Bertazzoni REF30PIXL Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à

INSTALLATION GUIDE
NOTICE D’INSTALLATION
EN
FR
REF30PIXL
REF30PIXR
REF30PRL
REF30PRR
REF36PIXL
REF36PIXR
REF36PRL
REF36PRR
IMPORTANT
Dimensions in parentheses are in inches: mm(in).
Weights in parentheses are in pounds: kg (lb).
Temperatures in parentheses are in Fahrenheit degrees: °C(°F)
1
3
4
5
6
7
8
10
11
13
14
15
16
18
19
21
22
23
24
25
Installation Guide
EnglishFrançais
Index
Page
Important Instructions
Important safety instructions
Children safety
Technical Requirements
Appliance features and installation requirements
Installation niche features: Integrated Series (BI)
Installation niche requirements: Stainless Integrated Series (BKI)
Preparing To Install
Transport to installation site and unpacking
Electrical and Water connection
Levelling
Panels Mounting
Door and Bottom-Drawer overlay panels layout
Overlay panels mounting brackets layout
Panels Dimensions
Mounting the handles on Integrated units
Mounting panels to the door and the drawer of Integrated units
Installation
Built-in installation of single appliance
Built-in installation of two or more appliances
Completing The Installation
Anti-tipping safety assembly
Mounting handles on stainless front
Air circulation
Post installation checklist
Start Up
2
3
Installation Guide
Series: All
EnglishFrançais
Symbols used in the Guide
Note
Tips for the correct use of the appliance
Warning
Directions to prevent injury
Important
Directions to avoid appliance damage
Important safely instruction
Children safety
DANGER: Risk of child entrapment. Before you throw away your old
refrigerator or freezer:
Take off the doors
Leave the shelves in place so that children may not easily climb
inside.
ATTENTION
This appliance must be transported in an upright position. If this was
not the case you should leave it upright for 24 hours prior to switch it
on.
Take maximum care during handling to avoid harm to persons and
property.
Secure the top of the appliance to the wall with the two brackets
provided with the appliance.
24 h
!! ATTENZIONE !! - !! ATTENTION !!
CONTENUTO IMBALLO - PACKING CONTENTS
CONTENUTO KIT ACCESSORI - OWNER KIT CONTENTS
Descrizione - Description
StandPlus/
X-pro
Integrated Classic
Apparecchiatura
Appliance
Staffe, squadrette, viti, chiave per ssare pannelli esterni
Fasteners, brackets, screws, wrench for mounting outer panels
Prolati in alluminio per chiusura spazi tra apparecchiature e mobili
Alluminium trims to ll gap between appliance and cabinets
Kit accessori (all’interno dell’apparecchiatura)
Owner’s Kit (inside the appliance)
Descrizione - Description
Modelli con Ice
Maker - Models
with Ice Maker
Modelli senza Ice
Maker - Models
without Ice Maker
Tubo di collegamento alla rete idraulica (solo modelli con Ice Maker)
Water ll hose (only models with Ice Maker)
Filtro acqua (solo modelli con Ice Maker)
Water lter (only models with Ice Maker)
Piedini livellatori
Leveling feet
Squadrette antiribaltamento, tasselli e viti per il ssaggio delle squadrette antiribaltamento
Anti-tipping brackets, xing plugs and screws
Kit per la pulizia dell’apparecchiatura
Appliance cleaning kit
Manuale d’uso, guida di installazione, certicato di garanzia
User Manual, Installation Guide, Guarantee Certicate
Leggete con attenzione e conservate con cura la Guida Installazione e il Manuale d’uso forniti con l’apparecchiatura.
Read the User Manual and the Guide attentively and keep it in a safe place.
13-04-12 / B09010102 ML
24 h
!! ATTENZIONE !! - !! ATTENTION !!
CONTENUTO IMBALLO - PACKING CONTENTS
CONTENUTO KIT ACCESSORI - OWNER KIT CONTENTS
Descrizione - Description
StandPlus/
X-pro
Integrated Classic
Apparecchiatura
Appliance
Staffe, squadrette, viti, chiave per ssare pannelli esterni
Fasteners, brackets, screws, wrench for mounting outer panels
Prolati in alluminio per chiusura spazi tra apparecchiature e mobili
Alluminium trims to ll gap between appliance and cabinets
Kit accessori (all’interno dell’apparecchiatura)
Owner’s Kit (inside the appliance)
Descrizione - Description
Modelli con Ice
Maker - Models
with Ice Maker
Modelli senza Ice
Maker - Models
without Ice Maker
Tubo di collegamento alla rete idraulica (solo modelli con Ice Maker)
Water ll hose (only models with Ice Maker)
Filtro acqua (solo modelli con Ice Maker)
Water lter (only models with Ice Maker)
Piedini livellatori
Leveling feet
Squadrette antiribaltamento, tasselli e viti per il ssaggio delle squadrette antiribaltamento
Anti-tipping brackets, xing plugs and screws
Kit per la pulizia dell’apparecchiatura
Appliance cleaning kit
Manuale d’uso, guida di installazione, certicato di garanzia
User Manual, Installation Guide, Guarantee Certicate
Leggete con attenzione e conservate con cura la Guida Installazione e il Manuale d’uso forniti con l’apparecchiatura.
Read the User Manual and the Guide attentively and keep it in a safe place.
13-04-12 / B09010102 ML
24 h
!! ATTENZIONE !! - !! ATTENTION !!
CONTENUTO IMBALLO - PACKING CONTENTS
CONTENUTO KIT ACCESSORI - OWNER KIT CONTENTS
Descrizione - Description
StandPlus/
X-pro
Integrated Classic
Apparecchiatura
Appliance
Staffe, squadrette, viti, chiave per ssare pannelli esterni
Fasteners, brackets, screws, wrench for mounting outer panels
Prolati in alluminio per chiusura spazi tra apparecchiature e mobili
Alluminium trims to ll gap between appliance and cabinets
Kit accessori (all’interno dell’apparecchiatura)
Owner’s Kit (inside the appliance)
Descrizione - Description
Modelli con Ice
Maker - Models
with Ice Maker
Modelli senza Ice
Maker - Models
without Ice Maker
Tubo di collegamento alla rete idraulica (solo modelli con Ice Maker)
Water ll hose (only models with Ice Maker)
Filtro acqua (solo modelli con Ice Maker)
Water lter (only models with Ice Maker)
Piedini livellatori
Leveling feet
Squadrette antiribaltamento, tasselli e viti per il ssaggio delle squadrette antiribaltamento
Anti-tipping brackets, xing plugs and screws
Kit per la pulizia dell’apparecchiatura
Appliance cleaning kit
Manuale d’uso, guida di installazione, certicato di garanzia
User Manual, Installation Guide, Guarantee Certicate
Leggete con attenzione e conservate con cura la Guida Installazione e il Manuale d’uso forniti con l’apparecchiatura.
Read the User Manual and the Guide attentively and keep it in a safe place.
13-04-12 / B09010102 ML
24 h
!! ATTENZIONE !! - !! ATTENTION !!
CONTENUTO IMBALLO - PACKING CONTENTS
CONTENUTO KIT ACCESSORI - OWNER KIT CONTENTS
Descrizione - Description
StandPlus/
X-pro
Integrated Classic
Apparecchiatura
Appliance
Staffe, squadrette, viti, chiave per ssare pannelli esterni
Fasteners, brackets, screws, wrench for mounting outer panels
Prolati in alluminio per chiusura spazi tra apparecchiature e mobili
Alluminium trims to ll gap between appliance and cabinets
Kit accessori (all’interno dell’apparecchiatura)
Owner’s Kit (inside the appliance)
Descrizione - Description
Modelli con Ice
Maker - Models
with Ice Maker
Modelli senza Ice
Maker - Models
without Ice Maker
Tubo di collegamento alla rete idraulica (solo modelli con Ice Maker)
Water ll hose (only models with Ice Maker)
Filtro acqua (solo modelli con Ice Maker)
Water lter (only models with Ice Maker)
Piedini livellatori
Leveling feet
Squadrette antiribaltamento, tasselli e viti per il ssaggio delle squadrette antiribaltamento
Anti-tipping brackets, xing plugs and screws
Kit per la pulizia dell’apparecchiatura
Appliance cleaning kit
Manuale d’uso, guida di installazione, certicato di garanzia
User Manual, Installation Guide, Guarantee Certicate
Leggete con attenzione e conservate con cura la Guida Installazione e il Manuale d’uso forniti con l’apparecchiatura.
Read the User Manual and the Guide attentively and keep it in a safe place.
13-04-12 / B09010102 ML
4
BI30 w: 749 mm (29 1/2”)/ h: 2120 mm (83 1/2”)/ d: 610 mm (24”)
BI36 w: 899 mm (35 3/8”)/ h: 2120 mm (83 1/2”)/ d: 610 mm (24”)
BKI30 w: 749 mm (29 1/2”)/ h: 2120 mm (83 1/2”)/ d: 635 mm (25”)
BKI36 w: 899 mm (35 3/8”)/ h: 2120 mm (83 1/2”)/ d: 635 mm (25”)
30” Series w: 800 mm (31 1/2”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
36” Series w: 950 mm (37 3/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
30” Series up to 275 kg (606 lb)
36” Series up to 295 kg (650 lb)
North America Version: 115V 60Hz
North America Version: 15 A
from 0.05 MPa to 0.5 MPa (0.5 Bar - 5 Bar)
3/4” female attachment
Customized panels mounting Kit
Anti-tipping Kit (B04000200)
Lateral connecting kit (KCLIT/KCLIH)
4 mm (1/8”) allen wrench
Phillips head screwdriver
wood and percussion drill
2.5 mm (1/8”) bit for wood
8 mm (3/8”) bit for walls
17 mm (3/4”) wrench
13 mm (1/2”) socket
Appliance dimensions
Integrated
Appliance dimensions
Stainless Integrated
Appliance dimensions
with packaging
Weight with packaging
Voltage
Power supply cable
Potable water supply pressure
Water connection
Provided installation accessories
Additional equipment necessary
Adjusting height of the rear rollers
Appliance features and installation requirements
Note
Not all models come with an automatic
ice maker. Verify if your model is equipped
with an ice maker to determine if you
require water supply.
Description
Maker - Models
with Ice Maker
Maker - Models
without Ice
Maker
Water fill hose (only models with Ice Maker)
Water filter (only models with Ice Maker)
Leveling feet
Anti-tipping brackets, fixing plugs and screws
Appliance cleaning kit
User Manual, Installation Guide, Guarantee Certificate
Description
StandPlus/
X-pro
Integrated Classic
Appliance
Fasteners, brackets, screws, wrench for mounting outer panels
Alluminium trims to fill gap between appliance and cabinets
Owner’s Kit (inside the appliance)
Read the User Manual and the Guide attentively and keep it in a safe place.
5
140 (5 ½”) 140 (5 ½”)
100 (4”)
100 (4”)
A A
min 2134 (84”)
BI36: 900 (35 ½”)
BI30: 750 (29 5⁄8”)
A
2134 mm (84”)
BI36: 900 mm (35 1/2”)
BI30: 750 mm (29 5/8”)
BI36: 1470 mm (57 7/8”)
BI30: 1320 mm (52”)
105°
BI36: 899 mm (35 3/8”)
BI30: 749 mm (29 1/2”)
2120 mm (83 1/2”) + 25 mm (1”)
610 mm (
24”)
610 (24”)
560 (22”)
1293 (50 7⁄8” )
474 (18 5⁄8”)
231 (9
1⁄8”
) +
25 (1”)
500 (19 ¾”)
248 (9
¾”
)
+ 25 (1”)
20 (¾”)
721 (28 3⁄8”) +25 (1”)
2120 (83 ½”) +25 (1”)
992 (39”)
BI36: 1470 (57
7⁄8”
)
BI30: 1320 (52”)
BI36: 160 (6 3⁄8”)
BI30: 125 (5”)
560 (22”)
610 (24”)
BI36: 899 (35 3⁄8”)
BI30: 749 (29 ½”)
10 (3⁄8”)
105°
Installation Guide
EnglishFrançais
Installation niche features: Integrated Series (BI)
BI30 w: 749 mm (29 1/2”)/ h: 2120 mm (83 1/2”)/ d: 610 mm (24”)
BI36 w: 899 mm (35 3/8”)/ h: 2120 mm (83 1/2”)/ d: 610 mm (24”)
BKI30 w: 749 mm (29 1/2”)/ h: 2120 mm (83 1/2”)/ d: 635 mm (25”)
BKI36 w: 899 mm (35 3/8”)/ h: 2120 mm (83 1/2”)/ d: 635 mm (25”)
30” Series w: 800 mm (31 1/2”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
36” Series w: 950 mm (37 3/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
30” Series up to 275 kg (606 lb)
36” Series up to 295 kg (650 lb)
North America Version: 115V 60Hz
North America Version: 15 A
from 0.05 MPa to 0.5 MPa (0.5 Bar - 5 Bar)
3/4” female attachment
Customized panels mounting Kit
Anti-tipping Kit (B04000200)
Lateral connecting kit (KCLIT/KCLIH)
4 mm
(1/8”) allen wrench
Phillips head screwdriver
wood and percussion drill
2.5 mm (1/8”) bit for wood
8 mm (3/8”) bit for walls
17 mm (3/4”) wrench
13 mm (1/2”) socket
area to be left clear for the anti-tipping brackets
Niche Height
Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door (without panel)
6
1
4
1
2
3
140 (5 ½”) 140 (5 ½”)
100 (4”)
100 (4”)
A A
min 2134 (84”)
BI36: 900 (35 ½”)
BI30: 750 (29 5⁄8”)
A
2134 mm (84”)
BKI36: 900 mm (35 1/2”)
BKI30: 750 mm (29 5/8”)
BKI36: 1470 mm (57 7/8”)
BKI30: 1320 mm (52”)
105°
BKI36: 899 mm (35 3/8”)
BKI30: 749 mm (29 1/2”)
2120 mm (83 1/2”) + 25 mm (1”)
635 mm (25”)
2120 (83 ½”) +25 (1”)
635 (25”)
560 (22”)
693 (27 ¼”)
1308 (51 ½”)587 (23 1⁄8”)
146 (5 ¾”)
+ 25(1”)
9 ( 3⁄8”)
732 (28 7⁄8”)+25 (1”)
BKI30: 1320 (52”)
560 (22”)
635 (25”)
BKI36: 899 (35 3⁄8”)
BKI30: 749 (29 ½”)
10 (3⁄8”)
105°
75 (3”)
58 (2 ¼”)
BKI36: 230 (9)
BKI30: 195 (7 ¾”)
Series: All
Installation niche requirements: Stainless Integrated Series (BKI)
area to be left clear for the anti-tipping brackets
Niche Height
Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door (without panel)
7
1
4
1
2
3
105°
BKI36: 899 mm (35 3/8”)
BKI30: 749 mm (29 1/2”)
2120 mm (83 1/2”) + 25 mm (1”)
635 mm (25”)
Installation Guide
Series: All
EnglishFrançais
The appliance is very heavy.
Take maximum care during handling to
avoid injury.
The appliance should always be transport-
ed in an erect position.
Avoid at all costs leaning it on its front side.
Preparing the installation
Transport to installation site
and unpacking
Since this is a large and heavy appliance, before transporting the ap-
pliance, check the access to the location where it will be installed
(door size, manoeuvring space in stairwells, etc.).
The appliance is attached to the base of the packaging (pallet)
through four bolts which can be removed using a 17 mm (3/4”) wrench.
It is recommended to use a manual transporting device to move the
appliance to the installation site, and only at this point to remove the
base of the packaging.
The appliance should always be transported in an erect position.
If this is not possible, transport the appliance laying on its rear side.
Once at the installation site, the appliance, which is equipped with four
wheels, can be taken off the pallet and positioned in the installation
area.
Operate as follows:
Take off the four bolts
1
securing the appliance to the pallet by
means of a 17 mm (3/4”) wrench or socket.
Remove the xing brackets
3
and
4
.
To remove the front xing bracket
3
, unscrew for one or two turns
the rear wheel adjusting bolt
2
by means of a 13 mm (1/2”) socket,
do not overtighten the nut as it could damage the leveling feet adjust-
ing system.
From the back of the unit and by means of a suitable, high duty hand
trolley, take off the appliance and place it on the oor. Be mindful of
any debris on the oor which could get caught under the rollers and
potentially damage the ooring when moving the appliance.
Be very careful to avoid any damage to oors. Delicate oors should be
protected with plywood, hard cardboard or similar material panels.
Door Opening Angle
Width
Height
Depth with door (without panel)
EW
E W
EW
E W
8
E
W
E
W
Series: All
The appliance should be connected only to
a drinkable water supply system.
The Built-in lter cannot make it safe to
drink any water which is not suitable for hu-
man consumption.
Electrical and Water connection
Do not use extension cords or adapters.
Once the appliance is fully installed, connected
to the water supply (if applicable) and opera-
tional, in the event that the water supply must be
turned off,(touch the button
on control panel
to switch it off) before the main water is shut off to
prevent the appliance from entering a ‘NO WATER
IN’ alarm state.
Water connection
Electrical connection
Electrical and water supply behind the unit
Integrated Series
The appliances are delivered from the factory for operation at 110V-
120V AC - 60Hz (US and Canada).
Do not connect the refrigerator to any GFCI receptacle.
They are provided with a suitable supply cable and plug to be con-
nected to an appropriate 15A socket (US and Canada) provided
with an effective grounding.
A circuit breaker should also be installed and should be easily ac-
cessible so that it can be easily switched off before performing any
installation or maintenance.
To connect to the water supply system (for appliances equipped with
ice makers) a 1/4” waterline with accessible shut-off valve must be
supplied.
The appliance is provided with a water adapter elbow which is suit-
able for high water pressure and complies the Food Regulations.
The water lter cartridge, which is provided with the appliance,
should be installed according to the accompanying instructions. Use
only the new adapter which is supplied with the appliance. The so-
lenoid connection on the appliance is 3/4” diameter but is metric
threaded. A standard garden hose threaded connector such as a
braided stainless hose found at typical hardware stores will strip or
damage the solenoid threads. Use only the supplied 1/4” quick con-
nect elbow adapter for connecting a 1/4” copper or polyethylene
source water line to the appliance.
Electrical cord length: 2500 mm (98 3/8”)
Water connection line length: 2500 mm (98 3/8”)
Do not use extension cords and/or multiple adapters for the power
supply connection.
9
Installation Guide
EnglishFrançais
Series: All
Back of appliance
Water connection
Electrical connection
Operate as follows:
Unwind the electric cable and connect it directly to the wall socket.
Make sure the appliance is in the Stand-by condition and that all
lights are off; should it be not so press the Unit button to switch it off.
Push the 1/4” source waterline fully into the elbow connector then
thread the elbow adapter to the solenoid at the back of the appli-
ance.
Firmly tighten with ngers - a tool / wrench should not be needed to
make a proper seal. Turn on the water and ensure all connections
are not leaking prior to pushing the unit into the niche.
10
1
2
1
2
Series: All
Adjust the appliance level by means of the front levelling feet
and the rear adjustable wheels.
Operate as follows:
The grille should ship taped to the back of the appliance. If by chance
it is already in place, remove the grille (it is kept in position by magnets),
adjust the height of the levelling feet
1
by means of a 17
mm (3/4”) wrench.
Then adjust the height of the rear wheels by turning the front adjusting
bolts
2
clockwise or counter-clockwise as it may be required. (Do
not use power drivers with high torque settings for this step as it could
damage the levelling mechanism)
Mount the lower ventilation grille only after the unit is nally levelled
in the niche.
Levelling
11
1
2
3
Installation Guide
EnglishFrançais
Series: Integrated (BI)
Door and Bottom-Drawer overlay panels layout
The dimensions of the panels are indicated in the table and draw-
ings on pages 13.
Nevertheless, according to the requirements for aligning with other
kitchen structures, the door panel can be higher than the upper
edge of the refrigerator door, and the drawer panel can be lower
than the edge of the drawer.
The panels must be mounted using special braces which attach
to adjustable devices provided on the door and drawer and with
brackets that anchor and adjust the panel’s vertical direction.
Braces, brackets and fixing screws are provided with the appliance
and must be applied to the panel as indicated.
Operate as follows:
To prepare the panels to be mounted on the appliance, follow
these steps, working on the back of the panel.
Door Panel
Draw a reference center line, dividing the panel width in half
1
.
Starting from the bottom edge of the panel, mark the positioning
of the brackets
2
.
Following the corresponding table, mark the outside and then the
inside hole
3
.
12
7
8
4
5
Series: Integrated (BI)
Position the brackets on each set of marks to make sure they are
aligned
4
, you may wish to drill pilot holes (pay close attention to
the panel’s thickness)
5
.
Screw the brackets in place
6
.
Drawer Panel
When preparing the Drawer Panel, follow the same instructions as
per the door panel, but make sure measurements are taken starting
from the top edge
7
. The support bracket faces the opposite way
8
(note imgs 4 and 8).
13
A
BB
A
BB
C C
13 (½”)
34 (1
3⁄8”)
6,5 (
¼”)6,5 (¼”)
34 (1
3⁄8”)
1273 (50 1⁄8”)
1163 (45 ¾”)
660 (26”)
157 (6
¼”)
min 1390 (54
¾”)max 635 (25”)
507.5 (20”)
382 (15
1⁄8”)
100 (4”)
A
897 (35
¼”) 747 (29 3⁄8”)
417 (16
3⁄8”) 342 (13 ½”)
597 (23 ½”)
B
C
354.5 (14”) 279.5 (11”)
203.5(8”)
Installation Guide
EnglishFrançais
Series: Integrated
Overlay panels mounting brackets layout
Series 36
Series 30
Holes positions
Door panel
Back of the panel
Vertical adjustment bracket for
upper door. Note orientation.
Note: All lateral bracket placement
measurements go from the center line
to the outside bracket hole
Vertical adjustment bracket for
lower drawer. Note orientation.
Back of the panel
Drawer panel
14
2121 (83
½
") + 25 (1")
min 540 (21 ¼”)
max 635 (25”)
A
B
3 (1⁄8”)
1390 (54 ¾”)
115 (4 ½”)
min 200 (7 7⁄8”)
135
(5 3⁄8”)
135
(5 3⁄8”)
1075 (42 3⁄8”)
900 (35 1/2”)
750 (29 5/8”)
BI36
BI30
897 (35 1/4”)
747 (29 3/8”)
Series: Integrated (BI)
Door/Drawer Width Niche Width
Series
Panels Dimensions
Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“).
Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum weight of 11kg (25 lbs)
Exceeding these weights could void your warranty for any service issues which can be attributed to overweight panels.
The hinging mechanism on appliances is considered to be `Zero-clearance`. The door and drawer widths specified below
assume the minimum niche width is being used and a 3.5mm (1/8”) reveal is desired around the panels. Adjust your panel
dimensions accordingly to your own design criteria considering your niche width and your reveal. Minimum reveal / gap
should not be less than 1.5mm (1/16”).
Example:
84” niche height
36” niche width
4” toe kick height
1/8” gap desired all around
Door panel:
Width: 35-3/4”
Height: 54-3/4”
Drawer panel:
Width: 35-3/4”
Height: 84”-1/8”-54-3/4”-1/8”-4”=25”
If you want a 6” toe kick height then your
bottom drawer panel height would be 23”
15
1
2
480 mm
(18 7/8”)
900 mm
(35 1/2”)
490 mm
(19 1/4”)
Installation Guide
EnglishFrançais
Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“).
Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum weight of 11kg (25 lbs)
Exceeding these weights could void your warranty for any service issues which can be attributed to overweight panels.
The hinging mechanism on appliances is considered to be `Zero-clearance`. The door and drawer widths specified below
assume the minimum niche width is being used and a 3.5mm (1/8”) reveal is desired around the panels. Adjust your panel
dimensions accordingly to your own design criteria considering your niche width and your reveal. Minimum reveal / gap
should not be less than 1.5mm (1/16”).
Series: Integrated (BI)
Mounting the handles on Integrated units
Distance between stand-offs X
Handles will have to be mounted on the panels before they are ap-
plied to the fridge. For overlay panel mounting, remove the screw
connecting the stand-offs to the handle bar. The overlay screw will
pass through the overlay panel, the stand-off and into the handle
bar.
Operate as follows:
Drill two holes of 5 mm (1/4 “) on the rear side panels, in-
sert the supplied screws to the distance indicated in the
the table below. To center the vertical handle (code HV) to
the center of the door, split into two the height of the panel and make
a hole at -450 mm (-17 3/4”) and one at +450 mm (+17 3/4”)
1
.
Place the handle on top of the holes and insert the screws through
the panel and into the handle support
2
.
16
1
2
3
4
5
Mounting panels to the door and the drawer of Integrated units
Install 1 hanger bolt about 3 threads deep and 1 depth set screw
ush to foam gasket in each mounting cavity.
Once all brackets and small brackets have been applied to the pan-
els, you can begin installing the bottom drawer.
Operate as follows:
Partially install the adjustment bolt with washer into the two holes
in the bottom of the drawer
1
.
Ensure the L-brackets align with the adjustment bolts on the bot-
tom, place panel against the drawer face with the hanger brackets
above the hanger bolts and allow the panel to drop down. Ensure all
the hanger brackets engage the hanger bolts
2
.
It is now possible to align panels to adjacent cabinets in height us-
ing the lower alignment brackets,
3
tightening or untighteningthe
bolts into position as needed. With the hanger bolts slighty tightened,
move the panel sideways to align it to the other panels on the unit
or other adjacent structures. Tapping the panel with a rubber mallet
is a good way to make small adjustments to the X-alignment of the
panel.
Depth alignment: working from the inside of the drawer, after lift-
ing up the magnetic seal, adjust the panel position so it is closer to or
further away from the door using the holes
4
and then secure the
panel using the holes
5
.
Turning in the direction of the thick arrow pulls the panel closer to the
door / drawer face, turning in the direction of the thin arrow pushes
the panel away from the face of the door / drawer.
Series: Integrated (BI)
Once the front panel has been ad-
justed, check that the gasket has
been repositioned correctly to as-
sure the door/drawer are closing
correctly and avoid operational er-
rors of the unit.
17
6
8
9
7
10
11
Installation Guide
EnglishFrançais
Series: Integrated (BI)
Ensure the top adjustment L-brackets are aligned and inserted
into the cavities at the top of the door
6
.
Make sure all the hanger brackets begin above the hanger bolts
and then lower the panel down checking that each hanger brack-
et has engaged its corresponding hanger bolt.
At this point, alignment between the panel and adjacent cabi-
nets can be adjusted using the alignment brackets and small brack-
ets
7
and
8
.
Vertical alignment: tighten or loosen the screw in the brackets to
raise or lower the panel
9
.
Depth alignment: working from the inside of the door, after lift-
ing up the magnetic seal, adjust the panel position so it is closer to
or further away from the door using the holes
10
and then fix the
panel in position using the holes
11
.
Once the front panel has been ad-
justed, check that the gasket has
been repositioned correctly to as-
sure the door/drawer are closing
correctly and avoid operational er-
rors of the unit.
18
2
3
1
B
A
6,5 (¼”) 6,5 (¼”)
20 (¾”)
20 (¾”)
22 (7⁄8”)
22 (7⁄8”)
22 (7⁄8”) 22 (7⁄8”)
Series: All
Installation
For a built-in installation, to close gaps between the appliance and
the adjacent cabinets, special side proles (installed) and aluminum
trim covers (taped to back of appliance) are provided. Side proles
are used for xing the appliance to the niche cabinet and can be
shimmed from the side of the appliance in order to match the niche
width. (Remove screws holding trim to side of appliance and place
washers between prole and appliance and replace screws for exam-
ple)
Operate as follows:
Push the appliance into the installation niche
1
.
If the unit is to be installed inside a niche or within an enclosed
structure, it is not necessary to design a ventilation shaft at the back of
the niche as North American models come with a top ventilation cap
which accommodates sufcient ventilation even though it is behind
the overlay panel.
Ensure panels are mounted (BI Series) prior to pushing the appliance
all the way into the niche as the panel mounting procedure requires
additional height clearance than the niche provides.
If for some reason the top ventilation cap has been removed - a mini-
mum 5mm gap must be provided at the top / back of the cabinetry to
allow warm air to escape.
Check the levelling of the appliance, adjusting its feet and wheels
to correct it.
Using the screws provided, secure the appliance to the adjacent
cabinets through the holes on the prole side trims
2
.
To make this operation easier keep the door and the drawer open.
It may be necessary to hold the door at an approximate 70 degree an-
gle to get the easiest access on the hinge side prole with a screwdri-
ver.
Install the prole trim covers: mate with the face of the appliance
and the top of the niche then slide laterally over the prole trims. It will
be necessary to press rmly or use a block and mallet to completely
lock the trims into place until a ‘click’ is heard.
Take care not to damage the soft aluminum trims. Ensure that the full
installation is satisfactory prior to installing the prole trim covers as it is
very difcult to remove them without damaging them after installation
3
.
Built-in installation single appliance
Built-in installation of two or more appliances
Note: top ventilation caps not shown in illustrations
Appliance Wall
or
furniture
Wall
or
furniture
A Connecting element B Alluminium frame
Side proles mounting
Installation in cabinet of this height requires that the back of the cabinet de ventilated through the top. Otherwise,
an additional 2 inches of cabinet height is required for adequate ventilation. Height of custom side panel can be
higher as necessary.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Bertazzoni REF30PIXL Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues