Maytag MDB7751AWW Le manuel du propriétaire

Marque: Maytag

Modèle: MDB7751AWW

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

MA A(;

MDB-8

ii::i 8

Operating Tips ! ! !i ! !.i ! ii ii13 Troubleshooting ......... 9-10

Dishwasher Use ............ 5 Guide d'utilisation

et d'entretien .............. 12

Gui_ de uso y cuidado ...... 24

Part No. 6 920187 A www.maytag.com _2005 Maytag Appliances Sales Co.

Safety

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

tile dishwasher.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Important Safety Instructions

Products with a _ label [lave been listed with

Underwriter's Laboratories, Inc. - those with a CSA tag [lave

been listed with Canadian Standards Association.

Nevertheless, as with any other equipment using electricity

and moving parts, there is a potential hazard.

1. Read all instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before

attempting to service.

4. To avoid electrical shock hazard, the sides and back

must be enclosed and the front panels must be attached

before electrical power is applied to the dishwasher.

Refer to the installation instructions for proper grounding

procedures.

5. Connect to a properly rated, protected and sized power

supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play

in, with, or around this dishwasher.

Z To reduce the risk of injury when loading items to be

washed, sharp or pointed items should be located with the

handles up. Also, load sharp items so they are not likely to

damage the door seal.

8. Do not touch the heating element on the bottom of the

tub during or at the completion of a cycle. It will be hot.

9. Use only detergents and rinse additives designed for a

residential automatic dishwasher. Never use soap,

laundry detergent, or hand washing detergent in your

dishwasher. Keep these products out of reach of

children.

10. De not sit, stand on or abuse the door or dish racks of

the dishwasher.

11. Under certain conditions, hydrogen gas may be produced

in a [lot water system that has not been used for two

weeks or more. Hydrogen gas is explosive. If the [lot

water system has not been used for such a period, turn

on all hot water faucets and let the water flow from each

for several minutes. Thiswill release any accumulated

hydrogen gas. As the gas is flammable, do not smoke or

use an open flame during this process.

12. Do not wash plastic items unless marked "dishwasher

safe" or the equivalent. For plastic items not so marked,

check the manufacturer's recommendations.

13. Do not tamper with controls.

14. To prevent accidental child entrapment and suffocation

risks, always remove the door to the washing

compartment when removing an old dishwasher from

service or discarding it.

15. Use caution when unloading the dishwasher. Dishes will

be hot if unloaded shortly after a cycle has completed.

16. Certified residential dishwashers are not intended for

licensed food establishments.

1Z To avoid water, mold or mildew damage to your home,

inlet and drain [lose connections should be checked

periodically for leaks.

Save These Instructions

for Future Reference

WhatCanandCannotBeWashed

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

Aluminum Yes, except anodized. High water temperature and detergents may affect finish.

Cast Iron No Seasoning will be removed, and iron will rust.

China/Stoneware Yes, except antique or Always check manufacturer's recommendation before washing.

hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold

leaf may discolor.

Crystal Yes, except antique or Always check manufacturer's recommendation before washing.

delicate crystal. Some types of leaded crystal may etch with repeated washings.

Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.

Glass Yes A specialty glass called milk glass can yellow with repeated

dishwasher washing.

Gold-Plated No Will discolor.

Flatware

Pewter, Tin No

Plastics Yes, top rack, except Always check manufacturer's recommendation before washing.

disposable plastic Plastics vary in their capacity to withstand high water

items, temperatures and detergents. Disposable plastic items are not

dishwasher safe for this reason.

Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing

immediately. Prolonged contact with foods containing salt,

vinegar, milk products or juice could damage finish.

Sterling Silver or

Silverplate

No, if has commercial

"darkening".

Always check manufacturer's recommendation before washing.

Run a Rinse Only cycle (select models) if not washing

immediately. Prolonged contact with food containing salt, acid or

sulfide (eggs, mayonnaise and seafood) could damage finish.

Commercial "darkening" may be removed by detergent.

Wooden Items No Wood may warp, crack or discolor.

OperutingTips

Before You Start

• Don't prerinse. Simply scrape off any bones or

large food particles.

• If connected to a food waste disposer, make certain

the disposer is empty before starting the

dishwasher.

• Scrape off tomato-based food soils (see page 8).

• Remove certain foods such as mustard,

mayonnaise, lemon juice, vinegar, salt or dressings

from stainless steel flatware as soon as possible.

These foods may cause rusting and pitting if allowed

to remain in contact with the surface for an extended

period of time.

Starting the Dishwasher

1. After loading the dishwasher and adding detergent,

select the desired cycle by pressing the Cycle

Select pad until the light next to the desired cycle

is illuminated. Choose the desired options by

pressing the pads. The indicator lights for the

selected cycle and options will illuminate. To cancel

an option press the pad again.

2. To start a cycle, close the door until it latches then

press the START/CANCEL pad once. After a

pause, the fill will begin. The display countdown

(select models) will flash until START/CANCEL is

pressed.

J ote: If START/CANCEL is not pressed within 30

seconds of choosing your cycle, the dishwasher will

turn off.

The dishwasher remembers your last cycle so you

do not have to reset the cycle each time. To start

the dishwasher using the same cycle and options

selected on the previous wash, just press the

START/CANCEL pad.

3. To cancel a running cycle, press the

START/CANCEL pad once. The dishwasher will

drain, then shut off. To turn the dishwasher off

without draining, press the START/CANCEL pad

twice. To prevent unplanned cycle or option

changes, these selections are "locked in" after 1

minute.

Note: If the cycle select pad is pressed after the

controls have been "locked in", the light beside the

selected cycle will flash three times.

Adding a Forgotten Item

For best cleaning, the forgotten item should be added

early in the cycle.

1. Grasp door handle and unlatch door without

opening completely. All lights will flash to indicate

that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

/4. Close and latch the door. Lights will stop flashing

when the door is properly shut. After a slight delay,

the cycle resumes automatically at the point of

interruption.

Notes:

• If the door is opened during a running cycle,

there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

• Extended interruption of the wash cycle is not

recommended.

General Recommendations

(Rack features vary by model)

• Items can be centered behind a single tine or loaded

at an angle to maximize space.

• Avoid blocking or preventing the spray arms from

spinning freely. Do not allow items to extend beyond

the racks.

• Face soiled surfaces toward the center of the

dishwasher.

For best dishwashing results follow these guidelines to

determine the best arrangement for your items.

10 Place Setting Load

(Rack features vary by model)

3 saucers are

loadedonthe

rackunderthe

Stack-RackTM

Shelf

(select

models)

Upper Rack Lower Rack

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates,

bowls, pans, long-handled utensils etc. can be loaded

in this rack. Do not load glasses over the tines.

The Stack-Rack TM

(select models) on the

right side of the upper

rack folds up or down

for loading flexibility.

Fold it down to hold

long-handled knives,

spatulas and spoons or short items like cups or juice

glasses. Fold it up for taller items like glasses, bowls,

plates, etc.

The edge of the

Stack-Rack TM(select

models) is designed

to hold stemware in

place. Taller stemware

will fit better on the

right side as the

upper rack is deeper

on this side.

Lower Rack

A variety of items such as dinner plates, mixing bowls,

pots and pans and baking dishes can be loaded in this

rack.

Wider items can be placed along the left side and

back of this rack.

Utensil Basket

Removable Standard Utensil Basket

[style may vary]

For best cleaning results, prevent

items from nesting together by

placing some items in the basket

with handles up and some with

handles down. On slotted covers,

load knives handles up and

spoons and forks handles down.

Be sure that thin, finely pointed items do not extend

through the basket. This could block the lower wash

arm.

Auxiliary Basket [select models)

Use this supplemental basket in

the upper or lower rack for

loading miscellaneous items and

utensils. This is also a safe place

to load sharp knives and pointed

items.

Removing the Upper Rack

The rack can be removed when tall or oversized items

need to be loaded into the lower rack. Unload the

rack before removing it from the dishwasher.

To remove rack with tab-lock rack stops:

1. Roll the rack ½to _ of the way out.

2. Locate the rack stops at the end of each track.

Squeeze the tab in the middle of the rack stop and

pull the rack stop straight out. Take care to support

the rack while removing the rack stops.

3. Roll the rack all the

way out of the track

and remove from

the dishwasher.

To replace:

1. Replace the

dishwasher rack by

guiding the wheels

into the tracks.

Style may vary by model

Tab Lock

Rack Stop

2. Push each rack stop squarely into the end of the

track until the catch pops into the small hole on the

side of the track.

Important:

The dishwasher will not

operate correctly if the

wash arm is not aligned

with one of the water

inlet holes on back wall

of the dishwasher.

DishwasherUse

Hot Water

For optimal cleaning and drying results, hot water

is necessary. The incoming water temperature

should be 120 ° F [49 ° C) to properly activate the

detergent and melt greasy food soils.

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run

into a glass in the sink. Place a candy thermometer in

the glass and check the temperature once it has

stopped rising.

Detergent

Use a detergent designed specifically for use in an

automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink).

Recommended Amount

Too little detergent results in poor cleaning, hard water

filming/spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness.

Suds can cause the dishwasher to overflow. Measure

the detergent carefully and use only detergents

designed for use in a dishwasher. Less detergent is

needed in soft water. Try another brand of detergent if

sudsing continues.

The amount of detergent to use is determined by the

hardness of the water and soil level of the load. Refer

to the following chart for detergent usage

recommendations.

Light Soil 2 tsp 6 tsp

Soft (0-4 gpg) Normal Soil 4 tsp 6 tsp

Heavy Soil 4 tsp 7 tsp

Medium (5-9 gpg) Light Soil 4 tsp 6 tsp

Normal Soil 4 tsp 6 tsp

Heavy Soil 5 tsp 7 tsp

Hard (10-12 gpg) All Levels 5 tsp 8 tsp

*Your local water utility or state university extension service can tell

you the degree of water hardness in your area.

In extremely hard water conditions (13 grains per

gallon or more*), it is difficult to achieve good

results with any dishwasher. A mechanical water

softener may be necessary to improve water

quality, detergent effectiveness, and protect the

dishwasher parts from the damage that hard

water can cause.

Add recommended amount of detergent to each cup

as shown and close the detergent lid.

Do not use detergent with the Rinse Only (select

models) cycle. Leave the detergent lid open when

running Rinse Only (select models).

Rinse Aid

Regular use of a rinse aid improves drying,

reduces spotting and filming, and reduces

moisture left on the dishwasher interior.

An automatic rinse aid dispenser is located next to the

detergent cup.

The window next to the dispenser cap indicates when

the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser monthly.

To add rinse aid to the

dispenser, turn the cap

counterclockwise to open.

Remove the cap and pour

liquid rinse aid into the

opening. The amount of

rinse aid dispensed during

the cycle is adjustable by moving the lever inside the

reservoir area. For most water conditions use the

manufacturer recommended setting of "2". Adjust it up to

the "MAX" setting for hard water. Set the lever anywhere

between these amounts as needed to get the best results.

Replace the cap and turn it clockwise to close.

Cvcles,OptionsandLights

Cycles

Choose tile cycle that best describes your dishload by pressing the cycle select pad. (See page 3, Operating Tips, for how

to begin the cycle).

Heavy Longcycle for heavy food soils. 132" 2 washes/3 rinses

Medium cycle for average food soils.

Normal The turbidity sensor is active with this 97-117" 1-2 washes**/1-2 rinses**

cycle.

Light Short cycle for light food soils. 82* 1wash/2 rinses

Rinse Only Rinses dishes being held until there 9 1 rinse

(select models) is a full load.

Includes approximately 30 minutes of dry time.

**Number of fills will vary depending on the soil level of each load.

Notes:

• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

• Only the following certified cycles have been designed to meet NSF requirements ([NSF/ANSI 184 Residential

Dishwasher) for sanitization: Heavy, Normal and Light cycles.

Options

In addition to choosing a cycle, choose as many available options as are needed for your dishload.

Hi Temp Wash provides additional heat during the wash portion of the cycle, All cycles

Hi femp Wash which ensures proper water temperature for better cleaning and drying results. (except Rinse Only

It also adds an additional rinse to the cycle which improves results in hard [select models])

water situations.

For enhanced drying results select this option. When Heated Dry is not

selected, towel drying of some items such as plastic and items with non-stick All cycles

Heated Dry surfaces may be necessary and more moisture may be noticed adhering (except Rinse Only

to the dishwasher interior. In models with plastic interiors, it is normal to [select models])

notice vapor escaping from the door vent as the heat dries your dishes. Vapor

will escape even if Heated Dry is not selected.

Delay Use to automatically start the cycle at a later time. See page 7 for instructions. All Cycles

Tough ScruhTM/ Select when washing loads with hard to remove soils. Depending on which All Cycles

Tough Scrub PlusTM cycle is being used, this option adds heat, water and or wash time to the wash

([select models) cycle.

Sanitize Sanitizes dishware. When cycle monitor recognizes that the proper conditions All Cycles

([select models) have been met, Sanitized light will activate at the end of the cycle. Sanitization

may not be achieved if there is an interruption of the cycle, power failure or if

the incoming water temperature is below 120° F [49° C].

START/CANCEL Starts and stops dishwasher. See page 3 under Operating lips: All Cycles

Operating the Dishwasher, for explanation.

Locks control touchpad to prevent unwanted use. See page 7for instructions. All CyclesControl Lock Option

([select models)

Cycles,OptionsandLights

Delay

The Delay option can be used to automatically start

the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced

energy costs if available in your area. This option is

also useful for conserving hot water at times of high

household usage (showers, laundry).

To set up a Delay:

1. Select the appropriate cycle and options for the

load. Close the door.

2. Press the Delay pad until the desired amount of

delay time is selected.

3. The Delay indicator and the count down display

(select models) will flash until the START/CANCEL

pad is pressed.

4. As soon as the START/CANCEL pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Delay indicator will remain lit

until the delay time has counted down.

5. The cycle will automatically start as soon as the

delay time expires.

Note: If 30 seconds elapse between setting the

cycle and options and pressing the

START/CANCEL pad, the dishwasher will turn off.

To cancel a Delay:

When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will

start or resume immediately.

To cancel a Delay and the cycle:

• Press START/CANCEL once to drain and turn off

the dishwasher.

• Press START/CANCEL twice to turn dishwasher off

without draining.

Control Lock

Option (select models)

The control touchpads can be locked to prevent

unwanted use. If this feature is activated between

cycles, the dishwasher cannot be operated until the

controls are unlocked. If desired, the controls can be

locked after a cycle or Delay has started.

Setting the Control Lock:

1. Press the Heated Dry pad for three seconds.

2. An indicator light next to the lock graphic will

illuminate when the controls are locked.

To Cancel:

1. Press the Heated Dry pad for three seconds.

2. The indicator light will go off.

Notes:

• If a cycle or option pad is pressed after the

controls have been locked, the indicator light next

to the lock graphic will flash five times. On select

models with a countdown display, the display will

flash an "L" simultaneously with the lock

indicator.

• This option does not lock the door, only the

dishwasher controls.

Lights/Display (select models)

N ....

Clean Light Illuminatesatthe end of the cycleand remainslit until the doorhasbeenopenfor 30 secondscontinuously.

Wash/Dry Light Illuminatesduringall rinse,wash and dryportionsof the cycle.

Sanitized Light Illuminatesatthe end of the cyclewhenconditionshavebeenmet to achievesanitization. Thelight will

(select models) remainlit until the door hasbeen openfor 30secondscontinuously.

Notes:

• When Sanitize is selected, cycles are monitored to assure sanitization. The Sanitized light will not activate if sanitization

requirements are not met. This could happen if the cycle is interrupted, power failure occurs or incoming water

temperature is below 120° F(49° F).

• The Clean and Sanitized indicator lights (select models) will not relight after a power failure until after the next cycle is run.

CareandCleaning

General Recommendations

• The dishwasher interior is normally self-cleaning.

Periodically check the bottom of the dishwasher tub

to see if any large particles remain.

• Wipe the edge of the inner door liner to remove any

food soil splashes which occurred during loading.

• When cleaning stainless steel, always wipe with the

grain. Never use products containing chlorine bleach

or citric acid.

• The color from some tomato-based food soils may

occasionally adhere to various components of the

dishwasher interior, causing temporary discoloration.

To minimize this:

• Remove excess tomato-based food soils from dishes,

before loading.

• Run the Heavy cycle when washing loads containing

tomato-based food soils.

• Use a dishwasher detergent that contains chlorine to

better fight staining.

!!i!ii !!i!i !i! !

Standard Exterior Light to moderate Soft damp cloth and liquid spray cleaner.

Daily cleaning and light soil

Stainless Steel

Exterior

(select models)

Moderate to heavy soil

Streaks or fingerprints/restore shine

Discoloration

Interior Light to moderate

Discoloration, or tomato-based stain

*Brand names are trademarks of the respective manufacturer.

**Call 1-877-232-6771 U.S.or 1-800-688-8408 Canada to order.

Do Not use abrasive powders or cleaning pads.

Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula/409 Glass and Surface Cleaner*, or

similar multi-surface cleaner.

• Do Not use products containing chlorine

bleach or citric acid.

Follow with rinse and dry.

Soft cloth or damp sponge and Bon Ami*.

Follow with rinse and dry.

Soft cloth and Stainless Steel Magic Spray**.

Soft cloth or damp sponge and Cameo Stainless

Steel Cleaner*. Rinse immediately and dry.

Soft cloth or damp sponge.

Switch dishwasher detergent to chlorine-based

product.

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher

detergent or baking soda and select the Normal cycle.

Allow the dishwasher to complete the cycle. Then turn

the water supply off and drain the dishwasher. To drain,

press the START/CANCEL pad once to activate the

dishwasher. Press START/CANCEL again to activate

the drain. Operate the drain twice to ensure most of the

water is removed. Last, disconnect the electrical supply

and prop open the door.

When turning the water supply to the home off, the

water shut off at the dishwasher must be turned off also.

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.

Dishwasher will not fill • Press the START/CANCEL pad to start the dishwasher.

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home's circuit breaker or fuse box.

• Check inlet hose for a kink.

• Check water valve inlet for sediment and clean if necessary.

Dishwasher will not drain/ • If hooked up to a food waste disposer, be sure the knock-out is removed from the

water in tub bottom disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home's circuit breaker or fuse box.

• Check that the cycle is completed.

Dishwasher adds water at • This is normal. The sensor (select models) in the pump must stay submerged so a

end of cycle short fill of water is added after the cycle's last drain.

• Check that the cycle is completed.

Detergent cup is not empty

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place.

Dishwasher seems noisy • A water valve hiss during fill is normal.

• Water circulation sounds are normal.

• A thumping sound may be a wash arm bumping an item that is extending beyond the

racks. Readjust load to avoid obstructing wash arm.

• Chopping or grinding sounds may be heard as the internal chopper blade chops hard

items like fruit seeds, nuts, etc.

• Humming during the drain is normal.

• A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of the cycle. This is normal.

• Proper installation affects the noise level.

Cycle takes too long • Sanitize has been selected and the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49° C).

Dishwasher has an odor • Run dishes being held in the dishwasher through a Rinse Only cycle.

• Many dishwashers have a "new" smell when first installed. This will dissipate with use.

• Dishwasher may not be draining properly. (See"Dishwasher Will Not Drain" section.)

• Fora strong odor, place baking soda in both sides of the detergent cup. Select Light

cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle by

unlatching the door and let it stand overnight. Restart the dishwasher by latching the

door and allow it to complete the cycle. Another alternative is to use a dishwasher

cleaning product such as Jet-Dry Dishwasher Cleaner+.

Dishwasher leaks • Check that the dishwasher is level. (Refer to the Installation Instructions.)

• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use

only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Try another brand of detergent if sudsing continues.

• Follow directions closely on how to add a forgotten item (pg. 3).

• Toavoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

Indicator lights flashing • The countdown display (select models) flashes after a cycle is selected until the

START/CANCEL pad is pressed.

• The countdown display (select models) and the delay indicator flash after a delay is

selected until the START/CANCEL pad is pressed.

