RemotePoint Emerald Navigator VP4450 Manuel utilisateur

Catégorie
Présentateurs sans fil
Taper
Manuel utilisateur
Users Manual
VP4450
Page 1
FCC Certication
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a CLASS B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a residential installation. This
equipment generates, uses, can radiate radio frequency energy and if not installed and used in
accordance with the instruction guide, may cause harmful interference to radio communications.
However, there is no guarantee that this radio interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Consult the dealer or an experienced Radio-TV technician for help.
Notice: Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. Extension cables are not
recommended, if used, they must be shielded in order to comply with the emission limits.
IC Certication
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour
l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la
Page 2
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à
l’établissement d’une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Declaration of Conformity
Manufacturer:
SMK-Link Electronics, Inc.
3601-B Calle Tecate
Camarillo, CA 93012
We declare under our sole responsibility that the VP4450 conforms to the following directives and
norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMI: EN 55022 (1992) Class B
EMC: EN 50082-1 (1992)
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
Page 3
LASER Safety Statement
CAUTION: Use of controls or adjustments or performance of
procedures other than those specied herein may result in hazardous
radiation exposure.
The laser is activated by pressing laser button identied in the user guide.
Do not stare into laser beam.
Do not shine a laser pointer at anyone.
Do not allow minors to use laser
pointer unsupervised.
Do not point laser pointer at any reective
surface. A reected beam can be the same
as a direct beam.
Do not disassemble the device.
Do not immerse in any liquid or expose
to heat or moisture.
Use only within the designed operating
temprature range of 0-40 deg C.
This product has no serviceable parts.
Laser Specications:
The following product complies as a Class 2 laser product with: IEC/EN
60825-1: 199+A1+A2, and CFR Title 21 1040.10 and 1040.11, except for
deviations pursuant to Laser Notice No.50, dated June 25, 2007.
Page 4
Page 5
Overview
Congratulations on your purchase of the VP4450 Emerald Navigator
Presentation Remote. The VP4450 offers full control of presentations,
customizable buttons to work with other programs, and the brightest laser
in its class.
Installation
Open the battery compartment by
pressing down on the latch and sliding
open. Insert the batteries per the
diagram on the remote. Standard AA
alkaline batteries are recommended.
The receiver and remote come pre-
paired at the factory. The remote
will automatically adjust frequencies
and channels to ensure reliable
communication.
Should you have any problem with
communication, you can re-pair them by
opening the battery door and plugging
the USB receiver into USB port below the
batteries. Plug the USB receiver into a free
USB port, wait a few seconds for the device
to be recognized by your computer and you
are ready to control your presentation.
Page 6
Familiarizing Yourself
with the Controls
Next Slide
Previous Slide
Blank Screen
Laser Pointer
Page 7
Using the Laser Pointer
Press the button on the top of the ring to activate the laser pointer. The
laser pointer can be used to highlight important points on slides and
graphs. Because the laser emits a green beam it will appear much brighter
than a standard laser beam.
Custom Programming
The buttons on the VP4450 can be customized to send a wide variety of
keystrokes to meet your needs. The software is available online at:
www.smklink.com
From the program, select the desired keys and click “Program Receiver.”
Once programmed, these changes are written to non-volatile memory on
the receiver.
Because the keys are stored on the receiver, any machine you plug it into
will send these keys without any need for software.
Page 8
Product Specications
Laser: 532 nm green class II laser
Laser Power: max < 1 mW
Battery Type: 2 x AA alkaline batteries
Battery Usage: Approx. six months
Frequency: 2.4 GHz auto RF
Range: Up to 100 feet
System Requirements
Operation:
Windows
®
or Mac
®
PC
USB port
Button Customizing
PC running Windows XP
®
and up
Downloadable software from:
www.smklink.com
Page 9
For Product Support Please Contact
SMK-Link Electronics, Inc.
3601-B Calle Tecate
Camarillo, CA 93012 USA
(888) 696-3500
(805) 987-6665
www.smklink.com
Thank you for purchasing the VP4450 RemotePoint
®
Emerald Navigator
Presentation Remote. We know you had other choices and we appreciate
that you chose SMK-Link Electronics for your wireless needs. So that we
may better serve you in the future, please register online at www.smklink.
com
Page 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

RemotePoint Emerald Navigator VP4450 Manuel utilisateur

Catégorie
Présentateurs sans fil
Taper
Manuel utilisateur

dans d''autres langues