wattstopper LMRC-111-M Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

Wattstopper
®
Conduit Adapter for J-Box Mounting LMRC-111/112
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 30737 – 08/20 rev. 1
Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo: LMRC-1CA
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION AND OPERATION
The LMRC-1CA is a 3/4” KO conduit adapter designed to enable the LMRC-11x 10A rated room controllers to be
mounted inside an electrical junction box to meet local electrical codes where all wiring is required to be installed
inside of a conduit. For proper mounting, the minimum J-Box dimensions are 4-11/16” square by 2-1/8” deep with 3/4”
knockouts (also known as a 5” box or 11B).
NOTE: For City of Chicago applications a sealed J-Box is required. Recommended J-Box is Garvin Industries item
number 72171-3/4-VT (or equivalent)
NOTE: The LMRC-1CA is not recommend for use with the LMRC-111-16M due to operating temperature issues.
INSTALLATION
1. If desired a 3/4” rigid box spacer (not included) can be used to help secure the two J-Boxes together. If using, remove the outer
knockouts on one side of the J-Box and then attach the rigid box spacer to the J-Box that will hold the LMRC-111/112. Otherwise,
remove only the knockout corresponding to the location of the nipple on the LMRC-11x.
2. Insert the LMRC-11x into the J-Box with the wires sticking out of the knockout opening. Adjust the nut on the nipple so that the
nipple extends out of the J-Box at least 1/4”.
3. Screw the conduit adapter onto the nipple with the notched triangle pointing away from the J-Box, as shown below. The conduit
adapter should turn about 2 to 2 1/2 times before tightening. The triangle should be facing up, as shown.
4. Attach the J-Box with the room controller to the J-Box connected to the conduit, using locking nuts to secure.
3/4 in. Rigid
Box Spacer
Conduit
Adapter
Nipple from
LMRC-111/112
should extend out
from J-Box at least 1/4”
Conduit
Adapter
3/4 in. Rigid Box Spacer
(Optional, Not Included)
Load
Example showing LMRC connected to conduit box and
load, with line voltage and Class 1 dimming wires
800.879.8585
www.legrand.us/wattstopper
No. 30737 – 08/20 rev. 1
© Copyright 2020 Legrand All Rights Reserved.
© Copyright 2020 Tous droits réservés Legrand.
© Copyright 2020 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
  • Page 1 1
  • Page 2 2

wattstopper LMRC-111-M Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à