Ariston RPG 822 S EX Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
RPG 822
English,1
GB
Français,13
FR
AR
, 25
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls,
furniture cabinets or anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness
by tightening or
loosening the
adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose
extensions; if it is absolutely necessary, the
extension must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple
sockets.
! The cable should not be bent or
compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle number auto clean (see “Cleaning
the washing machine”).
Technical data
Model
RPG 822
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity
from 1 to 8 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 9
;
Eco Cotton
60°/4
(60°).
programme 9
;
Eco Cotton
60°/4
(40°).
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cutting off the water and
electricity supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to
prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasaautoclean
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10%
the quantity specified
for lightly-soiled
garments) or special
additives to clean the
washing machine. We
recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
1
2
A
B
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washing machine
(see figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
button
OPTION
buttons and
indicator lights
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
Programme Key: the Programme Key inside the
detergent dispenser shows all the available programmes
together with a graphical guide on how to use the
individual dispenser compartments.
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION buttons and indicator lights: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION
button and indicator light : to
select the desired wash intensity.
TEMPERATURE button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAY button: press to set a delayed start for the
selected wash cycle; the delay period appears on the
display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
KEY LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the symbol is illuminated, the control panel
is locked (apart from the ON/OFF button). This means it
is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the
home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Antimicrobial seal
The seal around the porthole door is made from a special
mixture ensuring antimicrobial protection, thus reducing
bacterial proliferation up to 99.99%.
The seal contains zinc pyrithione, a biocidal substance
which reduces the proliferation of harmful microbes (*)
such as batteries and mould prone to causing stains,
unpleasant odours and product deterioration.
(*) According to tests performed by the University of Perugia,
Italy on: Staphylococcus aureus, Escherichia coll, Pseudomonas
aeruginosa, Candida albicans, Aspergillus niger, Penicillium digitatum.
In rare cases an allergic reaction may be caused by prolonged contact between
seal and skin.
KEY
LOCK
button
CLEANING
ACTION
button and
indicator light
Programme
Key
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A (the display will show
the maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the
programme varies depending on the wash load and the settings chosen); if the DELAY option has been set, the countdown
to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Pump out
The icons corresponding to “temperature”, “spin” and “delayed start” (working from the left) are displayed in section C.
The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle.
The “spin” bars indicate the maximum spin level which may be selected for the set cycle.
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
B
C
A
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the selected
cycle, or the most recently-used settings if they are
compatible with the selected cycle. The temperature
can be decreased by pressing the button, until
the cold wash “OFF” setting is reached. The spin
speed may be progressively reduced by pressing
the button, until it is completely excluded (the
“OFF” setting). If these buttons are pressed again, the
maximum values are restored.
! Exception: if the 3 programme is selected, the
temperature can be increased up to a value of 90°C.
! Exception: if the 4 programme is selected, the
temperature can be increased up to a value of 60°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment (3). When
pouring in the bleach, be careful not to exceed the
“max” level marked on the central pivot (see figure pag.
10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will
be activated; the indicator light for the option which has
been activated will be illuminated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option will
not be activated.
! If the selected option is not compatible with a previously
selected one, the indicator light corresponding to the first
function selected will flash and only the second option will be
activated; the indicator light for the option which has been
activated will be illuminated.
Extra Rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
Table of programmes and wash cycles
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
40°C . The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set programme 9 at temperature 40°C.
3) Long wash cycle for synthetics: set wash cycle 4 with a temperature of 40°C.
Time Saver
If you select this option, the wash cycle duration will be
reduced by up to 50%, depending on the selected cycle,
thereby guaranteeing simultaneous water and energy
saving. Use this cycle for lightly soiled garments.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumptionkWh
Total water lt
Cycle dura-
tion
Wash
Fabric
softener
Bleach
DAILY CLEAN
1
Anti Stain
40° 1200
- 5 - - -
**
2
Anti Stain Quick
40° 1200
- 4,5 - - -
**
3
Cotton: lightly soiled resistant and delicate colours.
40°
(Max. 90°C)
1200
8 - - -
**
4
Synthetics (3): lightly soiled resistant colours.
40°
(Max. 60°C)
1000
4,5 46 0,56 65 100’
5
Fast 30’: to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800
- 3,5 71 0,20 38 30’
SPECIALS
6
Darks
30° 800
- 5 - - -
**
7
Ultadelicates
30° 0
- 1 - - -
**
8
Wool: for wool, cashmere, etc.
40° 800
- 2 - - -
**
9
Eco Cotton
60°/4
(1): heavily soiled whites and resistant colours.
60°
1200
- 8 53 1,23 55 195’
9
Eco Cotton
60°/4
(2): lightly soiled resistant and delicate colours.
40°
1200
- 8 53 1,01 92 180’
10
Cotton 2C: lightly soiled resistant and delicate colours.
20°
1200
8 - - -
**
EXTRA
11
Baby
40° 1000
5 - - -
**
12
Anti Allergy
60°
1200
5 - - -
**
13
Silk & Curtains: for garments in silk and viscose, lingerie. 30° 0
- 2 - - -
**
14
Duvets: for down-stuffed garments. 30° 1000
- 3,5 - - -
**
Partial Programmes
Rinse
-
1200 -
- 8 - - -
**
Spin + Pump out
-
1200 - - - 8 - - -
**
Pump out only *
- OFF
- - - 8 - - -
**
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
! Do not pour detergent into
the middle compartment (*).
compartment 1:
Detergent for the wash
cycle (powder or liquid)
If liquid detergent is used,
it is recommended that the removable plastic partition A
(supplied) be used for proper dosage. If powder detergent
is used, place the partition into slot B.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 3: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichreferto
the weight of the laundry when dry: see “Table of
programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing class
that is higher than the standard class (A class). When running
the programme, do not mix garments of different colours. We
recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are obstinate stains.
Anti Stain Quick: this programme is ideal for washing the
most difficult daily stains in 1 hour. It is ideal for mixed fabrics
and coloured garments, caring for your clothes as it washes.
Darks: use cycle 6 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
Ultradelicates: use programme 7 to wash very delicate
garments having strasses or sequins.
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
M
AX
1
3
2
A
B
*
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine (M1127)
Cotton 20°C: the programme 10 ideal for lightly soiled
cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Baby: use the special wash cycle 11 to remove the
remove the soiling typically caused by babies, while
removing all traces of detergent from nappies in order to
prevent the delicate skin of babies from suffering allergic
reactions. The cycle has been designed to reduce the
amount of bacteria by using a greater quantity of water
and optimising the effect of special disinfecting additives
added to the detergent.
Anti Allergy: use programme 12 to remove major
allergens such as pollen, mites, cat’s and dog’s hair.
Silk: use special wash cycle 13 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case
or mesh bag. Use wash cycle 13.
Duvets: to wash double or single duvets (the weight of
which should not exceed 3,5 kg), cushions or clothes
padded with goose down such as puffa jackets, use
the special 14 wash cycle. We recommend that duvets
are placed in the drum with their edges folded inwards
(see figure) and that no more than ¾ of the total volume
of the drum is used. To achieve the best results, we
recommend that a liquid detergent is used and placed
inside the detergent dispenser drawer.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The “option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”);
• Restartthewashcycletocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
FR
13
Français
FR
LAVE-LINGE
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Entretien et soin, 16
Coupure de l’arrivée d’eau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Précautions et conseils, 17
Sécurité générale
Mise au rebut
Ouverture manuelle du hublot
Description du lave-linge, 18-19
Bandeau de commandes
Écran
Comment faire un cycle de lavage, 20
Programmes et options, 21
Tableau des programmes
Options de lavage
Produits lessiviels et linge, 22
Tiroir à produits lessiviels
Triage du linge
Programmes spéciaux
Système d’équilibrage de la charge
Anomalies et remèdes, 23
Assistance, 24
RPG 822
Mode d’emploi
14
FR
Installation
! Conserver ce mode d’emploi pour pouvoir
le consulter à tout moment. En cas de vente,
de cession ou de déménagement, veiller à
ce qu’il suive toujours le lave-linge pour que
son nouveau propriétaire soit informé sur son
mode de optionnement et puisse profiter des
conseils correspondants.
! Lire attentivement les instructions: elles
fournissent des conseils importants sur
l’installation, l’utilisation et la sécurité de
l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été
endommagé pendant le transport. S’il est
abîmé, ne pas le raccorder et contacter le
vendeur.
3. Enlever les 4 vis
de protection servant
au transport, le
caoutchouc et la cale,
placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons
plastique fournis.
5. Conserver toutes ces pièces: il faudra les
remonter en cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des
jouets pour enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide,
sans l’appuyer contre des murs, des meubles
ou autre.
2. Si le sol n’est
pas parfaitement
horizontal, visser ou
dévisser les pieds de
réglage avant (voir
figure) pour niveler
l’appareil; son angle
d’inclinaison, mesuré
sur le plan de travail, ne
doit pas passer 2°.
Une bonne mise à niveau garantit la stabilité
de l’appareil et évite qu’il y ait des vibrations,
du bruit et des déplacements en cours de
optionnement. Si la machine est posée sur de
la moquette ou un tapis, régler les pieds de
manière à ce qu’il y ait suffisamment d’espace
pour assurer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de
l’eau
1. Reliez le tuyau
d’alimentation en le
vissant à un robinet
d’eau froide à embout
fileté 3/4 gaz (voir
figure).
Faire couler l’eau
jusqu’à ce qu’elle
soit limpide et sans
impuretés avant de
raccorder.
2. Raccorder le tuyau
d’arrivée de l’eau
au lave-linge en le
vissant à la prise
d’eau prévue, dans la
partie arrière en haut
à droite (voir figure).
3. Attention à ce que le tuyau ne soit pas plié
ou écrasé.
! La pression de l’eau doit être comprise entre
les valeurs indiquées dans le tableau des
Caractéristiques techniques (voir page ci-
contre).
! Si la longueur du tuyau d’alimentation ne
suffit pas, s’adresser à un magasin spécialisé
ou à un technicien agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
FR
15
Raccordement du tuyau de vidange
Raccorder le tuyau
d’évacuation, sans
le plier, à un conduit
d’évacuation ou
à une évacuation
murale placés à
une distance du sol
comprise entre 65 et
100 cm ;
ou bien l’accrocher
à un évier ou à une
baignoire, dans ce
cas, fixer le support
en plastique fourni
avec l’appareil au
robinet (voir figure).
L’extrémité libre du
tuyau d’évacuation
ne doit pas être
plongée dans l’eau.
! L’utilisation d’un tuyau de rallonge est
absolument déconseillée mais si on ne peut
faire autrement, il faut absolument qu’il ait le
même diamètre que le tuyau original et sa
longueur ne doit pas dépasser 150 cm.
Raccordement électrique
Avant de brancher la fiche dans la prise de
courant, s’assurer que :
• lapriseestbienreliéeàlaterreetest
conforme aux réglementations en vigueur;
• lapriseestbienapteàsupporterla
puissance maximale de l’appareil indiquée
dans le tableau des Caractéristiques
techniques (voir ci-contre);
• latensiond’alimentationestbiencomprise
entre les valeurs figurant dans le tableau
des Caractéristiques techniques (voir ci-
contre);
• lapriseestbiencompatibleaveclafichedu
lave-linge. Autrement, remplacer la prise ou
la fiche.
! Le lave-linge ne doit pas être installé dehors,
même à l’abri, car il est très dangereux de le
laisser exposé à la pluie et aux orages.
! Après installation du lave-linge, la prise de
courant doit être facilement accessible.
! N’utiliser ni rallonges ni prises multiples.
65 - 100 cm
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé
que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité
en cas de non-respect des normes
énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil,
effectuer un cycle de lavage avec un produit
lessiviel mais sans linge et sélectionner le
programme auto nettoyage (voir “Nettoyage
du lave-linge”).
Caractéristiques techniques
Modèle
RPG 822
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 60,5 cm
Capacité
de 1 à 8 kg
Raccorde-
ments élec-
triques
Voir la plaque signalétique
appliquée sur la machine
Raccor-
dements
hydrauli-
ques
pression maximale
1 MPa (10 bar)
pression minimale
0,05 MPa (0,5 bar)
capacité du tambour 62 litres
Vitesse
d'essorage
jusqu'à 1200 tours minute
Programmes
de contrôle
selon les
directives
1061/2010
1015/2010
programme 9;
Coton Eco
60°/4
(60°).
programme 9;
Coton Eco
60°/4
(40°).
Cet appareil est conforme
aux Directives Communau-
taires suivantes:
- 2004/108/CE (Compatibili-
té électromagnétique)
- 2012/19/EU (WEEE)
- 2006/95/CE (Basse Tension)
16
FR
Entretien et soin
Coupure de l’arrivée d’eau et du
courant
•Fermerlerobinetdel’eauaprèschaque
lavage. Cela réduit l’usure de l’installation
hydraulique du lave-linge et évite tout danger
de fuites.
•Débrancherlafichedelaprisedecourantlors
de tout nettoyage du lave-linge et pendant
tous les travaux d’entretien.
Nettoyage du lave-linge
•Pournettoyerl’extérieuretlespartiesen
caoutchouc, utiliser un chiffon imbibé d’eau
tiède et de savon. N’utiliser ni solvants ni
abrasifs.
•Celave-lingeestéquipéd’unprogramme
auto nettoyage des parties internes qui doit
être effectué tambour complètement vide.
La lessive (dans une quantité égale à 10% de
celle conseillée pour du linge peu sale) ou les
additifs spéciaux pour le nettoyage du lave-
linge, pourront être utilisés comme adjuvants
dans le programme de lavage. Il est conseillé
d’effectuer le programme de nettoyage tous
les 40 cycles de lavage.
Pour activer le
programme, appuyer
simultanément sur
les touches A et B
pendant 5 secondes
(voir figure).
Le programme
démarrera
automatiquement
et durera environ 70
minutes. Pour stopper le cycle, appuyer sur la
touche MARCHE/PAUSE.
Nettoyage du tiroir à produits
lessiviels.
Soulever le tiroir et le tirer vers soi pour le sortir
de son logement (voir
figure).
Le laver à l’eau
courante; effectuer
cette opération assez
souvent.
Entretien du hublot et du tambour
•Ilfauttoujourslaisserlehublotentrouvert
pour éviter la formation de mauvaise odeurs.
Nettoyage de la pompe
Le lave-linge est équipé d’une pompe
autonettoyante qui n’exige aucune opération
d’entretien. Il peut toutefois arriver que de
menus objets (pièces de monnaie, boutons)
tombent dans la préchambre qui protège la
pompe, placée en bas de cette dernière.
! S’assurer que le cycle de lavage est bien
terminé et débrancher la fiche.
Pour accéder à cette préchambre:
1. démonter le panneau situé à l’avant du
lave-linge à l’aide d’un tournevis (voir figure);
2. dévisser le
couvercle en le
tournant dans le sens
inverse des aiguilles
d’une montre (voir
figure): il est normal
qu’un peu d’eau
s’écoule;
3. nettoyer
soigneusement
l’intérieur;
4. revisser le
couvercle;
5. remonter le panneau en veillant à bien
enfiler les crochets dans les fentes prévues
avant de le pousser contre l’appareil.
Contrôle du tuyau darrivée de l’eau
Contrôler le tuyau d’alimentation au moins
une fois par an. Procéder à son remplacement
en cas de craquèlements et de fissures: car
les fortes pressions subies pendant le lavage
pourraient provoquer des cassures.
! N’utiliser que des tuyaux neufs.
1
2
A
B
FR
17
ou leur revendeur concernant la démarche à suivre pour
l’enlèvement de leur vieil appareil.
Ouverture manuelle du hublot
A défaut de pouvoir ouvrir la porte hublot à cause d’une
panne de courant pour étendre le linge, procéder comme
suit :
1. débrancher la fiche de la
prise de courant.
2. s’assurer que le niveau de
l’eau à l’intérieur de l’appareil
se trouve bien au-dessous
de l’ouverture du hublot, si
ce n’est pas le cas vider l’eau
en excès à travers le tuyau
de vidange dans un seau
comme illustré voir figure.
3. démonter le panneau situé
à l’avant du lave-linge à l’aide
d’un tournevis (voir figure).
4. se servir de la languette indiquée, tirer vers soi jusqu’à
ce que le tirant en plastique se dégage de son cran d’arrêt;
tirer ensuite vers le bas et ouvrir l’hublot en même temps.
5. remonter le panneau en veillant à bien enfiler les
crochets dans les fentes prévues avant de le pousser
contre l’appareil.
Précautions et conseils
20
! Ce lave-linge a été conçu et fabriqué conformément
aux normes internationales de sécurité. Ces consignes
sont fournies pour des raisons de sécurité, il faut les lire
attentivement.
Sécurité générale
• Cetappareilestconçupourunusagedomestique.
•Cet appareil peut être utilisé par les enfants à
partir de 8 ans et par les personnes dont les
capacités physiques, sensorielles ou mentales
sont réduites ou qui ne disposent pas des
connaissances suffisantes, à condition qu’ils
soient encadrés ou aient été formés de façon
appropriée pour l’utilisation de l’appareil de
façon sûre et en comprenant les dangers qui
y sont liés. Les enfants ne doivent pas jouer
avec l’appareil. L’entretien et le nettoyage
ne doivent pas être effectués par les enfants
sans surveillance.
• Nejamaistoucherl’appareilsil’onestpiedsnusetsiles
mains sont mouillées ou humides.
• Nejamaistirersurlecâblepourdébrancherlafichedela
prise de courant.
• Nepasouvrirletiroiràproduitslessivielssilamachine
est branchée.
• Nepastoucheràl’eaudevidange,ellepeutatteindre
des températures très élevées.
• Nepasforcerpourouvrirlehublot:leverrouillagede
sécurité qui protège contre les ouvertures accidentelles
pourrait s’endommager.
• Encasdepanne,éviteràtoutprixd’accéderaux
mécanismes internes pour tenter une réparation.
• Veilleràcequelesenfantsnes’approchentpasde
l’appareil pendant son fonctionnement.
• Pendantlelavage,lehublotatendanceàseréchauffer.
• Deuxoutroispersonnessontnécessairespourdéplacer
l’appareil avec toutes les précautions nécessaires. Ne
jamais le déplacer tout seul car il est très lourd.
• Avantd’introduirelelinge,s’assurerqueletambourest
bien vide.
Mise au rebut
• Miseaurebutdumatérield’emballage:seconformer
aux réglementations locales de manière à ce que les
emballages puissent être recyclés.
• LaDirectiveEuropéenne2012/19/EUsurlesDéchets
des Equipements Electriques et Electroniques, exige
que les appareils ménagers usagés ne soient pas
jetés dans le flux normal des déchets municipaux. Les
appareils usagés doivent être collectés séparément afin
d’optimiser le taux de récupération et le recyclage des
matériaux qui les composent et réduire l’impact sur la
santé humaine et l’environnement. Le symbole de la
‘’poubelle barrée’’ est apposée sur tous les produits
pour rappeler les obligations de collecte séparée. Les
consommateurs devront contacter les autorités locales
18
FR
Description du lave-linge
Bandeau de commandes
Touche
TEMPÉRATURE
BOUTON
PROGRAMMES
Tiroir à produits lessiviels
Touche ON/OFF
Touche
ESSORAGE
Touche et voyant
MARCHE/PAUSE
Ecran
Touche
DÉPART DIFFÉRÉ
Touches et voyants
OPTION
Tiroir à produits lessiviels : pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Légende: à l’intérieur du tiroir à produits lessiviels se
trouve la légende qui résume tous les programmes
disponibles, ainsi qu’un guide graphique expliquant
comment utiliser les différents bacs du tiroir.
Touche ON/OFF : appuyer brièvement sur la touche
pour allumer ou éteindre l’appareil. Le voyant vert
MARCHE/PAUSE clignotant lentement indique que la
machine est allumée. Pour éteindre le lave-linge en cours
de lavage, appuyer sur la touche pendant au moins 3
secondes de suite ; une pression brève ou accidentelle
n’entraîne pas l’arrêt de l’appareil. L’arrêt de l’appareil
pendant un lavage annule le lavage en cours.
BOUTON PROGRAMMES: pour sélectionner le
programme désiré (voir “Tableau des programmes”).
Touches et voyants OPTION: pour sélectionner les
options disponibles. Le voyant correspondant à l’option
sélectionnée restera allumé.
Touche
INTENSITE DE LAVAGE
: appuyer pour
sélectionner l’intensité de lavage désirée.
Touche TEMPÉRATURE : appuyer sur cette
touche pour diminuer la température ou pour l’exclure
complètement. La valeur correspondante s’affiche à l’écran.
Touche ESSORAGE : appuyer sur cette touche
pour diminuer la vitesse de l’essorage ou pour l’exclure
complètement. La valeur correspondante s’affiche à l’écran.
Touche DÉPART DIFFÉRÉ : appuyer pour
sélectionner un départ différé pour le programme choisi.
Le retard est affiché à l’écran.
Touche avec voyant MARCHE/PAUSE: quand le
voyant vert clignote lentement, appuyer sur la touche
pour démarrer un lavage. Une fois le cycle lancé, le
voyant passe à l’allumage fixe. Pour activer une pause
de lavage, appuyer à nouveau sur la touche ; le voyant
passe à l’orange et se met à clignoter. Si le symbole
n’est pas allumé, il est possible d’ouvrir le hublot. Pour
faire redémarrer le lavage exactement à l’endroit de l’arrêt,
appuyer une nouvelle fois sur la touche.
Touche VERROU ENFANT: pour activer le verrouillage
des commandes, garder la touche enfoncée pendant
environ 2 secondes. Le symbole allumé indique que le
bandeau de commandes est verrouillé. Ceci permet d’éviter
toute modification involontaire des programmes (exception
faite de la touche ON/OFF), surtout s’il y a des enfants à la
maison. Pour désactiver le verrouillage des commandes,
garder la touche enfoncée pendant environ 2 secondes.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est
équipée d’un système d’extinction automatique (veille)
activé après 30 environ minutes d’inutilisation. Appuyez
brièvement sur la touche ON-OFF et attendre que la
machine soit réactivée.
Joint antimicrobien
Le joint du hublot est réalisé dans un mélange particulier
en mesure de garantir une protection antimicrobienne, en
réduisant la prolifération bactérienne jusqu’à 99,99%.
Le joint du hublot contient du pyrithione de zinc, une
substance biocide qui réduit la prolifération de microbes
nocifs (*) tels que les bactéries et les moisissures, qui
pourraient causer des taches, de mauvaises odeurs et une
détérioration du produit.
(*) Selon le test effectué par l’Université de Perugia sur:
Staphylococcus aureus, Escherichia coll, Pseudomonas
aeruginosa, Candida albicans, Aspergillus niger, Penicillium
digitatum.
Dans de rares cas, le contact prolongé avec le joint peut
provoquer une réaction allergique au niveau de la peau.
Touche
VERROU ENFANT
Touche
INTENSITE
DE LAVAGE
Légende
FR
19
Ecran
B
C
A
L’écran est utile pour programmer la machine et fournit de multiples renseignements.
La section A affiche la durée des différents programmes disponibles et, une fois le cycle lancé, le temps restant jusqu’à la fin
du programme (l’écran affiche la durée maximale du cycle sélectionné, cette dernière pourra diminuer au bout de quelques
minutes car la durée effective du programme varie selon la charge de linge et les sélections effectuées); si un DÉPART
DIFFÉRÉ a été sélectionné, le temps restant avant le démarrage du programme sélectionné est affiché.
De plus, en appuyant sur la touche correspondante, il y a affichage des valeurs maximales de la vitesse d’essorage et de la
température que la machine peut effectuer en fonction du programme sélectionné ou des dernières valeurs sélectionnées si
ces dernières sont compatibles avec le programme sélectionné.
La section B affiche les “phases de lavage” prévues pour le cycle sélectionné et, une fois le programme lancé, la “phase de
lavage” en cours :
Lavage
Rinçage
Essorage
Vidange
La section C contient, en partant de gauche, les icônes correspondant à la “température”, à “l’essorage” et au “Départ
différé”.
Les barres “température” indiquent le niveau de température correspondant au niveau maximum programmable pour
le cycle sélectionné.
Les barres “essorage” indiquent le niveau d’essorage correspondant au niveau maximum programmable pour le cycle
sélectionné.
Le symbole “DÉPART DIFFÉRÉ” s’éclaire pour signaler que l’écran est en train d’afficher le “Départ différé” sélectionné.
Voyant HUBLOT VERROUILLÉ
Le symbole allumé indique que le hublot est verrouillé. Pour éviter d’abîmer l’appareil, attendre que le symbole s’éteigne
avant d’ouvrir le hublot.
Pour ouvrir la porte tandis qu’un cycle est en cours, appuyer sur la touche MARCHE/PAUSE; si le symbole HUBLOT
VERROUILLÉ est éteint, on peut ouvrir le hublot.
20
FR
Comment faire un cycle de lavage
1. METTRE L’APPAREIL SOUS TENSION. Appuyer
sur la touche ; le voyant de MARCHE/PAUSE passe
au vert et clignote lentement.
2. CHARGER LE LINGE. Ouvrir la porte hublot. Charger
le linge en faisant attention à ne pas dépasser la
quantité indiquée dans le tableau des programmes de la
page suivante.
3. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir et
placer le produit lessiviel dans les bacs correspondants
comme indiqué au paragraphe “Produits lessiviels et
linge”.
4. FERMER LE HUBLOT.
5. CHOISIR LE PROGRAMME. Sélectionner à l’aide
du bouton PROGRAMMES le programme voulu; une
température et une vitesse d’essorage pouvant être
modifiées sont associées à ce dernier. La durée du
cycle s’affiche sur l’écran.
6. PERSONNALISER LE CYCLE DE LAVAGE.
Appuyer sur les touches correspondantes :
Modifier la température et/ou l’essorage.
L’appareil affiche automatiquement la température
et l’essorage maximum prévus pour le programme
sélectionné ou ceux qui ont été sélectionnés en
dernier s’ils sont compatibles avec le programme
choisi. Par pression sur la touche on peut diminuer
progressivement la température de lavage jusqu’à un
lavage à froid “OFF”. Par pression sur la touche on
peut diminuer progressivement la vitesse d’essorage
jusqu’à sa suppression totale “OFF”. Une autre pression
sur les touches ramènera les valeurs aux maximales
prévues.
! Exception: lors de la sélection du programme 3 la
température peut être augmentée jusqu’à 90°.
! Exception: lors de la sélection du programme 4 la
température peut être augmentée jusqu’à 60°.
Sélectionner un départ différé.
Pour programmer le départ différé d’un programme
sélectionné, appuyer sur la touche correspondante
jusqu’à ce que le retard désiré soit atteint. Quand cette
option est activée, le symbole s’éclaire sur l’écran.
Pour supprimer le départ différé, appuyer sur la touche
jusqu’à ce que l’écran affiche “OFF”.
Programmer l’intensité de lavage désirée.
L’option permet d’optimiser le lavage selon le degré
de salissure des tissus et l’intensité de lavage désirée.
Pour du linge très sale, appuyer sur la touche
jusqu’à ce que le niveau «Intensive» soit atteint. Ce
niveau permet d’obtenir un lavage très performant car
l’utilisation d’une plus grande quantité d’eau au cours
de la phase initiale du cycle et un brassage mécanique
plus intense permettent d’éliminer les taches les plus
difficiles; possibilité d’utilisation avec ou sans eau de
Javel.
Pour traiter le linge avec de l’eau de Javel, ajouter le
bac supplémentaire 3 fourni avec l’appareil. Au moment
de verser l’eau de Javel, attention à ne pas dépasser
le niveau «max» indiqué sur le pivot central (voir figure
page 22).
Pour du linge peu sale ou pour un traitement plus
délicat des tissus, appuyer sur la touche jusqu’à ce
que le niveau «Delicate» soit atteint. Ce cycle réduira
le brassage mécanique pour assurer des résultats de
lavage parfaits du linge délicat.
Modifier les caractéristiques du cycle.
• Appuyersurlatouchepouractiverl’option;levoyant
correspondant à la touche s’allume.
• Appuyerunenouvellefoissurlatouchepour
désactiver l’option; le voyant s’éteint.
! Si l’option sélectionnée est incompatible avec le
programme sélectionné, le voyant se met à clignoter et
l’option n’est pas activée.
! Si l’option sélectionnée n’est pas compatible avec
une autre sélectionnée précédemment, le voyant
correspondant à la première fonction sélectionnée se
met à clignoter et seule la deuxième est activée, le
voyant de l’option activée s’éclaire.
! Les options permettent de modifier le chargement
conseillé et/ou la durée du cycle de lavage.
7. DEMARRER LE PROGRAMME. Appuyer sur la
touche MARCHE/PAUSE. Le voyant correspondant
s’allume en vert fixe et le hublot est verrouillé (symbole
HUBLOT VERROUILLÉ allumé). Pendant le lavage,
le nom de la phase en cours s’affiche à l’écran. Pour
modifier un programme lorsqu’un cycle est en cours,
mettre le lave-linge en pause en appuyant sur la
touche MARCHE/PAUSE (le voyant MARCHE/PAUSE
passe à l’orange et clignote lentement); sélectionner
le cycle désiré et appuyer de nouveau sur la touche
MARCHE/PAUSE. Pour ouvrir la porte tandis qu’un
cycle est en cours, appuyer sur la touche MARCHE/
PAUSE; si le symbole HUBLOT VERROUILLÉ est
éteint, on peut ouvrir le hublot. Pour faire redémarrer le
programme exactement à l’endroit de l’arrêt, appuyer
une nouvelle fois sur la touche MARCHE/PAUSE.
8. FIN DU PROGRAMME. Elle est signalée par
l’inscription “END” qui s’affiche à l’écran ; quand le
symbole HUBLOT VERROUILLÉ s’éteint, on peut
ouvrir le hublot. Ouvrir le hublot, vider le lave-linge et
éteindre l’appareil.
! Une pression prolongée sur la touche permet
d’annuler un cycle déjà lancé. Le cycle est interrompu et
l’appareil s’éteint.
1 / 1

Ariston RPG 822 S EX Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

dans d''autres langues