Electrolux KGG95375K Manuel utilisateur

KGG95375K

EN Hob User Manual 2

FR Table de cuisson Notice d'utilisation 25

DE Kochfeld Benutzerinformation 50

ES Placa de cocción Manual de instrucciones 76

CONTENTS

1. SAFETY INFORMATION....................................................................................2

2. SAFETY INSTRUCTIONS..................................................................................5

3. INSTALLATION.................................................................................................. 8

4. PRODUCT DESCRIPTION.............................................................................. 12

5. DAILY USE.......................................................................................................14

6. HINTS AND TIPS............................................................................................. 17

7. CARE AND CLEANING....................................................................................19

8. TROUBLESHOOTING......................................................................................20

9. TECHNICAL DATA...........................................................................................22

10. ENERGY EFFICIENCY.................................................................................. 23

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that

brings with it decades of professional experience and innovation. Ingenious and

stylish, it has been designed with you in mind. So whenever you use it, you can

be safe in the knowledge that you’ll get great results every time.

Welcome to Electrolux.

Visit our website to:

Get usage advice, brochures, trouble shooter, service and repair information:

www.electrolux.com/support

Register your product for better service:

www.registerelectrolux.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.

When contacting our Authorised Service Centre, ensure that you have the

following data available: Model, PNC, Serial Number.

The information can be found on the rating plate.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

1. SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damage that are the result

of incorrect installation or usage. Always keep the

www.electrolux.com2

instructions in a safe and accessible location for future

reference.

1.1 Children and vulnerable people safety

• This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning the use of the appliance in a

safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons

with very extensive and complex disabilities shall be

kept away from the appliance unless continuously

supervised.

• Children of less than 3 years of age should be kept

away from the appliance unless continuously

supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of

it appropriately.

• WARNING: Keep children and pets away from the

appliance when it operates or when it cools down.

Accessible parts become hot during use.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user

maintenance of the appliance without supervision.

1.2 General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to avoid

touching heating elements.

• WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch

off the appliance and then cover flame e.g. with a lid

or a fire blanket.

ENGLISH 3

• CAUTION: The appliance must not be supplied

through an external switching device, such as a timer,

or connected to a circuit that is regularly switched on

and off by a utility.

• CAUTION: The cooking process has to be supervised.

A short term cooking process has to be supervised

continuously.

• WARNING: Danger of fire: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they

can get hot.

• Do not use the appliance before installing it in the

built-in structure.

• Do not use a steam cleaner to clean the appliance.

• If the glass ceramic surface / glass surface is cracked,

switch off the appliance and unplug it from the mains.

In case the appliance is connected to the mains

directly using junction box, remove the fuse to

disconnect the appliance from power supply. In either

case contact the Authorised Service Centre.

• In case of hotplate glass breakage:

– shut immediately off all burners and any electrical

heating element and isolate the appliance from the

power supply,

– do not touch the appliance surface,

– do not use the appliance.

• If the supply cord is damaged, it must be replaced by

the manufacturer, an authorized Service or similarly

qualified persons in order to avoid a hazard.

• Where the appliance is directly connected to the

power supply, an all-pole isolating switch with a

contact gap is required. Complete disconnection in

compliance with the conditions specified in

overvoltage category III must be guaranteed. The

earth cable is excluded from this.

• When you route the mains cable, make sure that the

cable doesn't come into direct contact (for example

www.electrolux.com4

using insulating sleeving) with parts that can reach

temperatures of more than 50°C above room

temperature.

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by

the manufacturer of the appliance in the instructions

for use as suitable or hob guards incorporated in the

appliance. The use of inappropriate guards can cause

accidents.

2. SAFETY INSTRUCTIONS

This appliance is suitable for the

following markets: IT

2.1 Installation

WARNING!

Only a qualified person must

install this appliance.

WARNING!

Risk of injury or damage to

the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from

other appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture from causing

swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance next to a

door or under a window. This

prevents hot cookware from falling

from the appliance when the door or

the window is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer is sufficient for

air circulation.

• The bottom of the appliance can get

hot. Install a non-combustible

separation panel under the appliance

to prevent access to the bottom.

2.2 Electrical Connection

WARNING!

Risk of fire and electric

shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation

make sure that the appliance is

disconnected from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect

electricity mains cable or plug (if

applicable) can make the terminal

become too hot.

• Use the correct electricity mains

cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the

cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

ENGLISH 5

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to

the mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have

an isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation

device must have a contact opening

width of minimum 3 mm.

2.3 Gas connection

• All gas connections must be made by

a qualified person.

• Before installation, make sure that the

local distribution conditions (nature of

the gas and gas pressure) and the

adjustment of the appliance are

compatible.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply

is on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current

installation regulations. Follow the

requirements for adequate ventilation.

2.4 Use

WARNING!

Risk of injury, burns and

electric shock.

• Remove all the packaging, labelling

and protective film (if applicable)

before first use.

• This appliance is for household use

only.

• Do not change the specification of this

appliance.

• Make sure that the ventilation

openings are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after

each use.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with wet

hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• When you place food into hot oil, it

may splash.

WARNING!

Risk of fire and explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or

heated objects away from fats and

oils when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause fire at a lower

temperature than oil used for the first

time.

• Do not put flammable products or

items that are wet with flammable

products in, near or on the appliance.

WARNING!

Risk of damage to the

appliance.

• Do not keep hot cookware on the

control panel.

• Do not let cookware boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

www.electrolux.com6

• Never leave a burner on with empty

cookware or without cookware.

• Do not put aluminium foil on the

appliance.

• Cookware made of cast iron,

aluminium or with a damaged bottom

can cause scratches on the glass /

glass ceramic. Always lift these

objects up when you have to move

them on the cooking surface.

• Use only stable cookware with the

correct shape and diameter larger

than the dimensions of the burners.

• Make sure cookware is centrally

positioned on the burners.

• Do not use large cookware that

overlap the edges of the appliance.

This can cause damage to the

worktop surface.

• Make sure the flame does not go out

when you quickly turn the knob from

the maximum to the minimum

position.

• Use only the accessories supplied

with the appliance.

• Do not install a flame diffuser on the

burner.

• The use of a gas cooking appliance

results in the production of heat and

moisture. Provide good ventilation in

the room where the appliance is

installed.

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of a

window, or more effective ventilation,

for example increasing the level of

mechanical ventilation where present.

• This appliance is for cooking

purposes only. It must not be used for

other purposes, for example room

heating.

• Do not let acid liquids, for example

vinegar, lemon juice or limescale

remover, touch the hob. This can

cause matt patches.

• Discoloration of the enamel or

stainless steel has no effect on the

performance of the appliance.

2.5 Care and cleaning

WARNING!

Do not remove the buttons,

knobs or gaskets from the

control panel. Water may get

inside the appliance and

cause damage.

• Clean the appliance regularly to

prevent the deterioration of the

surface material.

• Switch off the appliance and let it cool

down before cleaning.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Use only neutral detergents. Do

not use abrasive products, abrasive

cleaning pads, solvents or metal

objects.

• Do not clean the burners in the

dishwasher.

2.6 Service

• To repair the appliance contact the

Authorised Service Centre. Use

original spare parts only.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

humidity, or are intended to signal

information about the operational

status of the appliance. They are not

intended to be used in other

applications and are not suitable for

household room illumination.

2.7 Disposal

WARNING!

Risk of injury or suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable

close to the appliance and dispose of

it.

• Flat the external gas pipes.

ENGLISH 7

3. INSTALLATION

WARNING!

Refer to Safety chapters.

3.1 Before the installation

Before you install the hob, write down the

information below from the rating plate.

The rating plate is on the bottom of the

hob.

Model .......................................

PNC .........................................

Serial number ...........................

3.2 Gas Connection

WARNING!

The following instructions

about installation,

maintenance and ventilation

must be carried out by

qualified personnel in

compliance with the

regulation in force (UNI-CIG

7129 - 7131). Make sure that

the kitchen is well ventilated:

keep natural ventilation

holes open (at least 100

cm²) or install a mechanical

extractor hood.

Choose fixed connections or use a

flexible pipe in stainless steel in

compliance with the regulation in force. If

you use flexible metallic pipes, be careful

they do not come in touch with mobile

parts or they are not squeezed. Also be

careful when the hob is put together with

an oven.

Make sure that the gas

supply pressure of the

appliance obeys the

recommended values.

If the supplied pressure has not the

specified value, it is necessary to

assemble a proper pressure regulator in

compliance with the standard UNI EN 88.

For Liquid Gas (LPG) the use of pressure

regulator is allowed only if they are in

compliance with UNI EN 12864. The

adjustable connection is fixed to the

comprehensive ramp by means of a

threaded nut G 1/2". Screw the parts

without force, adjust the connection in

the necessary direction and tighten

everything.

A B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Rigid connection:

Carry out connection by using metal rigid

pipes (copper with mechanical end)

(UNI-CIG 7129).

Flexible connection:

Use a flexible pipe in stainless steel

(UNI-CIG 9891) with a maximum length 2

m.

WARNING!

When installation is

complete, make sure that

the seal of each pipe fitting

is correct. Use a soapy

solution, not a flame!

3.3 Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the

type of gas you use (see table in

"Technical Data" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Attach the label with the new type of

gas supply near the gas supply pipe.

You can find this label in the package

supplied with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

www.electrolux.com8

3.4 Adjustment of minimum

level

WARNING!

Information for authorised

installer only.

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob and using thin

screwdriver lift up and remove the

plastic magnet holder.

4. With a thin screwdriver, adjust the

bypass screw position (A).

A

5. If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of

a turn for Multi Crown burner).

6. Reassemble the magnet holder and

the knob.

WARNING!

Make sure the flame does

not go out when you quickly

turn the knob from the

maximum position to the

minimum position.

3.5 Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a

mains cable. It has to be supplied with

a correct plug which can hold the load

that the rating plate rates. Make sure

that you install the plug in a correct

socket.

• Always use a correctly installed

shockproof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• There is a risk of fire when the

appliance is in connection with an

extension cable, an adapter or a

multiple connection. Make sure that

the ground connection agrees with the

standards and regulations.

• Do not let the power cable to heat up

to a temperature higher than 90° C.

To prevent contact between the cable

and the appliance below the hob use the

clamps which are on the side of the

cabinet.

ENGLISH 9

A

A. Rigid copper pipe or flexible pipe of

stainless steel

If the pilot lights turn on after

connecting the hob to the

mains, turn on and off the

control knob and wait until

the residual heat indicator

goes out.

3.6 Connection cable

To replace the connection cable use only

the special cable or its equivalent. The

cable type is: H03V2V2-F T90.

Make sure that the cable section is

applicable to the voltage and the working

temperature. The yellow / green earth

wire must be approximately 2 cm longer

than the brown (or black) phase wire.

L

N

1. Connect the green and yellow (earth)

wire to the terminal which is marked

with the letter 'E', or the earth symbol

, or coloured green and yellow.

2. Connect the blue (neutral) wire to the

terminal which is marked with the

letter 'N' or coloured blue.

3. Connect the brown (live) wire to the

terminal which is marked with the

letter 'L'. It must always be connected

to the network phase.

3.7 Assembly

1.

2.

3.

min. 55 mm

min. 650 mm

830 mm

2

0

+

min. 100 mm

30 mm

480 mm

2

0

+

4.

www.electrolux.com10

5.

6.

B

A

A) supplied seal

B) supplied brackets

7.

CAUTION!

Install the appliance only on

a worktop with flat surface.

3.8 Installing hob under the

hood

If you install the hob under a

hood, please see the

installation instructions of the

hood for the minimum

distance between the

appliances.

3.9 Possibilities for insertion

The panel installed below the hob must

be easy to remove and let an easy

access in case a technical assistance

intervention is necessary.

Kitchen unit with door

min 20 mm

(max 150 mm)

30 mm

60 mm

B

A

A. Removable panel

B. Space for connections

Kitchen unit with oven

The electrical connection of the hob and

the oven must be installed separately for

safety reasons and to let easy remove

oven from the unit.

ENGLISH 11

4. PRODUCT DESCRIPTION

4.1 Cooking surface layout

1

4

6

3

2

5

1

Semi-rapid burner

2

Multi Crown burner

3

Auxiliary burner

4

Control panel

5

Control knobs

6

Window for Hob²Hood infrared signal

4.2 Control panel layout

1

4

2 3

Use the sensor fields to operate the Minute Minder and Hob²Hood. The displays,

indicators and sounds tell which functions operate.

Sensor

field

Function Comment

- To select the Timer function.

To activate

/ and

Hob²Hood icons.

To make the LEDs visible.

- Timer display To show the time in minutes.

To show Hob²Hood function and Hob²Hood Automatic

Modes.

Hob²Hood To activate and deactivate the manual mode of the

function.

www.electrolux.com12

Sensor

field

Function Comment

/

- To increase or decrease the time.

To switch Hob²Hood Automatic Modes.

Stand-by mode:

Press the for at least 1 second to activate the display, and .

4.3 Control knob

Symbol Description

no gas supply / off posi‐

tion

ignition position / maxi‐

mum gas supply

Symbol Description

minimum gas supply

1 - 9 power levels

4.4 Residual heat

8

9

7

6

5

4

3

2

1

8

9

7

6

5

4

3

2

1

LEDs full light

Knob opened

LEDs light slowly reduced

Residual heat starts

LEDs light off

Residual heat ends

WARNING!

There is a risk of burns from

residual heat.

The residual heat indicator

lights up when you turn off

the burner.

Knob of the

burner

Open knob

on < 20 s 20 s < on < 1 min

1 min < on < 5

min

on > 5 min

Multi Crown 0 30 sec 3 min 15 min

Semi-rapid

(front left)

0 30 sec 3 min 10 min

Semi-rapid

(rear left)

0 30 sec 3 min 10 min

ENGLISH 13

Semi-rapid

(rear right)

0 30 sec 3 min 10 min

Auxiliary 0 30 sec 3 min 5 min

5. DAILY USE

WARNING!

Refer to Safety chapters.

5.1 Burner overview

$

%

'

&

$

%

'

&

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

5.2 Ignition of the burner

Always light the burner

before you put on the

cookware.

WARNING!

Be very careful when you

use open fire in the kitchen

environment. The

manufacturer declines any

responsibility in case of the

flame misuse.

1. Push the control knob down and turn

it counterclockwise to the maximum

gas supply position ( ).

2. Keep the control knob pushed for

equal or less than 10 seconds. This

lets the thermocouple warm up. If

not, the gas supply is interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner

does not light, check if the

crown and its cap are in

correct positions.

WARNING!

Do not keep the control knob

pushed for more than 15

seconds. If the burner does

not light after 15 seconds,

release the control knob,

turn it into off position and try

to light the burner again after

minimum 1 minute.

www.electrolux.com14

CAUTION!

In the absence of electricity

you can ignite the burner

without electrical device; in

this case approach the

burner with a flame, turn the

control knob counter-

clockwise to maximum gas

supply position and push it

down. Keep the control knob

pushed for equal or less

than 10 seconds to let the

thermocouple warm up.

If the burner accidentally

goes out, turn the control

knob to the off position and

try to light the burner again

after minimum 1 minute.

The spark generator can

start automatically when you

switch on the mains, after

installation or a power cut. It

is normal.

Each control knob is

surrounded by highlighted

numbers visible while

Residual Heat function

operates.

The hob is supplied with

StepPower. This function

allows you to set the power

more precisely from 9-1.

WARNING!

If you do not switch the knob

to the off position, after two

hours a warning sound is

emitted and the symbols

flash red. It reminds you that

the burner is on. To stop the

sound, touch , , or

.

5.3 Turning the burner off

To put the flame out, turn the knob to the

off position .

WARNING!

Always turn the flame down

or switch it off before you

remove the pans from the

burner.

5.4 Minute Minder

You can use this function as a Minute

Minder.

The Minute Minder is the only icon visible

in standby state. Touch the

to activate

other icons.

1. Touch

.

To activate the function.

2. Touch or of the timer to set the

time (00 - 99 minutes).

When the time comes to an end, the

sound operates and 00 flashes.

In the last minute the time

decreases in seconds, and

the last 10 seconds the timer

emits a sound signal.

3.

Touch , , or .

To stop the sound.

4. To stop the timer, touch longer .

You can use the Minute

Minder at any time also if the

appliance is off.

The function has no effect

on the operation of the

burners.

5.5 Hob²Hood

It is an advanced automatic function

which connects the hob to a special

hood. Both the hob and the hood have

an infrared signal communicator. You

can also operate the fan from the hob

manually.

Manual modes:

Mode Manual

light

Fan speed

H0 Off Off

HL On Off

ENGLISH 15

Mode Manual

light

Fan speed

H1 On Level 1

H2 On Level 2

H3 On Level 3

To turn off the hood touch

longer till H0 is displayed.

WARNING!

After end of cooking, the

hood does not turn off

automatically. Turn it off

manually.

For most of the hoods, the

remote system is originally

deactivated. Activate it

before you use the function.

For more information refer to

the hood user manual.

Setting default Hob²Hood procedure:

1. When timer is off, touch Minute

Minder for 3 seconds.

00, and come on.

2. Touch and together until An

comes on, n is a current automatic

mode.

3. Touch

to select desired automatic

mode.

After the Automatic Mode is selected,

wait till it disappears from the display so

that this setting is saved in Flash Memory

and recalled at startup.

Repeat the same procedure

to select another Hob²Hood

Automatic Mode.

Automatic modes:

Mode Description H2H icon H2H display Automatic

light

Fan speed

A0 No remote control Off Off Off Off

A1 Remote control On On Off Off

A2 H2H Auto Light On On On Off

A3 H2H Auto Speed 0-2

(factory default)

On On On 1

A4 H2H Auto Speed 1-3 On On On 1-3

A3

Burner type on Speed

AUX 1

SR 1

MC 1

A4

Power (kW) Speed

A4

1-5 1

6-8 2

9-11 3

www.electrolux.com16

6. HINTS AND TIPS

WARNING!

Refer to Safety chapters.

6.1 Cookware

CAUTION!

Do not use cast iron pans,

clay or earthenware pots,

grilling accessories or

toaster plates.

WARNING!

Do not put the same pan on

two burners.

WARNING!

Do not put unstable or

damaged pots on the burner

to prevent spills and injuries.

CAUTION!

Make sure that the bottoms

of pots do not stand too

close to the control knob,

otherwise the flame heats

the control knob up.

CAUTION!

Make sure that pot handles

are not above the front edge

of the cooktop.

CAUTION!

Make sure that the pots are

placed centrally on the

burner in order to get the

maximum stability and a

lower gas consumption.

CAUTION!

Liquids spilt during cooking

can cause the glass to

break.

6.2 Diameters of cookware

CAUTION!

Use cookware with

diameters applicable to the

size of burners.

Burner Diameter of

cookware

(mm)

Multi Crown 180 - 260

Semi-rapid (rear left) 120 - 240

Semi-rapid (rear right) 120 - 240

Semi-rapid (front left) 120 - 240

Auxiliary 80 - 180

6.3 Hints and Tips for

Hob²Hood

When you operate the hob with the

function:

• Protect the hood panel from direct

sunlight.

• Do not spot halogen light on the hood

panel.

• Do not cover the hob control panel.

• Do not interrupt the signal between

the hob and the hood (e.g. with the

hand, a cookware handle or a tall

pot). See the picture.

The hood in the picture is only

exemplary.

Keep the window for

Hob²Hood infrared signal

communicator clean.

ENGLISH 17

Other remotely controlled

appliances may block the

signal. Do not use any such

appliances near to the hob

while Hob²Hood is on.

Cooker hoods with the Hob²Hood

function

To find the full range of cooker hoods

which work with this function refer to our

consumer website. The Electrolux cooker

hoods that work with this function must

have the symbol .

6.4 Suggested recipes

Food categories Recipes Burner type Power level

Sauces - Dressing

Bechamel Auxiliary 2-4

Tomato sauce Semi-rapid 1-5

Pasta - Rice - other

Cereals

Mushrooms rice Multi Crown 1-5

Couscous Rapid 1-6

Ravioli Auxiliary 6-9

Soup - Legumes

Vegetable soup Semi-rapid 2-7

Mushrooms and pota‐

toes soup

Semi-rapid 1-5

Fish soup Multi Crown 1-4

Meat

Beef meatballs Multi Crown 1-6

Fillet of pork roast Multi Crown 4-9

Beef burger gratin Auxiliary 1-5

Fish

Sepia with peas Multi Crown 1-5

Roasted tuna steak Rapid 5-8

Eggs based meals Omelette Multi Crown 1-5

Vegetables

Mushrooms with sea‐

sonings

Semi-rapid 2-6

Caponata with vegeta‐

bles

Multi Crown 4-8

Frozen spinach with

butter

Rapid 1-4

Fried dishes

French fries Multi Crown 5-9

Donuts Multi Crown 3-7

Snacks cooked with

pan

Roasting nuts Semi-rapid 2-5

Croutons of bread Multi Crown 2-7

Pancakes Semi-rapid 3-9

www.electrolux.com18

Food categories Recipes Burner type Power level

Desserts

Caramel Auxiliary 1-5

Custard Auxiliary 1-5

Panna cotta Auxiliary 1-5

All recipes for approximately

4 portions.

The settings suggested in

the cooking table should

only serve as guidelines and

be adjusted depending on

the rawness of food, its

weight and quantity as well

as on the type of gas used

and the material of the

cookware used to prepare

the dish.

For an optimal delicate

cooking use the auxiliary

burner.

7. CARE AND CLEANING

WARNING!

Refer to Safety chapters.

7.1 General information

• Clean the hob after each use.

• Clean the hob when all light are off.

The Minute Minder may stay

activated.

• Always use cookware with a clean

base.

• Use a special cleaner suitable for the

surface of the hob.

• Wash stainless steel parts with water,

and then dry them with a soft cloth.

• Scratches or dark stains on the

surface have no effect on how the hob

operates.

The presence of water or

other liquids on the control

panel can accidentally

activate or deactivate the

hob functions.

WARNING!

Do not use knives, scrapers

or similar instruments to

clean the surface of the

glass or the rims of the

burners and the frame (if

applicable).

7.2 Pan supports

The pan supports are not

resistant to washing in a

dishwasher. They must be

washed by hand.

1. Remove the pan supports to easily

clean the hob.

Be very careful when

you replace the pan

supports to prevent the

hob top from damage.

2. The enamel coating occasionally can

have rough edges, so be careful

when you wash the pan supports by

hand and dry them. If necessary,

remove stubborn stains with a paste

cleaner.

ENGLISH 19

3. After you clean the pan supports,

make sure that they are in correct

positions.

4. For the burner to operate correctly,

make sure that the arms of the pan

supports are aligned with the centre

of the burner inserted in the recesses

of the enamelled plates.

7.3 Removing and assembling

pan supports

After cleaning of the hob, make sure that

pan supports are in a correct position. In

order to place a pan support properly,

make sure that its arms fits the cut-outs

placed at the base of the burner as

shown in the picture. This way, a pan

support is stable and fixed.

7.4 Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, sugar and food with sugar,

otherwise, the dirt can cause damage

to the hob. Take care to avoid burns.

• Remove when the hob is

sufficiently cool: limescale rings,

water rings, fat stains, shiny metallic

discoloration. Clean the hob with a

moist cloth and a non-abrasive

detergent. After cleaning, wipe the

hob dry with a soft cloth.

• To clean the enamelled parts, caps

and crowns, wash them with warm

soapy water and dry them carefully

before you put them back on.

7.5 Cleaning the spark plug

This feature is obtained through a

ceramic ignition candle with a metal

electrode. Keep these components well

clean to prevent difficult lighting and

check that the burner crown holes are

not obstructed.

7.6 Periodic maintenance

Speak to your local Authorised Service

Centre periodically to check the

conditions of the gas supply pipe and the

pressure adjuster, if fitted.

8. TROUBLESHOOTING

WARNING!

Refer to Safety chapters.

8.1 What to do if...

Problem Possible cause Remedy

There is no spark when

you try to activate the

spark generator.

The hob is not connected

to an electrical supply or it

is connected incorrectly.

Check if the hob is correct‐

ly connected to the electri‐

cal supply.

The fuse is blown. Make sure that the fuse is

the cause of the malfunc‐

tion. If the fuse is blown

again and again, contact a

qualified electrician.

www.electrolux.com20

La page charge ...

Electrolux KGG95375K Manuel utilisateur

Electrolux KGG95375K Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents