NEC FE2111SB - MultiSync - 22" CRT Display Manuel utilisateur

Index

Warning.................................................................................................. 1

Contents ............................................................................................... 2

Quick Start ...........................................................................................3

Controls ................................................................................................ 5

Recommended Use ............................................................................. 9

Specifications .....................................................................................12

Features .............................................................................................. 13

Troubleshooting ................................................................................. 15

References .......................................................................................... 17

Limited Warranty ..............................................................................18

TCO’95 .................................................................................................. 19

TCO’99 ..................................................................................................21

Avertissement ................................................................................... 25

Contenu .............................................................................................. 26

Mise en marche rapide .................................................................... 27

Commandes ....................................................................................... 29

Usage recommandé ...........................................................................33

Fiche technique ................................................................................ 36

Fonctions .............................................................................................37

Dépannage ......................................................................................... 38

Références ......................................................................................... 40

Garantie limitée .................................................................................41

TCO’95 ................................................................................................. 42

TCO’99 ................................................................................................. 44

Warnung ............................................................................................. 48

Lieferumfang..................................................................................... 50

Quick Start ......................................................................................... 51

Bedienungselemente ....................................................................... 53

Empfehlungen für die Verwendung .............................................. 57

Technische Daten ............................................................................. 60

Funktionen .......................................................................................... 61

Fehlerbehebung ................................................................................ 62

Verweise ............................................................................................. 64

Beschränkte Gewährleistung......................................................... 65

TCO’95 ................................................................................................. 66

TCO’99 ................................................................................................. 68

1

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-

Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to

C.S.A. 22.2 #950.

FCC Information

1.

Use the attached specified cables with the C22BW7

01

color monitor so as not to interfere with radio and

television reception.

(1) Please use the supplied power cable or equivalent to ensure FCC compliance.

(2) Shielded signal cable.

Use of other cables and adapters may cause interference with radio and television reception.

2.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

• No user serviceable parts inside. Do not attempt to modify this equipment. If modified, your

authority to operate this equipment might be voided by FCC.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional

suggestions. The user may find the following booklet, prepared by the Federal Communications Commis-

sion, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from

the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

No user serviceable parts inside. Do not attempt to modify this equipment. If modified, your authority to

operate this equipment might be voided by FCC.

VCCI Statement

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE

THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS

CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This

symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this

unit has been included. Therefore, it should be read carefully in order to avoid any problems.

2

Your new NEC MultiSync

®

FE2111SB monitor box* should contain

the following:

• MultiSync FE2111SB with tilt/swivel base

• Power Cord

• Signal Cable

(D-Sub to D-Sub)

• User’s Manual

Contents

Power Cord

User’s Manual

* Remember to save your original box and packing material to transport or ship the monitor.

Signal Cable

3

Quick Start

To attach the FE monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. If necessary, install the graphics card into your system. For more information,

refer to the graphics card installation manual.

3.

For the PC: Connect the 15-pin mini D-SUB connector of the signal cable to the

connector of the display card in your system (Figure A.1). Tighten all screws.

For the Mac: Connect the MultiSync Macintosh cable adapter (not included) to

the monitor connector on the Macintosh (Figure B.1). Attach the 15-pin mini

D-SUB end of the signal cable to the MultiSync Macintosh cable adapter on

the computer (Figure B.1). Tighten all screws.

NOTE: To obtain the MultiSync Macintosh cable adapter, call NEC-Mitsubishi

Electronics Display of America, Inc. at (800) 632-4662.

4. Connect the other end of the signal cable to the connector on the back of the

MultiSync monitor.

5. Connect one end of the power cord to the MultiSync monitor and the other

end to the power outlet (Figure C.1).

6. Turn on the monitor (Figure D.1) and the computer.

NOTE: For download information on the Windows

®

98/2000/Me/XP INF file for your

MultiSync monitor, refer to the References section of this User’s Manual.

NOTE: If you have any problems, please refer to the Troubleshooting section of

this User’s Manual.

Figure B.1

Figure A.1

15-pin

mini

D-SUB

Capative Signal Cable

Mac Adapter

(Not Included)

Capative Signal Cable

4

Quick Start –continued

Figure D.1

Power

Cord

Figure C.1

5

OSM

™

(On-Screen Manager) control buttons on the front of the monitor function

as follows:

Main Menu Sub-Menu

EXIT Exits the OSM menu. Exits to the OSM controls

main menu.

Note :

Deactivates the OSM menu and activates the OSM menu when the OSM is turned off.

CONTROL Moves the highlighted Moves the highlighted area

area left/right to select left/right to select one of the

one of the sub-menu. controls.

Note : When the OSM menu is off, it acts as a Hot key for Brightness.

CONTROL Has no function Moves the bar in the – or +

-/+ direction to decrease or

increase the adjustment.

Note : Deactivates the OSM menu and to adjust Contrast with Hot key set “ON”

SELECT/ Enters sub-menu. Has no function.

SB MODE

When the OSM is off, it will act as the SuperBright (SB) function key. User can

select between SB MODE OFF, SB MODE1, and SB MODE2. The first time this

key is pressed, the current SB Mode is indicated. Within a 3 second window, if

this key is selected again, the SB MODE will change to the next SB MODE. For

example, the current mode is SB MODE OFF, the key is pressed twice within a 3

second time frame, the SB MODE will change to SB MODE1 and so on. The

color temperature at each SB Mode is adjusted by appropriate color control

except for the sRGB mode whose color setting cannot be adjusted. When the unit

is turned off, it will reset to SB off mode.

RESET Resets all the controls within the Resets the highlighted control to

highlighted menu to the factory the factory setting.

setting.

Note: When RESET is pressed in the main and sub-menu, a warning window will

appear allowing you to select the reset function.

Brightness/Contrast Controls

Brightness: Adjusts the overall image and background screen brightness.

Contrast: Adjusts the image brightness in relation to the background.

Degauss: Eliminates the buildup of stray magnetic fields which alter the correct scan of the

electron beams and affect the purity of the screen colors, focus and convergence. When

activated, your screen image will jump and waver a bit as the screen is demagnetized.

NOTE:

Please allow a minimum of 20 minutes to elapse between uses of the Degauss Control.

Constant Brightness: sustains the brightness and screen color levels consistently over the

normal life of the monitor. The Constant Brightness function requires a 30 minute warm-

up of the monitor before the feature is fully functional.

Controls

6

Size and Position Controls

Auto Adjust: Automatically adjust the horizontal and vertical size and position settings for

the applicable timing signal.

NOTE: Auto Adjust is unavailable with no image signal or narrow size of image signal input.

Left/Right: Moves the image horizontally (left or right).

Down/Up: Moves the image vertically (up or down).

Narrow/Wide: Decreases or increases the horizontal size of the image.

Short/Tall: Decreases or increases the vertical size of the image.

Color Control/AccuColor

®

Control System

Color presets 1 through 5 selects the desired color setting. The bar is replaced by the

color setting choice from 1, 2, 3, sRGB, 5. Each color setting is adjusted at the factory to

the stated Kelvin degrees. If a setting is adjusted, the name of the setting will change from

Kelvin to Custom. NOTE: sRGB does not allow you to adjust each color.

Red, Green, Blue: NEC’s AccuColor Control System decreases or increases the monitor’s

red, green or blue color guns depending upon which is selected. The change in color will

appear on screen and the direction (decrease or increase) will be shown by the bars.

NOTE: sRGB does not allow you to control the AccuColor, Brightness and Contrast.

Geometry Controls

Geometry Controls Menu

The Geometry controls allow you to adjust the curvature or angle of the sides of your display.

In/Out (pincushion): Decreases or increases the curvature of the sides either inward or outward.

Left/Right (pincushion balance): Decreases or increases the curvature of the sides either to

the left or right.

Tilt (parallelogram): Decreases or increases the tilt of the sides either to the left or right.

Align (trapezoidal): Decreases or increases the bottom of the screen to be the same as the top

.

Rotat

e (raster rotation): Rotates the entire display clockwise or counterclockwise.

Corner Correction: Allows you to adjust the geometry of the corners of your display

—

Top, Top Balance, Bottom or Bottom Balance.

Tools 1

Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen. The

pattern is repetitive and superimposed as rippled images. When running certain applications,

the wavy pattern is more evident than in others. To reduce moiré, adjust the level by using the

–/+ CONTROL buttons.

Convergence: Aligns all three colors (R,G,B) to form a single color (white). The purpose of

this control is to ensure that a white line drawn on the screen is as crisp and clear as

possible

.

•

Use the CONVERGENCE (HOR.) control to adjust the alignment of the white lines in the left/right direction.

•

Use the CONVERGENCE (VER.)

control to adjust the alignment of the white lines in the up/down

direction.

Controls –continued

7

Linearity: This selection allows you to adjust the spacing of the area on the screen. The

purpose of this control is to ensure that a one-inch circle is a true one-inch circle wherever

it is on the screen. The best way to determine the vertical linearity is as follows:

• Draw equally spaced horizontal lines using a drawing application that has a ruler.

• Use the Vertical Balance control to adjust the lines near the top and bottom of your screen.

• Use the LINEARITY (VER.) control to adjust the spacing between the lines near the center and

top of your screen.

GlobalSync

®

Control: Eliminates picture impurities that may result from the

earth’s magnetic field. While in the sub-menus, use the –/+ control buttons to fine

tune the GlobalSync corrections.

NOTE:NEC recommends that you perform GlobalSync correction while running

a typical application such as a spreadsheet or text document.

Tools 2

Language: OSM controls menus are available in six languages.

OSM Position: You can choose where you would like the OSM controls menu to

appear on your screen. Selecting OSM Position allows you to manually adjust the

OSM controls menu left, right, up or down.

OSM Turn Off: The OSM controls menu will stay on as long as it is in use. In the

OSM Turn Off sub-menu, you can select how long the monitor waits after the last

touch of a button for the OSM controls menu to disappear. The preset choice is in

5 seconds step between 5–120 seconds.

O

SM Lock Out: This control completely locks out access to all OSM controls

functions except Brightness and Contrast. When attempting to activate OSM

controls while in the lock out mode, a screen will appear indicating that OSM

controls are locked out. To activate the OSM Lock Out function, press SELECT, then

press + and hold down simultaneously. To deactivate the OSM Lock Out, press

SELECT, then press + and hold down simultaneously.

IPM

™

System Off Mode:

Enable: The IPM System works normally and

all stages of energy savings are utilized.

Disable: The Off Mode reset

NOTE:

For standard systems and graphics boards, keep the factory setting at ENABLE.

NOTE: Don’t keep the MultiSync monitor on when ‘No Signal’ is applied. This

could cause image burn in on the screen due to the ‘No Signal’

message being displayed.

EdgeLock

™

Control: Operating your monitor at a nonstandard timing may cause

images to appear darker than normal or have color distortion. Use of the

EdgeLock control will adjust images to their normal state.

Hot Key: This selection allows you to use as brightness control and –/+

as contrast control.

Controls -continued

8

Factory Preset: Selecting Factory Preset allows you a reset most OSM

™

control

settings back to the factory settings. A warning statement will appear to confirm

that you do want to reset ALL settings. Individual settings can be reset by high-

lighting the control to be reset and pressing the RESET button.

Information

Display Mode: Indicates the current mode and frequency setting of the monitor.

Monitor Info: Indicates the model and serial numbers of your monitor.

Refresh Notifier: A message will advise you if the refresh rate of the signal being

applied to the monitor by the computer is too low. For further information, please

refer to your display card or system manual.

Controls –continued

9

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTISYNC

®

FE2111SB COLOR MONITORS:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and

opening or removing covers may expose you to dangerous shock hazards or other

risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch danger-

ous voltage points, which can be harmful or fatal or may cause electric shock, fire

or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may

cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the

monitor may fall, causing serious damage to the monitor.

• Keep the monitor away from high capacity transformers, electric motors and other

devices such as external speakers or fans, which may create strong magnetic

fields.

• Changing the direction of the monitor while it is powered on may cause image

discoloration. To correct this, turn the monitor off for 20 minutes before powering

it back on.

• When operating the MultiSync FE2111SB with its AC 100-120/220-240V

worldwide power supply, use a power supply cord that matches the power supply

voltage of the AC power outlet being used. The power supply cord you use must

have been approved by and comply with the safety standards of your country.

(Type H05VV-F 3G 0.7mm

2

should be used in Europe)

• In UK, use a BS-approved power cord with molded plug having a black (5A) fuse

installed for use with this monitor. If a power cord is not supplied with this monitor,

please contact your supplier.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified

service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• Allow adequate ventilation around the monitor so that heat can properly

dissipate. Do not block ventilated openings or place the monitor near a

radiator or other heat sources. Do not put anything on top of monitor.

• The power cable connector is the primary means of detaching the system

from the power supply. The monitor should be installed close to a power

outlet which is easily accessible.

• Handle with care when transporting. Save packaging for transporting.

Recommended Use

CAUTION

10

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

Recommended Use –continued

• Adjust the monitor height so that the top of

the screen is at or slightly below eye level.

Your eyes should look slightly downward

when viewing the middle of the screen.

• Position your monitor no closer than 12 inches

and no further away than 28 inches from your

eyes. The optimal distance is 24 inches.

• Rest your eyes periodically by focusing on

an object at least 20 feet away. Blink often.

• Position the monitor at a 90° angle to

windows and other light sources to minimize

glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect

on your screen.

• If reflected light makes it hard for you to see your screen, use an antiglare filter.

• Clean your monitor

A special coating is provided on the glass (CRT) surface of this monitor to

reduce a reflection and static electricity on the glass surface.

Due to the delicate coating on the glass surface, use a lint-free, nonabrasive

cloth (cotton or equivalent) and a non-alcohol, neutral, nonabrasive cleaning

solution to minimize dust. If the screen requires more than a light cleaning,

apply water or soften neutral detergent with much water directly to a soft cloth

and use it upon wringing water, to clean the glass surface.

CAUTION: The following agents will cause damage to the CRT when cleaning

the glass surface: Benzene, thinner, acid/alkaline detergent, alcohol deter-

gent, detergent with abrasive powder, detergent with antistatic agent, deter-

gent for cleaning.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or

reference material) directly in front of you to minimize turning your head

while you are typing.

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Adjust the Brightness until the background raster disappears

• Do not position the Contrast control to its maximum setting

• Use the preset Size and Position controls with standard signals

11

Recommended Use –continued

• Use the preset Color Setting and Sides Left/Right controls

• Use non-interlaced signals with a vertical refresh rate between 75-160Hz

• Do not use primary color blue on a dark background, as it is difficult to see

and may produce eye fatigue due to insufficient contrast

For more detailed information on setting up a healthy work environment, write the

American National Standard for Human Factors Engineering of Visual Display Terminal

Workstations – ANSI-HFS Standard No. 100-1988 - The Human Factors Society, Inc.

P.O. Box 1369, Santa Monica, California 90406.

12

Specifications

Monitor MultiSync

®

FE2111SB

™

Notes

Specifications Monitor

Picture Tube Diagonal: 22 inch/55 cm 90° deflection, 0.24 mm grille pitch,

Viewable Image Size: 20 inch/508 mm medium short persistence phosphor,

Radius: 50000 mm aperture grille CRT, G-WARAS coating

Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms

Sync: Separate sync. TTL Level

Horizontal sync. Positive/Negative

Vertical sync. Positive/Negative

Composite sync. (Negative) (TTL Level)

Display Colors Analog input: Unlimited number of Colors Depends on display card used.

Synchronization Horizontal: 30 kHz to 115 kHz Automatically

Range Vertical: 50 Hz to 160 Hz Automatically

Resolutions Supported 640 x 480 @ 50 to 160 Hz

Some systems may not support

Resolution based on

horizontal and

800 x 600 @ 50 to 160 Hz

all modes listed.

vertical frequencies only

1024 x 768 @ 50 to 138 Hz

1280 x 1024 @ 50 to 105 Hz

1600 x 1200 @ 50 to 91 Hz

...................... NEC-Mitsubishi Electronics Display cites

1800 x 1350 @ 50 to 81 Hz

recommended resolution a 85 Hz for

1800 x 1440 @ 50 to 76 Hz

optimal display performance.

1856 x 1392 @ 50 to 79 Hz

1920 x 1440 @ 50 to 76 Hz

Active Display Area Horizontal:

396 mm/15.6 inches Dependent upon signal timing used,

(Factory Setting) Vertical:

297 mm/11.7 inches and does not

include border area.

Active Display Area

406 mm/16.0 inches Dependent upon signal timing used,

(Full Scan)

304.6 mm/12.0 inches and does not

include border area.

Power Supply

AC 100 – 120 V/220 - 240 V, 50/60 Hz

Current Rating 1.25A @ 100

–

120 V / 0.6A @ 220-240 V

Dimensions

495 mm (W) x 484.5 mm (H) x 471 mm (D)

19.5 inches (W) x 19.1 inches (H) x 18.5 inches (D)

Weight 29.0 kg

64.0 lbs

Environmental Considerations

Operating Temperature: +5°C to +35°C/+41°F to +90°F

Humidity: 10% to 90%

Altitude: 0 ft (0 m) ~ 10,000 ft (3,000 m)

Storage Temperature: -20°C to +60°C/-4°F to +140°F

Humidity: 10% to 90%

Altitude: 0 ft (0 m) ~ 50,000 ft (15,000 m)

NOTE: Technical specifications are subject to change without notice.

13

Features

Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a

virtually

flat image, eliminating distortion and reducing glare so that what you see

on-screen is what you get on your printed output. The striped phosphor alignment

of the CRT delivers superior vertical definition with improved brightness for more

uniform image contrast.

OptiClear

®

Screen Surface: Reduces reflection and glare and increases contrast

without sacrificing focus level, clarity or brightness.

Dual Dynamic Beam Focus: Provides precise, continuous focus adjustments of

the electron beams resulting in optimum image quality, even to the far edges of

the screen.

AccuColor

®

Control System: Allows you to change between five color settings on

your display to match your personal preference.

OSM

™

(On-Screen Manager) Controls: Allow you to quickly and easily adjust all

elements of your screen image via simple to use on-screen menus.

ErgoDesign

®

Features: Enhance human ergonomics to improve the working

environment, protect the health of the user and save money. Examples include

OSM controls for quick and easy image adjustments, tilt/swivel base for pre-

ferred angle of vision and compliance with MPRII guidelines for lower emissions.

Plug and Play: The Microsoft

®

solution with the Windows

®

95/98/2000/Me/XP

operating system facilitates setup and installation by allowing the monitor to send

its capabilities (such as screen size and resolutions supported) directly to your

computer, automatically optimizing display performance.

IPM

™

(Intelligent Power Manager) System: Provides innovative power-saving

methods that allow the monitor to shift to a lower power consumption level when

on but not in use, saving two-thirds of your monitor energy costs, reducing

emissions and lowering the air conditioning costs of the workplace.

Reduced Magnetic Field

™

Technology: Reduces magnetic and alternating electric

field emissions and static electricity, addressing ergonomic concerns regarding

potential risks from extended computer monitor use.

Multiple Frequency Technology: Automatically adjusts monitor to the display

card’s scanning frequency, thus displaying the resolution required.

FullScan

™

Capability: Allows you to use the entire screen area in most resolu-

tions, significantly expanding image size.

GlobalSync

®

/Corner Purity Control: Allows you to easily adjust impurities in the

four corners of your monitor.

Convergence Control: Allows you to adjust the horizontal and vertical conver-

gence to ensure that a white line drawn on the screen is as crisp and clear as

possible.

Auto Adjust: Allows you to easily and quickly adjust and position for Non-preset timming.

GTF Auto Adjust: Automatically adjust horizontal and vertical size and position

settings according to GTF standard with the signal timing which Auto Adjust is

not available.

14

Features –continued

Constant Brightness: sustains the brightness and screen color levels consistently

over the normal life of the monitor.

SB (Super Brightness) Mode: Provides the screen brightness suitable for the

screen images displayed.

Super Bright Mode OFF: for text based images (normal use)

Super Bright Mode-1 ON: for images

Super bright Mode-2 ON: for moving image such as DVD movies

15

Troubleshooting

No picture

• Display card should be completely seated in its slot.

• Power Button and computer power switch should be in the ON position.

• Signal cable should be completely connected to display card/computer.

• Check connector for bent or pushed-in pins.

Image is scrolling or unstable

• Signal cable should be completely attached to the computer.

• Check pin assignments and signal timings of the monitor and your

display card with respect to recommended timings and pin assignments.

• If the Macintosh cable adapter is used, check for proper connection or

make sure the display card is Macintosh compatible and that the card is

properly seated in the computer.

LED on monitor is not lit

(no green, orange color can be seen)

• Power Switch should be in the ON position and power cord should

be connected.

Picture is fuzzy or color looks blotchy

• If the picture is fuzzy, adjust the Moiré Canceler control. If the color looks

blotchy, adjust the Brightness, Contrast or GlobalSync

®

controls, or use the

EdgeLock

™

control to change modes.

• Access the Degauss Control through OSM™ controls. Activate the

Degauss Control.

CAUTION: A minimum interval of 20 minutes should elapse before the

Deguass Control is used a second time when not switching

between modes.

Picture bounces or a wavy pattern is present

in the picture

• Move electrical devices that may be causing electrical interference away

from the monitor.

• See inside cover of User’s Manual for FCC information.

Edges of the display image are not square

• Use the OSM Geometry and Corner Correction Controls to straighten

the edges.

• If possible, position the front of the monitor facing east.

Display image is not centered, too small, or too large

• Use the OSM Size and Position Controls to adjust the image.

Thin lines appear on your screen

• Thin lines are normal for an aperture grille CRT and are not a malfunction.

These are shadows from the damper wires used to stabilize the aperture

grille and are most noticeable when the screen’s background is light

(usually white).

16

Troubleshooting –continued

Attention message displayed

• Check the inputted signal.

NOTE:The attention message may display when power on

the MultiSync monitor. In case that the attention

message disappear after in a little while, there is no

problem at the inputted signal.

Self check function

• Press any control button on the front of monitor when

you see a problem on the screen.

- In case that all R, G and B colors are seen in the

diagnosis message, the MultiSync monitor has no

problem. In case that some color is lack in the

message, the MultiSync monitor has a problem.

Contact NEC Customer Service.

- In case that no diagnosis message displayed with LED

lit in green, power off the computer.

• Check the signal cable and computer in case that the diagnosis message

displayed.

• Contact NEC Customer Service in case that the diagnosis message still

does not display.

- In case that no diagnosis message displayed with LED lit in orange.

• Check the signal cable and computer.

• Move the mouse or press any key on the keyboard.

- In case that no diagnosis message displayed with LED lit in green and

orange.

• Contact NEC Customer Service.

17

References

NEC-Mitsubishi Monitor Customer Service & Support

Customer Service and Technical Support:

(800) 632-4662

Fax: (800) 695-3044

Parts and Accessories/Macintosh

Cable Adapter: (888) NEC-MITS [888-632-6487]

Customer Service Policies & Processes: http://www.necmitsubishi.com/

css/ServicePolicies/ServicePolicies.htm

Online Technical Support

Knowledge Base: http://www.necmitsubishi.com/

css/knowledgebase.cfm

Customer Service & Technical

Support Email: http://www.necmitsubishi.com/

css/techform.htm

Sales and Product Information

Sales Information Line: (888) NEC-MITS [888-632-6487]

Canadian Customers: (866) 771-0266, Ext#: 4037

Government Sales: (800) 284-6320

Government Sales email: [email protected]

Electronic Channels

World Wide Web: http://www.necmitsubishi.com

Product Registration: http://www.necmitsubishi.com/

productregistration

European Operations: http://www.nec-mitsubishi.com

Windows

®

95/98/Me/2000/XP INF File:

http://

www.necmitsubishi.com and select

“Downloads and Drivers”

18

Limited Warranty

NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this

Product to be free from defects in material and workmanship and, subject to the conditions set

forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit

which proves defective for a period of three (3) years from the date of first consumer purchase.

Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or

refurbished and will meet specifications of the original parts or unit.

This warranty gives you specific legal rights and you may also have other rights, which vary

from state to state. This warranty is limited to the original purchaser of the Product and is not

transferable. This warranty covers only NMD-A-supplied components. Service required as a

result of third party components is not covered under this warranty. In order to be covered

under this warranty, the Product must have been purchased in the U.S.A. or Canada by the

original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by

NMD-A No warranty service is provided outside of the U.S.A. or Canada. Proof of Purchase

will be required by NMD-A to substantiate date of purchase. Such proof of purchase must be

an original bill of sale or receipt containing name and address of seller, purchaser, and the

serial number of the product.

It shall be your obligation and expense to have the Product shipped, freight prepaid, or

delivered to the authorized reseller from whom it was purchased or other facility authorized

by NMD-A to render the services provided hereunder in either the original package or a

similar package affording an equal degree of protection. All Products returned to NMD-A for

service MUST have prior approval, which may be obtained by calling 1-800-632-4662. The

Product shall not have been previously altered, repaired, or serviced by anyone other than a

service facility authorized by NMD-A to render such service, the serial number of the product

shall not have been altered or removed. In order to be covered by this warranty the Product

shall not have been subjected to displaying of fixed images for long periods of time resulting

in image persistence (afterimage effects), accident, misuse or abuse or operated contrary to

the instructions contained in the User’s Manual. Any such conditions will void this warranty.

NMD-A SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,

OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NMD-A PRODUCT

OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF ALL

OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE

LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAM-

AGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

This Product is warranted in accordance with the terms of this limited warranty. Consumers

are cautioned that Product performance is affected by system configuration, software, the

application, customer data, and operator control of the system, among other factors. While

NMD-A Products are considered to be compatible with many systems, specific functional

implementation by the customers of the Product may vary. Therefore, suitability of a Product

for a specific purpose or application must be determined by consumer and is not warranted

by NMD-A.

For the name of your nearest authorized NEC-Mitsubishi Electronics Display service facility,

contact NEC-Mitsubishi Electronics Display at 1-800-632-4662.

La page charge ...

NEC FE2111SB - MultiSync - 22" CRT Display Manuel utilisateur

NEC FE2111SB - MultiSync - 22" CRT Display Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents