electrical ground.

3. Connect the work cable to the workpiece. A poor or

missing connection can expose you or others to a fatal

shock.

4. Use well-maintained equipment. Replace worn or dam-

aged cables.

5. Keep everything dry, including clothing, work area, cables,

torch/electrode holder, and power source.

6. Make sure that all parts of your body are insulated from

work and from ground.

7. Do not stand directly on metal or the earth while working

in tight quarters or a damp area; stand on dry boards or

an insulating platform and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn off the power before removing your gloves.

10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)

for specific grounding recommendations. Do not mistake

the work lead for a ground cable.

ELECTRIC AND MAGNETIC FIELDS —

May be dangerous. Electric current flow-

ing through any conductor causes lo-

calized Electric and Magnetic Fields

(EMF). Welding and cutting current cre-

ates EMF around welding cables and

welding machines. Therefore:

1. Welders having pacemakers should consult their physi-

cian before welding. EMF may interfere with some pace-

makers.

2. Exposure to EMF may have other health effects which are

unknown.

3. Welders should use the following procedures to minimize

exposure to EMF:

A. Route the electrode and work cables together. Secure

them with tape when possible.

B. Never coil the torch or work cable around your body.

C. Do not place your body between the torch and work

cables. Route cables on the same side of your body.

D. Connect the work cable to the workpiece as close as

possible to the area being welded.

E. Keep welding power source and cables as far away

from your body as possible.

FUMES AND GASES -- Fumes and

gases, can cause discomfort or harm,

particularly in confined spaces. Do

not breathe fumes and gases. Shield-

ing gases can cause asphyxiation.

Therefore:

1. Always provide adequate ventilation in the work area by

natural or mechanical means. Do not weld, cut, or gouge

on materials such as galvanized steel, stainless steel,

copper, zinc, lead, beryllium, or cadmium unless positive

mechanical ventilation is provided. Do not breathe fumes

from these materials.

2. Do not operate near degreasing and spraying opera-

tions. The heat or arc rays can react with chlorinated

hydrocarbon vapors to form phosgene, a highly toxic

gas, and other irritant gases.

3. If you develop momentary eye, nose, or throat irritation

while operating, this is an indication that ventilation is not

adequate. Stop work and take necessary steps to im-

prove ventilation in the work area. Do not continue to

operate if physical discomfort persists.

4. Refer to ANSI/ASC Standard Z49.1 (see listing below)

for specific ventilation recommendations.

5. WARNING: This product, when used for welding or

cutting, produces fumes or gases which

contain chemicals known to the State of

California to cause birth defects and, in

some cases, cancer. (California Health &

Safety Code §25249.5 et seq.)

CYLINDER HANDLING -- Cylinders, if

mishandled, can rupture and violently

release gas. Sudden rupture of cylin-

der, valve, or relief device can injure or

kill. Therefore:

1. Use the proper gas for the process and use the proper

pressure reducing regulator designed to operate from

the compressed gas cylinder. Do not use adaptors.

Maintain hoses and fittings in good condition. Follow

manufacturer's operating instructions for mounting regu-

lator to a compressed gas cylinder.

2. Always secure cylinders in an upright position by chain

or strap to suitable hand trucks, undercarriages, benches,

walls, post, or racks. Never secure cylinders to work

tables or fixtures where they may become part of an

electrical circuit.

3. When not in use, keep cylinder valves closed. Have

valve protection cap in place if regulator is not con-

nected. Secure and move cylinders by using suitable

hand trucks. Avoid rough handling of cylinders.

4. Locate cylinders away from heat, sparks, and flames.

Never strike an arc on a cylinder.

5. For additional information, refer to CGA Standard P-1,

"Precautions for Safe Handling of Compressed Gases in

Cylinders", which is available from Compressed Gas

Association, 1235 Jefferson Davis Highway, Arlington,

VA 22202.

EQUIPMENT MAINTENANCE -- Faulty or

improperly maintained equipment can

cause injury or death. Therefore:

1. Always have qualified personnel perform the installa-

tion, troubleshooting, and maintenance work. Do not

perform any electrical work unless you are qualified to

perform such work.

2. Before performing any maintenance work inside a power

source, disconnect the power source from the incoming

electrical power.

3. Maintain cables, grounding wire, connections, power

cord, and power supply in safe working order. Do not

operate any equipment in faulty condition.

4. Do not abuse any equipment or accessories. Keep

equipment away from heat sources such as furnaces,

wet conditions such as water puddles, oil or grease,

corrosive atmospheres and inclement weather.

5. Keep all safety devices and cabinet covers in position

and in good repair.

6. Use equipment only for its intended purpose. Do not

modify it in any manner.

ADDITIONAL SAFETY INFORMATION -- For

more information on safe practices for elec-

tric arc welding and cutting equipment, ask

your supplier for a copy of "Precautions and

Safe Practices for Arc Welding, Cutting and

Gouging", Form 52-529.

The following publications, which are available from the

American Welding Society, 550 N.W. LeJuene Road, Mi-

ami, FL 33126, are recommended to you:

1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"

2. AWS C5.1 - "Recommended Practices for Plasma Arc

Welding"

3. AWS C5.2 - "Recommended Practices for Plasma Arc

Cutting"

4. AWS C5.3 - "Recommended Practices for Air Carbon

Arc Gouging and Cutting"

5. AWS C5.5 - "Recommended Practices for Gas Tungsten

Arc Welding“

6. AWS C5.6 - "Recommended Practices for Gas Metal Arc

Welding"“

7. AWS SP - "Safe Practices" - Reprint, Welding Hand-

book.

8. ANSI/AWS F4.1, "Recommended Safe Practices for

Welding and Cutting of Containers That Have Held

Hazardous Substances."

MEANING OF SYMBOLS - As used through-

out this manual: Means Attention! Be Alert!

Your safety is involved.

Means immediate hazards which, if

not avoided, will result in immediate,

serious personal injury or loss of life.

Means potential hazards which could

result in personal injury or loss of life.

Means hazards which could result in

minor personal injury.

SP98-10

a. Éloigner suffisamment tous les matériaux combus-

tibles du secteur où l’on exécute des soudures ou des

coupes à l’arc, à moins de les recouvrir complètement

d’une bâche non-inflammable. Ce type de matériaux

comprend notamment le bois, les vêtements, la sciure,

l’essence, le kérosène, les peintures, les solvants, le

gaz naturel, l’acétylène, le propane et autres sub-

stances combustibles semblables.

b. Les étincelles ou les projections de métal incandes-

cent peuvent tomber dans des fissures du plancher ou

dans des ouvertures des murs et y déclencher une

ignition lente cachée. Veiller à protéger ces ouvertures

des étincelles et des projections de métal.

c. N’exécutez pas de soudures, de coupes, d’opérations

de gougeage ou autres travaux à chaud à la surface

de barils, bidons, réservoirs ou autres contenants

usagés, avant de les avoir nettoyés de toute trace de

substance susceptible de produire des vapeurs

inflammables ou toxiques.

d. En vue d’assurer la prévention des incendies, il

convient de disposer d’un matériel d’extinction prêt à

servir immédiatement, tel qu’un tuyau d’arrosage, un

seau à eau, un seau de sable ou un extincteur portatif.

e. Une fois le travail à l’arc terminé, inspectez le secteur

de façon à vous assurer qu’aucune étincelle ou projec-

tion de métal incandescent ne risque de provoquer

ultérieurement un feu.

3. CHOC ÉLECTRIQUE-- Le gougeage à l’arc et à l’arc

au plasma exige l’emploi de tensions à vide

relativement importantes; or, celles-ci risquent de

causer des dommages corporels graves et même

mortels en cas d’utilisation inadéquate. La gravité du

choc électrique reçu dépend du chemin suivi par le

courant à travers le corps humain et de son intensité.

a. Ne laissez jamais de surfaces métalliques sous ten-

sion venir au contact direct de la peau ou de

vêtements humides. Veillez à porter des gants bien

secs.

b. Si vous devez effectuer un travail sur une surface

métallique ou dans un secteur humide, veillez à assu-

rer votre isolation corporelle en portant des gants secs

et des chaussures à semelles de caoutchouc et en

vous tenant sur une planche ou une plate-forme

sèche.

c. Mettez toujours à la terre le poste de soudage/coupage

en le reliant par un câble à une bonne prise de terre.

d. N’utilisez jamais de câbles usés ou endommagés. Ne

surchargez jamais le câble. Utilisez toujours un

équipement correctement entretenu.

e. Mettez l’équipement hors tension lorsqu’il n’est pas en

service. une mise à la masse accidentelle peut en

effet provoquer une surchauffe de l’équipement et un

danger d’incendie. Ne pas enrouler ou passer le câble

autour d’une partie quelconque du corps.

f. Vérifiez si le câble de masse est bien relié à la pièce en

un point aussi proche que possible de la zone de

travail. Le branchement des câbles de masse à

l’ossature du bâtiment ou en un point éloigné de la

zone de travail augmente en effet le risque de pas-

sage d’un courant de sortie par des chaînes de

PRÉCAUTIONS DE SÉCURITÉ

AVERTISSEMENT: Ces règles de sécurité ont pour objet

d’ assurer votre protection. Veillez à lire et à observer les

précautions énoncées ci-dessous avant de monter l’

équipement ou de commercer à l’utiliser. Tout défaut

d’observation de ces précautions risque d’entraîner des

blessures graves ou mortelles.

1. PROTECTION INDIVIDUELLE-- Les brûlures de la

peau et des yeux dues au rayonnement de l’arc

électrique ou du métal incandescent, lors du soudage

au plasma ou à l’électrode ou lors du gougeage à

l’arc, peuvent s’avérer plus graves que celles

résultant d’une exposition prolongée au soleil. Aussi

convient-il d’observer les précautions suivantes:

a. Portez un écran facial adéquat muni des plaques

protectrices et des verres filtrants appropriés afin de

vous protéger les yeux, le visage, le cou et les oreilles

des étincelles et du rayonnement de l’arc électrique

lorsque vous effectuez des soudures ou des coupes

ou lorsque vous en observez l’exécution.

AVERTISSEZ les personnes se trouvant à proximité

de façon à ce qu’elles ne regardent pas l’arc et à ce

qu’elles ne s’exposent pas à son rayonnement, ni à

celui du métal incandescent.

b. Portez des gants ignifugés à crispins, une tunique

épaisse à manches longues, des pantalons sans

rebord, des chaussures à embout d’acier et un

casque de soudage ou une calotte de protection, afin

d’éviter d’exposer la peau au rayonnement de l’arc

électrique ou du métal incandescent. ll est également

souhaitable d’utiliser un tablier ininflammable de

façon à se protéger des étincelles et du rayonnement

thermique.

c. Les étincelles ou les projections de métal incandes-

cent risquent de se loger dans des manches

retroussées, des bords relevés de pantalons ou dans

des poches. Aussi convient-il de garder boutonnés le

col et les manches et de porter des vêtements sans

poches à l’avant.

d. Protégez des étincelles et du rayonnement de l’arc

électrique les autres personnes travaillant à proximité

à l’aide d’un écran ininflammable adéquat.

e. Ne jamais omettre de porter des lunettes de sécurité

lorsque vous vous trouvez dans un secteur où l’on

effectue des opérations de soudage ou de coupage à

l’arc. Utilisez des lunettes de sécurité à écrans ou

verres latéraux pour piquer ou meûler le laitier. Les

piquetures incandescentes de laitier peuvent être

projetées à des distances considérables. Les

personnes se trouvant à proximité doivent également

porter des lunettes de protection.

f. Le gougeage à l’arc et le soudage à l’arc au plasma

produisent un niveau de bruit extrêmement élevé (de

100 à 114 dB) et exigent par conséquent l’emploi de

dispositifs appropriés de protection auditive.

2. PRÉVENTION DES INCENDES-- Les projections de

laitier incandescent ou d’étincelles peuvent

provoquer de graves incendies au contact de

matériaux combustibles solides, liquides ou gazeux.

Aussi faut-il observer les précautions suivantes:

levage, des câbles de grue ou divers chemins

électriques.

g. Empêchez l’apparition de toute humidité, notamment

sur vos vêtements, à la surface de l’emplacement de

travail, des câbles, du porte-électrode et du poste de

soudage/coupage. Réparez immédiatement toute

fuite d’eau.

4. VENTILATION-- La respiration prolongée des fumées

résultant des opérations de soudage/coupage, à

l’intérieur, d’un local clos, peut provoquer des mal-

aises et des dommages corporels. Aussi convient-il

d’observer les précautions suivantes:

a. Assurez en permanence une aération adéquate de

l’emplacement de travail en maintenant une ventila-

tion naturelle ou à l’aide de moyens mécaniques.

N’effectuez jamais de travaux de soudage ou de

coupage sur des matériaux de zinc, de plomb, de

beryllium ou de cadmium en l’absence de moyens

mécaniques de ventilation capables d’empêcher

l’inhalation des fumées dégagées par ces matériaux.

b. N’effectuez jamais de travaux de soudage ou de

coupage à proximité de vapeurs d’hydrocarbure

chloré résultant d’opérations voisines de dégraissage

ou de pulvérisation. La chaleur dégagée ou le

rayonnement de l’arc peut déclencher la formation de

phosgène -- gaz particulièrement toxique -- et d’autres

gaz irritants, à partir des vapeurs de solvant.

c. Une irritation momentanée des yeux, du nez ou de la

gorge constatée au cours de l’utilisation de

l’équipement dénote un défaut de ventilation. Arrêtez-

vous de travailler afin de prendre les mesures néces-

saires à l’amélioration de la ventilation. Ne poursuivez

pas l’opération entreprise si le malaise persiste.

d. Certaines commandes comportent des canalisations

où circule de l’hydrogène. L’armoire de commande est

munie d’un ventilateur destiné à empêcher la forma-

tion de poches d’hydrogène, lesquelles présentent un

danger d’explosion; ce ventilateur ne fonctionne que

si l’interrupteur correspondant du panneau avant se

trouve placé en position ON (Marche). Veillez à

manœuvrer cette commande en vérifiant si le

couvercle est bien en place, de façon à assurer

l’efficacité de la ventilation ainsi réalisée. Ne jamais

débrancher le ventilateur.

e. Les fumées produites par l’opération de soudage ou

de coupage peuvent s’avérer toxiques. Aussi est-il

nécessaire de disposer en permanence d’un dispositif

adéquat de ventilation de type aspirant, afin d’élimi-

ner du voisinage de l’opérateur tout dégagement de

fumée visible.

f. Consultez les recommandations particulières en

matière de ventilation indiquées à l’alinéa 6 de la

norme Z49.1 de l’AWS.

5. ENTRETIEN DE L’ÉQUIPEMENT-- Un équipement

entretenu de façon défectueuse ou inadéquate risque

non seulement de réaliser un travail de mauvaise

qualité mais, chose plus grave encore, d’entraîner des

dommages corporels graves, voire mortels en

déclenchant des incendies ou des chocs électriques.

Observez par conséquent les précautions suivantes:

a. Efforcez-vous de toujours confier à un personnel qua-

lifié l’installation, le dépannage et l’entretien du poste

de soudage et de coupage. N’effectuez aucune

réparation électrique sur l’équipement à moins d’être

qua-lifié à cet effet.

b. Ne procédez jamais à une tâche d’entretien

quelconque à l’intérieur du poste de soudage/

coupage, avant d’avoir débranché l’alimentation

électrique.

c. Maintenez en bon état de fonctionnement les câbles,

le câble de masse, les branchements, le cordon

d’alimentation et le poste de soudage/coupage.

N’utilisez jamais le poste ou l’équipement s’il présente

une défectuosité quelconque.

d. Prenez soin du poste de soudage et de coupage et

des équipements accessoires. Gardez-les à l’écart

des sources de charleur, notamment des fours, de

l’humidité, des flaques d’eau maintenez-les à l’abri des

traces d’huile ou de graisse, des atmosphères corro-

sives et des intempéries.

e. Laissez en place tous les dispositifs de sécurité et tous

les panneaux de l’armoire de commande en veillant à

les garder en bon état.

f. Utilisez le poste de soudage/coupage conformément à

son usage prévu et n’effectuez aucune modification.

6. INFORMATIONS COMPLÉMENTAIRES RELATIVES

À LA SÉCURITÉ--

Pour obtenir des informations complémentaires sur les

règles de sécurité à observer pour le montage et

l’utilisation d’équipements de soudage et de coupage

électriques et sur les méthodes de travail

recommandées, demandez un exemplaire du livret N°

52529 “Precautions and Safe Practices for Arc Weld-

ing, Cutting and Gouging” publié par ESAB. Nous

conseillons également de consulter les publications

sui-vantes, tenues à votre disposition par l’American

Welding Society, 550 N.W. LeJuene Road, Miami, FL

32126:

a. “Safety in Welding and Cutting” AWS Z49.1

b. “Recommended Safe Practices for Gas-Shielded Arc

Welding “AWS A6. 1.

c. “Safe Practices for Welding and Cutting Containers

That Have Held Combustibles” AWS-A6.0.

d. “Recommended Safe Practices for Plasma Arc Cut-

ting” AWS-A6. 3.

e. “Recommended Safe Practices for Plasma Arc Weld-

ing” AWS-C5. 1.

f. “Recommended Safe Practices for Air Carbon Arc

Gouging and Cutting” AWS-C5. 3.

g. “Code For Safety in Welding and Cutting”

CSA-Standard W117. 2.

9/97

Depending on the primary input voltage of the MM-250,

and the torch length, each package includes the follow-

ing:

l One (1), Migmaster 250 Power Supply/Wire Feeder

equipped with a dual-groove feed roll (for .035/.045 wire),

a 6'-0" ft. primary input power cable and plug (plug is

installed for 208/230-V. units only), a mating input power

receptacle rated @ 50A./250-V. (packed loose for 208/

230-V. input packages only), 10-ft. work cable w/clamp,

a 6'-0" shielding gas supply hose w/fittings and running

gear w/gas (cylinder) support, as follows:

-- Migmaster 250 for 208/230-Volt input ....P/N 32851

-- Migmaster 250 for 208/230/380/400/460/575-Volt

input.......................................................P/N 32852

l One (1), Migmaster 250 Kit as follows:

-- 12-ft. Pkg.

Includes:

MT-200cc, ready-to-weld, 12-ft. lg. torch

for .035/.045 wire.......................................P/N 21116

R-33-FM-580 Regulator, (F-15-173) ...........P/N 21557

Mig Welding Process Handbook.............. P/N 791F18

10 # Sample Spool Wire .035 87 HP Wire

-- 15-ft. Pkg.

Includes same accessories as 12-ft. Kit except for torch,

which is:

MT-200cc, 15-ft. lg. for .035/.045 wire, .......P/N 21117

Kits are the same as 12-ft. Pkg. except Regulator is

R-33-FM-320. P/N 21558.

2.3.2 POWER SUPPLY

The power supply consists of a tapped single phase

transformer, tap selection switches, secondary contactor,

single phase full wave rectifier, stabilizing reactor, slope

resistor, filtering capacitors and internal output connec-

tions for polarity reversal.

2.3.3 WIRE FEEDER

The wire feeder pushes 0.023, 0.030, 0.035 and 0.045 in.

wire at speeds up to 650 IPM. Dynamic braking prevents

excessive wire overrun. A double grooved drive roll

(0.035 and 0.045 in. - supplied) provides a convenient

means of changing the setup for either wire size.

The wire feeder is built into the power supply cabinet, and

is housed in a compartment separated from the welding

machine components. Machine ventilation is not drawn

through this compartment, thus helping to keep the wire

and feeding mechanism clean.

II. INTRODUCTION

2.1 GENERAL

This manual has been prepared especially for use in

familiarizing personnel with the design, installation, op-

eration, maintenance, and troubleshooting of this equip-

ment. All information presented here in should be given

careful consideration to assure optimum performance of

this equipment.

2.2 RECEIVING-HANDLING

Prior to installing this equipment, clean all packing mate-

rial from around the unit and carefully inspect for any

damage that may have occurred during shipment. Any

claims for loss or damage that may have occurred in

transit must be filed by the purchaser with the carrier. A

copy of the bill of lading and freight bill will be furnished

by the carrier on request if occasion to file claim arises.

When requesting information concerning this equipment,

it is essential that Part, Serial and Model Numbers of the

equipment be supplied.

2.3 DESCRIPTION

The Migmaster 250 is a portable Welding System de-

signed for fine wire, (0.023, 0.030, 0.035 and 0.045 in.)

welding using the short arc method, as well as for spray

arc aluminum, short arc and spray arc stainless steel and

spray arc cored wires. It incorporates a running gear with

provisions for one gas cylinder, and a ST-23A spool-on-

gun control.

2.3.1 AVAILABLE PACKAGES AND CONTENTS

The following Migmaster 250 Packages are available

with Argon Regulator:

MM-250 for 208/230-V.

Input w/12-ft. Pkg. ............................... P/N 604560

MM-250 for 208/230-V.

Input w/15-ft. Pkg. ............................... P/N 604561

MM-250 for 208/230/380/400/460/575-V.

Input w/12-ft. Pkg. ............................... P/N 604563

MM-250 for 208/230/380/400/460/575-V.

Input w/15-ft. Pkg. ............................... P/N 604570

The following Migmaster 250 packages are available

with CO

Regulator:

MM-250 for 208/230-V

Input w/12-ft. Pkg. ................................P/N 35678

MM-250 for 208/230/380/400/460/575-V

Input w/12 ft. Pkg. ................................P/N 35763

2.3.6 RUNNING GEAR

The Migmaster 250 is equipped with a running gear w/

swiveled front wheels and a gas cylinder support. The

rear wheels are packed loose for shipping, but are easily

installed, see Section 3.8.

2.4 OPTIONAL ACCESSORIES

2.4.1 SPOT/STITCH/ANTI-STICK MODULE, P/N

32858.

This easy-to-install, plug-in module mounts in place of

the lower blank cover plate of the upper-right front panel

location in the 250 unit. It enables the operator to use the

250 for Spot or Stitch or Continuous welding operations.

It also includes an adjustable Anti-Stick feature that

allows you to select various wire burnback times to

prevent wire from sticking in the puddle after a weld. For

installation, see Section 3.9 and for operating instruc-

tions see Section 4.2.

2.3.4 MT-200cc WELDING TORCH (F-15-085),

The lightweight air cooled welding gun included in se-

lected systems is supplied complete and ready to weld

0.035 in. steel wire. It is built with a one piece service

conduit and includes a 45 degree gooseneck. Changing

the contact tip to 0.045 in. allows the use of the larger

wire.

2.3.5 CONTROLS

The Migmaster 250 System can be used to weld hard and

aluminum wire with an optional ST-23A spool-gun torch.

An optional spot/stitch control allows a welder to spot or

stitch weld within a range of 0.4 to 3.5 seconds. The built-

in spool-on-gun adaptors and control, when used in

conjunction with the optional ST-23A torch, permits alu-

minum wire welding with the machine.

TABLE 1. SPECIFICATIONS

POWER SOURCE MIGMASTER 250

Rated Output 250 Amps @ 27 Volts d.c.

Duty Cycle, 208/230V Unit 50% @ 60 Hz.; 40% @ 50 Hz.

208/230/380/400/460/575V Unit 35% for 208 through 400V; 50% for 460 & 575V

Primary Input Single Phase 208/230; 208/230/380/400/460/575 Volts 50 60 Hz

Primary Input Amperes 208-71, 230-62, 380-37,400-36, 460-31, 575-25

Output Current Range 30 to 280 Amps.

Maximum Open Circuit Volts 55 v.d.c.

FEEDER

Feed Type Push

Wire Sizes: Hard 0.023" (0.6mm) through 0.045" (1.2mm)

Cored 0.030" (0.8mm) through 1/16" (1.6mm)

Soft 0.035" (0.9mm) and 3/64" (1.2mm)

Feed Rate 20-650 IPM

MT-200cc TORCH

Cooling Air

Gooseneck Angle 45 degrees

Rated 60% Duty Cycle

(DCRP) Amps: 200 w/Argon Mixtures, 300 w/CO

Conduit Length see section 2.3.1

PHYSICAL

Net Weight *210 lbs (95 Kg.)

Height *32.25 inches (819 mm)

Width *19.5 inches (495 mm)

Depth *40.0 inches (1016 mm)

*Includes running gear & bottle tray.

TABLE 2.4.5.1 Recommended MT-200cc Torch Accessories

Wire Contact Tips Liners

Size & Type Short (S) Medium (M) Long (L) 10' 12' 15'

Hard Wires & Cored Wires

.023" (.6mm) - 20543 999742 999743* - -

.030" (.8mm) - 20544 996994 948850 17717 -

.035" (.9mm) - 996995 996996 2075237 17718 2075238

.040" (1.0mm) - 37287 37288

.045" (1.2mm) 999578u 37290u 996998u 2075237 17718 2075238

.052" (1.4mm) 948340u 2075349u - 2075239 17719 2075240

1/16" (1.6mm) 948341u 37289u - 2075239 17719 2075240

Soft Wires (aluminum)

.035" (.9mm) - 996995 996996 948862 - -

.040" (1.0mm) - 37287 37288

3/64" (1.2mm) 999578 996999 996998 948863 - -

(S) Short contact tips are recommended for proper wire stick out for flux cored wire welding.

(M) Medium contact tips are recommended for proper wire stick out in spray transfer Mig

welding.

(L) Long contact tips are recommended for good visability and proper wire stick in dip transfer

Mig welding.

* Requires support liner for .023" wire. Order P/N 999797.

u New ID for improved arc performance on steel/flux cored wire.

2.4.4 TORCH NOZZLES

A No. 8 Nozzle (1/2" I.D.), P/N 998893 for the MT-200CC

Torch, is included in the Migmaster 250 package. This

slip-on type nozzle incorporates a permanent insulator/

spatter shield. Other standard duty slip-on nozzles with

insulator/spatter shield, are available seperatly:

No. 6 Nozzle, Tapered (3/8" I.D.)............ P/N 998895

No. 10 Nozzle (5/8" I.D.)......................... P/N 998894

No. 12S Spotweld Nozzle (3/4" I.D.)......... P/N 17316

The following heavy-duty slip-on nozzles with insulator/

spatter shield, are available seperatly:

No. 8 Nozzle (1/2" I.D.)........................... P/N 999471

No. 10 Nozzle (5/8" I.D.)......................... P/N 999472

No. 12 Nozzle (3/4" I.D.)......................... P/N 999473

No. 12 Spot Nozzle (3/4" I.D.) ................ P/N 999625

New Long Life MT Nozzles. These nozzles have a

patented coating to reduce weld spatter and extend the

life of the nozzle.

No. 6 XL Nozzle, (MT Std.).................P/N 998895XL

No. 8 XL Nozzle, (MT Std.).................P/N 998893XL

No. 10 XL Nozzle, (MT Std.)...............P/N 998894XL

No. 8 XL Nozzle, (MT HD)..................P/N 999471XL

No. 10 XL Nozzle, (MT HS) ................P/N 999472XL

2.4.5 TORCH/WIRE FEED ACCESSORIES -- See

Tables 2.4.5.1 and 2.4.5.2.

2.4.6 SPOOL SPACER

For 8" dia. spools..................................... P/N 17511

For 10" dia. spools................................... P/N 34330

If a Spotwelding operation is to be used, it is recom-

mended that you also order a #12S Spotweld Nozzle,

P/N 999625.

2.4.2 DIGITAL VOLT/AMMETER MODULE, P/N 32857.

This easy-to-install, plug-in module mounts in place of

the top blank cover plate of the upper-right front panel

location in the 250 unit. This unique meter module

alternately displays welding voltage and current (of the

dial-set welding condition) every 4-seconds. Two L.E.D.’s

labeled Amps and Volts provided below the meter win-

dows, alternately illuminate to indicate which condition is

being displayed. The voltage indication is displayed in

1/10-volt increments (e.g.: 20.5), while the current indi-

cation is usually displayed in three-whole digits (e.g.:

225). After the torch trigger is released, the meter will

continue to flash for 20-seconds the last condition used

during welding. At the end of this time, the meter will

reset to zero. For installation see Section 3.10.

2.4.3 ST-23A SPOOL-ON-GUN TORCH, P/N 19164

(see F-14-353).

The Migmaster 250 unit is equipped with a built-in control

for the ST-23A Spool-On-Gun welding torch. The ST-

23A is a high performance, 250 ampere continuous duty

spool-on-gun torch designed for the mig welding pro-

cess. It is completely portable (up to 30-ft.), air-cooled

and hand operated, and weighs less than three (3)

pounds. The gun is equipped with (30) foot lines. For

installation and operation, see Section 4.2.2.

MT-250SG Spool-On-Gun ........................ P/N 36779

(Requires Adapter, P/N 36833) See F-15-380.

Table2.4.5.2 Drive Roll & Guide Tube Selection

Upper

Wire Type / Lower Pressure Guide

Diameter Drive Roll Roll Tube

Hard Wires (V groove)

.023 in. (0.6mm) 21155 23612397 21163

.030 in. (0.8mm) 21155 23612397 21164

.035 in. (0.9mm)* 21156 23612397 21165

.040 in. (1.0mm)* 21156 23612397 21165

.045 in. (1.2mm)* 21156 23612397 21165

Soft (aluminum) Wires (U groove)

.035 in. (0.9mm) 21158 23612397 21167**

3/64 in. (1.2mm) 21159 23612397 21168**

Cored Wires (Serrated V groove - lower)

.030 in. (0.8mm) 21160 23612369 21164

.035 in. (0.9mm) 21160 23612369 21165

.040 in. (1.0mm) 21161 23612369 21165

.045 in. (1.2mm) 21161 23612369 21165

.052 in. (1.4mm) 21161 23612369 21166

1/16 in. (1.6mm) 21161 23612369 21166

Cored Wires (Serrated V groove - upper and lower)†

.045 in. (1.2mm) 37319 37319 21165

.052 in. (1.4mm) 37319 37319 21166

1/16 in. (1.6mm) 37320 37320 21166

* Supplied with Migmaster 250.

** Requires Support Tube 21169.

† Recommended for use with soft cored wires that are easy to

flatten.

40"

1/2"

32 ¼" Overall

2.5 SAFETY

Before the equipment is put into operation, the safety

section at the front of this manual should be read

completely. This will help avoid possible injury due to

misuse or improper welding applications.

The symbol which precedes safety notes appear-

ing throughout this manual means “Attention! Be Alert!

Your safety is involved.” The definitions relating to the

DANGER, WARNING and CAUTION safety notations

are described at the end of the Safety Section in the front

of this manual -- read them and their specific text

references carefully.

III. INSTALLATION

3.1 LOCATION (Figure 3.1)

A proper installation site should be selected for the

welding machine, if the unit is to provide dependable

service and remain relatively maintenance free.

A proper installation site permits freedom of air move-

ment into and out of the welding machine, and also least

subjects the unit to dust, dirt, moisture, and corrosive

vapors. A minimum of 18 inches (46 cm) unrestricted

space must be maintained between the welding ma-

chine side and rear panels and the nearest obstruction.

The installation site should also permit easy removal of

the welding machine outer enclosure for maintenance

functions.

CAUTION: Do not place any filtering device over the

intake air passages of the welding ma-

chine as this would restrict the volume of

intake air and thereby subject the welding

machine internal components to an over-

heating condition and subsequent failure.

Warranty is void if any type of filtering

device is used.

If a forklift vehicle is used for lifting the unit, be sure that

the lift forks are long enough to extend completely under

the base.

Do not operate the machine without the running

gear installed.

3.2 ELECTRICAL INPUT CONNECTIONS

It is recommended that a line disconnect switch be

installed in the input circuit to the welding machine.

This would provide a safe and convenient means to

completely remove all electrical power from the

welding machine whenever it is necessary to perform

any internal function on the unit. (See Figure 3.2A.)

Before making electrical input connections to the

welding machine, “Machinery Lockout Procedures”

should be employed. If the connections are to be

made from a line disconnect switch, the switch

should be padlocked in the off position. If the con-

nection is made from a fusebox, remove the fuses

from the box and padlock the cover in the closed

position. If locking facilities are not available, attach

a red tag to the line disconnect switch (or fuse box)

to warn others that the circuit is being worked on. If

the plug-cap is used, (see 3.2B) remove plug from

receptacle.

Figure 3.1 Dimensional Drawing

Figure 3.2 - Primary Connection

208/230 MODEL ONLY (With Plug-Cap)

208/230/380/400/460/575-V. MODELS

SINGLE-PHASE

THREE-PHASE

SINGLE-PHASE

THREE-PHASE

GRD

GREEN

CONDUCTOR

(GROUND)

GREEN

Fused

Line

Disconnect

Switch,

Circuit Breaker

Wall Receptacle

MIGMASTER

SYSTEM

CONNECTS HERE

Figure 3.2 A

Figure 3.2 B

Figure 3.2 DFigure 3.2 C

TABLE 3.1 Input Conductor and Fuse Size

Recommended

Full Primary

Primary Load Input Ground

Input Line Fuse Conductor Conductor

Volts Amperes Size Size Size

208 71 90 8 8

230 62 90 8 8

380 37 50 10 10

400 36 50 10 10

460 31 40 12 12

575 25 30 12 12

Only qualified personnel should make these

changes. Make certain the primary power has been

disconnected and all safety procedures have been

followed before proceeding with these instructions.

Fig. 3.3A shows the 230v and 208v connections for the

208/230 dual voltage model. Change over is made by

removing the right side panel below the wire feed com-

partment and switching the primary transformer tap at

the top of the power switch with the unused alternate

voltage tap located next to the main transformer (see

Fig. 3.3B). Both voltage taps (the one currently con-

nected to the switch and the unused alternate voltage)

are marked with the input voltage requirement. All units

are supplied from the factory connected for the highest

voltage (230 vac). Before switching the voltage taps,

verify the actual voltage requirement as well as the

current voltage connection to be certain re-connection is

necessary. If voltage tap re-connection is necessary, the

following paragraphs cover the procedure to switch the

voltage tap for either 208vac or 230vac input.

3.2.1 Input Electrical Requirements

Models of this welding machine are designed to be

operated from 208/230, or 208/230/380/400/460/575

volts single phase 50/60 Hz, depending on model. The

primary input voltage requirements are shown on the

welding machine nameplate.

3.2.2 Input Conductor Connections

The input power cord on 208/230 Volts primary input

model is provided with an attachment plugcap. The

plugcap will mate with a 250 Volts, 50 Ampere receptacle

conforming to NEMA 6-50 R configuration.

The receptacle should be wired to a separately fused

disconnect or circuit breaker of the size listed in Table

3.1. This disconnect or breaker can be wired to a single

phase system or to two conductors of a three phase

system. A third conductor for grounding should also be

connected between the disconnect and the receptacle.

Figure 3.2A illustrates wiring to a single phase system

and Figure 3.2B illustrates wiring to a three phase

system.

The 208/230/380/400/460/575 primary input voltage unit

is provided with a three conductor primary input cable

without plugcap. The ground lead of this cable should be

connected to a reliable ground and the two remaining

wires should be connected to the separately fused lines

of the disconnect or breaker as shown in Figures 3.2C

and 3.2D.

All machines leave the factory with their primary electri-

cal input requirements internally-connected for the high-

est voltage rating available in each model (e.g.: 230-volt

for the 208/230-volt units; and 575-volt for the "multi-

voltage" units).

When changing the input voltage connections, the

unused lead must be insulated and positioned to

prevent contact with any other internal components

of the machine or the machine side panel. The clear-

ance between the unused lead and other compo-

nents must be at least one inch (see Fig. 3.3B for

illustration of the proper position). FAILURE TO

INSULATE AND POSITION THIS LEAD PROPERLY

WILL CAUSE A SERIOUS SHOCK HAZARD.

Fig. 3.3C - Power Switch Connection

Fig. 3.3B - Position of Alternate Voltage Tap

Figure 3.3A - Primary Reconnections at Switch

For 208/230 Volt Models

The terminal labeled GRD is connected to the weld-

ing machine chassis and is for ground purposes

only. It must be connected to a good electrical

ground. Do not connect a conductor from the termi-

nal labeled GRD to any one of the L1, L2 terminals as

this will result in an electrically hot welding machine

chassis.

3.2.3 CONNECTING FOR 208 VAC INPUT

After the panel is removed, locate the 208 Vac lead (Fig.

3.3B) and cut the tie-wrap to remove the insulation

sleeving (on early models this lead may have been

wrapped with black electrical tape). Open the insulating

cover around the power switch (Fig. 3.3C.) to expose the

terminals and disconnect the 230 Vac lead from the top

of the switch as shown in Fig. 3.3A. Insulate the 230 Vac

lead that was removed from the power switch with

sleeving or approved electrical tape and re-position to a

safe area beside the transformer (see Fig. 3.3B), leaving

a minimum of one inch clearance from other compo-

nents and the side panel.

3.2.4 CONNECTING FOR 230 VAC INPUT

After the panel is removed, locate the 230 Vac lead (Fig.

3.3B) and cut the tie-wrap to remove the insulation

sleeving (on early models this lead may have been

wrapped with black electrical tape). Open the insulating

cover around the power switch (Fig. 3.3C.) to expose the

terminals and disconnect the 208 Vac lead from the top

of the switch as shown in Fig. 3.3A. Insulate the 208 Vac

lead that was removed from the power switch with

sleeving or approved electrical tape and re-position to a

safe area beside the transformer (see Fig. 3.3B), leaving

a minimum of one inch clearance from other components

and the side panel.

Connect the proper voltage (208 Vac or 230 Vac) tap to

the power switch and tighten securely. Check all other

leads connected to the power switch for tightness and

clearance from internal components before securing the

insulating cover around the power switch. Replace the

side panel.

3.2.5 Reconnecting from 575 VAC Input

Figure 3.3.1 shows you how to reconnect the "multi-

voltage" model from a 575-volt input to any of the

remaining available voltage inputs 200 or 380 or 400 or

460-volts. These connections are made by unscrewing

the right side panel below the wire feeding compartment,

and locating the primary voltage changeover terminal

board handing in the center of the lower compartment.

This board contains copper links which must be recon-

nected to match the silk-screened voltage designations

for the input you plan to use (it comes factory-connected

for a 575-volt input), see Figure 3.3.1.

3.3 SECONDARY OUTPUT CONNECTIONS

The Migmaster 250 Welding System is completely self-

contained so that the front panel torch fittings (Euro-type

MT and Spool gun) are internally connected to the

welding polarity (D.C. Reverse or D.C. Straight) via the

secondary output terminals located inside the wire feed-

ing compartment (see Fig. 4.1). The machine comes set

up for D.C.R.P. welding as described in Section 4.1.3.

3.4 TORCH CONNECTIONS

The torch (MT-200cc), which is supplied as standard

equipment with the Migmaster 250 System, is provided

with a euro-type adapter which directly connects to the

torch fitting mounted on the front panel. Line up matching

holes, push on and tighten locking collar. As shipped

from the factory, the euro or common connector type

torches are set-up for D.C.R.P. welding polarity (see

sections 3.3 or 4.1.3). To connect the spool-on-gun torch

(ST-23A) see Section 4.2.2.

3.5 WIRE FEEDER MECHANISM

3.5.1 DRIVE ROLLS

The drive roll has two grooves: the small groove feeds

0.035 in. diameter wire, the large groove feeds 0.045 in.

wire. The groove nearest the gear motor feeds the wire.

If the required groove is not in that position:

A. Release the pressure drive roll lever and lift the

assembly upward.

B. Remove the two (2) screws holding the drive roll to

the gear.

C.Reverse the drive roll on the drive roll shaft.

D.Replace the screws and tighten.

E. Secure the pressure drive roll assembly.

Figure 3.3.1-Primary Reconnections at Voltage

Changeover Terminal Board for 208/230/380/400/460/

575Volt Models

PRIMARY VOLTAGE CONNECTION CHART

VOLTAGE CONNECTION NO. OF STRIPS

1 - 2 1

208 6 - 7 1

7 - 8 FLEX

1 - 2 1

230 6 - 7 1

5 - 8 FLEX

380 3 - 7 2

4 - 8 FLEX

400 2 - 6 2

7 - 8 FLEX

460 2 - 6 2

4 - 8 FLEX

575 2 - 3 2

4 - 8 FLEX

3.5.2 WELDING WIRE SPOOL

As with any work area, make sure safety glasses

with side shields are worn when handling or chang-

ing wire or clipping wire off at the spool or at the end

of the torch. Hold onto the wire coming off the spool

with one hand before clipping. Serious eye injury

can result due to the springiness of the wire which

can quickly unravel, or a cut wire end which may

shoot across the room.

Install a spool of welding wire on the hub as follows:

A. Unscrew spool nut from hub.

B. Place wire spool on hub to rotate clockwise as wire

is unwound; hub pin must engage hole in spool.

C.Replace nut.

3.5.3 THREADING WELDING WIRE

A. Turn off power switch.

When the power switch is on, and gun trigger is

depressed, the electrode wire becomes electrically

hot, and the wire feed rolls are activated.

B. Release pressure drive roll assembly and lift up

ward. Check that proper wire diameter groove is in

the inner position.

CAUTION: Before threading welding wire through cas-

ing, make sure chisel point and burrs have

been removed from wire end to prevent wire

from jamming in gun casing or liner.

C.Feed the wire from the spool through the inlet

guide, across the drive roll groove and into gun

outlet guide.

Make sure that the proper “outlet guide tube” is inserted

into the front-panel gun fitting for the size and type of wire

being used, see Table 2.4.5.2 for wire feed accessories

(Section 2.4.5).

To insure proper wire feeding, it is important that the wire

be kept clean and that the drive rolls be periodically

cleaned of any chips or scale that might be carried into

the gun liner and cause sticking.

D.Lower pressure roll assembly and secure. Check

that the gears mesh. Feed wire through to gun tip

with gun trigger (power ON).

OUTLET

CONNECTION

CYLINDER

PRESSURE

GAUGE

f. Attach the gas hose from the rear of the Migmaster

250 to the regulator outlet connection (see Fig. 3.6).

g. Slowly open the cylinder valve a fraction of a turn.

When the regulator pressure gauge pointer stops

moving, open the cylinder valve fully.

Fig. 3.6 R-33-FM-580 Regulator (Illustrated)

CYLINDER

VALVE

3.5.4 BRAKE DRAG ADJUSTMENT

Brake disc friction should provide enough drag to keep

the wire spool or core from spinning freely after wire feed

stops. If adjustment is required, turn adjusting screw

clockwise to increase drag, counterclockwise to de-

crease it. Drag should be just low enough to limit wire

overrun.

3.6 CONNECTION OF SHIELDING GAS SUPPLY

The R-33-FM-580 Regulator-Flowmeter is designed for

use with an argon or argon-mix cylinder of shielding gas.

It is adjustable for delivering up to 50 cfh through the

torch. To set up the system do the following:

Do Not adapt R-33-FM-580 for use with CO

. Relief

device may rupture if CO

is used with the R-33-FM-

580. For CO

service, order R-33-FM-320, P/N 21558.

a. With the cylinder cap in place CAREFULLY slide

the cylinder of gas onto the Migmaster 250 cylinder

rack.

b. Secure the cylinder to the unit, using the chain

provided.

c. Unscrew the cylinder cap.

d. Open the cylinder valve slightly, just for an instant,

to blow away any dirt or dust which may have ac-

cumulated in the cylinder valve outlet. Be sure to

keep your face away from the valve outlet

to protect your eyes.

e. Attach the regulator to the cylinder valve, tighten

the union nut securely with a 1-1/8in. open end or

an adjustable wrench.

Never stand directly in front of or behind the regula-

tor when opening the cylinder valve. Always stand

to one side.

h. Using a leak test solution, such as P/N 998771 (8

oz. container) or soapy water, test for leakage

about the cylinder valve stem, the regulator inlet

connection, and the hose connections at the regu-

lator and at the Migmaster 250 for leakage. Correct

any leaks before starting work.

i. If work is to be stopped for a half-hour or more, or

the regulator is to be removed from the cylinder,

shut down the regulator as follows:

a. Close the cylinder valve.

b. Release gas from the regulator by closing the

torch trigger lever.

c. When pressure gauge drops to zero, the regu-

lator is de-pressurized and shutdown.

j. Each regulator is equipped with a porous metal

inlet filter, P/N 71Z33, pressed into the regulator

inlet nipple. No. regulator should be connected to

a cylinder or station valve unless it contains this

filter. You can replace the filter if you have reason

to do so. To remove a filter refer to the regulator

instruction literature for details.

k. Regulators in need of repair should be returned to

your Welding Equipment distributor or to an autho-

rized Remanufacturing Center.

If welding is performed in a confined area, shielding

gas leaks could result in a buildup of shielding gas

concentration, displacing oxygen, thereby endan-

gering personnel enter the area.

3.7 WELDING CABLE CONNECTIONS

Connect the work clamp solidly to the workpiece or work

table. Clamp onto a bare metal area.

A good electrical connection to the work is essential

to proper welding operation and to prevent electric

shock.

Welding cables should be kept as short as possible and

be of adequate current carrying capacity. Resistance of

the welding cables and connections causes a voltage

drop which is added to the voltage drop of the arc.

Excessive cable resistance may result in a reduction of

the maximum usable current output of the equipment.

The proper operation of this equipment is to a large

extent dependent on the use of welding cables and

connections which are in good condition and of adequate

size.

3.8 ASSEMBLE REAR WHEELS

The unit's running board is factory assembled except for

the rear wheels which are packed loose in the shipping

carton. The rear gear consists of 2-wheels, 4-washers,

2-cotter pins, and an axle. To install the gear, do the

following:

a. Insert the axle through the holes provided at the

rear of the gear.

b. Place a washer onto each end of the axle, then slip

on the wheels, then add another washer to the

outside of each wheel, and secure the whole as-

sembly by inserting a pin in each end of the axle.

c. Remove the existing shipping supports by un-

screwing from chassis.

3.9 INSTALLING OPTIONAL SPOT/STITCH/ANTI-

STICK MODULE

a. Remove lower blank-cover plate from upper-right

front panel of power supply -- save the four mount-

ing screws.

b. Locate the harness-connected 15-pin plastic plug,

P3, inside the mounting cavity. Note that this plug

will have a jumper plug with jumper wires con-

nected to it -- remove (and save) the jumper plug.

(The jumper plug must be reinstalled if the module

is ever removed.

c. Connect the 15-pin plug into the matching recep-

tacle on the rear of the optional control module. The

plug will only fit one way.

d. Install the control module in place of the blank

panel removed in Step a., using the same four

screws that you saved.

3.10 INSTALLING OPTIONAL DIGITAL METER

a. Remove the top blank-cover plate from the upper-

right front panel of the power supply -- save the four

mounting screws.

b. Locate the harness-connected 10-pin plastic plug,

PL1, inside the mounting cavity. This plug does

not have a jumper plug connected to it.

c. Connect the 10-pin plug into the matching recep-

tacle on the rear of the optional meter module.

d. Install the meter module in place of the blank-

panel removed in Step a., using the same four

screws that you saved.

IV. OPERATION

4.1 CONTROLS (See Figure 4.1)

4.1.1 POWER SWITCH

A line toggle switch on the front panel energizes the

primary of the main transformer. This switch also turns on

the fan, which is connected across a portion of the

primary winding.

Two transformer secondary windings also become ener-

gized:

A. Gun trigger circuit 24 volts AC.

Wire feeder circuit 24 volts DC.

B. Main welding secondary circuit. Depending upon

the tap switch position, various secondary volt-

ages can be obtained. Then rectified, open circuit

voltages can be selected between 18 and 56 volts

DC when the secondary contactor is energized.

4.1.2 VOLTAGE CONTROL (Coarse Range Selector

and Fine Adjustment Range Selector)

Voltage control is by means of two high current tap

switches which connect the rectifier bridge to various

secondary taps.

The COARSE VOLTAGE RANGE Selector is a three-

position switch, LOW/MED/HIGH, by which the operator

selects the approximate range of voltage (or heat, that

determines the arc length) to be applied to the weld. It is

a coarse selection control and is used in conjunction with

the Fine Voltage Adjustment selector following. It must

not be switched under load.

4.1.5

2.4.2

4.2.3

4.1.3

4.1.1

4.1.2

Work

Cable

4.1.6

4.2.2

Secondary Output Terminals

for Welding Polarity Change-

over, see 4.1.3.

10A. Fuse

Torch

Cable

The FINE VOLTAGE ADJUSTMENT Selector is an

eight-position switch by which the operator selects the

exact amount of arc voltage (or heat) to be applied to the

weld (within the coarse range selected above). This

allows you to fine-tune the voltage required; the higher

the number selected (1-8), the hotter the weld. The Fine

Voltage Selector switch also has an "open" detent at the

six o'clock position. Placing the switch in this position

allows operation of the torch trigger to feed electrode

wire without the wire being electircally "hot". This switch

also, must not be switched under load.

CAUTION: These tap switches carry several hundred

amperes, and must not be switched under

load, as this will cause the contacts of the

switches to arc.

4.1.3 SECONDARY WELDING CONNECTIONS

The secondary contactor, with parallel poles, is used to

make and break the circuit between the transformer

secondary and the rectifier. This contactor is turned on

and off when the torch trigger (in the 24 volt circuit) is

operated.

The secondary output welding terminals, POS.(+) and

NEG(-), are located in the right side wire feeding com-

partment and are used to set the welding polarity

(D.C.R.P. or D.C.S.P.) in which the machine will operate

(see Fig. 4.1). As shipped from the factory, the 250 is set

up to operate in D.C.R.P. (TORCH fitting is connected

to Positive, and WORK cable/clamp is connected to

Negative output). To weld using D.C.S.P., simply mount

the WORK cable to the Positive output and the TORCH

fitting cable to the Negative output terminal.

4.1.4 CONTACTOR CONTROL

Refer to the schematic diagrams. Note that the coil of

the 24 volt contactor is activated with the torch trigger

and is energized when the trigger is pulled. The gas

solenoid is in parallel with the contactor coil and is

energized at the same time.

When the trigger switch is released, the contactor drops

out and disconnects the load.

Because of the charged capacitor bank in the sec-

ondary circuit, the output voltage will take a few

seconds before falling to zero volts.

The gas valve shuts off when the contactor opens.

The Migmaster 250 is equipped with a built-in control for

the Spool Gun which operates via the amphenol control

receptacle and a screw adaptor that provides Gas and

Power. The ST-23A Torch (see Section 2.4.3) has a

amphenol-plug control cable connection, and a gas/

power cable, see Figure 4.2.2.

To operate the unit with the ST-23A Torch connected, do

the following (refer to Fig. 4.2.2):

A. Place the STD./Spool Gun selector toggle switch

(4.1.6) in the 250 to its Spool Gun position.

B. Connect the ST-23A control cable amphenol to the

receptacle labeled CONTROL on the 250s front

panel.

C. Remove the threaded plastic plug from the Gas/

Power adaptor (on the 250's front panel) using a

clockwise rotation. Connect the ST-23A gas/power

cable to the panel adaptor using a counter-

clockwise rotation. As shipped from the factory,

the 250's secondary output power terminals are

set-up for D.C.R.P. welding polarity (see Section

4.1.3). IMPORTANT -- Always make sure that

the plastic plug is screwed back into the adaptor

when the ST-23A gas/power cable is discon-

nected, because hielding gas will escape from the

adaptor unless the gas cylinder is shut-off.

4.1.5 WIRE FEED SPEED CONTROL

Wire feed speed is controlled by the wire speed potenti-

ometer knob on the front panel. The solid state control

allows for infinitely variable speeds up to 650 IPM.

This wire speed pot is used to set the speed at which the

welding wire is fed out from the torch and hence the

welding amperage. The panel-face numbers on the dial

(0-10) are used for reference and do not directly indicate

wire feed speed; the higher the number, the faster the

speed.

4.1.6 STD./SPOOL GUN SELECTOR

This two-position toggle switch is located inside the unit

on the mid-wall of the wire feeding compartment and is

labeled Standard and Spool Gun. It is used to select

standard metal inert gas welding (MIG) with the MT-

200CC, or welding with the ST-23A (spool-on-gun) torch.

4.2 PROCESS SETUP

4.2.1 STANDARD MIG SEAM WELDING W/MT-200CC

Refer to Sections 4.3.1, 4.3.2, 4.3.3, 4.3.4, and Table

4.3.3.

4.2.2 ST-23A SPOOL-ON-GUN CONTROL CONNEC-

TION/OPERATION

Figure 4.2.2 - Connecting Spool-On-Gun to Services

Anti-Stick feature provides a time delay at the end of a

weld from the time the torch trigger is released until the

main contactor is deenergized. This delay allows the

welding wire to burn back, away from the work, so it

wont stick in the weld puddle.

This delay time, controlled by the anti-stick potentiom-

eter, is variable from approximately 0.05 seconds to 0.5

seconds. The required delay time generally depends on

the WIRE SPEED Adjustment setting on the front panel

- the higher the setting, the faster wire will feed into the

weld, and the more delay time will be required.

If, when using the Anti-Stick feature, the welding wire

tends to stick in the puddle at the end of a weld, the Anti-

Stick time should be increased; if, on the other hand, the

wire burns back into the torch tip, the anti-stick time

should be decreased. Setting the anti-stick time to Min

effectively cancels the anti-stick feature.

This Anti-Stick feature is available for all three welding

modes - Continuous, Spot, and Stitch.

4.2.3.2 CONTINUOUS WELDING MODE OPERATION

A. Place the three-position toggle switch in Continu-

ous weld mode (center position) for mig seam

welding.

B. Set the Anti-Stick Time as required (see 4.2.3.1).

D. Connect the 250s WORK cable to the workpiece.

E. Set Migmaster 250 voltage tap switches to

RANGE and FINE ADJUSTMENT VOLTAGE set-

tings desir- ed.

F. Turn on the Migmaster 250s power switch and

begin seam mig welding.

If the optional Spot/Stitch/Anti-Stick control module is

installed, the MT-250SG and the ST-23A gun may be

operated using these optional features, see Section

4.2.3.

4.2.3 OPTIONAL SPOT/STITCH/ANTI-STICK CON-

TROL MODULE

This optional control module allows the operator to use

the 250 for Spot or Stitch or Continuous welding opera-

tions. It also includes an adjustable Anti-Stick feature to

select various burnback times to prevent wire from

sticking in the puddle after a weld.

The module consists of three pots (one for Spot-Stitch

Weld Time "ON", one for Stitch Weld Time "OFF", and

one for Anti-Stick Time modes) and one three-position

toggle switch to select the welding operation desired

(Spot, Continuous or Stitch). For installation, see Section

3.9; for operation, see following:

4.2.3.1 ANTI-STICK WELDING OPERATION

MT-250SG

MT-250SG Requires

Adapter 36833

C. Set the coarse and fine Voltage control

switches and wire speed pot to the desired settings

and begin welding operation as described in Sec-

tions 4.3.2 and 4.3.3.

4.2.3.3 SPOT WELDING MODE OPERATION

A. Place the three-position toggle switch in Spot

position.

B. Replace the standard nozzle with the No. 12 Spot

weld Nozzle P/N 999625.

C. Trim the welding wire back so the end is slightly

inside the nozzle.

D. Set the coarse and fine voltage control switch-

es, wire speed, and the Spot-Stitch Weld Time see

Table 4.3, for the thickness of the metal being

welded and the diameter of the weld wire being

used.

E. To spotweld:

i. Press the torch nozzle squarely on the top plate.

Apply enough pressure to hold the two pieces of

metal firmly together, so there is no loose play

between them.

Fig. 4.2.3 - Cross Section of Good Spotweld

ii. Pull the trigger, holding the gun motionless and

firmly. The electrode wire and shielding gas will

be fed to the work, and the arc will be maintain-

ed for the length of time set in Step D. above.

iii. After the preset time has elapsed, the wire will

stop feeding, the arc will be broken, and the

shielding gas will stop flowing.

A good spotweld will penetrate through both lay-

ers of metal, and will have a small nugget on the

reverse side, (Fig. 4.2.3)

4.2.4 STITCH WELDING MODE OPERATION

A. Place the three-position toggle switch in Stitch

position. The stitch weld mode uses a series of pre-

timed arc-on/arc-off time sequences to allow cooler

welding.

B. Be sure a standard nozzle (and not a spot weld

nozzle) is installed on the torch.

C. Set the length of time the arc will be ON for each

sequence by adjusting the Spot-Stitch Weld Time

control on the power supplys front panel. This

timer has an approximate range of from 0.4 sec-

onds at the minimum setting to 3.5 seconds at the

maximum setting. Set the length of time the arc will

be OFF for each sequence by adjusting the Stitch

Weld Time control on the front panel. This timer

has an approximate range of from 0.4 seconds at

the minimum setting to 3.5 seconds at the maxi-

mum setting.

D. Set the coarse and fine voltage control switches

and wire speed as specified in Table 4.3 under

Continuous Weld Conditions for:

i. The type weld being made (see diagrams to the

left of each column of figures).

ii. The thickness of the metal being welded.

iii. The gap (if any) between the pieces being weld-

ed.

iv. The diameter of the welding wire being used.

E. When using the Stitch weld mode, before starting

the weld the welding wire should extend about

1/ 2-in. beyond the end of the nozzle. Adjust this

length by either clipping off the end of the wire with

insulated cutters or by using the torch switch.

Power supply contactor becomes energized the mo-

ment the torch trigger is depressed. Arcing can

occur if the wire is brought to a ground. Keep the

torch always from ground until welding is to begin.

F. During the welding, use the same welding techni-

ques as described in Section 4.3.3 and 4.3.4.

4.2.5 DUTY CYCLE (Figure 4.2.5)

The duty cycle of the equipment is the percentage of a 10

minute period which it can operate safely at a given output

current. The Migmaster system is rated at 50% duty

cycle. This means that the equipment can be safely

operated at 250 amperes for five minutes out of every 10.

This cycle can be repeated indefinitely (See Figure

4.2.5).

Fig. 4.2.5 Duty Cycle Curves

4.2.6 VOLT/AMPERE CURVES (Figure 4.2.6)

The Volt/Ampere curves show the output Voltage avail-

able at any given output current for the various Voltage

Selector positions in each range low, medium, and high.

The actual operating point of load Voltage and Current

is determined by type of process, electrode, shield gas,

wire feed speed, and operating technique.

4.3 OPERATING PROCEDURES

4.3.1 OPERATING SAFETY PRECAUTIONS

Comply with all ventilation, fire and other safety require-

ments for arc welding as established in the SAFETY

Section at the front of this manual.

Also remember the following:

A. Because of the radiant energy of the welding arc

and the possibility of drawing an arc before the

helmet is lowered over the face, the operator

should wear flash goggles with filter lenses under

his helmet. The helmet filter plated should be

shade number 11 (nonferrous) or 12 (ferrous). All

those viewing the arc should use helmets with filter

plates, as well as flash goggles. Nearby personnel

should wear flash goggles.

B. The radiant energy of the arc can decompose

chlorinated solvent vapors, such as trichloroethy-

lene and perchlorethylene, to form phosgene,

even when these vapors are present in low con-

centrations. DO NOT weld where chlorinated sol-

vents are present in atmospheres in or around the

arc.

C. DO NOT touch the electrode, nozzle or metal parts

in contact with them when power in ON: all are

electrically energized (HOT) and can cause a

possibly fatal shock. DO NOT allow electrode

to touch grounded metal: it will create an arc flash

that can injure eyes. It may also start a fire or

cause other damage.

D. When working in a confined space, be sure it is

safe to enter. The confined space should be tested

for adequate oxygen (at least 19%) with an approv-

ed oxygen measuring instrument. The confined

space should not contain toxic concentrations of

fumes or gases. If this cannot be determined, the

operator should wear an approved air supplied

breathing apparatus.

Avoid gas leaks in a confined space, as the leaked gas

can dangerously reduce oxygen concentration in the

breathing air.

DO NOT bring gas cylinders into confined spaces.

When leaving a confined space, shut OFF gas supply at

the source to prevent gas from leaking into the space, if

the switch is accidently kept depressed. Check the

breathing atmosphere in the confined space to be sure

it is safe to reenter.

Figure 4.2.6 VOLT/AMPERE CURVES

La page charge ...

ESAB Migmaster 250 Welding Packages Troubleshooting instruction

Marque: ESAB

Modèle: Migmaster 250 Welding Packages

Catégorie: Système de soudage

Taper: Troubleshooting instruction

Télécharger le PDF

rapport

dans d''autres langues

English: ESAB Migmaster 250 Welding Packages

Documents connexes

Autres documents

Cebora 896 Plasma Prof 50 Manuel utilisateur