Simplicity 076045-01 Guide d'installation

35kW 3 Phase Installation

& Start-Up Manual

Generator Systems

35000 Watt

3 Phase Generator System

Series 35000

This generator is rated in accordance with UL (Underwriters Laboratories) 2200 (stationary engine generator assemblies) and CSA (Canadian Standards

Association) standard C22.2 No. 100-4 (motors and generators).

80014429 Rev -

2

Thank you for purchasing this quality-built GE generator. We are pleased that you’ve placed your confidence in the

GE brand. When operated and maintained according to the instructions in the operator’s manual, your generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby

generators and how to avoid them. This product is only for use as an optional generator system which provides an

alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication

systems that, when stopped during any power outage, could cause discomfort or inconvenience. Only models equipped

with the MRS19 controller qualify for either an emergency standby or legally required standby system as defined by

NFPA 70 (NEC). For complete information on these types of installations, consult NFPA 70 and NFPA 110.

Save these original instructions for future reference.

This generator system requires professional installation before use. The installer should follow the instructions

completely.

Where to Find Us

You never have to look far to find support and service for your generator. Consult your Yellow Pages. There

are many GE authorized service dealers worldwide who provide quality service. You can also contact GE

Customer Service by phone at 888-575-8226 between 8:00 AM and 5:00 PM CT., or click on Find a Dealer at

www.standbygeneratorsystems.com, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase

issues.

Date of Purchase

Generator

Model Number

Model Revision

Serial Number

3 3

Table of Contents

Important Safety Instructions........................4

Installation ....................................7

Owner Responsibilities.........................................7

Installing Dealer/Contractor Responsibilities ........................7

Installation Checklist ..........................................8

Generator Placement ..........................................9

Exhaust Side of Generator ......................................9

Placement of Standby Generator to

REDUCE THE RISK OF CARBON MONOXIDE POISONING ............10

Other General Location Guidelines...............................11

Placement of Standby Generator to REDUCE THE RISK OF FIRE .......12

Concrete Slab (Required)

At the appropriate location, construct a concrete slab: . . . . . . . . . 14

Fuel Conversion .............................................18

Fuel Pressure ...............................................18

Power Loss ................................................18

Power Connections ..........................................19

Grounding the Generator ......................................22

Final Installation Considerations ................................22

Initial Start-up (No Load)......................................23

Controls ..................................... 24

Operation .................................... 24

Automatic Operation Sequence .................................24

Setting Exercise Timer ........................................24

Installation Inspection ........................................24

4

Save These Instructions

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and

batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE addresses practices not related to personal

injury.

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard. The

warnings in this manual, and the tags and decals affixed

to the unit are, therefore, not all-inclusive. If you use a

procedure, work method or operating technique that

the manufacturer does not specifically recommend, you

must satisfy yourself that it is safe for you and others.

You must also make sure that the procedure, work

method or operating technique that you choose does not

render the generator system unsafe.

Fire

Toxic Fumes

Explosive Pressure

Rotating Fan Blade

Lift Hazard Read Manual

Exploding BatteryRotating Belt/Pulley

Chemical BurnAuto Start

Hot SurfaceRotating Parts

Electrical ShockExplosion

WARNING The engine exhaust from this product

contains chemicals known to the State of California

to cause cancer, birth defects, or other reproductive

harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the

State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result

in death, serious injury, headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea

or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventailation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow

exhaust gas to enter inside or be drawn into a

potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Slightest spark will ignite

hydrogen and cause explosion,

resulting in death or serious

injury.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery contents could cause severe

chemical burns.

A battery presents a risk of electrical shock and high

short circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit

cigarette during and for several minutes after

charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots

and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

5

WARNING Generator produces hazardous

voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility power

could result in death or serious injury to electric

utility workers due to backfeed of electrical

energy.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or

feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk of

a shock hazard.

• DO NOT allow unqualified persons or children to

operate or service generator.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical power

and contact the local authorities. Avoid direct contact

with the victim.

• Despite the safe design of the generator, operating

this equipment imprudently, neglecting its

maintenance or being careless could cause possible

injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• Before performing any maintenance on the

generator, disconnect the battery cable indicated by

a NEGATIVE, NEG or (-) first. When finished, reconnect

that cable last.

• After your system is installed, the generator may crank

and start without warning any time there is a power

failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely

flammable and explosive, which could

cause burns, fire or explosion resulting in

death or serious injury.

• Install the fuel supply system according to NFPA 37

and other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak tested.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any

oil spills immediately. Ensure that no combustible

materials are left in the generator compartment. Keep

the area near the generator clean and free of debris.

WARNING Exhaust heat/gases could ignite

combustibles or structures resulting in

death or serious injury.

Contact with muffler area could cause

burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be

at least 5 ft. (1.5m) from windows, doors, any wall

opening, shrubs or vegetation over 12 inches (30.5 cm)

in height.

• Standby generator weatherproof enclosure must have

a minimum of 5 ft. (1.5 m) overhead clearance from

any structure, overhang, or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect provided

fuel line to generator. DO NOT use with or substitute

any other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator

cooling and maintenance clearances.

WARNING Hazardous Voltage - Contact with power

lines could cause electric shock or burns,

resulting in death or serious injury.

Lifting Hazard / Heavy Object - Could

result in serious injury.

• If lifting or hoisting equipment is used, DO NOT contact

any power lines.

• DO NOT lift or move generator without assistance.

6

CAUTION Installing the 15A fuse could cause the

engine to start at any time without warning

resulting in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed from

the control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring

has been completed and inspected.

WARNING Moving parts could crush and cut.

Starter and other rotating parts

could entangle hands, hair, clothing,

or accessories resulting in serious

injury.

• NEVER operate generator without protective housings,

covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control

panel and disconnect Negative (NEG or -) battery

cable.

WARNING Hot pressurized coolant could cause

serious injury.

• DO NOT open radiator cap when hot.

• Before servicing, allow coolant to cool.

CAUTION Excessively high operating speeds could

result in minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on

generator.

• DO NOT tamper with governed speed. Generator

supplies correct rated frequency and voltage when

running at governed speed.

• DO NOT modify generator in any way.

NOTICE Improper treatment of generator could

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact

your authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating

air is critical for correct generator operation.

• The access panels/doors must be installed whenever

the unit is running.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a

step. Stepping on the unit could cause stress and

break parts. This may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively or makes unusal noises.

NOTICE Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• Start generator and let engine stabilize before

connecting electrical loads.

7

Installation

Equipment Description

This product is only for use as an optional generator

system which provides an alternate source of electric

power and to serve loads such as heating, refrigeration

systems, and communication systems that, when

stopped during any power outage, could cause

discomfort or inconvenience.

NOTICE Only models equipped with the MRS19 controller

qualify for either an emergency standby or legally

required standby system as defined by NFPA 70 (NEC).

For complete information on these types of installations,

consult NFPA 70 and NFPA 110.

• Emergency generator systems are intended to

automatically supply illumination, power, or both,

to designated areas and equipment in the event of

failure of the normal supply. Emergency systems

may also provide power for such functions as

ventilation where essential to maintain life, where

current interruption of the normal supply would

produce serious life safety or health hazards.

• Legally Required standby generator systems

are intended to automatically supply power to

selected loads in the event of failure of the normal

source which could create hazards or hamper

rescue or fire-fighting operations.

Every effort has been made to ensure that information

in this manual is accurate and current. However, we

reserve the right to change, alter, or otherwise improve

the product and this document at any time without prior

notice.

Only current licensed electrical and plumbing

professionals should attempt generator system

installations. Installations must strictly comply with

all applicable codes, industry standards laws and

regulations.

Owner Responsibilities

• Read and follow the instructions given in the

operator’s manual.

• Follow a regular schedule in maintaining, caring

for and using your generator, as specified in the

operator’s manual.

Installing Dealer/Contractor Responsibilities

• Read and observe the safety rules.

• Install only an UL approved transfer switch that is

compatible with the generator.

• Read and follow the instructions given in this

installation and start-up manual.

Unpacking Precautions

The unit is shipped ready for installation on a prepared

reinforced cement slab or engineered base. Avoid

damage from dropping, bumping, collision, etc. Store and

unpack carton with the proper side up, as noted on the

shipping carton.

Delivery Inspection

After removing the carton, carefully inspect the

generator for any damage that may have occurred

during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight

bill and affix his signature under the consignor’s memo of

loss or damage. If loss or damage is noted after delivery,

separate the damaged materials and contact the carrier

for claim procedures. Missing or damaged parts are

not warranted.

Shipment Contents

The generator system is supplied with:

• Fully-serviced coolant system

• Fully-serviced oil/lubricating system

• Flexible fuel hook-up hose

• Installation and Operator’s manual

• Spare access door keys

• Touch up paint

Not Supplied:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Reinforced concrete pad

• Connecting wire and conduit

• Fuel supply valves/plumbing

• Two 60” lengths of 2” Schedule 40 pipe (NOT

conduit)

• Crane, lifting straps, chains or cables

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

• Various special tools and equipment

8

Installation Checklist

Carbon Monoxide (CO) Detector

Carbon Monoxide (CO) detector installed and in working

order.

Smoke detector(s) installed and in working order.

Placement

Required permits have been obtained.

Generator placed in an area free from Carbon Monoxide

(CO) buildup. See Placement of Standby Generator to

Reduce the Risk of Carbon Monoxide Poisoning.

Generator placed in an area compliant to NFPA 37. See

Placement of Standby Generator to Reduce the Risk

of Fire.

Generator placed in an area free from water damage.

See Other General Location Guidelines.

Generator placed in an area free from utility and other

home systems. See Other General Location Guidelines.

Generator placed in a debris free zone. See Other

General Location Guidelines.

Generator placed on flat ground with provisions

for water drainage. See Other General Location

Guidelines.

Fuel

Generator is connected to fuel source with flexible fuel

line, has no fuel leaks and conforms to local codes. See

The Gaseous Fuel System.

Proper fuel pressure has been measured with all gas

appliances operating. See The Gaseous Fuel System.

Fuel system has been configured for the proper fuel

supply: Natural gas (NG) or liquefied petroleum ( LP). See

Fuel Conversion.

Fuel type: (circle one) NG LP

Fuel pipe size used: (circle one) 3/4” 1” 1-1/4” 1-1/2”

See NFPA 54, Chapter 6.

Fuel pressure at fuel inlet port with generator on and at

full load and all gas appliances turned on and operating

____________________.

Electrical

Generator neutral is connected to Automatic Transfer

Switch. See Generator AC Connection System.

Generator is grounded. See Grounding the Generator

and NFPA 70,NEC, Article 250.35B.

Generator is connected to the transfer switch with the

specified wiring. See Utility Circuit Connection and

Transfer Switch Communication.

Generator is connected to the transfer switch with

the specified wiring. #18AWG twisted pair wiring from

the generator control panel to the transfer switch is

installed in a separate conduit from high voltage wires

unless the insulation rating on all wiring is rated for

600V. See Transfer Switch Communication.

Dipswitches in most transfer switches must be set

to correspond to the wattage of the generator. See

Transfer Switch Operator/Installation Manual.

Operation

Cold weather kit is installed in temperatures below 30°F

(4°C). See Cold Weather Kit.

Correct battery type is installed and fully charged. See

Final Installation Considerations.

Generator engine oil level is at full mark. See Final

Installation Considerations.

Circuit breaker is in the ON position.

Utility was shut off to test the operation of generator

and transfer switch. Note any fault codes and make

corrections as required.

AC Voltage Output___________________________.

Frequency Output___________________________.

Owner Information

Name: ___________________________________________

Address: _________________________________________

Phone/e-mail: _____________________________________

Unit Information

Generator Model: __________________________________

Generator Serial Number: ___________________________

Installing Contractor Information

Name: ___________________________________________

Address: _________________________________________

Phone/FAX: _______________________________________

Electrician: _______________________________________

Signature: ________________________________________

Plumber: _________________________________________

Signature: _______________________________________

Inspector Information

Name: ___________________________________________

Address: _________________________________________

_________________________________________________

Title: _____________________________________________

Inspection Date: ___________________________________

This generator has been installed per the manufacturer’s

instructions:

Installing Contractor Signature: ___________________________

Date: _________________________________________________

Proper installation of the home generator requires the completion of the following tasks:

9

Before installing the generator, consult with the owner

and convey the following requirements, which must be

satisfied before the installation is complete.

There are two equally important safety concerns in

regards to carbon monoxide poisoning and fire. There

are also several general location guidelines that must

be met before the installation is considered complete.

Generator Placement

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness, vomiting,

confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventailation intakes, soffit vents, crawl spaces, open garage

doors or other openings that can allow exhaust gas to

enter inside or be drawn into a potentially occupied building

or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

Exhaust Side of Generator

A Exhaust outlet side of weatherproof enclosure

B Weatherproof enclosure opposite exhaust side

A

B

10

Placement of Standby Generator to REDUCE THE RISK OF CARBON MONOXIDE POISONING

The figure below demonstrates POTENTIAL points of entry for Carbon Monoxide Gas.

All fossil fuel burning equipment, such as standby

generators, contains carbon monoxide (CO) gas in

the engine exhaust. CO gas is odorless, colorless and

tasteless and is unlikely to be noticed until a person is

overcome. CO gas can kill you so it is required that the

following is included as part of the installation:

• Install generator outdoors in an area that will not

accumulate deadly exhaust gas.

• DO NOT install generator where exhaust gas

could accumulate and enter inside or be drawn

into a potentially occupied building or structure.

• By law it is required in many states to have a

Carbon Monoxide (CO) detector in operating

condition in homes and other structures occupied

by people. Carbon monoxide detector(s) (A)

MUST be installed and maintained indoors

according to the manufacturer’s instructions /

recommendations. A CO monitor is an electric

device that detects hazardous levels of CO. When

there is a buildup of CO, the monitor will alert the

occupants by flashing visual indicator light and

alarm. Smoke alarms cannot detect CO gas.

• Nearby structures may be exposed to the engine

exhaust from your standby generator and must

be considered when installing your standby

generator.

• Ensure exhaust gas is kept away from:

B overhead doors

C doors

D windows (not shown)

E other openings that can allow exhaust gas to

enter inside or be drawn into a potenially occupied

building or structure.

A

C

B B

11

• Direct the standby generator exhaust away from

or parallel to the building or structure. DO NOT

direct the generator exhaust towards a potentially

occupied building, structure, windows, doors,

ventilation intakes, soffit vents, crawl spaces,

open garage doors or other openings where

exhaust gas could accumulate and enter inside or

be drawn into a potentially occupied building or

structure.

• DO NOT place standby generator in any area

where leaves or debris normally accumulates.

Position standby generator in an area where

winds will carry the exhaust gas away from any

potentially occupied building or structure.

Other General Location Guidelines

• Place the standby generator in a prepared

location that is flat and has provisions for water

drainage.

• Install the standby generator in a location

where sump pump discharge, rain gutter down

spouts, roof run-off, landscape irrigation, or

water sprinklers will not flood the unit or spray

the enclosure and enter any air inlet or outlet

openings.

• Install the standby generator where it will not

affect or obstruct any services (including covered,

concealed and underground), such as telephone,

electric, fuel (natural gas / LPG vapor), irrigation,

air conditioning, cable, septic, sewer, well and so

forth.

• Install the standby generator where leaves,

grass, snow, etc will not obstruct air inlet and

outlet openings. If prevailing winds will cause

blowing or drifting, you may need to construct a

windbreak to protect the unit.

12

Placement of Standby Generator to REDUCE THE RISK OF FIRE

The National Fire Protection Association (NFPA)

standard NFPA 37 establishes criteria for minimizing

the hazard of fire during the installation and operation

of stationary combustion engines. NFPA 37 limits the

spacing of an enclosed generator from openings in

walls, structures and combustible materials outside the

enclosure.

The placement requirements provided are based on

compliance to NFPA 37 2010 section 4.1.4.

WARNING Exhaust heat/gases could ignite combustibles

or structures resulting in death or serious injury.

• Exhaust outlet side of weatherproof enclosure must have

at least 5 ft (1.5 m) minimum clearance from any structure,

shrubs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft (1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from any

structure, overhang or trees.

• DO NOT place weatherproof enclosure under a deck or

other type of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided

fuel line to generator, DO NOT use with or substitute any

other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot detect

smoke.

• DO NOT place weatherproof enclosure in manner other

than shown in illustrations.

Examples of standby generator locations to reduce

the risk of fire:

Legend for Generator Locations to reduce the risk of

fire.

A Standby weatherproof enclosure must be at

least 5 ft (1.5 m) from windows, doors, any wall

opening, shrubs or vegetation over 12 inches (30.5

cm) in height.

B Exhaust outlet side of weatherproof enclosure

must have at least 5 ft (1.5 m) minimum clearance

from any structure, shrubs, trees or any kind of

vegetation.

C Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance

from any structure, overhang or trees.

NOTICE DO NOT place weatherproof enclosure under

a deck or other type of covered structure that may

confine airflow.

Vertical and Horizontal Clearances

A

B

C

13

Legend for Generator Locations to reduce the risk of

fire.

A Standby weatherproof enclosure must be at

least 5 ft (1.5 m) from windows, doors, any wall

opening, shrubs or vegetation over 12 inches (30.5

cm) in height.

B Exhaust outlet side of weatherproof enclosure

must have at least 5 ft (1.5 m) minimum clearance

from any structure, shrubs, trees or any kind of

vegetation.

Typical Installations

NOTICE The figures below show the minimum installation distances allowed to structures and items listed in legend.

C Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

NOTICE DO NOT place weatherproof enclosure under a

deck or other type of covered structure that may confine

airflow.

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

B

A

B

A

B

A

B

14

Concrete Slab (Required)

At the appropriate location, construct a concrete slab:

• 28 day compression strength of 3000 psi (200 MPa)

• Minimum 5” (13cm) thick

• Minimum 6” (15cm) wider than enclosure on all

sides (shown as D in figure)*

• Strengthen slab with No. 6 reinforcing bars (on 12”

(30.5cm) centers) or 8 ga. steel wire fabric

(6” (15cm) centers).

Avoid placing reinforcement in entrance stub-up area

(shown as B).

Attach unit to slab at four corner locations (A) with

minimum 5/16” diameter (8mm) (per local requirements)

masonry anchor bolts long enough to secure the unit.

The fuel inlet location (C),the concrete slab, and the

exhaust outlet (E) are shown for reference.

• The standby generator enclosure (F)measures

82” (208 cm) X 37” (94 cm).

A Holes located in base to anchor to pad

B Stub up Area

C Fuel Inlet

D Concrete slab

E Exhaust Outlet

F Standby Generator Enclosure

B

C

D

E

A

F

15

Electrical and Fuel Inlet Locations

A through-slab power cable stub-up is preferred. If

stub-up’s are not used, (B) indicates the recommended

location for punching holes for attaching power conduit.

The 1 inch N.P.T. fuel inlet connector (A) is shown for

reference.

Lifting the Generator

The generator weighs approximately 2500 pounds

(680 kg). Proper tools, equipment and qualified personnel

should be used in all phases of handling and moving the

generator.

Remove circuit breaker box bottom plate prior to

positioning generator. Two 60” (1.5m) lengths of 2”

Schedule 40 pipe (C), supplied by the installer, are required

to lift the generator onto cement pad. Insert pipes through

the lifting holes (D) located near the unit’s base. Use a

spreader bar to ensure that the chains, straps or cables

DO NOT touch the generator’s roof. Retouch any chipped

paint with supplied touch-up paint.

A

B

WARNING Hazardous Voltage - Contact with power

lines could cause electric shock or burns,

resulting in death or serious injury.

Lifting Hazard / Heavy Object - Could

result in serious injury.

• If lifting or hoisting equipment is used, DO NOT contact

any power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

C

D

16

Access Ports

The generator is equipped with an enclosure that has

several access doors, as shown above. The doors are

named for a significant component located behind them,

as follows:

A - Fuel Inlet port (shown for reference)

B - Control Panel door (may be two doors)

C - Exhaust opening (shown for reference)

D - Coolant/Oil Fill door

E - Battery door

F - Muffler door

The Coolant Fill, Battery and Control Panel doors must

be installed whenever the unit is running to assure

proper cooling, reduce noise and for added safety. The

enclosure also includes muffler and radiator access

panels, used only for cleaning those components. Those

panels should remain closed at all other times.

Each generator is shipped with a set of identical keys.

These keys fit the locks that secure the access ports.

To open access door:

1. Insert key into lock of access door handle and turn

key one quarter turn counterclockwise.

2. Grasp door’s handle and turn one quarter turn

counterclockwise to open. Remove key.

3. Coolant Fill door is unlocked in the same manner. It

can be used for adding coolant or oil.

To close access door:

1. Close door and turn door’s handle one quarter

turn clockwise.

2. Insert key into lock of door handle and turn key one

quarter turn clockwise. Remove key.

WARNING Contact with muffler area could cause

burns resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

B

A

C

D

E

F

17

The Gaseous Fuel System

The information below is provided to assist gaseous

fuel system technicians in planning installations. In no

way should this information be interpreted to conflict

with applicable fuel gas codes. Consult with your local

fuel supplier or Fire Marshall if questions or problems

arise.

TO THE INSTALLER: Consult with the generator owner(s)

and convey any technical considerations that might

affect their installation plans before applying these

general guidelines.

The following general rules apply to gaseous fuel

system piping:

• The piping should be of a material that conforms

to federal and local codes, rigidly mounted and

protected against vibration.

• Piping should be protected from physical damage

where it passes through flower beds, shrub beds,

and other cultivated areas where damage could

occur.

• Install the flexible, gaseous hose (B) (supplied)

between the generator fuel inlet port (A) and rigid

piping to prevent thermal expansion or contraction

from causing excessive stress on the piping

material.

• A union (C) or flanged connection shall be provided

downstream to permit removal of controls.

• A manometer port should be provided (D). A

digital manometer, P/N 19495, is available at your

GE service center. When the initial test runs are

completed, the manometer is removed and the port

is plugged. The manometer port permits temporary

installation of a manometer to ensure that the

engine receives the correct fuel pressure to operate

efficiently throughout its operating range.

• Where the formation of hydrates or ice is known to

occur, piping should be protected against freezing.

The termination of hard piping should include a

sediment trap (E) where condensate is not likely to

freeze.

• A minimum of one accessible, approved manual

shutoff valve (F) shall be installed in the fuel supply

line within 6 ft (180 cm) of the generator.

• A manual fuel shut-off valve located in the interior

of the building.

• Where local conditions include earthquake,

tornado, unstable ground, or flood hazards, special

consideration shall be given to increase strength

and flexibility of piping supports and connections.

• Piping must be of the correct size to maintain the

required supply pressures and volume flow under

varying generator load conditions with all gas

appliances connected to the fuel system turned on

and operating.

• Use a pipe sealant or joint compound approved for

use with NG/LPG on all threaded fittings to reduce

the possibility of leakage.

• Installed piping must be properly purged and

leak tested, in accordance with applicable codes

and standards.

A Generator Fuel Inlet

B Flexible Fuel Hose

C Union Fitting

D Manometer Test Port

E Sediment Trap

F Manual Shut-off Valve

NOTICE The supplied flexible gaseous pipe is not to be

installed underground or in contact with the ground.

• The entire flexible gaseous pipe must be visible

for periodic inspection and must not be concealed

within nor contact nor run through any wall, floor, or

partition.

WARNING Propane

and Natural Gas are extremely

flammable and explosive, which could

cause burns, fire or explosion resulting in

death or serious injury.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in

high areas.

• The slightest spark could ignite these fuels and cause

an explosion.

• DO NOT light a cigarette or smoke.

A

B

C

D

E

F

18

Fuel Pipe Sizing

There are numerous on-line or otherwise-published

references for fuel pipe sizing. For example, NFPA 54

- National Fuel Gas Code, 2006 (Item #: 320-6031-06)

is a common resource. The installer should consider

the specific gravity of gas, compensate for a nominal

amount of restriction from bends and fittings, and refer

to federal and local codes for guidance.

Fuel Conversion

The unit is shipped from the factory calibrated for NG

operation. To convert the engine from NG to LP vapor,

locate the fuel selector switch (A) and move the selector

switch to either LP or NG.

Fuel Pressure

Both LP vapor and natural gas fuel supply pressure at

the generator’s fuel inlet port should be between 7 to 11

inches (18 to 28 cm) of water (in. W.C.) at full load with

all gas appliances turned on and operating. Maximimum

pressure drop from static (engine not running) to full load

is 0.5 in. W.C. Maximum pressure with engine OFF at No

Load is 13.85 in. W.C.

Power Loss

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will

decrease 3% for each 1,000 feet (300 m) above sea

level and 1% for each 10° F (5.6°C) above 77°F (25°C).

Generators located in these conditions, that use power

management technology must have their transfer switch

programmed appropriately for this power decrease.

Fuel Consumption

Estimated fuel supply requirements at half and full load

for natural gas and LP vapor fuels are shown here.

Physical Properties LP Vapor Natural

Gas

Normal Atmospheric

State

Gas Gas

Boiling Point (in °F):

Initial

End

-44

-259

Heating Value:

BTU per gallon (Net LHV*)

BTU per gallon (gross**)

Cubic feet (gas)

83,340

91,547

2,500

63,310

1,000

Density*** 36.39 57.75

Weight† 4.24 2.65

Octane Number:

Research

Motor

110+

97

110+

* LHV (Low Heat Value) is the more realistic rating.

** Gross heat value does not consider heat lost in the form of

water during combustion.

*** Density is given in “Cubic Feet of Gas per Gallon of Liquid”.

† Weight is given in “Pounds per Gallon of Liquid”.

35kW LP Vapor Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 396150 252887 113955

CF/ph 159 101 46

m³/ph 4.5 2.8 1.3

GAL/hr 4.4 2.8 1.3

32kW Natural Gas Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 344452 209571 105011

CF/ph 345 210 105

m³/ph 9.8 5.9 3.0

A

19

Series 35000* Voltage Rated Amps Wire Size

3 Phase Wye

120/208 121 1/0

3 Phase Wye

139/240 105 1 AWG

3 Phase Delta

120/240 105 1 AWG

3 Phase Wye

240/416 61 4 AWG

3 Phase Wye

277/480 53 6 AWG

3 Phase Wye

346/600 42 8 AWG

A - Power Connection (Line 1, Line 2 and Line 3) —

Power connection to transfer switch.

B - Neutral and/or Ground Connection — Connect

to transfer switch neutral and ground.

For system connections such as remote start, e-stops

and controller inputs and outputs, please refer to the

connection diagrams on the following pages.

Power Connections

Compare this illustration with your generator to familiarize yourself with the location of these connections.

• For power output connection, use 300 volt, 167 °F-194 °F

(75 °C-90 °C) wire. See chart on right for proper wire size.

• For Utility Circuit connection use #14 AWG minimum 300

volt, 167 °F-194 °F (75 °C-90 °C) wire.

• For transfer switch communication use #18 AWG twisted

pair conductors, no greater than 200 ft (60 m) in length,

300 volt, 167 °F-194 °F (75 °C-90 °C) wire.

*Refer to Generator Data Tag to determine series of generator.

A

B

20

La page charge ...

Simplicity 076045-01 Guide d'installation

Simplicity 076045-01 Guide d'installation

dans d''autres langues

Autres documents