Sollae Systems CSE-H55N2 Manuel utilisateur

Sollae Systems Co., Ltd.

https://www.ezTCP.com

RS422/485 - Ethernet Converter

CSE-H55N2 User Manual

Version 1.7

CSE-H55N2 User Manual Ver. 1.7

- 1 -

https://www.ezTCP.com

This symbol, found on your product or on its packaging, indicates that this

product should not be treated as household waste when you wish to dispose

of it. Instead, it should be handed over to an applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative consequences to the

environment and human health, which could otherwise be caused by inappropriate disposal

of this product. The recycling of materials will help to conserve natural resources. For more

detailed information about the recycling of this product, please contact your local city

office, household waste disposal service or the retail store where you purchased this

product.

※ This equipment obtained certification by using 1.5M serial cable.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

CSE-H55N2 User Manual Ver. 1.7 
 
 
- 2 - 
https://www.ezTCP.com 
 
 
Contents 
1 Overview .................................................................................................................................. - 5 - 
1.1  Overview ................................................................................................................................................................ - 5 - 
1.2  Features .................................................................................................................................................................. - 5 - 
1.3  Application Examples ....................................................................................................................................... - 6 - 
1.4  Specification ......................................................................................................................................................... - 9 - 
1.4.1
 
Hardware ...................................................................................................................................................... - 9 -
 
1.4.2
 
Software ........................................................................................................................................................ - 9 -
 
1.5  Interfaces ............................................................................................................................................................ - 10 - 
1.5.1
 
Serial Interface ........................................................................................................................................ - 10 -
 
1.5.2
 
Ethernet Interface .................................................................................................................................. - 12 -
 
1.5.3
 
Power ........................................................................................................................................................... - 13 -
 
1.6  System LED ........................................................................................................................................................ - 14 - 
1.6.1
 
Function button ...................................................................................................................................... - 15 -
 
2 Installation and Test ............................................................................................................ - 16 - 
2.1  Installation .......................................................................................................................................................... - 16 - 
2.1.1
 
Setting Network Area .......................................................................................................................... - 17 -
 
2.2  Simple Test ......................................................................................................................................................... - 19 - 
3 Configuration ....................................................................................................................... - 22 - 
3.1  Configuration with ezManager ................................................................................................................. - 22 - 
3.1.1
 
Configuration via LAN ......................................................................................................................... - 22 -
 
3.1.2
 
Configuration via Serial ...................................................................................................................... - 23 -
 
3.2  AT command ..................................................................................................................................................... - 24 - 
4 Operation Modes ................................................................................................................ - 25 - 
4.1  What is the Operation Mode? .................................................................................................................. - 25 - 
4.2  How to entering each mode ..................................................................................................................... - 25 - 
4.3  Comparison of each mode ......................................................................................................................... - 26 - 
4.4  Normal Mode ................................................................................................................................................... - 26 - 
4.5  Serial Configuration Mode ......................................................................................................................... - 27 - 
4.6  ISP Mode ............................................................................................................................................................ - 27 - 
4.6.1
 
Upgrading Firmware............................................................................................................................. - 27 -
 
4.6.2
 
Revoking Serurity Options................................................................................................................. - 27 -
 

CSE-H55N2 User Manual Ver. 1.7 
 
 
- 3 - 
https://www.ezTCP.com 
 
 
5 Communication Modes ...................................................................................................... - 28 - 
5.1  TCP Server .......................................................................................................................................................... - 28 - 
5.1.1
 
Key parameters ....................................................................................................................................... - 28 -
 
5.1.2
 
Examples .................................................................................................................................................... - 29 -
 
5.2  TCP Client ........................................................................................................................................................... - 32 - 
5.2.1
 
Key parameters ....................................................................................................................................... - 32 -
 
5.2.2
 
Examples .................................................................................................................................................... - 33 -
 
5.3  AT Command .................................................................................................................................................... - 36 - 
5.3.1
 
Key parameters ....................................................................................................................................... - 36 -
 
5.3.2
 
Examples .................................................................................................................................................... - 37 -
 
5.4  UDP ....................................................................................................................................................................... - 40 - 
5.4.1
 
Key parameters ....................................................................................................................................... - 40 -
 
5.4.2
 
Examples .................................................................................................................................................... - 41 -
 
6 System Management .......................................................................................................... - 43 - 
6.1  Upgrading Firmware ...................................................................................................................................... - 43 - 
6.1.1
 
Firmware .................................................................................................................................................... - 43 -
 
6.1.2
 
Processes ................................................................................................................................................... - 43 -
 
6.2  Status Monitoring ........................................................................................................................................... - 45 - 
6.2.1
 
Using TELNET .......................................................................................................................................... - 45 -
 
6.2.2
 
Using ezManager ................................................................................................................................... - 48 -
 
6.3  Factory Reset ..................................................................................................................................................... - 52 - 
6.3.1
 
Using Factory Reset .............................................................................................................................. - 52 -
 
6.3.2
 
Setting custom default values ......................................................................................................... - 53 -
 
7 Security Function ................................................................................................................. - 54 - 
7.1 SSL ......................................................................................................................................................................... - 54 - 
7.1.1 What is the SSL(Secure Socket Layer)?
 ...................................................................................... - 54 -
 
7.1.2 How to set the SSL
 ................................................................................................................................ - 54 -
 
7.1.3 Restriction
.................................................................................................................................................. - 55 -
 
7.2  Access Restriction (ezTCP Firewall) ......................................................................................................... - 56 - 
7.2.1
 
Setting Password .................................................................................................................................... - 56 -
 
8 Additional Functions ........................................................................................................... - 57 - 
8.1  Notify Ipv4 Change ........................................................................................................................................ - 57 - 
8.2  Sending MAC Address.................................................................................................................................. - 58 - 
8.3  Multiple Connection ...................................................................................................................................... - 59 - 

CSE-H55N2 User Manual Ver. 1.7 
 
 
- 4 - 
https://www.ezTCP.com 
 
 
8.3.1
 
How to use ............................................................................................................................................... - 59 -
 
8.3.2
 
Diagram ...................................................................................................................................................... - 59 -
 
8.4  Serial Port Tab Functions ............................................................................................................................. - 60 - 
8.4.1
 
Disable TCP Transmission Delay - ① ........................................................................................... - 60 -
 
8.4.2
 
Separator - ②.......................................................................................................................................... - 60 -
 
8.4.1
 
TCP Server / Client mode - ③ ........................................................................................................ - 61 -
 
8.4.2
 
Telnet COM Port Control(RFC2217) - ④..................................................................................... - 61 -
 
8.4.3
 
Data Frame Interval - ⑤ .................................................................................................................... - 61 -
 
9 RS485/RS422 Interface ....................................................................................................... - 62 - 
9.1 About RS485/RS422 Network ............................................................................................................... - 62 - 
9.2 Configuring an RS485 Network ............................................................................................................ - 62 - 
9.2.1 Signal Ground
 .......................................................................................................................................... - 62 -
 
9.2.2 Biasing Resistors
 .................................................................................................................................... - 63 -
 
9.2.3 Termination Resistors
 ........................................................................................................................... - 63 -
 
9.3 Configuring an RS422 Network ............................................................................................................ - 63 - 
9.3.1 1:1 Configuration
 .................................................................................................................................... - 63 -
 
9.3.2 1:N Configuration
 ................................................................................................................................... - 64 -
 
9.3.3 Signal Ground, Biasing and Termination Resistors
 ................................................................. - 64 -
 
10 Checklist in Trouble ............................................................................................................. - 65 - 
10.1 Searching problem with ezManager ...................................................................................................... - 65 - 
10.2 Connection Problem over TCP/IP ............................................................................................................ - 66 - 
10.3 Data Communication Problem over the Serial Port ....................................................................... - 67 - 
11 Technical Support and Warranty ...................................................................................... - 68 - 
11.1 Technical Support ........................................................................................................................................... - 68 - 
11.2 Warranty .............................................................................................................................................................. - 68 - 
11.2.1
 
Refund ......................................................................................................................................................... - 68 -
 
11.2.2
 
Free Repair Services ............................................................................................................................. - 68 -
 
11.2.3
 
Charged Repair Services..................................................................................................................... - 68 -
 
12 Precaution and Exemption from Liability ....................................................................... - 69 - 
12.1 Precaution........................................................................................................................................................... - 69 - 
12.2 Exemption from Liability .............................................................................................................................. - 70 - 
12.2.1
 
English version ........................................................................................................................................ - 70 -
 
12.2.2
 
French version ......................................................................................................................................... - 71 -
 
13 Revision History ................................................................................................................... - 73 - 

CSE-H55N2 User Manual Ver. 1.7

- 5 -

https://www.ezTCP.com

1 Overview

1.1 Overview

Almost all communication devices including PC are using serial transmission. In this type,

devices send and receive data in the order of each byte. The serial communication is quite

simple to implement but has weaknesses like short distance and hard maintenance.

To overcome those weaknesses, we offer “Serial Networking Solution” which allows the

serial devices to transmit/receive data over unlimited distance. CSE-H55N2 is one of “serial

networking” devices which lets the serial devices to connect to the Internet by converting

serial data to TCP/IP packet, and vice versa.

CSE-H55N2 is an upgrade version of CSE-H55N that has been designed to improve

stability against noise and electrical damage on RS422/485 line. There is no change in its

software

1.2 Features

⚫ IPv4 / IPv6 dual stack

⚫ Stateless / Stateful (DHCPv6) address auto-configuration

⚫ RS422/RS485 (Terminal Block)

⚫ Industrial temperature range (-40℃ ~ +85℃)

⚫ Variety of monitoring status (ezManager, TELNET)

⚫ Security Protocols SSL/TLS

⚫ Multiple connection for multi-monitoring



Multiple connection is supported in firmware version 2.3A or later.

CSE-H55N2 User Manual Ver. 1.7

- 6 -

https://www.ezTCP.com

1.3 Application Examples

⚫ 1:1 Connection with a PC

Figure 1-1 1:1 connection with a PC

⚫ Applied to LANs

Figure 1-2 applied to LANs

⚫ Applied to the Internet on Cable Networks

Figure 1-3 applied to the Internet on cable networks

CSE-H55N2 User Manual Ver. 1.7

- 7 -

https://www.ezTCP.com

⚫ Applied to the Internet with an IP Share Router

Figure 1-4 applied to the Internet with an IP share router

⚫ Applied to a serial tunneling system

Figure 1-5 applied to a serial tunneling system

⚫ Applied to a multi-drop network.

Figure 1-6 applied to a multi-drop network

CSE-H55N2 User Manual Ver. 1.7

- 8 -

https://www.ezTCP.com

⚫ An Example for Multiple Monitoring System

Figure 1-7 An Example for Multiple Monitoring System

CSE-H55N2 User Manual Ver. 1.7

- 9 -

https://www.ezTCP.com

1.4 Specification

1.4.1 Hardware

Power

Input Voltage

DC 5V (±10%)

Current

190mA typical

Dimension

94mm x 57mm x 24mm

Weight

About 64g

Serial Port

Serial

RS422 / RS485 (Baud Rate: 300bps ~ 230,400bps)

Network

10 Base-T or 100 Base-TX Ethernet Auto-Sensing

Auto MDI or MDIX cable Auto-Sensing

Temperature

Storage / Operating Temperature: -40 ~ 85℃

Approval

KC, CE, FCC

RoHS

RoHS Compliant

Table 1-1 Hardware specification

1.4.2 Software

Protocol

TCP, UDP, IPv4/IPv6 dual stack, , ICMPv6/TCPv6/UDPv6

ICMP, ARP, DHCP, PPPoE, DNS, DDNS(Dynamic DNS), Telnet, SSL

Operation

mode

Normal

For Normal Data Communication

ISP

For Upgrading F/W

Serial Configuration

For Configuration via Serial

Communicat

ion mode

TCP Server

TCP Passive Connection

TCP Client

TCP Active Connection

AT Command

TCP Passive / Active Connection

UDP

Major

Utilities

ezManager

Configuration Utility for MS Windows

(Supports Downloading F/W)

ezVSP

Serial to TCP/IP Virtual driver for MS Windows

Table 1-2 Software specification

CSE-H55N2 User Manual Ver. 1.7

- 10 -

https://www.ezTCP.com

1.5 Interfaces

1.5.1 Serial Interface

CSE-H55N2 has a serial port for user serial device (300bps ~ 230,400bps). This port is

interfaced with 6-pin terminal block and each pin should be fixed by a flat-head screwdriver

driver.

Figure 1-8 6 pins Terminal block

⚫ Pin Assignment for RS-422

Number

Name

Description

Level

I/O

Etc.

1

TX +

Transmit Data +

RS422

OUT

Required

2

TX -

Transmit Data -

3

GND

Ground

-

Required

4

RX +

Receive Data +

RS422

IN

Required

5

RX -

Receive Data -

6

GND

Ground

-

Required

Table 1-3 pin assignment of the RS422

⚫ Pin Assignment for RS-485

Number

Name

Description

Level

I/O

Etc.

1

TRX +

Transmit / Receive Data +

RS485

OUT

Required

2

TRX -

Transmit / Receive Data -

IN

3

GND

Ground

-

Required

6

GND

Ground

-

Required

Table 1-4 pin assignment of the RS485

CSE-H55N2 User Manual Ver. 1.7

- 11 -

https://www.ezTCP.com

⚫ Serial Port Parameters

Parameter

Value

Number

1

Type

RS422 / RS485

Baud rate

300 ~ 230,400 [bps]

Parity

NONE / EVEN / ODD / MARK / SPACE

Data bit

8 / 7

Stop bit

1 / 1.5 / 2

Flow control

NONE / RTS / CTS

Table 1-5 serial port parameters



When the ‘Data bit’ is set to 7, NONE parity cannot be used.

CSE-H55N2 User Manual Ver. 1.7

- 12 -

https://www.ezTCP.com

1.5.2 Ethernet Interface

Since part of CSE-H55N2 network is composed of Ethernet, UTP cable may be connected.

It will automatically sense 10Mbits or 100Mbits Ethernet and connect itself to network. It

also provides auto MDI/MDIX function that can automatically sense 1:1 cable or cross over

cable.

Figure 1-9 RJ45 the Ethernet interface

⚫ RJ45 the Ethernet port interface

Number

Name

Direction

1

TX+

Output

2

TX-

Output

3

RX+

Input

4

-

5

-

6

RX-

Input

7

-

8

-

Table 1-6 RJ45 the Ethernet port interface

⚫ Status of the system RJ45 LED

Color

LED status

Description

Yellow

Off

10 Mbps

On

100 Mbps

Green

On

Connecting with Ethernet

Off

Not connecting with Ethernet.

Blinking

Data is being transmitted

Table 1-7 LED status on the RJ45 LED

CSE-H55N2 User Manual Ver. 1.7

- 13 -

https://www.ezTCP.com

1.5.3 Power

CSE-H55N2 can be powered by 5VDC source via power jack. The specifications of the

power jack are as follows:

Figure 1-10 power jack

CSE-H55N2 User Manual Ver. 1.7

- 14 -

https://www.ezTCP.com

1.6 System LED

CSE-H55N2 has several lamps to show the current system status.

Each lamp shows the following status:

Mode

Name

Color

Status

Description

Common

PWR

Red

On

Supplying the power

LINK

Green

On

Connecting with Ethernet

RXD

Yellow

Blinking

Receiving data from the Ethernet

TXD

Green

Blinking

Sending data to the Ethernet

Normal

mode

STS

Yellow

Blinking in

every second

Obtaining an IP address

Blinking 4

times at once

Without obtaining an IP address via

DHCP or PPPoE network

On

Connecting with TCP

ISP mode

STS

Yellow

Off

Under ISP mode

Serial

Configuration

mode

STS

Yellow

Blinking

simultaneously

Under Serial Configuration mode

LINK

Green

RXD

Yellow

TXD

Green

Table 1-8 LED status on the top panel

Mode

Color

Status

Description

Common

Yellow

Blinking

Receiving data from the serial port

Green

Blinking

Sending data to the serial port

Table 1-9 LED status on the front panel

Figure 1-11 the front side panel



The green LED on the left side of RJ45 connecter is connected to a LINK LED and the

yellow LED on the right side indicates Ethernet speed. please refer to [Table1-7]

CSE-H55N2 User Manual Ver. 1.7

- 15 -

https://www.ezTCP.com

1.6.1 Function button

There is a switch, which is named function switch (or button) located on the side of the

product. You can change the operation mode of CSE-H55N2 to ISP or Serial Configuration

mode with this switch. And it is used for factory reset.

Figure 1-12 function switch

CSE-H55N2 User Manual Ver. 1.7

- 16 -

https://www.ezTCP.com

2 Installation and Test

2.1 Installation

Before testing CSE-H55N2, users should connect both serial and Ethernet port to a PC. To

connect the RS232 port of your PC and CSE-H55N2 via serial, you need a RS232 to

RS422/RS485 converter. It will be no problem that the Ethernet connection includes

network hubs.



In case if your PC doesn’t have a RS232 port, use a USB to RS232 cable.

Figure 2-1 connection between CSE-H55N2 and a PC

CSE-H55N2 User Manual Ver. 1.7

- 17 -

https://www.ezTCP.com

2.1.1 Setting Network Area

This step is for setting both CSE-H55N2 and users’ PC to be located the same network. If

only they are, the TCP connection between them can be established.

⚫ Setting of the PC

Add or change the IP address of the network adapter on your PC like following.

Get into the menu of [Windows Control Panel] >> [Network Connections] >>

[Properties of the Network Adapter – with right click of your mouse]. Then, you can

show the properties of [Internet Protocol (TCP/IP). In there, press the [Advanced..]

button for adding an IP Address like the below figure.

Figure 2-2 adding / changing the IP address of users’ PC

CSE-H55N2 User Manual Ver. 1.7

- 18 -

https://www.ezTCP.com

⚫ Setting of CSE-H55N2

CSE-H55N2 uses ezManager as it’s a configuration program. ezManager is for MS

Windows, and this is comfortable to use because it doesn’t need installation. First,

search your CSE-H55N2 via network. All the values of parameters are set the default

values in the factory. To apply it to your system, proper values should be set via

ezManager. Major parameters’ default values are listed on below table. To implement

this simple test, keep these values without any changes.

Name

Default Values

Network

Local IP Address

10.1.0.1

Subnet Mask

255.0.0.0

IPv6

Disable

Option

TELNET

Checked

IP Address Search

Checked

Serial Port

(COM1)

Serial Type

RS485

Baud Rate

19,200bps

Parity

NONE

Data Bits

8

Stop Bit

1

Communication mode

TCP Server

Local Port

1470

Table 2-1 default values of Major parameters



Refer to ezManager website for more details.

CSE-H55N2 User Manual Ver. 1.7

- 19 -

https://www.ezTCP.com

2.2 Simple Test

If you press the [Simple Test] button, test program will be shown on your screen.

⚫ Connecting to the CSE-H55N2 via LAN

Figure 2-3 settings for TCP connection

① Select [TCP Client]

② Input correct IP address and port number of CSE-H55N2

③ Clink the [Connect] button. (In case of TCP Server, it will be [Listen] button)

⚫ Opening RS232 Port

Figure 2-4 opening COM Port

④ Select COM port where the CSE-H55N2 is being connected.

⑤ Make sure that all the parameters are the same with CSE-H55N2.

⑥ Press the [Open] button

La page charge ...

Sollae Systems CSE-H55N2 Manuel utilisateur

Sollae Systems CSE-H55N2 Manuel utilisateur

dans d''autres langues