ASROCK 990FX Extreme4 Manuel utilisateur

1

ASRock 990FX Extreme4 Motherboard

English

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documentation

by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identiﬁ ca-

tion or explanation and to the owners’ beneﬁ t, without intent to infringe.

Disclaimer:

Speciﬁ cations and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commit-

ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may

appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or ﬁ tness for a particular purpose. In no event shall ASRock, its

directors, ofﬁ cers, employees, or agents be liable for any indirect, special, incidental, or

consequential damages (including damages for loss of proﬁ ts, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the pos-

sibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published July 2013

Copyright

©

2

ASRock 990FX Extreme4 Motherboard

English

Motherboard Layout

24.4cm (9.6-in)

SOCKET AM3b

AMD

990FX

Chipset

DDR3_A1 (64 bit, 240-pin module)

DDR3_A2 (64 bit, 240-pin module)

DDR3_B1 (64 bit, 240-pin module)

DDR3_B2 (64 bit, 240-pin module)

ATX1 2V1

CPU_FAN2

CPU_FAN1

CHA_FAN2

CHA_FAN3

CLRCMOS1

1

USB8_9

1

USB2_3

1

FRONT_1394

1

IDE1

SATA3_5_6

SATA3_3_4

SATA3_1_2

1

PLED1

SPEAKER1

1

Dr.

Debug

PWRBTN1

RSTBTN1

USB3_0_1

HDLED RESET

PLED PWRBTN

1

PANEL 1

FLOPPY1

COM1

1

SATA3_7

SATA3_8

PCIE5

PCI2

PCIE4

PCIE1

PCIE2

PCIE3

PCI1

PWR_FAN1

CD1

HD_AUDIO1

1

CHA_FAN1

IR1

CMOS

BATTERY

LAN

PHY

PS2

Keyboard

Coaxial

SPDIF

Optical

SPDIF

Clr

CMOS

PS2

Mouse

USB 2.0

T: U SB0

B: USB1

RJ-45 LAN

USB 2.0

T: US B6

B: USB7

USB 2.0

T: US B4

B: USB5

eSATA3

IEEE 1394

USB 3.0

T: U SB2

B: USB3

Top:

SIDE SPK

Center:

REAR SPK

Bottom:

CTR BASS

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

AUDIO

CODEC

32Mb

BIOS

Super

I/O

30.5cm (12.0-in)

DDR3 1866

HT3.0

Phenom II

AM3+

FSB2.6GHz

Dual Channel

140W CPU

Designed in Taipei

990FX Extreme4

Support 8-Core CPU

PCI Express 2.0

SATA3 6Gb/s

ErP/EuP Ready

Front USB 3.0

RoHS

1394a

USB 3.0

1

HDMI_SPDIF1

AMD

SB950

Chipset

14

1

2

3

4

5

6

7

8

9

11

12

13

16

15

17

18

19

20

21

22

23

24242525262627282930313233

34

35

36

37

38

39

40

41

42

43

44

10

45

1 HDMI_SPDIF Header (HDMI_SPDIF1, White) 23 Chassis Speaker Header

2 Chassis Fan Connector (CHA_FAN3) (SPEAKER 1, White)

3 Clear CMOS Jumper (CLRCMOS1) 24 Dr. Debug (LED)

4 Chassis Fan Connector (CHA_FAN2) 25 Reset Switch (RSTBTN)

5 ATX 12V Power Connector (ATX12V1) 26 Power Switch (PWRBTN)

6 CPU Fan Connector (CPU_FAN1) 27 SPI Flash Memory (32Mb)

7 CPU Fan Connector (CPU_FAN2) 28 USB 3.0 Header (USB3_0_1, Light Blue)

8 CPU Heatsink Retention Module 29 System Panel Header (PANEL1, White)

9 AM3+ CPU Socket 30 Floppy Connector (FLOPPY1)

10 2 x 240-pin DDR3 DIMM Slots 31 Serial Port Connector (COM1)

(Dual Channel B: DDR3_A1, DDR3_B1; Blue) 32 SATA3 Connector (SATA3_7, White)

11 2 x 240-pin DDR3 DIMM Slots 33 SATA3 Connector (SATA3_8, White)

(Dual Channel B: DDR3_A2, DDR3_B2; White) 34 PCI Express 2.0 x16 Slot (PCIE5; Blue)

12 ATX Power Connector (ATXPWR1) 35 PCI Slot (PCI2)

13 USB 2.0 Header (USB8_9, Blue) 36 PCI Express 2.0 x16 Slot (PCIE4; Blue)

14 USB 2.0 Header (USB2_3, Blue) 37 PCI Slot (PCI1)

15 Front Panel IEEE 1394 Header 38 PCI Express 2.0 x1 Slot (PCIE3; White)

(FRONT_1394, White) 39 PCI Express 2.0 x16 Slot (PCIE2; Blue)

16 Northbridge Controller 40 Power Fan Connector (PWR_FAN1)

17 Southbridge Controller 41 PCI Express 2.0 x1 Slot (PCIE1; White)

18 Primary IDE Connector (IDE1, Blue) 42 Internal Audio Connector: CD1 (White)

19 SATA3 Connector (SATA3_5_6, White) 43 Front Panel Audio Header

20 SATA3 Connector (SATA3_3_4, White) (HD_AUDIO1, White)

21 SATA3 Connector (SATA3_1_2, White) 44 Infrared Module Header (IR1)

22 Power LED Header (PLED1) 45 Chassis Fan Connector (CHA_FAN1)

3

ASRock 990FX Extreme4 Motherboard

English

I/O Panel

**

If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 9) (No. 6) (No. 7) (No. 5)

2 V -- -- --

4 V V -- --

6 V V V --

8 V V V V

LAN Port

ACT/LINK

LED

SPEED

LED

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No Link Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

1

2

4

3

5

6

7

8

9

10

11

12

13

14

15

16

17

18

1 PS/2 Mouse Port (Green) 10 Microphone (Pink)

2 Coaxial SPDIF Out Port 11 USB 3.0 Ports (USB23)

*3 LAN RJ-45 Port 12 IEEE 1394 Port (IEEE 1394)

4 USB 2.0 Ports (USB45) ***13 eSATA3 Connector

5 Side Speaker (Gray) 14 USB 2.0 Ports (USB67)

6 Rear Speaker (Black) 15 USB 2.0 Ports (USB01)

7 Central / Bass (Orange) 16 Optical SPDIF Out Port

8 Line In (Light Blue) 17 Clear CMOS Switch (CLRCBTN)

**9 Front Speaker (Lime) 18 PS/2 Keyboard Port (Purple)

4

ASRock 990FX Extreme4 Motherboard

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will ﬁ nd “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”.

Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Pri-

mary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA

Audio 2nd output” to use front panel audio.

*** eSATA3 connector supports SATA Gen3 in cable 1M.

English

5

ASRock 990FX Extreme4 Motherboard

1. Introduction

Thank you for purchasing ASRock 990FX Extreme4 motherboard, a reliable moth-

erboard produced under ASRock’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock’s commitment to

quality and endurance.

In this manual, chapter 1 and 2 contain introduction of the motherboard and step-

by-step guide to the hardware installation. Chapter 3 and 4 contain the conﬁ guration

guide to BIOS setup and information of the Support CD.

Because the motherboard speciﬁ cations and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modiﬁ cations of this manual occur, the updated ver-

sion will be available on ASRock website without further notice. You may

ﬁ nd the latest VGA cards and CPU support lists on ASRock website as

well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for speciﬁ c information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock 990FX Extreme4 Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

ASRock 990FX Extreme4 Quick Installation Guide

ASRock 990FX Extreme4 Support CD

1 x ASRock SLI_Bridge_2S Card

1 x 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

1 x Ribbon Cable for a 3.5-in Floppy Drive

4 x Serial ATA (SATA) Data Cables (Optional)

2 x Serial ATA (SATA) HDD Power Cables (Optional)

1 x 3.5mm Audio Cable (Optional)

1 x I/O Panel Shield

1 x Front USB 3.0 Panel

4 x HDD Screws

6 x Chassis Screws

1 x Rear USB 3.0 Bracket

ASRock Reminds You...

To get better performance in Windows

®

7 / 7 64-bit / Vista

TM

/ Vista

TM

64

bit, it is recommended to set the BIOS option in Storage Conﬁ guration

to AHCI mode. For the BIOS setup, please refer to the “User Manual” in

our support CD for details.

English

6

ASRock 990FX Extreme4 Motherboard

1.2 Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

- All Solid Capacitor design (100% Japan-made high-quality

Conductive Polymer Capacitors)

CPU - Support for Socket AM3+ processors

- Support for Socket AM3 processors: AMD Phenom

TM

II X6 /

X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 /

Sempron processors

- Supports 8-Core CPU

- Supports UCC feature (Unlock CPU Core) (see CAUTION 1)

- Advanced V8 + 2 Power Phase Design

- Supports CPU up to 140W

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

- FSB 2600 MHz (5.2 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - Northbridge: AMD 990FX

- Southbridge: AMD SB950

Memory - Dual Channel DDR3 Memory Technology (see CAUTION 3)

- 4 x DDR3 DIMM slots

- Support DDR3 2100(OC)/1866/1600/1333/1066/800

non-ECC, un-buffered memory (see CAUTION 4)

- Max. capacity of system memory: 32GB (see CAUTION 5)

Expansion Slot - 3 x PCI Express 2.0 x16 slots (PCIE2/PCIE4: x16 mode;

PCIE5: x4 mode)

- 2 x PCI Express 2.0 x1 slots

- 2 x PCI slots

- Supports AMD

TM

Quad CrossFireX

TM

, 3-Way CrossFireX

TM

and CrossFireX

TM

- Supports NVIDIA

®

Quad SLI

TM

and SLI

TM

Audio - 7.1 CH HD Audio with Content Protection

(Realtek ALC892 Audio Codec)

- Premium Blu-ray audio support

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Broadcom BCM57781

- Supports Wake-On-LAN

- Supports Energy Efﬁ cient Ethernet 802.3az

- Supports PXE

Rear Panel I/O I/O Panel

English

7

ASRock 990FX Extreme4 Motherboard

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 6 x Ready-to-Use USB 2.0 Ports

- 2 x Ready-to-Use USB 3.0 Ports

- 1 x eSATA3 Connector

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

- 1 x IEEE 1394 Port

- 1 x Clear CMOS Switch with LED

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 6)

SATA3 - 6 x SATA3 6.0 Gb/s connectors by AMD SB950, support

RAID (RAID 0, RAID 1, RAID 0+1, JBOD and RAID 5), NCQ,

AHCI and "Hot Plug" functions

- 2 x SATA3 6.0 Gb/s connectors by Marvell SE9120, support

NCQ, AHCI and “Hot Plug” functions

(SATA3_8 connector is shared with eSATA3 port)

USB 3.0 - 2 x Rear USB 3.0 ports by Etron EJ168A, support USB 1.0

/2.0/3.0 up to 5Gb/s

- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports) by

Etron EJ168A, supports USB 1.0/2.0/3.0 up to 5Gb/s

Connector - 8 x SATA3 6.0Gb/s connectors

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x COM port header

- 1 x IEEE 1394 header

- 1 x HDMI_SPDIF header

- 1 x Power LED header

- CPU/Chassis/Power FAN connector

- 24 pin ATX power connector

- 8 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

- 1 x USB 3.0 header (supports 2 USB 3.0 ports)

- 1 x Dr. Debug (7-Segment Debug LED)

Smart Switch - 1 x Clear CMOS Switch with LED

- 1 x Power Switch with LED

English

8

ASRock 990FX Extreme4 Motherboard

English

- 1 x Reset Switch with LED

BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- CPU, VCCM, NB, SB Voltage Multi-adjustment

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version),

CyberLink MediaEspresso 6.5 Trial

Unique Feature - ASRock Extreme Tuning Utility (AXTU) (see CAUTION 7)

- ASRock Instant Boot

- ASRock Instant Flash (see CAUTION 8)

- ASRock APP Charger (see CAUTION 9)

- ASRock XFast USB (see CAUTION 10)

- ASRock On/Off Play Technology (see CAUTION 11)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 12)

- ASRock U-COP (see CAUTION 13)

- Boot Failure Guard (B.F.G.)

- Turbo 50 / Turbo 60 CPU Overclocking

- Turbo UCC

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU Quiet Fan

- CPU/Chassis Fan Multi-Speed Control

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

7 / 7 64-bit / Vista

TM

/ Vista

TM

64-bit / XP

/ XP 64-bit compliant

Certiﬁ cations - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required)

(see CAUTION 14)

* For detailed product information, please visit our website: http://www.asrock.com

9

ASRock 990FX Extreme4 Motherboard

CAUTION!

1. ASRock UCC (Unlock CPU Core) feature simpliﬁ es AMD CPU activa-

tion. As long as a simple switch of the UEFI option “ASRock UCC”, you

can unlock the extra CPU core to enjoy an instant performance boost.

When UCC feature is enabled, the dual-core or triple-core CPU will boost

to the quad-core CPU, and some CPU, including quad-core CPU, can

also increase L3 cache size up to 6MB, which means you can enjoy the

upgrade CPU performance with a better price. Please be noted that UCC

feature is supported with AM3 CPU only, and in addition, not every AM3

CPU can support this function because some CPU’s hidden core may be

malfunctioned.

2. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 39 for details.

3. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 14 for proper installation.

4. Whether 2100MHz memory speed is supported depends on the AM3/

AM3+ CPU you adopt. If you want to adopt DDR3 2100 memory module

on this motherboard, please refer to the memory support list on our web-

site for the compatible memory modules.

ASRock website http://www.asrock.com

5. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

7 /

Vista

TM

/ XP. For Windows

®

64-bit OS with 64-bit CPU, there is no such

limitation.

6. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-chan-

nel, 6-channel, and 8-channel modes. Please check the table on page 3

for proper connection.

7. ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to ne-tune

different system functions in a user-friendly interface, which is including

Hardware Monitor, Fan Control, Overclocking, OC DNA and IES. In Hard-

ware Monitor, it shows the major readings of your system. In Fan Control,

it shows the fan speed and temperature for you to adjust. In Overclock-

ing, you are allowed to overclock CPU frequency for optimal system per-

formance. In OC DNA, you can save your OC settings as a proﬁ le and

share with your friends. Your friends then can load the OC proﬁ le to

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the

setting in the BIOS, applying Untied Overclocking Technology, or using the third-party over-

clocking tools. Overclocking may affect your system stability, or even cause damage to the

components and devices of your system. It should be done at your own risk and expense.

We are not responsible for possible damage caused by overclocking.

English

10

ASRock 990FX Extreme4 Motherboard

English

their own system to get the same OC settings. In IES (Intelligent Energy

Saver), the voltage regulator can reduce the number of output phases to

improve efﬁ ciency when the CPU cores are idle without sacriﬁ cing com-

puting performance. Please visit our website for the operation procedures

of ASRock Extreme Tuning Utility (AXTU).

ASRock website: http://www.asrock.com

8. ASRock Instant Flash is a BIOS ﬂ ash utility embedded in Flash ROM.

This convenient BIOS update tool allows you to update system BIOS

without entering operating systems ﬁ rst like MS-DOS or Windows

®

. With

this utility, you can press <F6> key during the POST or press <F2> key to

BIOS setup menu to access ASRock Instant Flash. Just launch this tool

and save the new BIOS ﬁ le to your USB ﬂ ash drive, ﬂ oppy disk or hard

drive, then you can update your BIOS only in a few clicks without prepar-

ing an additional ﬂ oppy diskette or other complicated ﬂ ash utility. Please

be noted that the USB ﬂ ash drive or hard drive must use FAT32/16/12 ﬁ le

system.

9. If you desire a faster, less restricted way of charging your Apple devices,

such as iPhone/iPod/iPad Touch, ASRock has prepared a wonderful so-

lution for you - ASRock APP Charger. Simply installing the APP Charger

driver, it makes your iPhone charged much quickly from your computer

and up to 40% faster than before. ASRock APP Charger allows you to

quickly charge many Apple devices simultaneously and even supports

continuous charging when your PC enters into Standby mode (S1), Sus-

pend to RAM (S3), hibernation mode (S4) or power off (S5). With APP

Charger driver installed, you can easily enjoy the marvelous charging

experience than ever.

ASRock website: http://www.asrock.com/Feature/AppCharger/index.asp

10. ASRock XFast USB can boost USB storage device performance. The

performance may depend on the property of the device.

11. ASRock On/Off Play Technology allows users to enjoy the great audio ex-

perience from the portable audio devices, such like MP3 player or mobile

phone to your PC, even when the PC is turned off (or in ACPI S5 mode)!

This motherboard also provides a free 3.5mm audio cable (optional) that

ensures users the most convenient computing environment.

12. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

13. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug

it back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC sys-

tem.

11

ASRock 990FX Extreme4 Motherboard

English

14. EuP, stands for Energy Using Product, was a provision regulated by Eu-

ropean Union to deﬁ ne the power consumption for the completed system.

According to EuP, the total AC power of the completed system shall be

under 1.00W in off mode condition. To meet EuP standard, an EuP ready

motherboard and an EuP ready power supply are required. According to

Intel’s suggestion, the EuP ready power supply must meet the standard

of 5v standby power efﬁ ciency is higher than 50% under 100 mA current

consumption. For EuP ready power supply selection, we recommend you

checking with the power supply manufacturer for more details.

12

ASRock 990FX Extreme4 Motherboard

2. Installation

This is an ATX form factor (12.0-in x 9.6-in, 30.5 cm x 24.4 cm) motherboard.

Before you install the motherboard, study the conﬁ guration of your chassis to ensure

that the motherboard ﬁ ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static elec-

tricity, NEVER place your motherboard directly on the carpet or the

like. Also remember to use a grounded wrist strap or touch a safety

grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the mother-

board to the chassis, please do not over-tighten the screws! Doing

so may damage the motherboard.

English

13

ASRock 990FX Extreme4 Motherboard

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90

o

angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it ﬁ ts in place.

The CPU ﬁ ts only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it ﬁ rmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a

larger heatsink and cooling fan to dissipate heat. You also need to spray

thermal grease between the CPU and the heatsink to improve heat dis-

sipation. Make sure that the CPU and the heatsink are securely fastened

and in good contact with each other. Then connect the CPU fan to the

CPU FAN connector (CPU_FAN1, see Page 2, No. 6 or CPU_FAN2, see

Page 2, No. 7). For proper installation, please kindly refer to the instruc-

tion manuals of the CPU fan and the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:

Match The CPU Golden Triangle

To The Socket Corner Small

Triangle

STEP 4:

Push Down And Lock

The Socket Lever

Lever 90° Up

CPU Golden Triangle

Socker Corner

Small Triangle

English

14

ASRock 990FX Extreme4 Motherboard

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel conﬁ guration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR3 DIMM pair in the slots of the same color. In other words, you have to install

identical DDR3 DIMM pair in Dual Channel A (DDR3_A1 and DDR3_B1; Blue

slots; see p.2 No.10) or identical DDR3 DIMM pair in Dual Channel B (DDR3_

A2 and DDR3_B2; White slots; see p.2 No.11), so that Dual Channel Memory

Technology can be activated. This motherboard also allows you to install four DDR3

DIMMs for dual channel conﬁ guration, and please install identical DDR3 DIMMs in

all four slots. You may refer to the Dual Channel Memory Conﬁ guration Table below.

Dual Channel Memory Conﬁ gurations

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

(Blue Slot) (White Slot) (Blue Slot) (White Slot)

(1) Populated - Populated -

(2) - Populated - Populated

(3)* Populated Populated Populated Populated

*

For the conﬁ guration (3), please install identical DDR3 DIMMs in all four

slots.

1. Please install the memory module into the white slot (DDR3_A2

and DDR3_B2) for the ﬁ rst priority.

2. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue

slots (DDR3_A1 and DDR3_B1), or in the set of white slots (DDR3_

A2 and DDR3_B2).

3. If only one memory module or three memory modules are installed

in the DDR3 DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

4. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel

Memory Technology .

5. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot; otherwise, this motherboard and DIMM may be dam-

aged.

6. If you adopt DDR3 2100 memory modules on this motherboard, it is

recommended to install them on DDR3_A2 and DDR3_B2 slots.

English

15

ASRock 990FX Extreme4 Motherboard

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only ﬁ ts in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

English

16

ASRock 990FX Extreme4 Motherboard

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 5 PCI Express slots on this motherboard.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots:

PCIE1 / PCIE3 (PCIE x1 slot; White) is used for PCI Express cards with

x1 lane width cards, such as Gigabit LAN card and SATA2 card.

PCIE2 / PCIE4 (PCIE x16 slot; Blue) is used for PCI Express x16 lane

width graphics cards, or used to install PCI Express graphics cards to

support SLI

TM

and CrossFireX

TM

function.

PCIE5 (PCIE x16 slot; Blue) is used for PCI Express x4 lane width

cards, or used to install PCI Express graphics cards to support 3-Way

CrossFireX

TM

function.

1. In single VGA card mode, it is recommended to install a PCI Ex-

press x16 graphics card on PCIE2 slot.

2. In CrossFireX

TM

or SLI

TM

mode, please install PCI Express x16

graphics cards on PCIE2 and PCIE4 slots. Therefore, both these

two slots will work at x16 bandwidth.

3. In 3-Way CrossFireX

TM

mode, please install PCI Express x16 graph-

ics cards on PCIE2, PCIE4 and PCIE5 slots. Therefore, PCIE2 and

PCIE4 slots will work at x16 bandwidth while PCIE5 slot will work at

x4 bandwidth.

4. Please connect a chassis fan to motherboard chassis fan connec-

tor (CHA_FAN1, CHA_FAN2 or CHA_FAN3) when using multiple

graphics cards for better thermal environment.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press ﬁ rmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

English

17

ASRock 990FX Extreme4 Motherboard

2.5 SLI

TM

and Quad SLI

TM

Operation Guide

This motherboard supports NVIDIA

®

SLI

TM

and Quad SLI

TM

(Scalable Link Interface)

technology that allows you to install up to three identical PCI Express x16 graphics

cards. Currently,

NVIDIA

®

SLI

TM

technology supports Windows

®

XP / XP 64-bit /

Vista

TM

/ Vista

TM

64-bit / 7 / 7 64-bit OS. NVIDIA

®

Quad SLI

TM

technology support

Windows

®

Vista

TM

/ Vista

TM

64-bit / 7 / 7 64-bit OS only. Please follow the installation

procedures in this section.

Requirements

1. For SLI

TM

technology, you should have two identical SLI

TM

-ready

graphics cards that are NVIDIA

®

certiﬁ ed. For Quad SLI

TM

technolo-

gy, you should have two identical Quad SLI

TM

-ready graphics cards

that are NVIDIA

®

certiﬁ ed.

2. Make sure that your graphics card driver supports NVIDIA

®

SLI

TM

technology. Download the driver from NVIDIA

®

website

(www.nvidia.com).

3. Make sure that your power supply unit (PSU) can provide at least

the minimum power required by your system. It is recommended

to use NVIDIA

®

certiﬁ ed PSU. Please refer to NVIDIA

®

website for

details.

2.5.1 Graphics Card Setup

2.5.1.1 Installing Two SLI

TM

-Ready Graphics Cards

Step 1. Install the identical SLI

TM

-ready graphics cards that are NVIDIA

®

certiﬁ ed

because different types of graphics cards will not work together properly.

(Even the GPU chips version shall be the same.) Insert one graphics card

into PCIE2 slot and the other graphics card to PCIE4 slot. Make sure that

the cards are properly seated on the slots.

Step2. If required, connect the auxiliary power source to the PCI Express

graphics cards.

English

18

ASRock 990FX Extreme4 Motherboard

Step3. Align and insert ASRock SLI_Bridge_2S Card to the goldﬁ ngers on each

graphics card. Make sure ASRock SLI_Bridge_2S Card is ﬁ rmly in place.

ASRock SLI_Bridge_2S Card

Step4. Connect a VGA cable or a DVI cable to the monitor connector or the DVI

connector of the graphics card that is inserted to PCIE2 slot.

2.5.2 Driver Installation and Setup

Install the graphics card drivers to your system. After that, you can enable the Multi-

Graphics Processing Unit (GPU) feature in the NVIDIA

®

nView system tray utility.

Please follow the below procedures to enable the multi-GPU feature.

For Windows

®

XP / XP 64-bit OS:

(For SLI

TM

mode only)

A. Double-click NVIDIA Settings icon on your Windows

®

taskbar.

C. Reboot your system.

D. You can freely enjoy the beneﬁ t of SLI

TM

feature.

B. From the pop-up menu, select Set SLI and PhysX conﬁ guration. In

Set PhysX GPU acceleration item, please select Enabled. In Select

an SLI conﬁ guration item, please select Enable SLI. And click Apply.

English

19

ASRock 990FX Extreme4 Motherboard

For Windows

®

Vista

TM

/ Vista

TM

64-bit / 7 / 7 64-bit OS:

(For SLI

TM

and Quad SLI

TM

mode)

A. Click the Start icon on your Windows taskbar.

B. From the pop-up menu, select All Programs, and then click NVIDIA

Corporation.

C. Select NVIDIA Control Panel tab.

D. Select Control Panel tab.

F. Reboot your system.

G.You can freely enjoy the beneﬁ t of SLI

TM

or Quad SLI

TM

feature.

* SLI

TM

appearing here is a registered trademark of NVIDIA

®

Technologies Inc., and is used

only for identiﬁ cation or explanation and to the owners’ beneﬁ t, without intent to infringe.

E. From the pop-up menu, select Set SLI and PhysX conﬁ guration. In

Set PhysX GPU acceleration item, please select Enabled. In Select

an SLI conﬁ guration item, please select Enable SLI. And click Apply.

English

20

ASRock 990FX Extreme4 Motherboard

2.6 CrossFireX

TM

, 3-Way CrossFireX

TM

and Quad CrossFireX

TM

Operation Guide

This motherboard supports CrossFireX

TM

, 3-way CrossFireX

TM

and Quad

CrossFireX

TM

feature. CrossFireX

TM

technology offers the most advantageous

means available of combining multiple high performance Graphics Processing

Units (GPU) in a single PC. Combining a range of different operating modes with

intelligent software design and an innovative interconnect mechanism, CrossFireX

TM

enables the highest possible level of performance and image quality in any 3D

application. Currently CrossFireX

TM

feature is supported with Windows

®

XP with

Service Pack 2 / Vista

TM

/ 7 OS. 3-way CrossFireX

TM

and Quad CrossFireX

TM

feature

are supported with Windows

®

Vista

TM

/ 7 OS only. Please check AMD website for

AMD

TM

CrossFireX

TM

driver updates.

2.6.1 Graphics Card Setup

2.6.1.1 Installing Two CrossFireX

TM

-Ready Graphics

Cards

Different CrossFireX

TM

cards may require different methods to enable CrossFi-

reX

TM

feature. In below procedures, we use Radeon HD 3870 as the example

graphics card. For other CrossFireX

TM

cards that AMD

TM

has released or will

release in the future, please refer to AMD

TM

graphics card manuals for detailed

installation guide.

Step 1. Insert one Radeon graphics card into PCIE2 slot and the other Radeon

graphics card to PCIE4 slot. Make sure that the cards are properly seated

on the slots.

1. If a customer incorrectly configures their system they will not see the

performance beneﬁ ts of CrossFireX

TM

. All three CrossFireX

TM

components, a

CrossFireX

TM

Ready graphics card, a CrossFireX

TM

Ready motherboard and a

CrossFireX

TM

Edition co-processor graphics card, must be installed correctly

to beneﬁ t from the CrossFireX

TM

multi-GPU platform.

2. If you pair a 12-pipe CrossFireX

TM

Edition card with a 16-pipe card, both cards

will operate as 12-pipe cards while in CrossFireX

TM

mode.

English

La page charge ...

ASROCK 990FX Extreme4 Manuel utilisateur

ASROCK 990FX Extreme4 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents