Samsung RF26HFP Series Manuel utilisateur

Marque: Samsung

Modèle: RF26HFP Series

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory parts,

please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

Free Standing Appliance

English

RF261B*****

RF260B*****

RF26HFP***

02_ Safety information

safety information

SAFETY INFORMATION

Before using your new Samsung French Door

Refrigerator, please read this manual thoroughly to

ensure that you know how to operate the features

and functions that your new appliance offers safely

and efﬁ ciently.

This appliance is not intended for use by persons

(including children) with reduced physical,

sensory, or mental capabilities, or those who lack

experience and knowledge, unless they have been

given supervision or instruction concerning the

use of the appliance by a person responsible for

their safety.

Because the following instructions cover various

models, the characteristics of your refrigerator

may differ slightly from the refrigerator described in

this manual. If you have any question, contact us

at 1-800-SAMSUNG or ﬁ nd help and information

online at www.samsung.com.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

SEVERE WARNING SIGNS

FOR INSTALLATION

Do not install the refrigerator in a damp •

place or place where it may come in

contact with water.

Deteriorated insulation of electrical parts may -

cause an electric shock or ﬁ re.

Do not place this refrigerator in direct sunlight •

or expose to the heat from stoves, room

heaters or other appliance.

Do not plug several appliances into the same •

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

This provides the best performance and -

also prevents overloading house wiring

circuits, which could cause a ﬁ re hazard from

overheated wires.

If the wall socket is loose, do not insert the •

power plug.

There is a risk of electric shock of ﬁ re. -

Do not use a cord that shows cracks or abrasion •

damage along its length or at either end.

Do not bend the power cord excessively or •

place heavy articles on it.

Do not twist or tie the power cord.•

Do not hook the power cord over a metal •

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

When moving the refrigerator, be careful not to -

roll over or damage the power cord

This may result in an electric shock or ﬁ re. -

Never unplug your refrigerator by pulling on the •

power cord. Always grip plug ﬁ rmly and pull

straight out from the outlet.

Damage to the cord may cause a short-circuit, -

ﬁ re and/or electric shock.

Do not use aerosols near the refrigerator.•

Aerosols used near the refrigerator may cause -

an explosion or ﬁ re.

Do not install this appliance near a heater, •

inﬂ ammable material.

Do not install this appliance in a humid, oily or •

dusty location, in a location exposed to direct

sunlight and water (rain drops).

Do not install this appliance in a location where •

gas may leak.

WARNING

Safety information _03

This may result in an electric shock or ﬁ re. -

This refrigerator must be properly •

installed and located in accordance with

the manual before you use it.

Connect the power plug in the proper position •

with the cord hanging down.

If you connect the power plug upside down, -

the wire can get cut off and cause a ﬁ re or

electric shock.

When moving the refrigerator, be careful not to •

roll over or damage the power cord.

This constitutes a ﬁ re hazard. -

Make sure that the power plug is not squashed •

or damaged by the back of the refrigerator.

Keep the packing materials out of reach of •

children.

There is a risk of death from suffocation if a child -

puts the packing materials on his or her head.

The appliance must be positioned so that the •

plug is accessible after installation.

You need to remove all the protective plastic •

ﬁ lm before you initially plug the product in.

The refrigerator must be safely grounded.•

Always make sure that you have -

grounded the refrigerator before

attempting to investigate or repair any

part of the appliance. Power leakages

can cause severe electric shock.

Never use gas pipes, telephone lines or other •

potential lightning attractors as an electrical

ground.

Improper use of the grounding plug can result -

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-120 V,

10 A, or more. If a grounding adapter is used,

make sure the receptacle box is fully grounded.

If the power cord is damaged, •

have it replaced immediately by the

manufacturer or its service agent.

INSTALLATION CAUTIONS

Allow sufﬁ cient space to install the •

refrigerator on a ﬂ at surface.

If your refrigerator is not level, the internal -

cooling system may not work correctly.

Keep the ventilation space in the appliance •

enclosure or mounting structure clear of

obstruction.

Allow the appliance to stand for 2 hours after •

installation.

We recommend you have installed this refrigerator •

by a qualiﬁ ed technician or service company.

Failing to do so may result in an electric shock, -

ﬁ re, explosion, problems with the product, or

injury.

CRITICAL USAGE WARNINGS

Do not insert the power plug with wet •

hands.

•

Do not store articles on the top of the appliance.

When you open or close the door, the articles -

may fall and cause personal injury and/or

material damage.

Do not put a container ﬁ lled with water on the •

refrigerator.

If spilled, there is a risk of ﬁ re or electric shock. -

Children should be supervised to ensure that •

they do not play with the appliance.

Keep ﬁngers out of “pinch point” areas; -

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

Do not let children hang on the door. A serious •

injury may occur.

Do not let children go inside the refrigerator.•

Children could become trapped.

Do not insert your hands into the bottom area •

under the appliance.

Any sharp edges may cause personal injury. -

Do not let children step on a drawer’s cover.•

The drawer may break and cause them to slip. -

Do not overﬁ ll the refrigerator with food.•

When you open the door, an item may fall out -

and cause personal injury or material damage.

Do not touch the inside walls of the freezer or •

products stored in the freezer with wet hands.

This may cause frostbite. -

Never put ﬁ ngers or other objects into the water •

dispenser hole, ice chute, or ice maker bucket.

It may cause personal injury or material damage. -

Do not spray ﬂ ammable gas near the refrigerator.•

There is a risk of explosion or ﬁ re. -

Do not store volatile or ﬂ ammable substances •

in the refrigerator.

The storage of benzene, thinner, alcohol, ether, -

LP gas and other such products may cause

explosions.

Do not store pharmaceuticals products, •

scientiﬁ c materials, or temperature sensitive

products in the refrigerator.

Products that require strict temperature -

controls must not be stored in the refrigerator.

Do not place or use an electrical appliance •

inside the refrigerator, unless it is of a type

recommended by the manufacturer.

CAUTION

WARNING

04_ Safety information

Do not stand on top of the appliance or place •

objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal

objects, etc.) on the appliance. This may result

in an electric shock, ﬁ re, problems with the

product, or injury. Do not put a container ﬁ lled

with water on the appliance.

If spilled, there is a risk of ﬁ re or electric shock. -

Do not use mechanical devices or any other •

means to accelerate the defrosting process, other

than those recommended by the manufacturer.

Do not damage the refrigerant circuit.•

Do not spray volatile material such as •

insecticide onto the surface of the appliance.

As well as being harmful to humans, it may -

also result in an electric shock, ﬁ re or problems

with the product.

Never stare directly at the UV LED lamp for •

long periods of time.

This may result in eye strain due to the -

ultraviolet rays.

Do not disassemble or repair the •

refrigerator by yourself.

You run risk of causing a ﬁ re, malfunction and/ -

or personal injury.

When the interior or exterior LED lamp has -

gone out, please contact your service agents.

Children should be supervised to ensure •

that they do not play with the appliance.

Keep ﬁ ngers out of “pinch point” areas : -

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area. Do not

let children hang on the door. If not, a serious

injury may occur. Risk of children entrapment.

Do not let children enter inside the refrigerator.

Bottles should be stored tightly together so •

that they do not fall out.

This product is intended only for the storage of •

food in a domestic environment.

If a gas leak is detected, avoid any naked •

ﬂ ames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

Do not touch the appliance or power cord. -

Do not use a ventilating fan. -

A spark may result in explosion or ﬁ re. -

Use only the LED Lamps provided by •

manufacturer or service agents.

If there are burning smells or smoke, pull •

out power plug immediately and contact

your Samsung Electronics service center.

If you experience difﬁ culty when changing the •

light, contact a service agent.

If the product is equipped with LED Lamps, •

do not disassemble the Lamp Cover and LED

Lamp by yourself.

Please contact your service agents. -

If any dust or water is in refrigerator, pull out •

the power plug and contact your Samsung

Electronics service center.

Otherwise there is a risk of ﬁ re. -

USAGE CAUTIONS

Do not re-freeze frozen foods that •

have thawed completely. Do not place

carbonated or ﬁ zzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

When the contents freeze, the glass may break -

and cause personal injury.

Use only the ice maker provided with the •

refrigerator. The water supply to this refrigerator

must only be installed/connected by a suitably

qualiﬁ ed person and connected to a potable

water supply only. In order to operate the

ice maker properly, water pressure of 20 ~

125psi is required. If you have a long vacation

or business trip and won’t use water or ice

dispensers, close the water valve.

Otherwise, water leakage may occur. -

Wipe excess moisture from the inside and •

leave the doors open.

Otherwise, odor and mold may develop. -

Service warranty and Modiﬁ cation.•

Any changes or modiﬁ cations performed -

by a 3rd party on this ﬁ nished appliance

are not covered under Samsung

warranty service, nor can Samsung be

responsible for safety issues that result

from 3rd party modiﬁ cations.

Do not block air holes.•

If the air holes are blocked, especially with a -

plastic bag, the refrigerator can be over cooled.

If this cooling period lasts too long, the water

ﬁ lter may break and cause water leakage.

If the refrigerator is disconnected from the •

power supply, you should wait for at least ﬁ ve

minutes before plugging it back in.

If you have a long vacation planned or the •

refrigerator is not to be used for a long period

of time, you must empty the refrigerator and

pull out the power plug.

Letting the refrigerator run for a long time -

without using it can cause the insulation to

deteriorate and may cause a ﬁ re.

CAUTION

Safety information _05

Wipe excess moisture from the inside and -

leave the doors open. Otherwise, odor and

mold may develop.

To get the best performance from the product:

Do not place foods too close to the vents at -

the rear of the appliance as it can obstruct free

air circulation in the refrigerator compartment.

Wrap food up properly or place it in airtight -

containers before putting it into the refrigerator.

Fill the water tank, ice tray, and water cubes

only with potable water.

If the product is ﬂ ooded, make sure to

contact your nearest service center.

There is a risk of electric shock or ﬁ re. -

CLEANING CAUTIONS

Do not directly spray water on the inside

or outside the refrigerator.

There is a risk of ﬁ re or electric shock. -

Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

the refrigerator to remove bad odors.

This may result in an electric shock or ﬁ re. -

Remove any foreign matter or dust from

the power plug pins. Do not use a wet

or damp cloth when cleaning the plug.

Otherwise, there is a risk of ﬁ re or electric shock. -

Unplug the refrigerator before cleaning

or making repairs.

WARNING

This product contains chemicals known to

the State of California to cause cancer and

reproductive toxicity.

CRITICAL DISPOSAL

WARNINGS

Risk of child entrapment. Before you

throw away your old refrigerator or freezer:

Leave the shelves in place so that children can -

not easily climb inside.

Please dispose of the packaging material from

this product in an environmentally friendly

manner.

Leave the shelves in place so that children

can not easily climb inside. Ensure that none

of the pipes on the back of the appliance are

damaged prior to disposal.

R600a or R134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂ ammable

gas (Refrigerant R600a), contact your local

authority in regard to safe disposal of this

product.

When disposing of this refrigerator, remove the

door/door seals and door latch so that small

children or animals cannot become trapped

inside. Children should be supervised to ensure

that they do not play with the appliance.

Cyclopentane is used in the insulation. The

gases in the insulation material require a special

disposal procedure. Please contact your local

authorities in regard to the environmentally safe

disposal of this product. Ensure that none of

the pipes on the back of the refrigerator are

damaged prior to disposal.

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ……………………………………………… 06

OPERATING YOUR FRENCH DOOR REFRIGERATOR ………………………………………………… 13

TROUBLESHOOTING ……………………………………………………………………………………… 24

WARNING

CAUTION

06_

setting up

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

A location with easy access to a water supply.

Choose:

A location without direct exposure to sunlight.

A location with a level ﬂoor.

A location with enough space for the

refrigerator doors to open easily.

A location that allows sufﬁcient space to the

right, left, back and top for air circulation.

A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

Do not install the refrigerator where the

temperature will go below 50ºF (10ºC).

When moving your refrigerator

To prevent ﬂoor damage, be sure the front

adjusting legs are in the up position (above

the ﬂoor). Refer to ‘Adjusting the Level’ in

the manual (on page 9).

Flat-blade screw

driver(-)

Control Lever

CAUTION

DA68-02601A(EN+FR+ES)-0.2.indb 6 2012.3.31 9:49:31 AM

Model

Depth “A” 33 27/32” (860mm)

Width “B” 35 25/32” (909mm)

Height “C” 68 3/8” (1737mm)

Overall Height “D”

Depth “E” 36 7/32” (920mm)

RF260B**/ RF261B** / RF26H**

The measurements here are based on

depending on the measuring method.

Do not locate the refrigerator where it may

become wet.

140

2”

(50 mm)

13 3/4”

(340 mm)

63 25/32”

(1620 mm)

1 37/64”

(40 mm)

3 3/4”

(95 mm)

29 6/64”

(740 mm)

48 1/32”

(1220 mm)

35 25/32”

(909 mm)

Selecting the best location for the refrigerator

70” (1778 mm)

setting up

_07

01 SETTING UP

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 335lbs (152kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

REQUIRED TOOLS

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Allen wrench

(3/16”) (5mm)

REMOVING THE

REFRIGERATOR DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁnal location. Do not remove

the doors/drawer if you don’t need to.

If you do

not need to remove the refrigerator doors, go to

Adjusting the Level on page 9. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator before

removing the door or drawer.

Be careful not to drop, damage or scratch

the door/drawer while removing them.

Reattach the doors/drawer properly to

avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door

seal.

Use care when you remove the doors/

drawer. The

doors are heavy and you

could injure yourself.

WARNING

DA68-02601A(EN+FR+ES)-0.2.indb 7 2012.3.31 9:49:32 AM

HOW TO ASSEMBLE THE HANDLE

Orient each handle so that the end with the sticker

attached is at the top and the holes with the

tightening screws are facing each other.

Then, follow the directions below to install each

handle.

By using Phillips screwdriver, ﬁx the screw

(optional) and then put the handle on the ﬁxer

by sliding them down ﬁrmly.

setting up

08_

Fix the handles to the doors by sliding them left

side ﬁrmly.

2012.3.31 9:49:32 AM

Fix the handles to the doors by

sliding them down ﬁrmly.

Tighten with wrench

Drawer door handle assembly

Check the direction of Handle

assembly.

Fix the handles to the doors by

sliding them left side ﬁrmly.

Tilt up the Handle bar and tighten with wrench

ﬁrmly.

Disassemble the refrigerator doors

Be careful not to drop and scratch the

doors while removing them.

With the door opened

Remove 3 screws holding down the TOP 1.

TABLE ( 1 ) and turn it with wires connected.

Disconnect two connector (

) on the left side

door. To remove the water coupler from the

WARNING

hinge, twist and pull it from the hinge.

screw

_09

setting up

Pull and remove the hinge lever ( 3

) . Remove

the ground screw ( 4 ) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

( 5 ).

Lift the door straight up to remove.4.

Remove the screw (5. 6 ) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

( 7 ) attached to the lower left and right door

hinges with an allen wrench (3/16”). Remove

the lower left and right door hinges (

Take out the upper drawer by lifting it up.

8 ).

DISASSEMBLE THE FLEX DOOR

Take out the lower basket ( 1

) by lifting the

basket up from the rail system.

Press the ﬁ xing hook of rail system. 3.

Holding the top of the Freezer Drawerpull it out all4.

the way and then remove it from the rail system.

Be careful not to scratch or dent the sliding

Make sure that you mount the freezer

basket in the right position when removing

/ installing the freezer door. Failing to do

so may result in the door not opening or

closing properly.

Do not overload the bottom basket or

the top drawer. Overloading prevents the

Freezer drawer from closing properly and

will eventually cause frost build-up.

Allen wrench

CAUTION

01 SETTING UP

setting up

10_

MAKING MINOR ADJUSTMENTS

BETWEEN DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

The left door is ﬁ xed. To make minor

adjustments between doors, adjust only

the right door.

ASSEMBLE THE FREEZER

DRAWER

To reattach the drawer after you have moved

the fridge to its ﬁ nal location, assemble the parts in

reverse order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁ nal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

How to adjust the level

Open the freezer drawer and remove the lower

basket.

Insert a ﬂat-blade screwdriver (-) into a notch

on the left control lever, and turn it counter

clockwise to level the refrigerator. (You turn the

lever clockwise to lower the refrigerator and

counterclockwise to raise it.)

Both control levers must be touching the

ﬂ oor to avoid possible personal injury or

property damage because of tipping.

If the right side is lower, perform the same

procedure, but with the right control lever.

It is difﬁ cult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to the

next page for the best way to make minor

adjustments to the doors.

CAUTION

ﬂ at-blade screwdriver(-)

Control Lever

Adjustment

part

Fixed part

1. Pull out the freezer drawer ,then you can

see the lower hinge .

3. Adjust the height by turning a philips

screwdriver (+) clockwise ( ) or

counterclockwise ( ).

Insert a philips screwdriver (+) into the shaft

of the lower hinge.

DOWN

When you turn a philips screwdriver (+)

counterclockwise ( ), the door will

move up.

_11

setting up

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁ lter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁ lter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

The water line also connects to the ice maker.

For the ice maker to operate properly, water pressure

of 20~125psi ( 138~862kPa) is

required.

If the refrigerator is installed in an area with low

water pressure (below 20psi), you can install

a booster pump to compensate for the low

pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator

is properly ﬁ lled. To do this, press the water

dispenser lever until the water runs from the water

outlet.

Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper tubing

and ¼” compression nut.

Connecting to the water supply line

supply.

Locate the nearest cold water drinking line and 2.

Connect the water line installation kit to the 3.

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁ nd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

¼” copper tubingt

¼” compression nut (1pc)t

Ferrule (2pc)t

¼” plastic tubing t

Molded end(Bulb)

¼” compression nut (1pc)t

Connect the household water line to the 1.

assembled compression ﬁ tting.

If you are using copper tubing, slip the -

compression nut ( B ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

If you are using plastic tubing ( - B ) , insert the

molded end (Bulb) of the plastic tubing ( B )

into the compression ﬁ tting.

Pipe clamp

Cold water line

Shut off valve

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (B) (1/4”)

(Not supplied)

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

Shut off valve

Pipe clamp

Cold water line

Water line installation kit

01 SETTING UP

setting up

12_

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

Tighten the compression nut ( B ) onto the

compression ﬁ tting.

Do not over-tighten the compression nut ( B ) .

Turn water on and check for any leakage. If you 2.

ﬁ nd water drops or leakage in the connection

the connections and, if necessary, tighten.

Flush 1 gallon of water through the ﬁ lter 3.

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To ﬂ ush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is ﬁ lled, and then

repeat.

After you turn on the refrigerator, let the ice 4.

maker make ice for 1 to 2 days. Over that

period of time, throw out the ﬁ rst 1 or 2

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the water line,

get a snug, leak-free connection.

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

Make sure your refrigerator is in an appropriate 1.

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

Once the refrigerator is plugged in, make sure 2.

the interior light comes on when you open the

doors.

Set the Temperature control to the coldest 3.

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

After you plug the refrigerator in, it will 4.

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

sufﬁ ciently cool.

CAUTION

You can test the water line quickly using a

paper cup. Under normal conditions, the

about 10 seconds.

Under normal conditions, a 170 cc (5.75 oz.) cup

can be ﬁ lled in about 10 seconds.

_13

operating

Operating your French Door

Refrigerator

( 1 ) Ice Off

Button

( 2 ) Power

Freeze

Button

Speeds up the time needed to freeze

products in the Freezer. It can be helpful

if you need to quickly freeze easily

spoiled items or if the temperature in the

Freezer has warmed dramatically (for

example, if the door was left open).

( 3 )

Freezer

Button

Press the Freezer button to set the

Freezer to your desired temperature. You

can set the temperature between 5°F

(-15°C) and -8°F(-23°C) .

( 4 ) Fridge

Button

Press the Fridge button to set the fridge

to your desired temperature.

You can set temperature between

34°F(1°C) and 44°F(7°C) .

( 5 ) Power

Cool

Button

Speeds up the time needed to cool

products in the Refrigerator. It can be

helpful if you need to quickly cool easily

spoiled items or if the temperature in

the fridge has warmed dramatically (For

example, if the door was left open).

( 6 ) E.

Saver

Button

For better energy efﬁ ciency,

press E.Saver button. However, if

condensation occurs on the door, turn

Press this button for 3 seconds to

switch the temperature units between

°C and °F.

( 7 ) Filter

Indicator

When the ﬁ lter indicator light is on, it is

time to change the ﬁ lter. Typically this

happens about every 6 months.

The ﬁ lter Indicator will be Red when you

have used your water ﬁ lter for 6 months.

COOLING OFF MODE

(“OF & OF” CODE ON THE DISPLAY)

This function is for store display

refrigerators. It is not for customer use.

but doesn’t make cool air. To cancel this

mode, press the Power Freeze and Freezer

buttons at the same time for 5 seconds

until a “Ding-dong” sound is heard and the

unit will now cool.

1 2 3 4 5 67

USING THE CONTROL PANEL

CAUTION

02 OPERATING

The icon will blink red for several

seconds when you open or close the

door.

The ﬁlter indicator will be Off when you

insert the new water ﬁlter.

operating

14_

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands

of water ﬁ lters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTERS.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from the use of a

generic water ﬁ lter. SAMSUNG Refrigerators are

designed to work ONLY WITH SAMSUNG Water

Filter.

The Filter light turns red to let you

know when it is time to change your

water ﬁ lter cartridge.

To give you time to get a new ﬁ lter,

the red light comes on just before the

capacity of the current ﬁ lter runs out.

Changing the ﬁ lter on time provides you with the

freshest, cleanest water from your refrigerator.

ﬁ lter ( 1 ) about 1/4 turn, counter-clockwise.

Pull the water ﬁ lter ( 2. 1 ) from the case ﬁ lter ( 2 ).

To change the water ﬁ lter more easily, t

t

ﬁ lter because impurities in the water cause it

to stick. If you are having difﬁ culties, grip the

water ﬁ lter ﬁ rmly and pull it hard.

t

When you pull the

water ﬁ lter, a little

Sometimes it is hard to disassemble the water

water can leak from

the opening. This is

normal. To minimize

the water leaks, keep

the ﬁ lter cartridge horizontal when you pull it.

yart retl ﬁ retaw eht ytpme ,wo ﬂrevo tneverp oTt

( 3 ) and dry around the ﬁ lter case ( 2 ).

Insert the new ﬁ lter into the ﬁ lter case ( 4

Push the ﬁ lter, and then turn it clockwise until it 4.

locks.

t

ﬁ lter because of high water pressure,

The locked symbol should be lined up

If you have trouble inserting the water

t

with the indicator line.

After removing the old 5.

water ﬁ lter and installing

a new reset the indicator

by pressing the “Fridge”

and “Power Cool” button

simultaneously for about 3

seconds.

on.

For a replacement water ﬁ lter, you can

visit your local home Improvement center

or contact the Samsung Parts distributor.

Be sure the replacement water ﬁ lter has

the SAMSUNG logo on the box and

on the water ﬁ lter. Link : http://www.

samsungparts.com

Removing any residual matter inside

the water supply line after installing

the water ﬁ lter.

Turn ON the main water 1.

supply and supply water

to the refrigerator.

Run 1 Gal of water through

the

dispenser until the

water

runs clear (approx.

6 to 7 minutes). This will

clean

the water supply system and remove air

from the lines.

If after pour 1 Gal the water doesn’t turn clear is

Open the Refrigerator door and make sure 4.

there are no water leaks coming from the

ater ﬁ lter.

Be sure to ﬂ ush the dispenser system thoroughly,

otherwise water may drip fr om the

dispenser.

This means that there is still air in the line.

WARNING

(Red)

_15

operating

Reverse Osmosis Water Supply

IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 35

and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁ ltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi (276 to 414 kPa.) If

the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

Check to see whether the sediment ﬁ lter in the t

reverse osmosis system is blocked. Replace

the ﬁ lter if necessary.

Allow the storage tank on the reverse osmosis t

system to reﬁ ll after heavy usage.

t

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water ﬁ lter.

If you have questions about your water pressure,

call a licensed, qualiﬁ ed plumber.

CONTROLLING THE

TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are 0°F and 37°F(or -18°C and

3°C) respectively. If the temperature of the Freezer

and Refrigerator Compartments are too high or

low, adjust the temperature manually.

CONTROLLING THE

TEMPERATURE

Controlling the Freezer temperature

The Freezer temperature can be set between

5°F(-15°C) and -8°F(-23°C) to suit your particular

needs. Press the Freezer button repeatedly

until the desired temperature is shown in the

temperature display. Keep in mind that foods like

ice cream may melt at 4°F(-15°C).

The temperature display will move sequentially

from -8°F(-23°C) to 5°F(-15°C). When the display

reaches 5°F, it will begin again at -8°F(-23°C).

Five seconds after the new temperature is set, the

display will again show the actual current freezer

temperature until the new temperature is reached.

Controlling the Refrigerator

temperature

The Refrigerator temperature can be set between

44°F(7°C) and 34°F(1°C) to suit your particular

needs. Press the Fridge button repeatedly until the

desired temperature is shown in the temperature

display.

The temperature control process for the Fridge

works just like the Freezer process.

Press the Fridge button to set your desired

temperature. After a few seconds, the Fridge

will begin adjusting towards the newly set

temperature. This will be reﬂ ected in the digital

display.

The temperature of the Freezer or the

Refrigerator may rise from opening the

doors too frequently, or if a large amount of

warm or hot food is placed in either side.

This may cause the digital display to

blink. Once the Freezer and Refrigerator

temperature return to their normal set

temperatures, the blinking will stop.

If the blinking continues, you may need to

“reset” the Refrigerator. Try unplugging the

appliance, wait for around 10 minutes and

then plug the power cord back in.

02 OPERATING

If your refriegerator has a water lter, it may

operating

16_

USING THE COLD WATER

DISPENSER

Using the Water dispenser

(RF261B, RF26H)

Place a glass underneath the

water outlet and push gently

against the water dispenser

lever with your glass. Make

sure the glass is in line with

the dispenser to prevent the

water from splashing out.

If you have just installed the

refrigerator or installed a new

water ﬁ lter, Flush 3 gallons through ﬁ lter before

use (ﬂ ush approximately 6 minutes). Make sure

water ﬂ ows cleanly before drinking.

If you have a long vacation or business trip,

supply to the Refrigerator. This will help

prevent accidental leakages.

Water clouding phenomenon

All water provided to refrigerators ﬂ ows

through the core ﬁ lter which is an alkaline

water ﬁ lter. In this process, the pressure in

the water that has ﬂ owed out of the ﬁ lter

gets increased, and oxygen and nitrogen

become saturated. When this water ﬂ ows

out in the air, the pressure plummets and

the oxygen and nitrogen get supersaturated

so that they turn into gas bubbles. The

water could look misty due to these oxygen

bubbles.The water may look temporarily

cloudy due to these oxygen bubbles. After

a few seconds, the water will look clear.

The water tank’s capacity is approximately

one third (1/3) of a gallon.

Please wait 1 second before removing the

cup after dispensing water to prevent spills.

PUSH

CAUTION

_17

operating

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the refrigerator

When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid

scratching the other door.

If the Vertical Hinged Section is reversed, put it back to the right position and close the door.

Moisture may appear at times on the Vertical Hinged Section.

The door handle may become loose over time. If this happens, tighten the bolts found on the

inside of the door.

If you close one door with a lot of force, the other door may open.

maker for safety reasons.

When the interior or exterior LED lamp has gone out, please contact your service agents.

Tou

Door Bins

Cool Select

Pantry

Digital Sensor Control Auto Door

Closer

Light

Vertical Hinged

Section

Vegetable &

Fruit Drawers

Slide-Shelf

FZ Ice-Maker

Light

Ice Bucket

Auto Pull Out

Drawer

Freezer

Drawer Bin

Internal Water

Dispenser(RF261B)

Quick-Space

Glass Shelf

(on some models)

Ice Maker in Freezer

Test button

02 OPERATING

operating

18_

USING THE COOL SELECT

PANTRY

The Cool Select Pantry is a full-width drawer

with adjustable temperature control. This pantry

can be used for large party trays, deli items, pizza,

beverages or miscellaneous items.

There is a temperature control which can adjust

the amount of cold air allowed into the pantry.

The control is located on the right side of the

pantry.

The Pantry has three modes: The Fresh mode, t

Chilled mode, and Deli mode. Fresh mode is

the default. Press the Temp button repeatedly

until the mode you want is lit. Once you select

a mode, the temperature will change to match

the mode you selected.

The Pantry temperature may change t

depending on the number of items inside

and where they are located, the ambient

temperature, and how often the door is

opened.

The Pantry Selection Button

When you select “Deli”, the temperature of the 1.

pantry will be kept around 41°F (or 5°C). This

feature helps keep food fresh for a long time.

When you select 2.

“Fresh”, the

temperature of the

pantry will be kept

around 38°F (or 3°C).

This feature helps keep

food fresh for a longer

time.

When you select 3.

“Chilled”, the

temperature of the

pantry will be kept around 34°F (or 1°C). This

feature also helps keep meat or ﬁ sh fresh for a

longer time.

The table below lists the Pantry modes and

the kinds of foods that can be stored safely for

each mode.

Deli Fresh Chilled

Pineapple

cucumbers steaks

lemon apples hard cheeses

avocado oranges cold cuts

potato grapes bacon

zucchinis hot dogs

corn

Fruits and vegetables may be damaged

when the “chilled” mode is set.

Do not store lettuce or other leafy produce in this

pantry.

Do not store glass bottles in this pantry. If

they are frozen, they can break and cause

personal injury.

In case you put a water bowl without its

ild into the pantry, condensation may form

around surrounding parts.

REMOVING THE REFRIGERATOR

ACCESSORIES

1. Door Bins & Dairy Compartment

Door Bins

To remove - Simply lift the bin up and pull straight

out.

To relocate

-Slide it in above the desires location and

push down until it stops.

One

CAUTION

_19

operating

Injury may occur if the door bins are not

ﬁ rmly assembled.

Do not allow children to play with the bins. Sharp

corners of the bins may cause injury.

Do not adjust a bin full of food. Remove

the food ﬁ rst.

To remove dust from the bins - Remove the guard

and wash in water.

2. Tempered Glass shelves

To remove - Tilt up the front of the shelf in the

direction shown ( 1 ) and lift it up vertically ( 2 ).

Pull the shelf out.

To relocate - Tilt the front of the shelf up and

guide the shelf hooks into the slots at a desired

height. Then lower the front of the shelf so that the

hooks can drop into the slots.

The Tempered Glass shelves are heavy.

Use special care when removing them.

3. Vegetable & Fruit Drawers

To remove - Pull the drawer out to full extension.

Tilt up the front of the drawer and pull straight out.

To relocate - Insert the drawer into the frame rails

and push back into place.

The drawers need to be removed before

the glass shelf above them can be lifted

out.

4. Cool select pantry

To remove the Cool

select pantry –

Pull the pantry out

to full extension. Tilt

up the front side of

the pantry and pull

straight out.

To relocate the Cool select pantry – Push

the rails to the back of the refrigerator. Place the

drawer onto the rails and slide the pantry back

until it is in place.

To remove the divider – Pull the pantry

completely out to full extension and raise the front

side of the divider to unhook it from the rear wall

of the pantry, then lift the divider out.

To relocate the divider - Hook the back of the

divider over the rear wall of the pantry and push

the divider down.

Using the doors

Ensure that the doors close all the way and are

securely sealed.

When the refrigerator door is only partially open,

it will automatically close. But, the door will stay

open when opened more than the auto close

range and you must close it manually.

REMOVING THE REFRIGERATOR

ACCESSORIES

1. ICE BUCKET

To remove - Lift the ice bucket ( 1 ).

To relocate - Place the ice bucket into the Super

extended drawer ( 2 ).

CAUTION

02 OPERATING

operating

20_

2. Super Extended Drawer

To remove - Pull the drawer out to full extension.

Tilt up the rear of the drawer and lift straight out.

To relocate - Place the drawer onto the rails ( 4 )

by tilting it up. Lower the drawer into place until it

is horizontal and slide the Drawer ( 3 ) in.

3. Freezer Drawer

To remove the freezer drawer - Pull the freezer

drawer out fully. Tilt up the rear of the bin and lift it

out to remove.

To relocate the freezer drawer - Place the bin

into the rail assembly.

Do not allow babies or children go inside

the freezer drawer. They could damage the

refrigerator and seriously injure themselves.

Do not sit on the freezer door. The door

may break. Do not allow children to climb

into the freezer drawer.

Do not remove the divider.

If trapped inside, children may be injured

or suocate to death.

CLEANING THE

REFRIGERATOR

Caring for your Samsung French Door Refrigerator

prolongs the life of your appliance and helps keep

the refrigerator free of odor and germs.

Cleaning the Interior

Clean the inside walls and accessories with a mild

detergent and then wipe dry with a soft cloth. You

can remove the drawers and shelves for a more

thorough cleaning. Just make sure to dry drawers

and shelves before putting them back into place.

Cleaning the Exterior

Wipe the control panel and digital display with

a damp, clean, soft cloth. Do not spray water

directly on the surface of the refrigerator.

The doors, handles and cabinet surfaces should

be cleaned with a mild detergent and then wiped

dry with a soft cloth. To keep your appliance

looking its best, polish the exterior once or twice a

year.

Do not spray water directly on the

refrigerator. Use a clean, damp cloth to

clean.

Do not use benzene, thinner, or Clorox for

cleaning. They may damage the surface of

the appliance and may cause a ﬁ re.

You can erase the printed

letters on the display if you

apply stainless cleaner directly

to the area where the letters

are printed.

CAUTION

WARNING

CAUTION

La page charge ...

Samsung RF26HFP Series Manuel utilisateur

Marque: Samsung

Modèle: RF26HFP Series

Catégorie: Frigos

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung RF26HFP Series User manual
español: Samsung RF26HFP Series Manual de usuario

Samsung RF26HFP Series Manuel utilisateur

Ce manuel convient également à

Samsung RF26HFP Series Manuel utilisateur

dans d''autres langues

Documents connexes