Generac 2700 PSI 0060222 Manuel utilisateur

www.generac.com or 1-888-436-3722

Operator's Manual

Power Washer

Introduction ............................................................. 1

Safety Rules ...........................................................1

Safety Symbols and Meanings .......................................1

General Information ................................................ 4

Know Your Power Washer .........................................................4

Product Specifications ..............................................................5

Emissions Information ..............................................................5

High Altitude Operation ..............................................................5

Unpacking .................................................................................6

Set-up ..................................................................... 6

Assembly ..................................................................................6

Add Engine Oil ..........................................................................7

Add Fuel ...................................................................................7

Connect Hose and Water Supply to Pump .................................8

How to Use Nozzles ..................................................................9

Cleaning and Applying Detergent ..................................10

Power Washer Rinsing .................................................11

Cleaning Detergent Siphoning Tube ...............................11

Operation .............................................................. 12

Operation ................................................................................12

Power Washer Location ..........................................................12

Checklist Before Starting Engine ..............................................12

How to Start Your Power Washer ............................................12

Automatic Cool Down System (Thermal Relief) .......................14

How to Stop Your Power Washer .............................................14

Maintenance ......................................................... 14

Maintenance Recommendations ..............................................14

Maintenance Schedule ............................................................15

Pump Oil .................................................................................15

Emissions Control ...................................................................15

Power Washer Maintenance ....................................................15

Check and Clean Inlet Screen ..................................................15

Check High Pressure Hoses ....................................................15

Check Detergent Siphoning Tube .............................................15

Check Spray Gun ....................................................................15

Nozzle Maintenance ................................................................15

Engine Maintenance ................................................................16

Engine Oil Recommendations ..................................................16

Check Oil Level ............................................................17

Adding Engine Oil .........................................................17

Changing Engine Oil .....................................................17

Service Air Cleaner .................................................................18

Service Spark Plug ..................................................................18

Inspect Muffler and Spark Arrestor ..........................................18

Remove Spark Arrester Screen .....................................18

After Each Use ........................................................................19

Winter Storage ........................................................................19

Long Term Storage..................................................................20

Protect Fuel System .....................................................20

Protect Engine ..............................................................20

Change Oil ...................................................................20

Protecting the Pump .....................................................20

Other Storage Instructions .......................................................20

Transporting/Tipping of the Unit ..............................................20

Troubleshooting .................................................... 21

Troubleshooting Guide .............................................................21

Manuel del propietario.......................................... 23

Manuel d'entretien ................................................ 47

Table of Contents

INTRODUCTION

Thank you for purchasing this power washer manufactured by

Generac Power Systems, Inc. This model is a high performance,

air-cooled, engine-driven power washer that operates between

2500 and 3100 psi depending on which model you purchased.

The units feature custom designed wheels, axial cam pump

with stainless steel pistons, automatic cool down system, quick

connect nozzles, high pressure hose, detergent siphoning hose

and chemical tank(s) depending on unit model.

Common sense and strict compliance with the special instructions

are essential to preventing accidents. The operator must read

this manual and thoroughly understand all of the instructions

and warnings before using the equipment. If any portion of the

manual is not understood, contact the nearest Authorized Dealer

for starting, operating and servicing procedures. The owner is

responsible for proper and safe use of the equipment.

The power washer can operate safely, efficiently and reliably only if

it is properly located, operated and maintained. Before operating,

servicing or storing:

• Study all warnings in this manual and on the product carefully.

• Become familiar with this manual and the unit before use.

• Refer to the Assembly section of the manual for instructions on

final assembly procedures. Follow the instructions completely.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the power washer

unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

Save these instructions for future reference. If you loan this

device to someone, ALWAYS loan these instructions AND the

Owner's Manual to the individual as well.

WHERE TO FIND US

You can contact Generac Customer Service by phone at 1-888-

436-3722, or on the internet at www.generac.com. Record the

important information of the unit in the following chart for future

reference and/or service inquiries.

Model Number

Serial Number

Date Purchased

SAFETY RULES

Throughout this publication, and on tags and decals affixed to

the power washer, DANGER, WARNING, CAUTION and NOTE

blocks are used to alert personnel to special instructions about

a particular operation that may be hazardous if performed

incorrectly or carelessly. Observe them carefully. Their definitions

are as follows:

Indicates a hazardous situation or action which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided,

could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

SAFETY SYMBOLS AND MEANINGS

KickbackToxic Fumes Electrical Shock

Fluid InjectionFall

Fire Explosion Operator’s Manual

Slippery Surface

Moving Parts Flying Objects Hot Surface

1

Introduction

2



DANGER: Carbon monoxide produced during use CAN KILL

in minutes. NEVER use indoors, in a vehicle, or in other

sheltered areas, EVEN IF doors and windows are open. Only

use OUTSIDE and far away from windows, doors and vents.

Some chemicals or detergents may be harmful if inhaled

or ingested, causing severe nausea, fainting, or poisoning.

• Operate power washer ONLY outdoors.

• A running engine gives off carbon monoxide.

• Carbon monoxide is an odorless, colorless, poisonous gas.

Breathing carbon monoxide can cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting

or death. If you start experiencing any of these symptoms,

IMMEDIATELY move to fresh air. Seek medical attention.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings. Warn any

occupants inside about the symptoms of carbon monoxide so

they know to move to fresh air if they begin to feel ill.

• The use of a carbon monoxide detector inside any occupied

premises between the power washer and the occupant is

recommended.

• NEVER start or run engine indoors, in a vehicle, or in an

enclosed area, EVEN IF windows and doors are open.

• Use a respirator or mask whenever there is a chance that

harmful gas or vapors may be inhaled.

• Read all instructions with respirator or mask so you are certain

the respirator or mask will provide the necessary protection

against inhaling harmful gas or vapors. If you begin to

experience any of the CO symptoms listed above, IMMEDIATELY

move to fresh air.



DANGER: NEVER aim spray gun at people, animals, or

electrical devices. Serious injury or death will result.

ALWAYS point spray gun in safe direction, squeeze spray gun

trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

• The high pressure stream of water that this equipment

produces can cut through skin and its underlying tissues,

leading to serious injury, possible amputation or death.

Spray gun traps high water pressure, EVEN WHEN engine

is stopped and water is disconnected, which can cause

injury.

• NEVER allow CHILDREN to operate power washer or play nearby.

This is NOT a toy.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER secure spray gun in open position.

• NEVER leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• ALWAYS be certain spray gun, nozzles and accessories are

correctly attached.



WARNING: Risk of electrocution.

Contact with power source can cause electric shock or

burn.

• NEVER spray near power source.



WARNING: Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least five (5) feet (152 cm) of clearance on all

sides of power washer including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed

on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.



WARNING: Fuel and its vapors are extremely flammable and

explosive. Fire or explosion can cause severe burns or death.

WHEN ADDING OR DRAINING FUEL

• Turn power washer OFF and let it cool at least two (2)

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting

engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers,

or other appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

Safety Rules

3



WARNING: Use of power washer can create puddles and

slippery surfaces. Kickback from spray gun can cause you to

fall.

• Use only on a level surface.

• The cleaning area should have adequate slopes and

drainage to reduce the possibility of a fall due to slippery

surfaces.

• Do not use on elevated surfaces where chance of kickback

could result in a serious fall.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks

back.



WARNING: Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate power washer without protective housing

or covers.

• DO NOT wear loose clothing, jewelry or anything that

may be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.



WARNING: Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm toward

engine faster than you can let go. Broken bones, fractures,

bruises, or sprains could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• To relieve trapped pressure, point gun in safe direction and

release pressure by pulling/actuating trigger on spray gun.

• When starting engine, pull cord slowly until resistance is felt and

then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, and squeeze spray gun trigger

to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.



WARNING: Unintentional sparking can result in fire or electric

shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER

WASHER.

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.



WARNING: Risk of eye injury. Spray can splash back or

propel objects.

• Always wear safety goggles when using this equipment or

in vicinity of where equipment is in use.

• Before starting the power washer, be sure you are

wearing adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.



WARNING: The engine exhaust from this product contains

chemicals known to the State of California to cause cancer,

birth defects, or other reproductive harm.



WARNING: This product contains lead and lead compounds,

known to the State of California to cause birth defects or

other reproductive harm. Wash your hands after handling this

product.

NOTE:

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when using red (0°) MAX

nozzle.

• NEVER aim spray gun at people, animals, electrical devices or

plants.

NOTE:

Improper treatment of power washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT operate power washer above rated pressure.

• DO NOT modify power washer in any way.

• Before starting power washer in cold weather, check all parts of

the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided

on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating power washer.

• This equipment is designed to be used with Generac authorized

parts ONLY. If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

Safety Rules

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

4

KNOW YOUR POWER WASHER

Read this owner’s manual and safety rules before operating your

high power washer.

If you loan this device to someone, ALWAYS loan these instructions

AND the owner’s manual to the individual as well. Compare the

illustrations with your high power washer to familiarize yourself

with the locations of various controls (Figure 1). Save this manual

for future reference. Replacement owner’s manuals can be printed

from the Generac Web site.

A - Spray Gun – Controls the application of water onto the cleaning

surface with trigger device. Includes a trigger lock.

B - Lance with Quick Connect – Allows you to switch between different

nozzles.

C - High Pressure Hose – Connect one end to water pump and the other

to the spray gun.

D - Recoil Starter – Use for starting the engine.

E - Oil Fill – Check and add engine oil.

F - Air Filter – Protects engine by filtering dust and debris out of the

intake air.

G - Pump – Develops high pressure.

H - Thermal Relief Valve – Cycles water through the pump when water

reaches 125°F warm water will discharge from pump onto ground.

This prevents internal pump damage.

I - Engine On/Off Switch – Turn this switch to “ON” before using the

recoil starter. Turn the switch to “OFF” to stop the engine.

J - Unloader Valve – Controls the high pressure output.

K - High Pressure Outlet – Connection for high pressure hose.

L - Water Inlet – Connection for Garden Hose.

M - Fuel Tank – Fill tank with regular unleaded fuel. Always leave room

for fuel expansion.

N - Fuel On/Off Switch – Turns fuel supply to the engine on and off.

O - Choke – Prepares a cold engine for starting.

P - Throttle Lever – Increases or decreases engine speed. Throttle

should be at maximum travel when the power washer is in use.

Q - Nozzles – Chemical injection, 0°, 15°, 25°, 40° for various high

pressure cleaning applications.

R - Chemical Tank – Used to hold power washer safe detergents to

be siphoned into the low pressure stream. (some units may not be

equipped with tanks or may only have one tank).

S - Warning/Operation Instruction – Identifies proper procedure to

start/stop power washer.

T - Drain Plug – Used to drain engine oil.

U - Serial Number Location

ITEMS NOT SHOWN

• Identification Label (on engine blower housing) – Provides model and

serial number of power washer. Please have these readily available if

calling for assistance.

• Detergent Siphoning Tube/Filter – Use to siphon power washer safe

detergents into the low pressure stream.

General Information

A

C

J

K

L

H

G

T

I

Q

M

D

B

P

O

N

R

F

S

E

U

Figure 1 – Features & Controls

5

General Information

PRODUCT SPECIFICATIONS

CONSUMER

Pressure - (PSI / BAR) 2500/172 2700/186 3100/213

Flow Rate - (GPM / LPM) 2.3/8.7 2.7/10.2

Water supply temperature - (°F / C°) 100/38 Max

Hose length - (Feet / Meters) 25/7.6 25/7.6 30/9.1

Chemical Tank(s) - Number per unit 0 1 2

Chemical Tank - Capacity (Gallon - Liters) N/A 0.75/2.8 0.75/2.8

Nozzles - Number per unit 3 4 5

Lance Length (Inches / cm) 20/51

Gun Standard Deluxe

Engine Displacement - (Cubic Inch / cc) 11.9/196 12.9/212

Spark Plug Type F7TC or equivalent

Spark Plug Gap - (Inches / mm) 0.028-0.031/0.70-0.80

Fuel Capacity - (Quarts / Liters) 3.7/3.5

Oil Capacity - (Oz / Liters) 20/0.6

Low Oil Shut Down System Yes

On/Off Switch Yes

EMISSIONS INFORMATION

The U.S. Environmental Protection Agency (and California Air

Resource Board for equipment certified to CA standards) requires

that this engine comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the engine meets, and to determine

which emissions warranty applies. The engine is certified to meet

the applicable emission standards on gasoline. It is important to

follow the maintenance specifications in the Maintenance section

to ensure that the engine complies with the applicable emission

standards for the duration of the product’s life. This engine utilizes

lean carburetion settings and other systems to reduce emissions.

Tampering with or altering the emission control system may

increase emissions and may be a violation of Federal or California

Law. Acts that constitute tampering include but are not limited to:

• Removal or alteration of any part of the intake, fuel, or exhaust

systems

• Altering or defeating the governor linkage or speed-adjusting

mechanism to cause the engine to operate outside its design

parameters

If you are aware of any of the following symptoms, have your

engine inspected and repaired by your servicing dealer:

• Hard starting or stalling after starting

• Rough idle

• Misfiring or backfiring under load

• Afterburning (backfiring)

• Black exhaust smoke or high fuel consumption

HIGH ALTITUDE OPERATION

The fuel system on this engine may be influenced by operation at

higher altitudes. Proper operation can be ensured by installing an

altitude kit when required. See the table below to determine when

an altitude kit is required. Operating this engine without the proper

altitude kit installed may increase the engine’s emissions and

decrease fuel economy and performance. Kits may be obtained

from any Dealer, and should be installed by a qualified individual.

Altitude* Kit Number PSI

0 - 5000 Feet Not Required 2500/2700/3100

5000 - 7000 Feet 0K2015 2500/2700

5000 - 7000 Feet 0K2016 3100

*Elevation above sea level.

NOTE:

If the altitude kit has been installed and the engine will be

operated at an altitude where the kit is not required, the

engine should be returned to the original factory configuration.

Operating the engine at lower altitudes with the kit installed

may cause the engine to overheat and result in serious engine

damage, and may result in decreased performance and

increased emissions.

6

Set-up

UNPACKING

1. Remove the parts bag, accessories, and inserts included with

power washer.

2. Open carton completely by cutting each corner from top to

bottom.

3. Ensure you have all included items prior to assembly.

• Main Unit

• Handle Assembly

• High Pressure Hose

• Siphon Hose & Filter

• Spray Gun

• Lance with Quick Connect Fitting

• Oil Bottle

• Hose Hook Wireform

• Parts Bag (which includes the following):

– Chemical Tank Cap with hole if model is equipped with a

Chemical Tank

– Operator’s Manual

– Owner’s Registration Card

– Bag containing Color-coded Nozzles

4. If you are missing any items from your carton, please call

Generac Customer Service at 1-888-436-3722. When calling

for assistance, please have the model and serial number from

the data tag available.

5. Fill out and send in registration card. Write Model number,

Serial number & date of purchase in the table located in the

"Where to Find Us" section.

ASSEMBLY

Read entire operator’s manual before you attempt to assemble or If

you have any problems with the assembly of your power washer,

please call Generac Customer Service at 1-888-436-3722. When

calling for assistance, please have the model and serial number

from the data tag available.

1. Place handle (A) onto handle supports (B). Push in latch

buttons and allow handle to slide into position (C). Button will

lock handle into place (Figure 2).

Figure 2 – Attach Handle

NOTE:

It may be necessary to move the handle supports from side to

side in order to align the handle so it will slide over the handle

supports.

2. Install hose hook (Figure 3).

Figure 3 – Install Hose Hook

3. Insert color–colored nozzles in spaces provided in handle

(Figure 4).

4. Place spray gun and nozzle extension into spray gun holder as

shown (Figure 4).

5. Coil high pressure hose and hang on hook.

Figure 4 – Insert Nozzles

7

Set-up

6. Attach siphon tube to location A (Figure 5).

Figure 5 – Siphon Tube Location

A

ADD ENGINE OIL

1. Place power washer on a flat, level surface.

2. Clean area around oil fill and remove orange oil fill cap/

dipstick.

3. Using oil funnel (optional), slowly pour oil into fill opening. See

Maintenance section for oil type recommendation.

NOTE:

On some units there is more than one oil fill location. In these

instances it is only necessary to use one of the oil fill points.

4. Check periodically until the oil level is between "L" and "H" on

the dipstick (Figure 6). DO NOT OVERFILL.

Figure 6 – Dipstick

Acceptable Oil

Level Range

NOTE:

Any attempt to crank or start the engine before it has been

properly serviced with the recommend oil may result in engine

failure.

5. Replace oil fill cap/dipstick and fully tighten.

ADD FUEL

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTE:

Avoid power washer damage. Failure to follow Operator’s

Manual for fuel recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gelling, mix in a fuel stabilizer when

adding fuel. See Storage. All fuel is not the same. If you experience

starting or performance problems after using fuel, switch to a

different fuel provider or change brands.

Fuel and its vapors are extremely flammable

and explosive. Fire or explosion can cause

severe burns or death.

WHEN ADDING FUEL

• Turn power washer OFF and let it cool at least two (2) minutes

before removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful not

to overfill. Fill to bottom of filter screen, this will allow for fuel

expansion (Figure 7).

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

Figure 7 – Adding Fuel

8

CONNECT HOSE AND WATER SUPPLY TO PUMP

NOTE:

DO NOT run the pump without the water supply connected

and turned on. Damage to equipment resulting from failure to

follow this instruction will void warranty.

NOTE:

Remove and discard the shipping cap from the pump’s water

inlet before attaching hose.

1. Run water through your garden hose for 30 seconds to clean

out any debris.

2. Before connecting garden hose to water inlet, inspect inlet

screen (A) (Figure 8). Clean screen if it contains debris or

have it replaced if damaged. DO NOT run power washer if inlet

screen is damaged.

IMPORTANT: DO NOT siphon standing water for the water supply.

Use ONLY cold water (less than 100°F). Water supply must be

adequate to handle greater than 3.8 gallons per minute and no less

than 30 psi.

NOTE:

Using a One Way Valve (vacuum breaker or check valve) at

pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose

between the power washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Figure 8 – Inspect Inlet Screen

A

3. Connect the garden hose (not to exceed 50 feet in length) to

the water inlet (Figure 9). Tighten by hand.

Figure 9 – Connect Garden Hose

Risk of eye injury. Spray can splash back or propel

objects.

• Always wear safety goggles when using this equipment or in

vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

4. Connect lance to spray gun (Figure 10). Tighten by hand.

Figure 10 – Attach Lance

5. Attach end of high pressure hose to base of spray gun (Figure

11). Tighten by hand.

Figure 11 – Connect Hose to Spray Gun

Set-up

9

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVER connect high pressure hose to lance.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

6. Connect high pressure hose to pump (uncoil hose before

connecting to pump or spray gun) (Figure 12). Tighten by

hand.



The hose can be damaged if it comes in contact with a

hot engine or muffler.

Figure 12 – Connect High Pressure Hose to Pump

7. Turn ON the water, squeeze the trigger to purge the pump

system of air (Figure 13).

Figure 13 – Squeeze Trigger

HOW TO USE NOZZLES

The quick–connect on the nozzle lance allows you to switch

between different nozzles. Nozzles can be changed while power

washer is running once spray gun trigger is locked in the safety

position. The nozzles vary the pressure and spray pattern as

shown.

• For most effective cleaning, keep nozzle from 8 to 24 inches (20

to 61 cm) away from cleaning surface.

• If you get nozzle too close, especially using a high pressure

nozzle, you may damage surface being cleaned.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVER exchange nozzles without the trigger lock being engaged on

the spray gun.

• DO NOT twist nozzles while spraying.

Follow these instructions to change nozzles:

1. Pull back collar on quick–connect and pull current nozzles

off. Store nozzles in holder provided on the accessory storage

(Figure 14).

Figure 14 – Nozzles

2. Select desired nozzle.

3. Pull back on collar, insert new nozzle and release collar. Tug

on nozzle to make sure it is securely in place.

• For delicate rinse (lower pressure and higher flow), for gentle

cleaning of cars/trucks, boats, RV’s, patio furniture, lawn

equipment, etc., select white nozzle (Figure 15).

Figure 15 – Wash Pressure Nozzle (White)

Set-up

10

• For general rinsing (medium pressure and medium flow), ideal for

most all purpose cleaning such as home siding, brick patios, wood

decks, driveways and sidewalks, garage floors, etc., select green

nozzle (Figure 16).

Figure 16 – Clean Pressure Nozzle (Green)

• For medium rinsing (higher pressure and medium flow), ideal

for removing stains on hard porous surfaces such as concrete

dirveways, garage floors and brick patios, select yellow nozzle

(Figure 17).

Figure 17 – Strip Pressure Nozzle (Yellow)

• For maximum rinsing (higher pressure and lower flow), for

stubborn or hard to reach surface such as second story surfaces,

paint removal, oil stains, rust removal or other stubborn substances

(tar, gum, grease, wax, etc.), select red nozzle (Figure 18).



This tip (Red Nozzle) can damage work surface if it is

too close or held in one position for an extended time.

Figure 18 – Blast Pressure Nozzle (Red)

• When applying detergent, use only the black nozzle (Figure 19).

Only use power washer safe detergents/soaps to help break down

stubborn dirt and grime on a variety of surfaces.

Figure 19 – Detergent Nozzle (Black)

CLEANING AND APPLYING DETERGENT



Chemicals can cause bodily injury, and/or property

damage.

• NEVER use caustic liquid with power washer.

• Use ONLY power washer safe detergents/soaps. Follow all

manufacturer's instructions.

To apply detergent, follow these steps:

1. Review use of nozzles.

2. Open container cap (if so equipped, Figure 20).

3. Prepare detergent solution as required by job.

Figure 20 – Chemical Tank & Cover

Container

Cap

4. Depending on model, insert filter on end of siphoning tube

through the hole in the loose cap (supplied) (Figure 21).

5. Install cap and siphoning tube onto tank.

6. Make sure siphoning tube remains fully submerged into

detergent.

Set-up

11

Figure 21 – Install Siphoning Tube

NOTE:

Make sure the filter remains fully submerged in detergent

while applying detergent.

NOTE:

Contact with the hot muffler can damage detergent siphoning

tube.

• When inserting the siphon into a detergent solution bottle, route the

tube so as to keep it from inadvertently contacting the hot muffler.

7. Make sure black detergent nozzle is installed.

NOTE:

Detergent cannot be applied with the high pressure nozzle

(Yellow, White, Green or Red). Only use the Black nozzle with

detergent.

8. Confirm set-up instructions have been followed.

NOTE:

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without the

water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this instruction

will void warranty.

9. Start engine following instructions How to Start Your Power

Washer.

10. Apply detergent to a dry surface, starting at lower portion

of area to be washed and work upward using long, even,

overlapping strokes.

11. Allow detergent to "soak in" for 3-5 minutes before washing

and rinsing. Reapply as needed to prevent surface from

drying. DO NOT allow detergent to dry on surface being

cleaned (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after

each use by placing the filter into a bucket of clean water, then run

the power washer in low pressure for 1-2 minutes.

POWER WASHER RINSING

1. Remove black detergent nozzle from lance.

2. Select and install desired high pressure nozzle following

instructions How to Use Nozzles.

3. Point spray gun in safe direction and away from people,

animals and plants. Squeeze trigger to flush any remaining

chemical from system.

4. Keep spray gun a safe distance from area you plan to spray.

Kickback from spray gun can cause you to fall.

• Use only on a level surface.

• Do not use on elevated surface to prevent the risk

of a serious fall.

• Be extremely careful if you must use the power washer from a

ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high pressure

spray to avoid injury when spray gun kicks back.

5. Apply a high pressure spray to a small area and then check

surface for damage. If no damage is found, you can assume

it is okay to continue rinsing.

6. Start at top of area to be rinsed, working down with same

overlapping strokes as you used for cleaning.

CLEANING DETERGENT SIPHONING TUBE

If you used the detergent siphoning tube, you must flush it with

clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of clean

water.

2. Remove high pressure nozzle from nozzle extension.

3. Select and install black detergent nozzle following instructions

How to Use Nozzles.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop Power

Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction, squeeze spray

gun trigger to release retained high water pressure. Engage

trigger lock when not in use.

IMPORTANT: Spray gun traps high water pressure, even when

engine is stopped and water is disconnected.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• ALWAYS point spray gun in safe direction, and squeeze spray

gun trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

Operation

12

OPERATION

If you have any problems operating your power washer, please call

Generac customer service at 1-888-436-3722.

POWER WASHER LOCATION

Clearances and Air Movement

Running engine gives off carbon monoxide, an

odorless, colorless, poisonous gas. Breathing carbon

monoxide can cause headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea, fainting or

death. For more information, reference the CO

warnings in the Safety Rules section.

Place power washer outdoors in an area that will not accumulate

deadly exhaust gas. NEVER place power washer where exhaust

gas could accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is kept away

from any windows, doors, ventilation intakes, or other openings

that can allow exhaust gas to collect in a confined area. Prevailing

winds and air currents should be taken into consideration when

positioning power washer (Figure 22).

• Operate power washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through windows,

doors, ventilation intakes, or other openings.

• NEVER start or run engine indoors, in a vehicle or in an enclosed

area, EVEN IF windows and doors are open.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of power washer

including overhead.

Figure 22 – Building Clearances

5 Foot Minimum

CHECKLIST BEFORE STARTING ENGINE

1. Be sure to read and understand the Operator Safety section

and Operation section before using power washer.

2. Check that oil is at the proper level in the engine crankcase and

that fuel has been added to the fuel tank.

3. Review the unit's assembly and ensure fitting are properly

secured and make sure there are no kinks, cuts, or damage to

high pressure hose.

4. Provide a proper water supply at an adequate flow, clear

screens of debris, and confirm that the system is purged of air.

5. Confirm unit is secure on level ground and surrounding work

area is clear.

HOW TO START YOUR POWER WASHER

NOTE:

DO NOT run the pump without the water supply connected

and turned on. Damage to equipment resulting from failure to

follow this instruction will void warranty.

1. Move the fuel valve lever to the ON position (Figure 23).

Figure 23 – Fuel Valve

Off

On

2. Move choke lever to “CLOSE” position (Figure 24).

NOTE:

For a warm engine, be sure the choke lever is in the “OPEN”

position.

Figure 24 – Choke Lever

Choke

Close

Open

Operation

13

3. Move throttle control lever to “HIGH” position, shown on

engine as a rabbit (Figure 25).

Figure 25 – Throttle Control

High Low

4. Turn the engine switch to the "ON" position (Figure 26).

Figure 26 – The ON Position

OFF

ON

IMPORTANT: Before starting the power washer, be sure you are

wearing adequate safety goggles.

Risk of eye injury. Spray can splash back or propel

objects.

• Always wear safety goggles when using this equipment or in

vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

5. Place foot on footpad or otherwise secure unit from movement

when pulling recoil.

6. When starting the engine, grasp starter grip handle (Figure

27) and pull slowly until you feel some resistance. Then pull

rapidly to start engine.

Figure 27 – Starting the Engine

Starter Handle

Starter cord kickback (rapid retraction) can result in

bodily injury. Kickback will pull hand and arm toward

engine faster than you can let go. Broken bones,

fractures, bruises, or sprains could result.

• NEVER pull starter cord without first relieving spray gun pressure.

• When starting engine, pull cord slowly until resistance is felt and

then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always point

spray gun in safe direction and squeeze spray gun trigger to release

high pressure.

• Firmly grasp spray gun with both hands when using high pressure

spray to avoid injury when spray gun kicks back.

7. Return starter grip handle slowly. DO NOT let rope “snap back”

against starter.

8. When engine starts, slowly move choke lever to “OPEN”

position as engine warms. If engine falters, move choke lever

to “CLOSE” position, then to “OPEN” position (Figure 28).

Figure 28 – Choke Lever

Choke

Open

9. After each starting attempt, where engine fails to run, always

point gun in safe direction, and squeeze spray gun trigger to

release high pressure.

10. If engine fails to start after six pulls, move choke lever to

“OPEN” position, and repeat steps 6 through 10.

Operation

14

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate power washer or play nearby.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• NEVER aim spray gun at people, animals or electrical devices.

Serious injury will result.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

 Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of power

washer including overhead.

• It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442, maintained in effective

working order. Other states or federal jurisdictions may have

similar laws.

• Replacement parts must be the same and installed in the same

position as the original parts.

AUTOMATIC COOL DOWN SYSTEM (THERMAL

RELIEF)

If you run the engine on your power washer for 3-5 minutes

without pressing the trigger on the spray gun, circulating water

in the pump can reach temperatures above 125°F. The system

engages to cool the pump by discharging the warm water onto

the ground.

HOW TO STOP YOUR POWER WASHER

1. Release spray gun trigger.

2. Move throttle control lever on engine to “LOW” (turtle)

position (Figure 29).

3. Turn the engine ON/OFF switch to the "OFF" position.

4. ALWAYS point spray gun in a safe direction, and squeeze

spray gun trigger to release retained high water pressure.

Engage trigger lock when not in use.

5. Turn OFF water supply.

Figure 29 – Throttle Position

High Low

IMPORTANT: Spray gun traps high water pressure, even when

engine is stopped and water is disconnected.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze spray gun

trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

MAINTENANCE RECOMMENDATIONS

Regular maintenance will improve the performance and extend

the life of the power washer. See any qualified dealer for service.

The power washer’s warranty does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the power washer

as instructed in this manual, including proper storage as detailed

in Winter Storage and Long Term Storage.

NOTE:

Should you have questions about replacing components

on your power washer, please call 1-888-436-3722 for

assistance.

Some adjustments will need to be made periodically to properly

maintain your power washer.

All service and adjustments should be made at least once each

season. Follow the requirements in the Maintenance Schedule

chart.

NOTE:

Once a year you should clean or replace the spark plug, clean

or replace the air filter, and check the spray gun and nozzle

extension assembly for wear. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Maintenance

15

MAINTENANCE SCHEDULE

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse

conditions.

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check/clean water inlet screen*

Check high pressure hose

Check detergent siphoning hose/filter

Check spray gun and assembly for leaks

Clean debris

Check engine oil level

Every 20 Hours or Every Season

Change engine oil**

Every 50 Hours or Every Season

Check/clean air cleaner filter**

Inspect muffler and spark arrester*

Every 100 Hours or Every Season

Service spark plug

* Clean if clogged. Replace if perforated or torn.

** Service more often under dirty or dusty conditions.

PUMP OIL

DO NOT attempt any oil maintenance on this pump. The pump is

pre-lubricated and sealed from the factory, requiring no additional

maintenance for the life of the pump.

EMISSIONS CONTROL

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road engine

repair establishment or individual. However, to obtain ”no

charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

POWER WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the power washer. These

openings must be kept clean and unobstructed.

Power washer parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTE:

Improper treatment of power washer can damage it and

shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

CHECK AND CLEAN INLET SCREEN

Examine the screen on the pump’s water inlet. Clean it if the screen

is clogged or replace it if screen is damaged.

CHECK HIGH PRESSURE HOSES

The high pressure hoses can develop leaks from wear, kinking, or

abuse. Inspect the hoses each time before using them. Check for

cuts, leaks, abrasions or bulging of cover, damage or movement

of couplings. If any of these conditions exist, replace the hose

immediately.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST meet or exceed maximum

pressure rating of unit.

CHECK DETERGENT SIPHONING TUBE

Examine the filter on the detergent tube and clean if clogged. The

tube should fit tightly on the barbed fitting. Examine the tube for

leaks or tears. Replace the filter or tube if either is damaged.

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it is

secure. Test the trigger by pressing the trigger, it “springs back”

into place when you release it. Replace spray gun immediately if

it fails to "spring back".

NOZZLE MAINTENANCE

A pulsing sensation felt while squeezing the spray gun trigger

may be caused by excessive pump pressure. The principal cause

of excessive pump pressure is a nozzle clogged or restricted

with foreign materials, such as dirt, etc. To correct the problem,

immediately clean the nozzle following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, squeeze spray

gun trigger to release retained high water pressure.

Maintenance

16

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• ALWAYS point spray gun in safe direction, and squeeze spray gun

trigger to release high pressure every time you stop engine. Engage

trigger lock when not in use.

3. Remove nozzle from end of nozzle extension.

4. Use a small paper clip to free any foreign material clogging or

restricting nozzle (Figure 30).

Figure 30 – Free Foreign Material

5. Remove lance from spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through lance (Figure 31). Back flush between

30 to 60 seconds.

7. Reinstall nozzle into lance.

8. Reconnect lance to spray gun.

Figure 31 – Back Flush Lance

9. Make sure garden hose is connected to pump water inlet.

Check that high pressure hose is connected to spray gun and

pump. Turn on water.

10. Start engine following instructions How to Start Your Power

Washer.

11. Test power washer by operating with each quick connect

nozzle.

ENGINE MAINTENANCE

 Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER

WASHER

• Disconnect the spark plug wire from the spark plug and place the

wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

ENGINE OIL RECOMMENDATIONS

We recommend the use of high-quality detergent oils acceptable if

classified for service SF, SG, SH, SJ or higher. DO NOT use special

additives.

Outdoor temperatures determine the proper oil viscosity for the

engine. Use the chart to select the best viscosity for the outdoor

temperature range expected.

SAE 30*

SA E 30 *

10W-30**

10 W- 30 * *

5W-30

5W -3 0

* Below 50°F (10°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.

Check oil level more frequently.

NOTE:

Synthetic oil meeting ILSAC GF-2, API certification mark

and API service symbol with “SJ/CF ENERGY CONSERVING”

or higher, is an acceptable oil at all temperatures. Use of

synthetic oil does not alter required oil change intervals.

NOTE:

The engine is equipped with an "Oil Alert System". This

system will automatically stop the engine before the oil level

falls below a safe limit. To avoid the inconvenience of an

unexpected shutdown, always check the engine oil level before

startup.

Maintenance

17

CHECK OIL LEVEL

Oil level should be checked prior to each use or at least every 8

hours of operation. Keep oil level maintained.

1. Make sure power washer is on a level surface.

2. Clean area around oil fill and wipe dipstick clean remove oil fill

cap (Figure 32).

3. Verify oil is at the proper level on the dipstick.

4. Insert the dipstick into filler neck but do not screw it in.

5. Replace and tighten oil fill cap.

Figure 32 – Fill Engine Oil

ADDING ENGINE OIL

1. Make sure power washer is on a flat, level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening until the proper

level on the dipstick is reached.

4. Insert the dipstick into filler neck but do not screw it in.

5. If level is low, fill until the oil level is between "L" and "H" on the

dipstick (Figure 33).

6. Replace and tighten oil fill cap.

Figure33 – Dipstick

Acceptable Oil

Level Range

CHANGING ENGINE OIL

If you are using your power washer under extremely dirty or dusty

conditions, or in extremely hot weather, change the oil more often.



Avoid prolonged or repeated skin contact with used

motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.



KEEP OUT OF REACH OF CHILDREN.

• Don’t pollute. Conserve resources. Return used oil to

collection centers.

Change oil while engine is still warm from running, as follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

3. Clean area around oil drain plug (A) (Figure 34). The oil drain

plug is located at base of engine, opposite carburetor.

4. Remove oil fill cap (Figure 32).

5. Remove oil drain plug and drain oil completely into a suitable

container.

6. Reinstall oil drain plug and tighten securely.

7. Slowly pour oil (about 20 oz.) into oil fill opening to the proper

level on the dipstick. DO NOT overfill.

8. Reinstall oil fill cap. Finger tighten cap securely.

9. Wipe up any spilled oil.

10. Properly dispose of oil in an accordance with all local

regulations.

Figure 34 – Oil Drain Plug

A

Maintenance

18

SERVICE AIR CLEANER

Your engine will not run properly and may be damaged if you run it

with a dirty air cleaner. Service more often if operating under dirty

or dusty conditions.

To service the air cleaner, follow these steps:

1. Pull on air cleaner cover latch and remove cover (Figure 35).

2. Loosen wing nut.

3. Carefully remove filter assembly.

4. Remove foam filter.

5. To clean cartridge, gently tap on a flat surface.

6. Reinstall foam filter.

7. Reinstall clean or new cartridge assembly.

8. Reinstall wing nut and tighten.

9. Install cover by snapping latch closed.

Figure 35 – Service the Air Cleaner

Air Cleaner

Cover

Paper Filter

Element

Foam Filter

Element

Gasket

Latch

SERVICE SPARK PLUG

Changing the spark plug will help your engine to start easier and

run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug (Figure 36).

3. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary (see

Specifications).

4. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use the recommended replacement

plug. See Specifications.

5. Install spark plug and tighten firmly.

Figure 36 – Change the Spark Plug

SPARK PLUG

0.028-0.031

in

INSPECT MUFFLER AND SPARK ARRESTER

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for damage or

carbon blockage. If replacement parts are required, make sure to

use only original equipment replacement parts.

REMOVE SPARK ARRESTER SCREEN

Tools Required: 8mm Box Wrench

1. Remove heat shield from the muffler by loosening the four (4)

Bolts (A) (Figure 37).

2. Remove the spark arrester from the muffler by loosning the

two (2) Bolts (B) (Figure 38).

3. Inspect the spark arrester, replace if torn, perforated or

otherwise damaged (part number 0K1851). DO NOT USE A

DEFECTIVE SCREEN.

4. If screen is not damaged, clean it with a commercial solvent

and replace.

Figure 37 – Remove Heat Shield

A

Maintenance

La page est en cours de chargement...

Generac 2700 PSI 0060222 Manuel utilisateur

Generac 2700 PSI 0060222 Manuel utilisateur

dans d''autres langues