iFit MP27-Argon2-E Tablet for Treadmill Mode d'emploi
- Taper
- Mode d'emploi
Instructions for the iFIT TABLE
operation
一，installation instructions
1、The 27table shipped by Yiwei is shown in the figure below：
2、The following detailed introduction and the assembly method of the
plastic shell are provided for customer reference, and customers can match
any shape design according to the requirements of the module 3D:
上盖
下盖
背面
二，operation declaration
1. After power-on, the display picture is such as (Figure 1)
graph 1
2. Click " " button to enter the next page and connect to WiFi network
(Figure 2)
graph 2
3. After successful network connection: click the setting language, the default
" " language need not be modified (Figure 3), directly click " " to enter
the next page such as (Figure
4)
graph 3
graph 4
4. Click the " " button in the top right corner (Figure 4) to
enter the following picture (Figure 5)
graph 5
4. Click the " " button to enter the main interface page (Figure
6)
graph 6
6. Click " " in the upper left corner of (Figure 6) to enter the (Figure 7)
page;
graph 7
7. Click (Figure 7) after the button " " starts; the page display (Figure
8). Click " " will enter the exercise warm-up page (Figure 9)
graph 8
graph 9
8. Click (Figure 9) " " and " " to adjust the speed and slope such
as (Figure 10)
graph 10
9. Click " " to connect to the Bluetooth headset, heart
rate device, click connect to connect to the searched device (Figure 11, Figure 12),
click any page Bluetooth connection pop-up page will be hidden.
graph 11
graph 12
10. After the warm-up, enter the video playback page (Figure 13), and the speed and
slope adjustment are the same as the above
graph 13
11. Click any page (Figure 13) screen to enter the setting page (Figure 14) to adjust
the volume, open the subtitles, connect the Bluetooth device, and end the movement
graph 14
12. Click " " to end the movement to the relaxation page (Figure
15)
graph 15
13. Click " " to end the movement to view the movement report (Figure
16)
graph 16
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and
operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
IC Caution:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Pour maintenir la conformité avec les directives d'exposition RF de la FCC, cet équipement doit
être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps : utilisez
uniquement l'antenne fournie.
Manufacturer's Name: IFIT HEALTH & FITNESS, INC.
Product Name: Tablet
Trade Mark: iFIT
Model number: MP27-Argon2-E, MP27-Argon2X-E
This device is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.
The device complies with RF specifications when the device used at 20cm from your
body.
The product shall only be connected to a USB interface of version USB2.0
RF Secification:
Function Operation Frequency Max RF outputpower: Limit
BLE 2402MHz–2480MHz 9.12dBm 20 dBm.
BT(BR+EDR) 2402MHz–2480MHz 9.18dBm 20 dBm.
WIFI 802.11b/g/
n(HT20,HT40)
802.11b/g/n(20MHz): 2412~2472MHz;
802.11n(40MHz):2422~2462MHz 16.58dBm 20 dBm.
Wi-Fi
5.2G(802.11a/n20/n4
0)
802.11a/ n20: 5180-5240MHz
802.11 n40: 5190-5230MHz 9.99dBm 23 dBm.
Wi-Fi
5.3G(802.11a/n20/n4
0)
802.11a/ n20: 5260MHz~5320MHz
802.11n(40MHz):5270~5310MHz 9.95dBm 23 dBm.
Wi-Fi
5.6G(802.11a/n20/n4
0)
802.11a/ n20: 5500MHz~5700MHz
802.11 n40: 5510MHz~5670MHz 9.93dBm 23dBm.
Wi-Fi
5.8G(802.11a/n20/n4
0)
802.11a/n20:5745MHz~5825MHz
802.11 n40:5755MHz~5795MHz 9.79dBm 13.98 dBm.
5150-5250MHz product for indoor use only
The use for 5.15-5.35GHz RLAN band is restricted to indoor use. This restriction will be
applied to all Member States of European Union.
DECLARATION OF CONFORMITY
I hereby declare that the product
Product Name: Tablet
Product Description: Tablet
Model: MP27-Argon2-E,MP27-Argon2X-E
Tradename or Brand(s): iFIT
(Name of product, type or model, batch or serial number)
Antenna :
FPC Antenna
2.16 dBi
Hard Ware Version: MT8163-21.5TG-A0
Soft Ware Version: com.ifit.eru-2.0.5.1213.apk,com.ifit.standalone-2.6.78.3818.apk,
com.ifit.launcher-1.0.17.22.apk
FW Version: Android 9
Satisfies all the technical regulations applicable to the product within the scope of Council Directives
2014/53/EU and declare that the same application has not been lodged with any other notified body.
ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301 893 V2.1.1 (2017-05)
ETSI EN 300 440 V2.2.1 (2018-07)
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-3 V2.1.1 (2019-03)
ETSI EN 301 489-17 V3.2.4 (2020-09)
EN 55032:2015+A11:2020
EN 55035:2017+A11:2020
EN IEC 61000-3-2:2019
EN 61000-3-3:2013+A1:2019
EN IEC 62311:2020
EN 62368-1:2014+A11:2017
(Title(s) of regulations, standards, etc.)
All essential radio test suites have been carried out.
NOTIFIED BODY: MiCOM Labs Inc
Address:
575 Boulder Court
Pleasanton
CA 94566, USA
Identification Number: 2280
MANUFACTURER or AUTHORISED REPRESENTATIVE:
Address:
ELectronic Way Technology Co., Ltd
No.268, South Jiguang Rd ShiPu Town, KunShan, JiangSu china 215342
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