• All active display indicators flash if the door is opened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after

cycle "lock-in".

• The lock indicator flashes and the countdown display (selected models) flashes an "L"

if a pad is pressed while the control lock is enabled.

Cont.

*Brand names are trademarks of the respective manufacturer. 9

iiiiil i iii ii}DilOiii!ii!i}!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i}}il,iii }

Display time drops • This isnormal when the Auto Clean (:selectmodels} or Normal cycle is selected and the

dishwasher decides to skip or add a drain and refill.

or increases

(:select models:)

Glasses are cloudy/ • Select Hi Temp option.

• Check water temperature. Incoming water should be 120° F(:49° C}.

spotted • Always use a rinse aid.

• Confirm that the cloudiness isremovable by soaking the item in white vinegar for

approximately 5 minutes. If removed, the problem isdue to hard water. Adjust detergent

amount being used to match water hardness (pg. 5}. Be sure detergent isfresh, stored

properly and is a high quality brand.

• If cloudiness is not removable, it is etching. Thisisan erosion of the surface of the

glassware and can be caused by water that istoo hot, from using too much detergent or by

prewashing. Detergent needs food soil to act upon. Ifetching has occurred, the glassware is

permanently damaged. Toprevent further etching, adjust the detergent amount to match

the water hardness, stop prewashing, and use water heating options only when incoming

water temperature isbelow 120° F (:49° C}.

Food soil remains • Check water temperature. Incomingwater should be 120° F (:49° C}.

• Run hot water at the sink before starting the dishwasher.

on dishes

• Check water hardness and adjust detergent amount accordingly (pg. 5}.

• Use fresh detergent stored in a cool dry place.

• Select proper cycle for the soil level (:pg.6}.

• Select proper options, Hi Temp Wash, Tough ScrubTMorTough Scrub PlusM (:selectmodels}.

• Make sure the upper rack wash arm connector iscorrectly aligned in one of the water inlet

holes (:pg.4}.

• Load items so they do not block the wash arms (:pgs.3-4}.

• Load the utensil basket with knife handles up and spoon and fork handles down.

• Do not place glasses over tines.

• Before loading,scrape off burnt on foods and wipe the starchy film from utensils used with

pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.

items washed in the • Aluminum utensils or pans can leave marks when they rub against other items.Leave a

dishwasher or the slight space between items.

• Iron deposits in the water can leave a yellow, brown or orange film on dishes or the

dishwasher tub itself dishwasher tub. A rust filter may be needed. Check with a water treatment company.

are stained/discolored • Separate silver or silver-plated silverware from stainless steel. These metals can be

damaged by contact with each other during washing.

• Color from tomato sauces may adhere to the interior parts of the dishwasher (:pg.8}. If light

staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher

detergent that contains chlorine to better fight staining.

• Certain dishwasher detergents may stain silver. Tryanother brand of detergent.

Items not properly • Be sure Heated Dry is selected.

dried/moisture is • Water droplets may form on the inner door as part of the drying process.

present on the • Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid* regularly, to

dishwasher interior improve drying. Turn the rinse aid selector toward the MAX setting.

• Check water temperature. Incoming water should be 120° F (:49° C}.

after the dry cycle • Select Sanitize option.

• Increase detergent amount to match water hardness (:pg.5}.

• Load properly. (pgs. 3-4}

• Plastic and items with non-stick surfaces are difficult to dry because they have a porous

surface which tends to collect water droplets. Towel drying may be necessary.

• Glasses and cups with concave bottoms hold water and require towel drying. Locate these

items on the more slanted side of the rack for improved results.

Dishware is chipped • Load dishes according to instructions so they do not strike each other (pgs. 3-4}.

• Washing fine antique china/crystal in the dishwasher is not recommended.

• Do not load glasses over the tines.

• Do not overload.

Sanitized light does not • Sanitize was not selected.

illuminate at the end of • Sanitization can only be achieved with the Heavy, Normal or Light cycles.

the cycle [select • Sanitization may not be achieved if there is an interruption of the cycle, power failure or if

models:) incoming water temperature is below 120° F (:49° C}.

Dishwasher door will • Be sure adjustable racks (:select models} are properly adjusted to upper or lower position

not close (:pg.4).

*Brand names are trademarks of the respective manufacturer.

Wurrum¥u,d Service

CUSTOMER'S SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. IMPLIED

WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESSFOR

A PARTICULAR PURPOSE,ARE LIMITED

TO ONE YEAR ORTHE SHORTEST

PERIODALLOWED BY LAW. MAYTAG

CORPORATION SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATESAND

PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE

DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS,SO

THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TOYOU. THIS

WARRANTY GIVESYOU SPECIFICLEGAL

RIGHTSAND YOU MAY ALSO HAVE

OTHER RIGHTS,WHICH VARY STATETO

STATEOR PROVINCE TO PROVINCE.

What is Not Covered By These Warranties

1. Conditions and damages resulting from any of tile following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents, unreasonable use, or acts of God.

d. Incorrect electric current, voltage, electrical and/or gas supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered,

or cannot be readily determined.

3. Light bulbs, water filters and air filters.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors. For products requiring ventilation, rigid metal

ducting must be used.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to and from the servicer.

6. Any food loss due to refrigerator or freezer product failures.

Z Expenses for travel and transportation for product service in remote locations.

8. Outside of the United States and Canada this warranty does not apply.

Contact your dealer to determine if another warranty applies.

9. Consequential or incidental damages sustained by any person as a result of

any breach of these warranties. Some states do not allow the exclusion or

limitation of consequential or incidental damages, so the above exclusion may

not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the

dealer from whom your appliance was purchased or call Maytag Services, LLC,

Customer Assistance at 1-800-688-9900 USA and 1-800-688-2002 Canadato

locate an authorized servicer.

• Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY

for further information on owner's responsibilities for warranty service.

• If the dealer or service company cannot resolve tile problem, write to Maytag

Services, LLC,Attn: CAIR_ Center, EO. Box 2370,Cleveland,TN 37320-2370,or call

1-800-688-9900 USA and 1-800-688-2002 Canada. U.S.customers using

TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

• User's guides, service manuals and parts information are available from Maytag

Services, LLC,Customer Assistance.

Notes: When writing or calling about a service problem, please include:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or servicer;

d. A clear description of the problem you are [laving;

e. Proof of purchase (sales receipt).

NIAYFAG

MDB-8

Conseils d'utUisation ....... 15

Chargement ........... 15-16

Utilisation du

lave-vaisselle .............. 17

Entretien et nettoyage ...... 20

D6pannage ............ 21-22

Garantie et service ......... 23

Guilt de uso y cuidado ...... 24

Securtt6

Ce que vous devez savoir sur

les instructions de s curtid

Lesinstructions de s_curite importantes et les avertissements

paraissant dans ce guide ne sont pas destines _ couvrir toutes

lessituations et conditions eventuelles qui peuvent se

presenter.IIfaut faire preuve de bon sens et de prudence Iors

de [installation, de I'entretien ou de I'utilisation de I'appareil.

Preneztoujours contact le fabricant, au sujet de problemes

ou conditions que vous ne comprenez pas.

Reconnaissez les tiquettes, phrases

ou symboles sur la s curitb

Instructions de sbcuritb importantes

Lesproduits portant une etiquette (_ ont ete homologues par

Underwriter's Laboratories,Inc.- ceux portant une etiquette

CSAont ete homologues par la CanadianStandards Association

(CSA). Neanmoins,comme pour tout autre equipement utilisant

I'electriciteet des pieces mobiles, il y a un danger potentiel.

1. Lire la totalite des instructions avant d'utiliser le lave-

vaisselle.

2. Utiliser le lave-vaisselle uniquement pour les

applications.

3. Debrancher le lave-vaisselle avant tout entretien.

4. Pour eviter tout risque de choc electrique, les c6tes et

I'arriere doivent etre fermes et le panneau avant doit

etre fixe avant de brancher le lave-vaisselle. Se

reporter aux instructions d'installation pour les

methodes correctes de mise _ la terre.

5. Brancher le lave-vaisselle _ un circuit electrique

correctement protege, d'une puissance nominale

appropriee et avec fils de calibre adequat.

6. II ne faut jamais laisser les enfants utiliser ou jouer

dans, avec ou autour du lave-vaisselle.

7 Pour reduire le risque de blessure Iors du chargement

du lave-vaisselle, il faut placer les articles pointus ou

aiguises avec le manche vers le dessus. De meme,

Ioger les articles pointus pour qu'ils n'endommagent

pas le joint de la porte.

8. Ne pas toucher _ I'element chauffant au bas de la

cuve durant ou _ la fin d'un cycle car il est chaud.

9. N'utiliser que des detergents et des agents de rin_sage

con_us pour un lave-vaisselle residentiel automatique.

Ne jamais utiliser de savon, de detergent lessiviel ou

de detergent de lavage _ la main dans votre lave-

vaisselle. Garder ces produits hors de portee des

enfants.

10. Ne pas s'asseoir, se mettre debout ou maltraiter la

porte ou les paniers du lave-vaisselle.

11. Sous certaines conditions, de I'hydrogene peut se former

dans un systemed'eau chaude qui n'a pasete utilise

pendant deux semaines ou plus. L'hydrog_ne est un

gaz explos_ Si le systeme d'eau chaude n'a pas ete

utilise pendant une telle periode,ouvrir tousles robinets

d'eau chaude et laissercouler I'eaupendant plusieurs

minutes. Ceci diminuera [accumulation d'hydrogene.

Comme il s'agit d'un gaz inflammable, ne pas fumer ou

utiliser de flamme vive durant cette operation.

12. Ne pas laver d'articles en plastique ne portant pas

I'indication _<lavable en lave-vaisselle >>.Pour des

articles en plastique sans indication, verifier les

recommandations du fabricant.

13. Ne pas circonvenir les commandes.

14. Pour eviter tout risque d'enfermement et/ou de

suffocation accidentelle d'un enfant, toujours enlever

la porte du compartiment de lavage Iorsque I'on

enleve un ancien lave-vaisselle ou qu'on le jette.

15. Faire preuve de prudence en dechargeant le lave-

vaisselle. La vaisselle peut etre chaude si elle est

dechargee peu de temps apres la fin d'un cycle.

16. Leslave-vaissellea usage residentiel certifie ne sont pas

congus pour les etablissements alimentaires

homologues.

17 Poureviter que I'eau ou la moisissure ne deteriore votre

habitation, verifiez regulierement les raccordements

d'arrivee d'eau et lestuyaux d'evacuation pour

d'eventuelles fuites.

Conserver ces instructions

Articlesluvublesounonenluve-vuisselle

La plupart des articles de table et de cuisson ainsi que les couverts peuvent 6tre laves en securite dans le lave-vaisselle. Verifier avec le fabricant.

Aluminiam Oui, sauf raluminium anodis& De hautes temperatures et les detergents peuvent attaquer la finition.

Fonte Non L'appret serait enleve et le fer rouillerait.

Oui, sauf les pisces Toujours verifier les recommandations du fabricant avant le lavage. Les

Porcelaine/Gr_s d'antiquite ou peintes _ la porcelaines fines, les motifs peints _ la main ou sur le vernis peuvent s'estomper.

main. Les feuilles d'or peuvent se decolorer.

Oui, sauf les pieces Toujours v@ifier les recommandations du fabricant avant le lavage. Certains

Cristal d'antiquite et le cristal types de cristal au plomb peuvent se corroder apr_s des lavages r@etes.

delicat.

Filtres Non recommandes. Peuvent laisser un depSt crasseux ou des taches _ I'int@ieur du lave-vaisselle.

Verre Oui Un verre special appele <_verre laiteux >}peut jaunir par suite de lavages repetes

au lave-vaisselle.

Couverts plaques or Non Se decolorent.

_tain, fer blanc Non

Oui, sur panier sup@ieur Toujours v@ifier les recommandations du fabricant avant le lavage. La capacite

Plastiques sauf les articles en plastique des plastiques _ resister aux hautes temperatures et aux detergents peut varier.

jeter. Les articles en plastique jetable ne sont pas lavables en lave-vaisselle.

Oui Si ces articles ne sont pas laves immediatement, lancer un cycle Rinse Only

Acier inoxydable (Ringage seulement] (certains modules]. Le contact prolonge avec la nourriture

contenant du sel, du vinaigre, des produits laitiers ou du jus peut endommager la

finition.

Non, s'il a subi un traitement Toujours verifier les recommandations du fabricant avant le lavage. Si ces articles

Argenterie ou de <_noircissement >}. ne sont pas laves immediatement, lancer un cycle Rinse Only (certains modeles).

argent sterling Le contact prolonge avec la nourriture contenant du sel, de I'acide ou des

sulfures (oeufs, mayonnaise ou fruits de mer) peut endommager la finition. Le

_ noircissement >_commercial peut etre enleve par le detergent.

Articles en bois Non Le bois peut se ddormer, se fissurer ou se decolorer.

Conseilsd'udlisadon

Avant de commencer

• Ne pas pr_rincer. II suffit de jeter os et gros

morceaux de nourriture.

• Si le lave-vaisselle est raccord6 a un broyeur

dCchets, veiller & ce flue celui-ci soil vide avant

de mettre le lave-vaisselle en marche.

• Gratter los laches tenaces laiss_es par los

aliments _ base de tomate (voir page 20).

• Eliminer certains aliments (tels que moutarde,

mayonnaise, jus de citron, vinaigre, sel et

vinaigrettes) des articles en acier inoxydable

aussi rapidement que possible. Cos aliments

peuvent provoquer de la rouille et du piquage s'ils

restent en contact prolong6 avec la surface.

Utilisation du lave-vaisselle

1. Apres avoir charg6 le lave-vaisselle et ajout6 du

detergent, choisir le cycle dCsir6 en appuyant sur la

touche correspondante, jusqu'a ce que le tCmoin

lumineux _ c0t6 du cycle dCsirC, s'allume. Choisir

los options dCsirCes en appuyant sur los touches.

Les voyants de signalisation pour le cycle choisi et

los options lumineux. Pour annuler une option

appuie le coussin encore.

2. Pour dCmarrer un cycle, former la porte jusqu'a ce

qu'elle se verrouille, puis appuyer une lois sur la

touche START/CANCEL (Mise en Marche/

Annulation). /_ la suite d'une pause, le remplissage

commence. Le dCcompte de I'afficheur (certains

modeles) clignote jusqu'a ce que I'on appuie sur

START/CAN CE L

Remarque : si I'on n'appuie pas sur la touche

START/CANCEL dans los 30 secondes suivant la

sClection du cycle, le lave-vaisselle s'arrete.

Le lave-vaisselle se souvient du dernier cycle choisi.

II n'est donc pas nCcessaire de reprogrammer le

cycle a chaque lois. Pour mettre en marche le lave-

vaisselle avec le memo cycle et los memos options

que ceux choisis Iors du lavage prCcCdent, il suffit

d'appuyer sur la touche START/CANCEL

3. Pour annuler un cycle en cours de fonctionnement,

appuyer une lois sur la touche START/CANCEL Le

lave-vaisselle procede a une vidange puis s'arrete.

Pour arreter le lave-vaisselle sans qu'il ne commence

une vidange, appuyer deux lois sur la touche

START/CANCEL Pour empecher des changements

non prCvus de cycle ou d'option, il n'est plus

possible de changer cos sClections apres 1 minute.

Remarque : si ron appuie sur la touche de cycle

select apres le <{verrouillage >>des commandos, le

tCmoin lumineux situ6 _ cote du cycle sClectionn6

clignote trois lois.

Ajout d'un article oublie

Pour de meilleurs rCsultats de nettoyage, I'article oubli6

devra etre ajout6 au dCbut du cycle.

1. Saisir la poignCe de porte et dCverrouiller la porte

sans I'ouvrir completement. Tous los tCmoins lumineux

clignotent pour indiquer que le cycle est interrompu.

2. Attendre I'arret de la circulation d'eau.

3. Ouvrir la porte et ajouter I'article.

4. Fermer la porte et la verrouiller. Les tCmoins

lumineux cessent de clignoter Iorsque la porte est

correctement fermCe. Apres un court instant, le cycle

reprend automatiquement au point ca il s'est arretC.

Remarques :

• Si la porte est ouverte pendant le fonctionnement

d'un cycle, il pout y avoir jusqu'_ 30 secondes

d'attente avant que I'appareil nese remette en

marche une lois la porte fermCe.

• II n'est pas recommand6 d'interrompre le cycle de

lavage pendant une pCriode prolongCe.

Recommandations d'ordre

gdndral (Les caract_ristiques des paniers

varient selon le modble)

• Los articles peuvent _tre centrCs derriere une tige de

retenue ou charges en biais pour tirer le meilleur

parti possible de I'espace.

• I_viter de bloquer los bras gicleurs. Ne rien laisser

dCpasser des paniers.

• Tourner los surfaces souillCes vers le centre du lave-

vaisselle.

Pour obtenir los meilleurs rCsultats de lavage, observer

los directives suivantes pour determiner la disposition

qui convient le mieux aux articles _ laver.

10 Couverts (Loscaracteristiquesdes

paniers varient solon le module)

3 assiettes

pain et beurre

sont plac_es

sur le paniei

SOUS

I'_tag_re

Stack-Rack ic

(certains

modules)

Partier inf_rieur

Panier sup_rieur

Churgement

Panier supbrieur

II peut recevoir verres, tasses, articles en plastique

leger, assiettes, bols, casseroles, ustensiles a long

manche, etc. Ne pas placer les verres sur les tiges

de retenue.

L'etagere Stack-Rack Mc.

(certains modeles) _ la

droite du panier

superieur, se releve ou

s'abaisse pour plus de

souplesse de

chargement. L'abaisser

pour retenir les couteaux, les spatules et les cuilleres

long manche ou les articles courts coming les tasses et

les verres a jus. La relever pour Ioger les grands

articles coming les verres, les bols, les assiettes, etc.

Le bord de I'etagere

Stack-Rack Mc(certains

modeles) est con(_u pour

retenir les verres _ pied

en place. II est preferable

de placer les verres dont

le pied est plus long

droite, car le panier

superieur est plus profond a cet endroit.

Panier infbrieur

II peut recevoir une variete d'articles, des assiettes

diner, des bols melangeurs, des casseroles et des plats.

Des articles plus larges peuvent etre places le long du

cote gauche et _ I'arriere de ce panier.

Panier pour ustensiles

Panier _ Ustensiles Standard, Amovible

(le style peut varier)

Pour obtenir de meilleurs resultats de lavage, empecher

les articles de s'emboiter les uns

dans les autres en mettant

certains ustensiles dans le panier

avec les manches vers le haut et

certains avec les manches vers le

bas. Sur les modeles dont les

couvercles des paniers pour

ustensiles presentent des

ouvertures, ranger les couteaux

avec le manche vers le haut, et

les cuilleres et fourchettes avec le manche vers le bas.

S'assurer que les articles minces et pointus ne

depassent pas du panier. Sinon, ils risquent de bloquer

le bras inferieur de lavage.

Panier auxiliaire (certainsmodeles)

Utiliser ce panier supplementaire

dans le panier superieur ou

inferieur pour y charger des

articles et ustensiles divers.

Ce panier est egalement un

endroit s0r pour Ioger les

couteaux aff0tes et les articles

pointus.

Desmontaje de la rejilla superior

Le panier peut etre enleve pour placer des articles

hauts ou surdimensionnes dans le panier inferieur.

Decharger d'abord le panier avant de I'enlever.

Retirer un panier muni de buttes avec languette

de sdret_ :

1.Tirez le panier vers vous du '/__ '/_.

Reperez les

butees au

bout de chaque

guide. Appuyez

sur les

languettes de

s0rete situees

au centre des Le style peut varier

butees et retirez

les butees completement et tout

droit. Assurez-vous de soutenir le panier au

moment de retirer les butees.

BuLges

avec

languette

de serete

3. Remettez le panier completement et sortez-le du

lave-vaisselle.

R_installation :

1. Remettez le panier du lave-vaisselle en faisant

glisser les roulettes dans les guides.

2. Inserez chacune des butees au bout des guides

de fa(_on _ ce qu'elles penetrent dans les petits

trous situes sur les cotes des guides.

Importante :

L'appareil ne fonctionne

pas correctement si le

raccord du bras de lavage

du panier n'est pas align_

avec I'un des orifices

d'arriv_e d'eau & I'arribre.

Udlisadondulave-vaisselle

Eau chaude

Pour des r_sultats de nettoyage et de s_chage

optimaux, reau chaude est n_cessaire. La

temperature de I'eau d'arriv_e doit se trouver

entre 49 ° C [120 ° F) pour activer correctement le

d_tergent et faire fondre la salet_ et la graisse.

Pour verifier la temperature de I'eau _]son arrivee,

ouvrir le robinet d'eau chaude le plus proche du

lave-vaisselle et faire couler I'eau dans un verre place

dans I'evier. Placer un thermometre _ confiserie dans

le verre et verifier la temperature une lois qu'elle s'est

stabilisee.

Ddtergent

Utiliser un detergent con£u specifiquement pour etre

utilise dans un lave-vaisselle automatique. S'assurer

qu'il n'est pas perime et s'il est en poudre, le ranger

dans un endroit sec et frais (pas sous I_vier).

Quantit_ recommand_e

Une trop faible quantite de detergent entrafnerait de

faibles resultats de lavage, un depot et I'apparition de

taches dus a I'eau dure et un sechage inefficace. Une

trop grande quantite de detergent peut causer un

piquage et un aspect terne permanent.

La mousse peut faire deborder le lave-vaisselle. Dosez

soigneusement le detergent et n'utilisez que des

produits specialement con£us pour le lave-vaisselle. La

quantite de detergent doit etre reduite en presence

d'eau douce. Essayez une autre marque de detergent

si la quantite de mousse reste excessive.

La quantite de detergent _ utiliser est determinee par

la durete de I'eau et le niveau de salete de la vaisselle.

Se referer au tableau ci-dessous pour connaitre les

recommandations d'utilisation du detergent.

L6ger 2 cuill@es _ th6 6 cuill_res _ the

Douce 1:0-4 gpg) Normal 4 cuill@es _ th6 6 cuill_res _ the

Intense 4 cuill@es _ th6 7 cuill_res _ the

L6ger 4 cuill@es _ th6 6 cuill_res _ the

Moyenne (:5-9 gpg) Normal 4 cuill@es _ th6 6 cuill_res _ the

Intense 5 cuill@es _ th6 7 cuill_res _ the

Dare (:10-12 gpg) Tousles 5 cuill@es _ th6 8 cuill_res _ the

Niveaux

*Votre station locale d'approvisionnement en eau ou tout autre service

comp6tent de votre province, peut vous donner le degr6 de durete de

I'eau dans votre r6gion.

En cas d'eau extremement dure (13 grains par

gallon ou plus*), il est difficile d'atteindre de bons 17

r_sultats avec n'importe quel lave-vaisselle. Un

adoucisseur d'eau m_canique peut _tre

n_cessaire pour am_liorer la qualit_ de I'eau et

I'efficacit_ du d_tergent et prot_ger les pibces du

lave-vaisselle contre les dommages provoques

par I'eau dure.

Ajouter la quantite recommandee de detergent dans

chaque tasse comme il est illustre et fermer le

couvercle du compartiment.

Ne pas utiliser de detergent avec le cycle Rinse Only

(Rin£age seulement) (certains modeles). Laisser le

couvercle du distributeur de detergent ouvert Iors du

cycle Rinse Only (certains modeles).

Agentde rin£age

L'utilisation r_guli_re d'un agent de rin£age

am_liore le s_chage, r_duit les taches et les

d_p6ts de film ainsi que I'humidit_ & I'int_rieur du

lave-vaisselle.

Un distributeur automatique d'agent de rin£age se

trouve _ cote du godet de detergent.

Le hublot _ cote du capuchon du distributeur indique

quand il est necessaire de remplir le reservoir d'agent

de rin£age. Lorsque le niveau d'agent de rin£age se

trouve en dessous de I'indicateur et que le hublot est

presque transparent, il est temps de remplir le

distributeur. V_rifier le distributeur tous les mois.

Pour ajouter de I'agent de

rin£age dans le

distributeur, tourner le

capuchon vers la gauche RINSE

pour I'ouvrir. Enlever le

capuchon et verser I'agent

de rin£age dans I'ouverture.

La quantite d'agent de rin(;age distribuee au cours du

cycle peut etre reglee en depla(;ant le levier

I'interieur de la zone du reservoir. La plupart du temps,

utiliser le reglage {{2 >>,recommande par le fabricant.

Regler a la position {{ MAX _>pour une eau dure. Placer

le levier n'importe oa entre ces deux reperes pour

obtenir les meilleurs resultats. Remettre le capuchon et

le tourner vers la droite pour le fermer.

Cycles,optionsettemoinslumineux

Cycles

Choisir le cycle qui convient le mieux _ la vaisselle en appuyant sur la touche cycle select. (Voir page 15,Conseils

d'utilisation, pour la mani6re de dCbuter le cycle.)

Heavy [intense) Cycle long pour vaisselle tr_s sale. 132" 2 lavages/3 rin_.ages

Normal [Normal) Cycle moyen pour vaisselle normale-ment sale. 97-117" 1-2 lavages**/1-2 rin_.ages**

Le capteur de turbidit6 est actif avec ce cycle.

Light [Leger) Cycle court pour vaisselle peu sale. 82* 1 lavage/2 rin£ages

Rinse Only Rince la vaisselle en attente de prochaines 9 1 rin_.age

(Ringage seulementD charges.

[certains modules)

* Comprend une durCe de sCchage d'environ 30 minutes.

** Le nombre de remplissages varie selon le degr6 de salet6 de chaque charge.

Remarques :

• Selon la tempCrature de I'eau, il pourra y avoir une augmentation de la durCe du cycle pour amener I'eau _ la tempCrature

souhaitCe.

• Seuls les cycles certifiCs suivants ont 6t6 con£us pour r@ondre aux exigences d'assainissement NSF (NSF/ANSI 184 - lave-

vaisselle rCsidentiel) : Lavage intense, Lavage normal et Lavage 16ger.

Options

En plus de choisir un cycle, choisir, parmi les options suivantes disponibles, toutes celles qui seront n_cessaires selon la

charge en cours.

Hi Temp Wash Tousles cycles

(saul Rinse Only)

(certains modules)

Heated Dry

[Sbchage avec chaleur)

La fonction Hi Temp Wash fait en sorte que I'eau soit plus chaude au cours du

cycle de lavage, assure une temp@ature idCale pour des lavages et des sCchages

optimaux. SClectionner pour ajouter un rin£age supplCmentaire au cycle. Un

rin£age supplementaire permet d'ameliorer les resultats en cas d'eau dure.

Pour de meilleurs resultats de sechage, selectionner cette option. Lorsque Heated

Dry (SCchageavec chaleur) n'est pas choisi, il peut 6tre nCcessaire de sCcher

la main certains articles comme ceux en plastique et ceux avec surface non

adherente. Plus d'humidite peut aussi rester sur I'int@ieur du lave-vaisselle. Dans

les modules avec int@ieur en plastique, il est normal que de la vapeur s'Cchappe

de I'event de la porte pendant que la chaleur s_che la vaisselle. De la vapeur

s'Cchappera mCmesi I'option Heated Dry n'est pas sClectionnCe.

L'option peut 6tre utilisCe pour mettre le cycle automatiquement en marche, plus

tard. Voir les instructions au-dessous.

Tousles cycles

(sauf Rinse Only)

(certains modules)

Delay Tousles cycles

[Demarrage differe)

Tough ScrubM°/ SClectionner cette option Iors du lavage de vaisselle avec des taches tenaces Tousles cycles

Tough Scrub PlusMc Selon le cycle selectionnC, cette option augmente la durCe du lavage et/ou

[certains modbles) la temperature.

Sanitize Assainissement de la vaisselle. Lorsque le contrCleur du cycle reconnait que Tousles cycles

[Lavage sanitaire) les bonnes conditions ont et6 atteintes, le temoin lumineux Sanitized s'allume

[certains modules) la fin du cycle. Le lavage assainissant peut ne pas avoir lieu en cas d'interruption

du cycle, de panne de courant ou si la temperature d'arrivCed'eau est inferieure

49° C (120° F).

START/CANCEL Demarre et arrCte le lave-vaisselle. Voir les explications _ la page 15 sous Tousles cycles

[Mise en Utilisation du lave-vaisselle.

Marche/Annulation)

Control Lock Option Verrouille les touches de corrlmande pour empCcher une utilisation non souhaitCe. Tousles cycles

[terrains modules) Voir les instructions _ la page 19.

Cycles,optionsettemoinslumineux

Delay (D marmge differed

I'option Delay peut etre utilisee pour mettre le cycle

automatiquement en marche, plus tard, pour reduire

raccumulation de chaleur pendant la journee dans la

maison, ou pour bendicier de co0ts energetiques reduits,

si ceci est disponible dans la region. Cette option est aussi

utile pour conserver reau chaude, _ des periodes

d'utilisation domestique elevee (douches, lessive).

R_glage d'un d_marrage Diff_re :

1. Selectionner le cycle et les options appropriees pour la

charge. Fermer la porte.

2. Appuyer sur la touche Delay et selectionner la duree

d'attente souhaitee.

3. Le temoin lumineux Delay et I'affichage du compte _]

rebours (certains modeles) clignoteront jusqu'_ ce que

ron appuie sur la touche START/CANCEL (Mise en

Marche/Annulation).

4. Une fois que I'on a appuye sur la touche

START/CANCEL le temoin lumineux s'arrete de

clignoter et le compte _]rebours commence. Le temoin

lumineux Delay restera allume jusqu'a la fin du

compte a rebours.

Annulation d'un d_marrage diff_r_ et d'un cycle :

• Appuyer une fois sur la touche START/CANCEL pour

evacuer I'eau et arreter le lave-vaisselle.

• Appuyer deux fois sur la touche START/CANCEL pour

arreter le lave-vaisselle sans evacuer I'eau.

Option de verrouillage de

commandes [certains modules)

Les touches de commande peuvent etre verrouillees

pour empecher toute utilisation non autorisee. Si cette

fonction est activee entre les cycles, le lave-vaisselle ne

peut pas etre utilise jusqu'au deverrouillage des

commandes. Au besoin, les commandes peuvent etre

verrouillees apres le demarrage d'un cycle ou d'un

depart differ&

R_glage du verrouillage des commandes :

1.Appuyer sur la touche Heated Dry (Sechage avec

chaleur) pendant trois secondes.

2. Un temoin lumineux situe _ cote de I'ic0ne de

verrouillage s'allume Iorsque les commandes sont

verrouillees.

Annulation :

5. Le cycle commencera automatiquement _]rexpiration

du delai d'attente.

1. Appuyer sur la touche Heated Dry pendant trois

secondes.

Remarque : Si trente secondes s'ecoulent entre un

reglage du cycle et des options et une pression sur la

touche START/CANCEL le lave-vaisselle se mettra

I'arret.

Annulation d'un d_marmge diff_r_ :

Lors du compte _ rebours, appuyer sur la touche Delay

de nouveau. Le temoin lumineux s'eteindra et le cycle

commencera ou reprendra immediatement.

2. Le temoin lumineux s'eteint.

Remarques :

• Si I'on appuie sur la touche d'un cycle ou d'une option

apres le verrouillage des commandes, le temoin

lumineux situe _ cote de I'ic0ne de verrouillage

clignotera cinq lois. Sur certains modeles avec

I'affichage du compte _ rebours, un _{L >>clignote

I'affichage en meme temps que le temoin lumineux de

verrouillage.

• Cette option ne verrouille pas la porte, uniquement les

commandes du lave-vaisselle.

T moins lumineux/affichage [certains modbles)

S'allume _ la fin du cycle et reste allume _ moins que la porte ne reste ouverte en continu pendant

Clean [Netteyage) 30 secondes.

Wash/Dry [Lavage/Sechage) S'allume durant toutes les portions de lavage, de rin_.age et de sechage du cycle.

Sanitized [Lavage Sanitaire) S'allume _ la fin du cycle Iorsque toutes les conditions ont 6t6 respectCes pour un lavage sanitaire. Le

(:certains modules) tCmoin lumineux reste allume _ moins que la porte ne reste ouverte en continu pendant 30 secondes.

Remarques :

• LorsqueSanitize est choisi, les cycles sont contrCles pour s'assurer du lavage sanitaire. Le tCmoin lumineux Sanitized ne s'allume pas si

les exigences du lavage sanitaire ne sont pas respectCes. Ceci peut se produire si le cycle est interrompu, en cas de panne de courant

ou d'arrivee d'eau _ une tempCrature infCrieure _ 49° C 020 ° F).

• Les tCmoins lumineux Clean et Sanitized (certains modules] ne se rCallument pas _ la suite d'une panne de courant et tant que le

prochain cycle n'est pas en marche.

La page charge ...

Maytag MDB7751AWW Le manuel du propriétaire

Marque: Maytag

Modèle: MDB7751AWW

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MDB7751AWW Owner's manual
español: Maytag MDB7751AWW El manual del propietario

Documents connexes

Autres documents

Crosley CDU650AWB Le manuel du propriétaire