Ground Zero GZIA 1.1000DXII Le manuel du propriétaire

Catégorie
Amplificateurs audio de voiture
Taper
Le manuel du propriétaire

Ce manuel convient également à

IRIDIUM-SERIES
AMPLIFIER
OWNER’S MANUAL
GZIA 1.1000DX-II
Features
Class D Mono Amplifier
1 Ohm stable
Power & Protection indicator
Bass Boost 0 12 dB (45z)
Variable lowpass
Phaseshift switch 0 / 180°
Auto-On @ High Level Input
Adjustable input sensitivity
Soft delayed remote turn- on
Bass remote
Thermal / Short / Overload protection
- 2 -
Tools and materials you need
Screwdriver
Electric drill, 3 mm / 0.12” carbide drill bit
Mounting screws
Power wire min. 20 mm²
Ground wire min. 20 mm²
Speaker wire min. 2 x 2,5 mm²
Please note!
As a precaution it is advisable to disconnect the vehicle’s battery before making connection
to the +12 Volts supply wiring (see owner’s manual of your car for further information).
Please use great caution drilling your trunk. Your gas tank and brake lines can be damaged by puncturing with your drill bit
this could cause damage or failure of your cars operating systems.
Never pass wires over sharp angles. It is recommended to buffer the power supply of the amplifier with a capacitor min. 1
Farad to guarantee a stable operation voltage.
WARNING !
High powered audio systems in a vehicle are capable of generating "Live Concert" levels of sound pressure. Continued exposure to
excessively high volume sound levels may cause hearing loss or damage. Also, operation of a motor vehicle while listening to audio
equipment at high volume levels may impair your ability to hear
external sounds such as; horns, warning signals, or emergency vehicles, thus constituting to a potential traffic hazard. In the interest of
safety, Consumer Electronics recommends listening at lower volume levels while driving.
Planning your system
Before beginning the installation, consider the following:
a. If you plan to expand your system by adding other components sometime in the future, ensure adequate space is left, and
cooling requirements are met.
b. If your radio / source is equipped with pre-amp RCA outputs, we recommend to use them.
Mounting your amplifier
a. Select a suitable location that is convenient for mounting, is accessible for wiring
and has ample room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes, remove the amplifier.
Warning
Chose a mounting position where all eclectic wires are protected from being damaged by sharp edges, heat or other conditions. +12Volt
DC electrical connections must be fused on the battery side. Make sure your radio and all other devices will be turned off while connection
your system.
If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the system. Using a fuse of different type or
rating may result in damage to this system which isn’t covered by the warranty.
- 3 -
Controls and functions
- 4 -
Controls and functions
1
Speaker terminals
For connection of the speakers
2
Power terminals
GND -> Ground connection
REM -> Remote antenna terminal [Not for use with High level inputs (5)]
BATT -> +12 Volt
3
Satus indication
GREEN OK
RED Error
4
Cinch inputs
Terminal for connection of the RCA wires.
To avoid failure, please use high quality RCA wires.
IMPORTANT!
Do not use the High level inputs and the Cinch inputs parallel, this can
damage the amplifier. Use either the Cinch OR the High Level inputs.
5
High Level inputs
These inputs must be used if your head unit is not equipped with a Low
Level Cinch ouput.
Connect this input to the speaker outputs of your head unit. The amplifier
automatically turns on as soon as a signal is received (Auto On). The
remote connection of the Power- Terminal (2) won’t be used.
IMPORTANT!
Do not use the High level inputs and the Cinch inputs parallel, this can
damage the amplifier. Use either the Cinch OR the High Level inputs.
6
Phase shift controller
This controller allows you to fit the subwoofer channel in-phase to the front
system.
7
Low Pass controller
Only frequencies from 30Hz to 250Hz will be reproduced (depending on
the LPF filter controller position). Set the filter switch to „LOW“ position.
Adjust the variable LPF frequency to the desired frequency using the
controller.
9
Remote control input
For connection of bass remote control
10
Input level controller
With this controller you can adjust the input sensitivity
11
Bass Boost controller
For adjusting a Bass Boost at 45 Hz from 0 12 dB
High Level Input
Depending on the configuration of your car and sound system, error noises may appear when using the high level inputs. Please use the
additional middle ground-connection of this input to reduce these noises.
The Auto-On function allows you to use the amplifier without an additional remote connection. This makes it possible to operate it with an
OEM headunit and OEM active systems, which are not equipped with cinch ouputs or switched remote-outputs.
- 5 -
High Level Input
Depending on the configuration of your car and sound system, error noises may appear when
using the high level inputs.
Please use the additional middle ground-connection of this input to reduce these noises.
Connect this wire to the GND powerterminal.
A connection to the GND connection of the signal source can also be useful.
The Auto-On function allows you to use the amplifier
without an additional remote connection.
The remote terminal will not be used.
- 6 -
Turning on the amplifier
The amplifier automatically turns on a few seconds after you turn on your radio.
Note: Your amplifier temporarily shuts down if it gets too hot, then restarts automatically once it cools
(At about 80° / 176° F).
Adjusting the audio level
1. LEVEL (Min/Max): Turn fully counter- clockwise to MIN position
2. Turn the auto sound system's volume control to about two-third of its full range.
3. Adjust LEVEL to a comfortable listening level.
- 7 -
Stereo Wiring
- 8 -
Specifications
Model
GZIA 1.1000DX-II
Type
1 Channel Class D
RMS Power @ 4
CEA Standard CEA-2006-A
1 x 350 W (1% THD+N)
RMS Power @ 2
CEA Standard CEA-2006-A
1 x 650 W (1% THD+N)
RMS Power @ 1
CEA Standard CEA-2006-A
1 x 1000 W (1% THD+N)
MAX Power
CEA Standard CEA-2006-A
1 x 1200 W (10% THD+N)
Damping factor
> 100
Lowpass
30 Hz 250 Hz
Bass Boost
0 ~ +12 dB (45 Hz)
Frequency response
5 Hz 250 Hz (± 1 dB)
Input sensitivity
200 mV – 6 V (± 5%)
Bass remote control
Auto-On @ High Input
Fuse
2 x 40A
Dimensions
W x H x L mm
192 x 49 x 302
Dimensions
W x H x L inch
7.56“ x 1.93“ x 11.89
- 9 -
Trouble shooting guide
Symptoms
Cure
No sound
Is the POWER LED illuminated?
Check fuses in amplifier.
Be sure remote lead is connected.
Check tuner/deck volume level.
Check for speaker short or amplifier overheating
Amp not switching on
Check power wire or connections
Check connections to radio
No sound in one
channel
Inspect for short circuit or an open connection
Check audio leads
Reverse left and right RCA inputs to determine if it is
occurring before the amp
Amp turning off at
medium / high volume
Check speaker load impedance
Be sure proper speaker load impedance
recommendations are observed
(If you use an ohm meter to check speaker
resistance, please remember that DC resistance and
AC impedance may not be the same.)
Protection LED is on
Turn radio volume down
Separate speaker wires and insulate
Die Gewährleistung entspricht der gesetzlichen Regelung. Eine Rücksendung kann nur nach vorheriger Absprache und in der
Originalverpackung erfolgen. Bitte unbedingt einen maschinell erstellten Kaufbeleg und eine Fehlerbeschreibung beilegen. Von der
Gewährleistung ausgeschlossen sind Defekte, die durch Überlastung, unsachgemäße Behandlung oder bei Teilnahme an Wettbewerben
entstanden sind. Wir behalten uns das Recht vor, zukünftig nötige Änderungen oder Verbesserungen an dem Produkt vorzunehmen ohne
den Kunden darüber zu informieren.
Limited warranty - defective products must be returned in original packaging - please add a copy of the original purchasing invoice showing
the purchasing date and a detailed description of the failure. Failure caused by overload, misuse or by using the product for competition
purpose are not covered by the warranty. We reserve the right to make needed change or improvement to the product without informing
customer about this in advance.
De Garantie bepalingen van alle door ground zero geleverde producten is volgens wettelijke
bepalingen geregeld, Een retourzending kan alleen na duidelijke afspraak en in de originele
verpakking plaatsvinden.SVP een aankoopbon en een duidelijke storingsomschrijving bijvoegen.Van garantie uitgesloten zijn defecten door
overbelasting, onkundig gebruik, of door deelname aan wedstrijden (SPL) ontstaan zijn. Wij behouden ons het recht om de nodige
veranderingen of verbeteringen aan het product door te voeren zonder de klant hierover te informeren.
La garantie est conforme aux droits légaux. Un retour du produit défectueux doit être dans son
emballage d'origine sur présentation du reçu ou de la facture indiquant la description du defaut.La présente Garantie n'est pas applicable
lorsque le produit a été endommagé en raison: Mauvaise alimentation, Trop de puissance (HP,Subwoofer) Accident, Installation ou
Utilisation non conforme aux normes Technique (Concours SPL etc). Nous nous réservons le droit d'entreprendre à l'avenir nécessairement
des modifications ou des
améliorations au produit sans informer le client.
Ground Zero GmbH
Erlenweg 25, 85658 Egmating, Germany
Tel. +49 (0)8095/873 830 Fax -8310
www.ground-zero-audio.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Ground Zero GZIA 1.1000DXII Le manuel du propriétaire

Catégorie
Amplificateurs audio de voiture
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues